Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Numerical simulation of porosity and permeability evolution of Mount Simon sandstone under geological carbon sequestration conditions

A numerical model was developed with the use of reactive transport code CrunchFlow to estimate porosity, permeability and mineral composition changes of Mount Simon sandstone under typical geological carbon sequestration conditions (P = 23.8 MPa and T = 85 °C). The model predicted a permeability decrease from 1.60 mD to 1.02 mD for the Mount Simon sandstone sample in a static batch reactor after 180 days of exposure to CO 2 -saturated brine, which is consistent with measured permeability results. Model-predicted solution chemistry results were also consistent with laboratory-measured solution chemistry data. SiO 2 (am) was the primary mineral that causes permeability decrease, followed by kaolinite. Both SiO 2 (am) formation and kaolinite formation were attributed to the dissolution of quartz and feldspar. This article shows that the formation of SiO 2 (am) and kaolinite in the pore space of host rock is possible under typical CO2 sequestration conditions. SiO 2 (am) and kaolinite precipitation at the CO 2 plume extent could reduce the permeability of host rock and improve lateral containment of free-phase CO 2 , contributing to overall security of CO 2 storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Amantadine interactions with phase separated lipid membranes

Amantadine, a small amphilphic organic compound that consists of an adamantane backbone and an amino group, was first recognized as an antiviral in 1963 and received approval for prophylaxis against the type A influenza virus in 1976. Since then, it has also been used to treat Parkinson’s disease-related dyskinesia and is being considered as a treatment for corona viruses. Since amantadine usually targets membrane-bound proteins, its interactions with the membrane are also thought to be important. Biological membranes are now widely understood to be laterally heterogeneous and certain proteins are known to preferentially co-localize within specific lipid domains. Does amantadine, therefore, preferentially localize in certain lipid composition domains? To address this question, here, we studied amantadine’s interactions with phase separating membranes composed of cholesterol, DSPC (1,2-distearoyl-sn-glycero-3-phosphocholine), POPC (1-palmitoyl-2-oleoyl-glycero-3-phosphocholine), and DOPC (1,2-dioleoyl-sn-glycero-3-phosphocholine), as well as single-phase DPhPC (1,2-diphytanoyl-sn-glycero-3-phos-phocholine) membranes. From Langmuir trough and differential scanning calorimetry (DSC) measurements, we determined, respectively, that amantadine preferentially binds to disordered lipids, such as POPC, and lowers the phase transition temperature of POPC/DSPC/cholesterol mixtures, implying that amantadine increases membrane disorder. Further, using droplet interface bilayers (DIBs), we observed that amantadine disrupts DPhPC membranes, consistent with its disordering properties. Finally, we carried out molecular dynamics (MD) simulations on POPC/DSPC/cholesterol membranes with varying amounts of amantadine. Consistent with experiment, MD simulations showed that amantadine prefers to associate with disordered POPC-rich domains, domain boundaries, and lipid glycerol backbones. Since different proteins co-localize with different lipid domains, our results have possible implications as to which classes of proteins may be better targets for amantadine.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Continuum stress intensity factors from atomistic fracture simulations

Stress intensity factors (SIFs) are utilized in continuum fracture mechanics to quantify the stress fields surrounding a crack in a homogeneous material in the linear elastic regime. Critical values of the SIFs define an intrinsic measure of the resistance of a material to propagate a crack. At atomic scales, yet, fracture occurs as a series of atomic bonds breaking, differing from the continuum description. As a consequence, a formal analog of the continuum SIFs calculated from atomistic simulations can have spatially localized, microstructural contributions that originate from varying bond configurations. The ability to characterize fracture at the atomic scale in terms of the SIFs offers both an opportunity to probe the effects of chemistry, as well as how the addition of a microstructural component affects the accuracy. We present a novel numerical method to determine SIFs from molecular dynamics (MD) simulations. The accuracy of this approach is first examined for a simple model, and then applied to atomistic simulations of fracture in amorphous silica. MD simulations provide time and spatially dependent SIFs, with results that are shown to be in good agreement with experimental values for fracture toughness in silica glass.

