Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MELTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Mechanical response of 99.999% purity aluminum under dynamic uniaxial strain and near melting temperatures

In this study, a series of reverse geometry normal plate impact experiments are employed to investigate the incipient plastic behavior of commercial purity polycrystalline aluminum under ultra-high strain-rates (~105 /s) and test temperatures up to melt (i.e. 643 °C). The applied stress at the aluminum/target interface, as inferred from the measured normal free-surface particle velocity record, shows progressive weakening with increasing test temperatures ranging from 23–620 °C; at higher temperatures (470–620 °C) this rate of weakening is observed to decrease, and at the highest test temperatures employed in the study, i.e. temperatures approaching the melt point of aluminum (643 °C), a net increase in the longitudinal stress is observed. Additionally, estimates of longitudinal elastic impedance of the sample material, as inferred via impedance matching from the particle velocity states at shock plateau show similar monotonic decrease with temperature, except for the highest test temperature case, in which reversal of this trend is observed. Though slight, these noticeable changes in the impedance, and stress/velocity states likely indicate variances in the strengthening/hardening response of the material, which can be linked to transition in the dominant plastic flow mechanisms as the sample approaches the melting point. Scanning electron microscopy of the impact surface of the post-test samples reveal coarsening of the sample grains due to static recrystallization during the heating phase of the experiment. Additional experiments are performed on annealed specimens to probe the effects of microstructural changes, i.e. grain size, and/or relief of residual strains in the interpretation of the measured response of aluminum. Finally, the results, which show a decrease in the longitudinal acoustic impedance, and decrease in the levels of stress/particle velocity under shock loading, indicate that the effects of annealing may play a role in the observed response by promoting softening of the dynamic strength, and/or lessening of the rate of hardening in a post-yield regime.

36 MATERIALS SCIENCE↗

Highly dense, inexpensive composites via melt infiltration of Ni into WC/Fe preforms

Generally, WC-based composites use Co as the metal binder phase to consolidate using liquid-phase sintering with a small percentage of Co, but a potentially lower cost binder phase can be made with a different approach when using large amount of metal binder phase. FeNi as a metal binder material is much cheaper than Co. WC can be liquid-phase sintered and melt infiltrated with FeNi, but by making FeNi in situ , costs lower even further. Composites of WC-(Fe-Ni) were made by first pressing a mixture of WC and Fe powders and subsequently melt infiltrating Ni in an amount corresponding to less volume than the porosity of the preform to ensure high WC content. The research objective was to make highly dense composites via melt infiltration with a low-cost metal binder phase in situ . This approach has the potential to make fully dense composites, rather than hardmetals, with suitable properties at lower costs. The density and hardness are 97.4%TD and 6.72 GPa, respectively.

36 MATERIALS SCIENCE↗

Dissolution retardation of solid silica during glass batch-melting

During glass-batch melting, solid silica (quartz) usually dissolves last. A retardation function was defined as a measure of the progressive inhibition of silica dissolution that occurs during batch melting. This function is based on the comparison of the measured rate of dissolution of silica particles with the hypothetical diffusion-controlled volume flux from regularly distributed particles with uniform concentration layers around them. The severe inhibition of silica dissolution has been attributed to the irregular spatial distribution of silica particles that is associated with the formation of nearly saturated melt at a portion of their surfaces. Irregular shapes and unequal sizes of particles also contribute to their extended lifetime.

36 MATERIALS SCIENCE↗

Temperature and Composition Dependence Modeling of Viscosity and Electrical Conductivity of Low-Activity Waste Glass Melts

The development of models that accurately relate the properties of a glass melt to its temperature and composition is important for glass formulation, melter control, and modeling the melt flow, refractory corrosion, and production rate. Using a database consisting of more than 4,000 data points measured between 900 °C and 1250 °C for over 600 unique low-activity waste glass compositions, we developed models for the melt viscosity and electrical conductivity. Models based on the Gaussian process regression approach outperformed models based on the Vogel–Fulcher–Tammann equation according to four standard metrics and yielded reliable prediction intervals. The models found primarily linear effects between properties and individual components, except for the effect of the Na 2 O mass fraction on the electrical conductivity. The effects were found to be consistent with current theories on physical processes involved with those properties.

36 MATERIALS SCIENCE↗

Melting curve of silicon to 15 GPa determined by two-dimensional angle-dispersive diffraction using a Kawai-type apparatus with X-ray transparent sintered diamond anvils

The melting curve of silicon has been determined up to 15 GPa using a miniaturized Kawai-type apparatus with second-stage cubic anvils made of X-ray transparent sintered diamond. Our results are in good agreement with the melting curve determined by electrical resistivity measurements [V.V. Brazhkin, A.G. Lyapin, S.V. Popova, R.N. Voloshin, Nonequilibrium phase transitions and amorphization in Si, Si/GaAs, Ge, and Ge/GaSb at the decompression of high-pressure phases, Phys. Rev. B 51 (1995) 7549] up to the phase I (diamond structure)-phase II ({beta}-tin structure)-liquid triple point. The triple point of phase XI (orthorhombic, Imma)-phase V (simple hexagonal)-liquid has been constrained to be at 14.4(4) GPa and 1010(5) K. These results demonstrate that the combination of X-ray transparent anvils and monochromatic diffraction with area detectors offers a reliable technique to detect melting at high pressures in the multianvil press.

36 MATERIALS SCIENCE↗

Gallium composition dependence of crystallographic and thermoelectric properties in polycrystalline type-I Ba{sub 8}Ga{sub x}Si{sub 46-x} (nominal x=14-18) clathrates prepared by combining arc melting and spark plasma sintering methods

The gallium composition dependence of crystallographic and thermoelectric properties in polycrystalline n-type Ba{sub 8}Ga{sub x}Si{sub 46-x} (nominal x=14-18) compounds with the type-I clathrate structure is presented. Samples were prepared by combining arc melting and spark plasma sintering methods. Powder x-ray diffraction, Rietveld analysis, scanning electron microscopy, and energy-dispersive x-ray spectroscopy show that the solubility limit of gallium in the type-I clathrate phase is close to x=15, which is slightly higher than that for a single crystal. The carrier concentration at room temperature decreases from 2 Multiplication-Sign 10{sup 21} cm{sup -3} to 4 Multiplication-Sign 10{sup 20} cm{sup -3} as the Ga content x increases. The Seebeck coefficient, the electrical conductivity, and the thermal conductivity vary systematically with the carrier concentration when the Ga content x varies. The effective mass (2.0m{sub 0}), the carrier mobility (10 cm{sup 2} V{sup -1} s{sup -1}), and the lattice thermal conductivity (1.1 W m{sup -1} K{sup -1}) are determined for the Ga content x=14.51. The dimensionless thermoelectric figure of merit ZT is about 0.55 at 900 K for the Ga content x=14.51. The calculation of ZT using the experimentally determined material parameters predicts ZT=0.8 (900 K) at the optimum carrier concentration of about 2 Multiplication-Sign 10{sup 20} cm{sup -3}. - Graphical abstract: The gallium composition dependence of crystallographic and thermoelectric properties is presented on polycrystalline n-type Ba{sub 8}Ga{sub x}Si{sub 46-x} with the type-I clathrate structure prepared by combining arc melting and spark plasma sintering methods. The thermoelectric figure of merit ZT reaches 0.55 at 900 K due to the increase in the Ga content (close to x=15), and a calculation predicts further improvement of ZT at the optimized carrier concentration. Highlights: Black-Right-Pointing-Pointer Crystallographic properties of Ba{sub 8}Ga{sub x}Si{sub 46-x} clathrates are characterized. Black-Right-Pointing-Pointer Arc melting and spark plasma sintering process enables increase of Ga content. Black-Right-Pointing-Pointer We elucidate the Ga composition dependence of thermoelectric properties. Black-Right-Pointing-Pointer Thermoelectric figure of merit ZT is improved due to the increased Ga content. Black-Right-Pointing-Pointer Calculation predicts a potential ZT=0.8 at 900 K at optimized carrier concentration.

36 MATERIALS SCIENCE↗

Solidification observations and sliding wear behavior of vacuum arc melting processed Ni-Al-TiC composites

Monolithic Ni{sub 3}Al and Ni-25 at.%Al intermetallic matrix TiC-reinforced composites were successfully produced by vacuum arc melting. TiC crystals were formed through a dissolution-reprecipitation mechanism and their final morphology is explained by means of a) Jackson's classical nucleation and growth phenomena and b) solidification rate considerations. The TiC presence altered the matrix microconstituents most likely due to specific melt-particle interactions and crystal plane epitaxial matching. TiC particles caused a significant decrease on the specific wear rate of the monolithic Ni{sub 3}Al alloy and the possible wear mechanisms are approached by means of a) surface oxidation, b) crack/flaws formation, c) material detachment and d) debris-counter surfaces interactions. - Highlights: Black-Right-Pointing-Pointer Vacuum arc melting (VAM) of Ni-Al based intermetallic matrix composite materials. Black-Right-Pointing-Pointer Solidification phenomena examination. Black-Right-Pointing-Pointer TiC crystal formation and growth mechanisms. Black-Right-Pointing-Pointer Sliding wear examination.