42 ENGINEERING↗

Effect of CO 2 on the water slip flow at silica surfaces for nanometer slit pores of talc

In our previous study, Molecular Dynamics (MD) simulated water flow with no dissolved gas in nanometer slit pores of the hydrophobic talc surfaces revealed a slip length of about 0.5 nm, which is close to the size of “water exclusion zone” but much less than experimental slip length. Atomic Force Microscopy (AFM) imaging confirmed the presence of pancake shape nanobubbles at the hydrophobic talc (001) surface (size from tens to hundreds of nanometers). The effect of CO 2 on water slip flow in talc nanopores is reported to reveal the importance of dissolved gas for confined fluid flow. MD simulated 7 nm CO 2 nanobubbles were found to attach and spread at the talc (001) surface, consistent with the AFM observation. Simulated CO 2 saturated water flow in the slit pores of talc (001) surfaces predicted the generation of CO 2 nanobubbles at the end of the slit pore, due to the stabilization of a CO 2 film at the talc (001) surfaces and a water barrier at the edge surfaces of talc. A “critical thickness” of about 1.5 nm was found for CO 2 nanobubbles to be stabilized at the end of the talc (001) surface. With 1.5 nm CO 2 nanobubbles at the talc (001) surface of a 6 nm slit pore, a water slip length of 1.8 nm was determined. Furthermore, the nanometer slit pore simulations with dissolved CO 2 in water revealed an increased slip length. It is expected that an increased slip length value would be found with an increased CO 2 film thickness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hot spot and temperature analysis of shocked hydrocarbon polymer foams using molecular dynamics simulation

Hydrocarbon polymers, foams and nanocomposites are increasingly being subjected to extreme environments. Molecular scale modeling of these materials offers insight into failure mechanisms and complex response. Prior classical molecular dynamics (MD) simulations of the principal shock Hugoniot for two hydrocarbon polymers, polyethylene (PE) and poly (4-methyl-1-pentene) (PMP) have shown good agreement with density functional theory (DFT) calculations and experiments conducted at Sandia National Laboratories. We extended these results to include low-density polymer foams using nonequilibrium MD techniques and found good quantitative agreement with experiment. Here, we have measured the local temperature during void collapse to investigate the formation of hot spots and their relationship to polymer dissociation in foams.

36 MATERIALS SCIENCE↗

Dynamical properties of AlN nanostructures and heterogeneous interfaces predicted using COMB potentials

A new empirical variable charge potential has been developed for AlN within the third-generation charge optimized many-body (COMB3) potential framework. We report the potential is able to reproduce the fundamental physical properties of AlN, including cohesive energy, elastic constants, defect formation energies, surface energies and phonon properties of AlN obtained from experiments and first-principles calculations. The thermodynamic properties of the Al(1 1 1)-AlN ( 1 0 1 ¯ 0 ) and Al 2 O 3 (0 0 0 1)-AlN ( 1 0 1 ¯ 0 ) interfaces and the tensile response of AlN nanowires and nanotubes are investigated in classical molecular dynamical (MD) simulations using this COMB3 potential. The results demonstrate that the potential is well suited to model heterogeneous materials in the Al–O–N system. Most importantly, the fully transferrable potential parameters can be seamlessly coupled with existing COMB3 parameters of other elements to enable MD simulations for an even wider range of heterogeneous materials systems.

36 MATERIALS SCIENCE↗

Tight-binding study of beryllium

In this work, we have applied the Naval Research Laboratory Tight-binding (NRL-TB) Method to the hcp alkaline-earth metal Beryllium. This approach consists of fitting to energy band and total energy data generated by the Linearized Augmented Plane Wave (LAPW) for the fcc, bcc, sc, and hcp structures as a function of volume. First, we found that using the Generalized Gradient Approximation (GGA) for the input data secures a better agreement to experimental volumes than the LDA. Second, we found that including small volumes to the fit is needed to get TB parameters that are transferable enough to successfully predict the energies of structures that were not fitted, and to perform molecular dynamics (MD) simulations. The non-orthogonal Hamiltonian obtained, is successful in correctly predicting the hcp lattice as the ground state of Be and finding eight other structures, that were not fitted to LAPW, positioned at higher energies. In addition, the NRL-TB produces accurate energy bands, densities of states, elastic constants, the Bain path and several quantities derived from MD simulations.