36 MATERIALS SCIENCE↗

Effect of build geometry on the β-grain structure and texture in additive manufacture of Ti-6Al-4V by selective electron beam melting

With titanium alloys, the solidification conditions in Additive Manufacturing (AM) frequently lead to coarse columnar β-grain structures. The effect of geometry on the variability in the grain structure and texture, seen in Ti-6Al-4V alloy components produced by Selective Electron Beam Melting (SEBM), has been investigated. Reconstruction of the primary β-phase, from α-phase EBSD data, has confirmed that in bulk sections where in-fill “hatching” is employed growth selection favours columnar grains aligned with an <001> {sub β} direction normal to the deposited powder layers; this results in a coarse β-grain structure with a strong < 001 > {sub β} fibre texture (up 8 x random) that can oscillate between a near random distribution around the fibre axis and cube reinforcement with build height. It is proposed that this behaviour is related to the highly elongated melt pool and the raster directions alternating between two orthogonal directions every layer, which on average favours grains with cube alignment. In contrast, the outline, or “contour”, pass produces a distinctly different grain structure and texture resulting in a skin layer on wall surfaces, where nucleation occurs off the surrounding powder and growth follows the curved surface of the melt pool. This structure becomes increasingly important in thin sections. Local heterogeneities have also been found within different section transitions, resulting from the growth of skin grain structures into thicker sections. Texture simulations have shown that the far weaker α-texture (∼ 3 x random), seen in the final product, arises from transformation on cooling occurring with a near random distribution of α-plates across the 12 variants possible from the Burgers relationship. - Highlights: • Distinctly different skin and bulk structures are produced by the contour and hatching passes. • Bulk sections contain coarse β-grains with a < 001 > fibre texture in the build direction. • This oscillates between a random distribution around the axis and cube reinforcement. • In the skin layer nucleation occurs off the surrounding powder bed and growth occurs inwards. • Simulations show that a weak α-texture results from a random distribution across habit variants.

36 MATERIALS SCIENCE↗

CoCrMo cellular structures made by Electron Beam Melting studied by local tomography and finite element modelling

The work focuses on the structural and mechanical characterization of Co-Cr-Mo cellular samples with cubic pore structure made by Electron Beam Melting (EBM). X-ray tomography was used to characterize the architecture of the sample. High resolution images were also obtained thanks to local tomography in which the specimen is placed close to the X-ray source. These images enabled to observe some defects due to the fabrication process: small pores in the solid phase, partially melted particles attached to the surface. Then, in situ compression tests were performed in the tomograph. The images of the deformed sample show a progressive buckling of the vertical struts leading to final fracture. The deformation initiated where the defects were present in the strut i.e. in regions with reduced local thickness. The finite element modelling confirmed the high stress concentrations of these weak points leading to the fracture of the sample. - Highlights: • CoCrMo samples fabricated by Electron Beam Melting (EBM) process are considered. • X-ray Computed Tomography is used to observe the structure of the sample. • The mechanical properties are tested thanks to an in situ test in the tomograph. • A finite element model is developed to model the mechanical behaviour.

36 MATERIALS SCIENCE↗

Size dependence of microstructure of AlSi10Mg alloy fabricated by selective laser melting

Highlights: • Plate-shaped samples with various widths were fabricated via selective laser melting. • The hardness of AlSi10Mg samples slightly decreased with decreasing sample width. • The alloy sample size had a slight effect on microstructure of the α-Al matrix. • Precipitation of Si phase in α-Al matrix was enhanced by reducing the sample size. • The softening by reducing sample size is likely due to their slower cooling rate. - Abstract: In order to investigate the size dependence of microstructure of the AlSi10Mg alloy fabricated by selective laser melting (SLM) combined with a powder bed technique, plate-shaped AlSi10Mg alloy samples with various widths (ranging from approximately 10 mm to 0.3 mm) were produced in this study. All the fabricated samples exhibited characteristic microstructural morphologies consisting of melt pools with columnar α-Al grains surrounded by fine eutectic Si particles, whereas their sample sizes had a relatively small effect on the texture and average grain size of the α-Al matrix. However, the formation of fine Si precipitates inside the columnar α-Al grains was observed more often for the smaller-sized samples, which could be a possible dominant contributor to the observed softening of the sample by reducing sample size. The obtained results were utilized for discussing the size dependence of the strength of the SLM-manufactured porous alloy samples.