36 MATERIALS SCIENCE↗

Understanding the plasticity contributions during laser-shock loading and spall failure of Cu microstructures at the atomic scales

A hybrid atomic-scale and continuum modeling framework is used to study the microstructural evolution during the laser-induced shock deformation and failure (spallation) of copper microstructures. A continuum two-temperature model (TTM) is used to account for the interaction of Cu atoms with a laser in molecular dynamics (MD) simulations. The MD-TTM simulations study the effect of laser loading conditions (laser fluence) on the microstructure (defects) evolution during various stages of shock wave propagation, reflection, and interaction in single-crystal (sc) Cu systems. In addition, the role of the microstructure is investigated by comparing the defect evolution and spall response of sc-Cu and nanocrystalline (nc) Cu systems. The defect (stacking faults and twin faults) evolution behavior in the metal at various times is further characterized using virtual in situ selected area electron diffraction and x-ray diffraction during various stages of evolution of microstructure. Here, the simulations elucidate the uncertain relation between spall strength and strain-rate and the much stronger relation between the spall strength and the temperatures generated due to laser shock loading for the small Cu sample dimensions considered here.

36 MATERIALS SCIENCE↗

Unraveling the role of temperature on the onset of ejecta formation at atomic scales

Shock wave interactions with perturbations on a free surface can lead to the inversion and growth of the perturbation and eventual ejection of a jet of material, referred to as an ejecta microjet, from shocked surfaces. Here, this study carries out large-scale molecular dynamics (MD) simulations using single-crystal Cu and Sn systems with a pre-existing groove to characterize the localized gradients in temperatures and pressures generated that render the microjet formation. MD simulations are carried out for three loading orientations (along the [001], [011], and [111] directions) and shock pressures ranging from 16 GPa to 100 GPa to understand the role of temperatures generated at the groove vertex on the formation of ejecta. The simulations suggest that the interaction of the shock wave with the groove results in a localized increase in temperatures, leading to localized softening at the groove vertex and the generation of an ejecta microjet. For Cu systems, the simulations suggest that the orientation effects on shock wave structures, velocities, and localized softening affect the ejecta formation at low pressures. Jetting is only observed when temperatures at the groove vertex are high enough to induce localized softening (close to melting temperature), and the jet velocity increases with shock pressure. In contrast, the loading orientation is rendered inconsequential for Sn systems due to the melting of the material during shock compression at the pressures chosen. The jet velocities are similar, regardless of crystal orientation in Sn systems.

36 MATERIALS SCIENCE↗

Multi-scale computational analysis of unidirectional carbon fiber reinforced polymer composites under various loading conditions

In this study, a multi-scale computational analysis based on representative volume element (RVE) modeling and molecular dynamics (MD) simulations is developed to investigate the microscopic failure mechanisms of unidirectional (UD) carbon fiber reinforced polymer (CFRP) composites. The average properties of the 200-nm thickness interphase region between fiber and matrix are characterized through MD simulations and an analytical gradient model. The results demonstrate that the interphase region has higher Young’s modulus and strength, compared to the bulk matrix. This stiffened interphase region influences the composite response significantly. Specifically, the traditional two-phase model with zero-thickness interface fails to capture the stress-strain behavior compared to the experimental data. However, by adding the interphase region to a modified RVE model, the accuracy of simulation results will be improved significantly. Furthermore, a coupled experimental-computational micromechanics approach is adopted to calibrate and validate the cohesive parameters of the interface. By including the cohesive interface, our modified RVE model accurately captures the failure strength of the composites. Finally, different failure mechanisms for specimens are investigated using our multi-scale computational framework. In conclusion, the results show that the failure modes of UD CFRP composites are very complex and multiple failure mechanisms co-exist depending on the loading conditions, agreeing well with our experimental analyses.

36 MATERIALS SCIENCE↗

Sassena — X-ray and neutron scattering calculated from molecular dynamics trajectories using massively parallel computers

Massively parallel computers now permit the molecular dynamics (MD) simulation of multi-million atom systems on time scales up to the microsecond. However, the subsequent analysis of the resulting simulation trajectories has now become a high performance computing problem in itself. Here, we present software for calculating X-ray and neutron scattering intensities from MD simulation data that scales well on massively parallel supercomputers. The calculation and data staging schemes used maximize the degree of parallelism and minimize the IO bandwidth requirements. The strong scaling tested on the Jaguar Petaflop Cray XT5 at Oak Ridge National Laboratory exhibits virtually linear scaling up to 7000 cores for most benchmark systems. Since both MPI and thread parallelism is supported, the software is flexible enough to cover scaling demands for different types of scattering calculations. The result is a high performance tool capable of unifying large-scale supercomputing and a wide variety of neutron/synchrotron technology.

Computer Science↗

Implementing Molecular Dynamics on Hybrid High Performance Computers - Three-Body Potentials

The use of coprocessors or accelerators such as graphics processing units (GPUs) has become popular in scientific computing applications due to their low cost, impressive floating-point capabilities, high memory bandwidth, and low electrical power re- quirements. Hybrid high-performance computers, defined as machines with nodes containing more than one type of floating-point processor (e.g. CPU and GPU), are now becoming more prevalent due to these advantages. Although there has been extensive research into methods to efficiently use accelerators to improve the performance of molecular dynamics (MD) employing pairwise potential energy models, little is reported in the literature for models that include many-body effects. 3-body terms are required for many popular potentials such as MEAM, Tersoff, REBO, AIREBO, Stillinger-Weber, Bond-Order Potentials, and others. Because the per-atom simulation times are much higher for models incorporating 3-body terms, there is a clear need for efficient algo- rithms usable on hybrid high performance computers. Here, we report a shared-memory force-decomposition for 3-body potentials that avoids memory conflicts to allow for a deterministic code with substantial performance improvements on hybrid machines. We describe modifications necessary for use in distributed memory MD codes and show results for the simulation of water with Stillinger-Weber on the hybrid Titan supercomputer. We compare performance of the 3-body model to the SPC/E water model when using accelerators. Finally, we demonstrate that our approach can attain a speedup of 5.1 with acceleration on Titan for production simulations to study water droplet freezing on a surface.

Brown, W Michael↗

Distributed database kriging for adaptive sampling (D²KAS)

We present an adaptive sampling method supplemented by a distributed database and a prediction method for multiscale simulations using the Heterogeneous Multiscale Method. A finite-volume scheme integrates the macro-scale conservation laws for elastodynamics, which are closed by momentum and energy fluxes evaluated at the micro-scale. In the original approach, molecular dynamics (MD) simulations are launched for every macro-scale volume element. Our adaptive sampling scheme replaces a large fraction of costly micro-scale MD simulations with fast table lookup and prediction. The cloud database Redis provides the plain table lookup, and with locality aware hashing we gather input data for our prediction scheme. For the latter we use kriging, which estimates an unknown value and its uncertainty (error) at a specific location in parameter space by using weighted averages of the neighboring points. We find that our adaptive scheme significantly improves simulation performance by a factor of 2.5 to 25, while retaining high accuracy for various choices of the algorithm parameters.

36 MATERIALS SCIENCE↗

Aspherical particle models for molecular dynamics simulation

In traditional molecular dynamics (MD) simulations, atoms and coarse-grained particles are modeled as point masses interacting via isotropic potentials. For studies where particle shape plays a vital role, more complex models are required. Here, we describe a spectrum of approaches for modeling aspherical particles, all of which are now available (some recently) as options within the LAMMPS MD package. Broadly these include two classes of models. In the first, individual particles are aspherical, either via a pairwise anisotropic potential which implicitly assigns a simple geometric shape to each particle, or in a more general way where particles store internal state which can explicitly define a complex geometric shape. In the second class of models, individual particles are simple points or spheres, but rigid body constraints are used to create composite aspherical particles in a variety of complex shapes. This work discusses parallel algorithms and associated data structures for both kinds of models, which enable dynamics simulations of aspherical particle systems across a wide range of length and time scales. We also highlight parallel performance and scalability and give a few illustrative examples of aspherical models in different contexts.