36 MATERIALS SCIENCE↗

Microstructure and fracture properties of open-cell porous Ti-6Al-4V with high porosity fabricated by electron beam melting

Highlights: • The Ti-6Al-4V foams with 80% high porosity are prepared by electron beam melting. • The ligament width appears to play the major role for mechanical properties. • The work of fracture is a linear function of ligament width and roughness/width ratio. - Abstract: The open-cell porous Ti-6Al-4V structure with high porosity, intended to be applied as replacement for human cancellous bone, were fabricated by electron beam melting (EBM). Computer aided design (CAD) was applied to design porous structures using the same unit cell with different unit cell sizes from 2.5 to 4 mm, different ligament widths from 600 to 900 μm, and different pore sizes from 1200 to 1800 μm, in order to achieve high porosity of 80% in avoiding the stress shielding effect. In comparison with the CAD designs and the EBM samples, there were minor discrepancies in terms of pore size and ligament width, mainly a result of melting pool. The measured data on the Young's modulus and yield strength of the EBM porous samples can be predicted by the Gibson and Ashby model. All samples with high porosity were found to match well with cancellous bone, with Young's modulus of 2 GPa and yield stress of 31 MPa, effective to diminish the risk of stress shielding effect. For porous EBM sample with high 80% porosity, the work of fracture can increase from 15.9 to 47.6 kJ/m{sup 2} with increasing ligament width from 600 to 900 μm.

36 MATERIALS SCIENCE↗

A melting-like process and the local structures during the anatase-to-rutile transition

Highlights: • The maximum size of anatase crystallites is more useful to describe the phase stability than the traditional critical size. • The melting-like process accelerates the phase transition from anatase to rutile. • The cis-coordinated anatase is transformed to trans-coordinated rutile by torsion & rotation of TiO{sub 6} octahedra in anatase. Phase transition of titanium oxide from anatase to rutile was investigated by using transmitted electron microscope (TEM), scanning electron microscope (SEM) and X-ray diffraction (XRD), in combination with the atomic pair distribution function (PDF) technique. The transition range is about 528–805 °C and the critical size is ~73 nm for the sol-gel samples calcined for 6 h. A melting-like process was evidently observed in the transition samples by SEM and it will speed up the phase transition. PDF reveals that anatase crystallites are packed by neighbouring TiO{sub 6} octahedra in a cis-coordinated way. Anatase crystallites larger than the critical size will be unstable and transform into rutile in a trans-coordinated way by torsion and rotation of part of octahedra and it will rapidly spread the entire crystallites driven by a melting-like process. We suggest the maximum size of anatase will be more technically useful for the description of the phase stability from anatase to rutile because unstable small anatase crystals are consumed during longer calcination process to grow the larger anatase crystals.

36 MATERIALS SCIENCE↗

Dual X-ray computed tomography-aided classification of melt pool boundaries and flaws in crept additively manufactured parts

In metal additive manufacturing (AM), understanding the process-structure-performance relationships requires a combination of multi-scale characterization techniques that allows for the measurement of the melt pool shape and boundary and classifying various defects and flaws in the AM parts. Such approaches can be destructive, only 2D in nature, or have a small field of view and can be complex to co-register and analyze. Here, in this work, we present a non-destructive 3D inspection technique that employs dual-energy X-ray computed tomography (XCT) along with a model-based iterative reconstruction (MBIR) and a new segmentation algorithm. The proposed approach and algorithm are not only capable of classifying and quantifying flaws such as pores, cracks, and inclusions, but they also allow for the extraction of microstructural features such as melt pool boundaries (MPB) and melt pool regions (MPR), that can help understand process-structure-performance relationships for alloys under study. As an exemplar application, we employed the method for characterization of an additively manufactured aluminum alloy crept under tensile stress at 300 °C for 1064 h. Our results demonstrate high quality segmentation and classification of various flaws and MPB and MPR, for the first time, using 3D X-ray CT inspection. The delineated MPB and MPR in the crept samples reveal the preferential growth paths of cracks that formed during creep deformation. The technique was used for successfully quantifying the characteristics (number of defects, their density, volume fraction, etc.) of the manufacturing-induced pores and creep-induced cracks, which is necessary to better understand the creep failure mechanisms of the material.

36 MATERIALS SCIENCE↗

Correlating melting and collapse of charge ordering with magnetic transitions in La{sub 0.5-x}Pr{sub x}Ca{sub 0.5}MnO{sub 3}

Highlights: • Concept of normalized magnetization is introduced to explain relative magnetic transitions. • Coexistence of two magnetic modes is correlated with the magnetic transitions and MIT. • Field induced melting and collapse of charge ordered antiferromagnetic (CO-AFM) state into ferromagnetic (FM) state is conferred. - Abstract: The magnetic properties of polycrystalline La{sub 0.5-x}Pr{sub x}Ca{sub 0.5}MnO{sub 3} material are investigated at different temperatures. The existence of magnetically diverse phases associated with various relaxation modes and their modulation with temperature and doping is analyzed. La{sub 0.5}Ca{sub 0.5}MnO{sub 3} exhibited field induced melting and collapse of charge ordered antiferromagnetic (CO-AFM) phase into ferromagnetic (FM) state. This phenomenon results in lowering of Neel’s temperature (T{sub N}) along with changes in the slope of magnetic moment with temperature. Using normalized M(T) curves, the variation and interplay of charge ordered temperature (T{sub CO}), Curie temperature (T{sub C}) and T{sub N} is conferred. The coexistence of two magnetic modes is explained as major ingredient for the magnetic transitions as well as metal to insulator transition (MIT); where melting and collapse of charge ordering is conversed as basic feature in these Praseodymium (Pr) doped La{sub 0.5}Ca{sub 0.5}MnO{sub 3} materials.

36 MATERIALS SCIENCE↗

Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting

In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.

36 MATERIALS SCIENCE↗

Impact of Nanosilicates on Poly(vinylidene fluoride) Crystal Polymorphism: Part 1. Melt-crystallization at High Supercooling

Polymorphism of poly(vinylidene fluoride), PVDF, in the presence of Lucentite STN organically modified silicate (OMS) is investigated for PVDF nanocomposites melt-crystallized at high supercooling temperatures where neat PVDF crystallizes exclusively in the alpha crystalline phase. Nanocomposites were prepared from solution with 0-1.0 wt% OMS composition. Here we observed that clay addition promotes gamma phase formation in nanocomposites melt-crystallized at high supercooling (i.e., at low crystallization temperature), whereas previously we showed that even small amount of nanosilicates resulted in beta phase formation in cold-crystallized PVDF nanocomposites. Wide-angle X-ray scattering (WAXS), Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) studies showed that {alpha}- and {gamma}-phases co-existed in nanocomposites containing up to 0.1 wt% OMS, and the amount of {alpha}-crystals substantially diminished for higher OMS content. Formation of {gamma}-crystal phase was confirmed with morphologic observation of spherulites of low-birefringence using polarizing optical and atomic force microscopies, and their crystalline structures were verified by FTIR and Raman microscopic spectroscopy. We also address in this work the ambiguities in assessing PVDF crystallographic phases, and correct the phase identification errors which have persisted up to this point in the literature based on melting point confusion. The crystal phase identification for PVDF nanocomposites is discussed and clarified, based on X-ray scattering, vibrational spectra, and thermal analysis. For reference, we provide a vibrational band list, indicating the close, or overlapping bands, of the three phases of PVDF: {alpha}, {beta} and {gamma}.

36 MATERIALS SCIENCE↗

Melting Curve and Phase Relations of Fe-Ni Alloys: Implications for the Earth's Core Composition

We discuss that nickel is the second most abundant element in the Earth's core. However, the properties of Fe-Ni alloys are still poorly constrained under planetary cores conditions, in particular concerning the effect of Ni on the melting curve of Fe. Here we show that Ni alloying up to 36 wt% does not affect the melting curve of Fe up to 100 GPa. However, Ni strongly modifies the hexagonal-closed-packed/face-centered-cubic (hcp/fcc) phase boundary, pushing the hcp/fcc/liquid triple point of Fe-20wt%Ni to higher pressures and temperatures. Our results allow constraining the triple point for Fe-10wt%Ni, a composition relevant for the Earth interior, and point out a decrease of the melting temperature at core-mantle boundary by 400 K with respect to pure Fe. A lower amount of light elements than previously predicted is thus required to reduce the crystallization temperature of core materials below that of a peridotitic lower mantle, in better agreement with geochemical observations.

36 MATERIALS SCIENCE↗

A model for the latent heat of melting in free standing metal nanoparticles

Nanoparticles of many metals are known to exhibit scale dependent latent heats of melting. Analytical models for this phenomenon have so far failed to completely capture the observed phenomena. Here we present a thermodynamic analysis for the melting of metal nanoparticles in terms of their internal energy and a scale dependent surface tension proposed by Tolman. The resulting model predicts the scale dependence of the latent heat of melting and is confirmed using published data for tin and aluminum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