74 ATOMIC AND MOLECULAR PHYSICS↗

A new self-adaptive reconstruction method to identify defects through Wigner–Seitz approach

A new self-adaptive reconstruction method based on local atomic structure at any given molecular dynamics (MD) step has been developed in this article. The method can be used in Wigner–Seitz defect analysis approach to correctly and efficiently explore the information of both point defects and complex defect clusters (e.g. dislocation loops and voids) formed after a displacement cascade where the cascade interacts with grain boundaries and/or dislocations. The algorithm and validation are provided in detail. Results for identification of radiation defects during and after cascades interacting with a dislocation network show that the new method can well recognize all simple and complex defects and defect clusters. Thus, this new method provides a totally new way to explore the density and size of radiation defects at atomic scale after complex MD evolution processes, providing correct information to understand and predict radiation damage in materials through atomic simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Numerical simulations of yield-based sooting tendencies of aromatic fuels using ReaxFF molecular dynamics

In this work, we present the first ReaxFF Molecular Dynamics (MD) simulations to quantitatively predict the sooting tendencies of various fuels. The specific sooting tendency metric used in this work is the Yield Sooting Index (YSI), which quantifies the effects of fuel molecular structure on soot yield. YSI has been experimentally measured and numerically simulated using computational fluid dynamics for a large range of fuels, but there is no existing reactive MD framework for YSI simulations. To adopt the experimental YSI concept, a multi-stage simulation procedure is designed using ReaxFF. As a proof-of-concept, toluene and phenol are selected as test fuels, since both have relatively well-understood reaction pathways. The ReaxFF YSI simulations are shown to capture key reaction events for both fuels selected that are consistent with existing chemical kinetic understanding. Toluene is shown to mostly retain its original aromatic ring structure and directly grow to larger aromatic compounds with multiple rings. On the other hand, the aromatic growth process from phenol is accompanied by carbon-loss reactions with CO release. In addition, a quantitative YSI formulation is also derived in ReaxFF and the ReaxFF-predicted YSI values are compared with measurement data and reasonably good agreement is achieved. The results reported in this work demonstrates that the ReaxFF-based framework can potentially be used to quantitatively predict the relative sooting tendencies, especially for fuels with unknown or poorly-known chemistry, to understand their sooting properties and in search for soot relevant reaction pathways from these fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Third-body stabilization of supercritical CO 2 in CO oxidation: development and application of a ReaxFF force field for the CO/O/CO 2 system

Supercritical CO 2 (scCO 2 ) plays a crucial role as a solvent in separation processes, advanced power cycles, and materials processing. Nonetheless, the atomistic comprehension of how the dense scCO 2 matrix influences the fundamental reaction of carbon monoxide (CO) is still insufficiently explored. Experimental studies and molecular dynamics (MD) simulations frequently fail to detect the highly reactive, transient intermediates, such as atomic oxygen (O), that drive these reactions. Here, to address this issue, we have developed a novel ReaxFF reactive force field for the CO 2 /CO/O system. The force field parameters were calibrated using density functional theory and second-order Møller-Plesset calculations to model CO 2 crystal properties, intermolecular interactions, bond dissociation curves, and reaction energy barriers. The force field reproduces the cohesive energy of the CO 2 crystal, the pressure characteristics of bulk scCO 2 , the equation-of-state behavior over a wide pressure–density range, the pressure dependence of the C–O bond length under compression, and the structural properties of liquid and scCO 2 , as documented by experiments, ab-initio MD, and prominent non-reactive models. The force field was subsequently applied to study the CO + O → CO 2 reaction. In a dilute environment, the reaction is inefficient as the newly formed CO 2 rapidly dissociates due to excess kinetic and potential energy acquired from the exothermic reaction. Conversely, in a dense scCO 2 environment, the surrounding matrix acts as an efficient third body, stabilizing the emerging CO2 product via molecular collisions. Statistical analysis confirms an average excess energy dissipation of 133.9 ± 3.6 kcal/mol over 112.4 ± 17.9 ps. Kinetic energy decomposition reveals that ∼ 92% of the excess kinetic energy is stored in internal (rotational and vibrational) degrees of freedom. This ReaxFF force field establishes a mechanistic foundation for third-body stabilization in dense reactive environments.

Chowdhury, Emdadul Haque [Pennsylvania State Univ.↗