Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETIC SHIELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Soil Activation and Groundwater Contamination at Brookhaven National Laboratory, Upton, New York

In November 1999, tritium (H-3) was detected in the groundwater near one of Brookhaven National Laboratory's (BNL) accelerator experiments at concentrations above the 20,000 pico curie per liter (pCi/L) Maximum Contaminant Level (MCL). Sodium-22 (Na-22) was also detected in the groundwater, but at concentrations well below the 400 pCi/L MCL. An investigation into the source of the contamination revealed that the tritium and sodium-22 originated from activated soil shielding located adjacent to the g-2 target building where approximately five percent of the beam was inadvertently striking one of the beam-line magnets. Rainwater was able to infiltrate the activated soils and carry the tritium and sodium-22 into the groundwater. The highest tritium level detected in groundwater during the 1999 investigation was nearly 1.8 million pCi/L. To prevent additional rainwater infiltration into the activated soil shielding, a concrete cap was constructed over the soil shielding in December 1999. Other corrective actions included refocusing the beam and improved beam loss monitoring to reduce additional soil activation, storm-water management improvements, and additional groundwater monitoring. From 2001 through 2004, three high concentration zones (or slugs) of tritium were observed passing through the groundwater monitoring well network immediately down-gradient of the source area, with a maximum observed concentration of 3.4 million pCi/L. Some of the tritium that was previously leached from the activated soil was trapped in the vadose (unsaturated) zone soils directly above the water table after then cap was installed. A portion of this residual tritium was later mobilized into the groundwater during periods of high groundwater table elevations, which can occur following heavy seasonal rainfall. Monitoring results for the past two years indicate that the amount of tritium being released from the vadose zone is decreasing, with tritium concentrations consistently below 100,000 pCi/L. The tritium plume is currently 550 meters long, and is located entirely in the central portion of the BNL site. The plume has not impacted any of the Laboratory's drinking water supply wells. Contaminant transport modeling suggests that the tritium plume will attenuate entirely in the central portion of the BNL site by years 2010-2015. (authors)

54 ENVIRONMENTAL SCIENCES↗

Driving toroidally asymmetric current through the tokamak scrape-off layer. II. Magnetic field structure and spectrum

The structure of the magnetic field perturbations due to nonaxisymmetric field-aligned currents in the tokamak scrape-off layer (SOL) are analytically calculated near the X-point. Paper I [I. Joseph et al., Phys. Plasmas 16, 052510 (2009)] demonstrated that biasing divertor target plates in a toroidally asymmetric fashion can generate an appreciable toroidally asymmetric parallel current density in the SOL along the separatrix. Here, the magnetic field perturbation caused by a SOL current channel of finite width and stepwise constant amplitude at the target plate is derived. Flux expansion amplifies the magnetic perturbation near the X-point, while phase interference causes the SOL amplitude to be reduced at large toroidal mode number. Far enough from the current channel, the magnetic field can be approximated as arising from a surface current near the separatrix with differing amplitudes in the SOL and the divertor leg. The perturbation spectrum and resonant components of this field are computed analytically asymptotically close to the separatrix in magnetic flux coordinates. The size of the stochastic layer due to the applied perturbation that would result without self-consistent plasma shielding is also estimated. If enough resonant field is generated, control of the edge pressure gradient may allow stabilization of edge localized modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

External Magnetic Field Reduction Techniques for the Advanced Stirling Radioisotope Generator

Linear alternators coupled to high efficiency Stirling engines are strong candidates for thermal-to-electric power conversion in space. However, the magnetic field emissions, both AC and DC, of these permanent magnet excited alternators can interfere with sensitive instrumentation onboard a spacecraft. Effective methods to mitigate the AC and DC electromagnetic interference (EMI) from solenoidal type linear alternators (like that used in the Advanced Stirling Convertor) have been developed for potential use in the Advanced Stirling Radioisotope Generator. The methods developed avoid the complexity and extra mass inherent in data extraction from multiple sensors or the use of shielding. This paper discusses these methods, and also provides experimental data obtained during breadboard testing of both AC and DC external magnetic field devices.

Thermoelectric Power Generation↗

AUP First Pre-Series Cryo-Assembly Design Production and Test Overview

New high field and large-aperture quadrupole magnets for the low-beta inner triplets (Q1, Q2, Q3) have been built and tested as part of the high-luminosity upgrade of the Large Hadron Collider (HL-LHC). These new quadrupole magnets are based on Nb3Sn superconducting technology. The US Accelerator Upgrade Project (US-AUP) is producing the Q1 and Q3 Cryo-Assemblies: a pair of ~5 m long magnet structures installed in a stainless-steel helium vessel (Cold Mass) and surrounded by cryostat shields, piping, and a vacuum vessel. In conclusion, this paper gives an overview of the design, production, and the results of the horizontal test of the first pre-series Q1/Q3 Cryo-Assembly.

43 PARTICLE ACCELERATORS↗

Self-Resonant Coil Design for High-frequency High-Power Inductive Wireless Power Transfer

In this paper, the design methodology of a high-frequency, high-power, long-distance inductive wireless power transfer (WPT) is presented. The airgap (d) of a traditional high-power (>1 kW) WPT is limited to a few hundred millimeters, which is almost 1/4th of the coil diameter, D; d ≤ D/4. In this paper, the power transfer distance is significantly increased (d ≥ 1.5D) by adopting a high-frequency magnetic design and GaN-based power electronics. The material and design of the coil and shield are investigated using FEA and tested experimentally. A high frequency 6.78 MHz wireless charging system was built to transfer 1 kW power over 3 m airgap.

Mohammad, Mostak↗

Optimizing Material Selection and Operational Conditions for XHV Systems: Lessons from AISI 1020 and 316L Comparative Studies

In this study, AISI 1020 low-carbon steel is investigated as a cost-effective alternative to SS316 stainless steel for reaching extreme high vacuum (XHV) conditions. After being baked at 400°C, a vacuum chamber made of the low-carbon steel material exhibited an outgassing rate approximately 2000 times smaller than a similar chamber made of stainless steel. Its activation energy for hydrogen diffusion (27 kJ/mol) is less than half that of stainless steel (60.3 kJ/mol), indicating more efficient hydrogen removal during bakeout. MolFlow+ simulations supported the experimental data and demonstrated the importance of system geometry optimization and minimizing stainless steel content for achieving optimal vacuum performance. AISI 1020's magnetic properties, typically considered disadvantageous for accelerator applications, could benefit spin-polarized electron sources by shielding photocathodes from stray fields while simultaneously providing improved vacuum through reduced outgassing. To optimize AISI 1020's performance in XHV systems, practical considerations include pre-baking protocols and careful system design to minimize stainless steel components.

Al-Allaq, Aiman H.↗

The identification of gamma ray induced EAS

Some of the penetrating particles in gamma-induced EAS from Cygnus X-3 observed by a single layer of flash-bulbs under 880 g cm/2 concrete, may be punched through photons rather than muons. An analysis of the shielded flash-tube response detected from EAS is presented. The penetration of the electro-magnetic component through 20 cm of Pb is observed at core distances approx. 10 m.

Blake, P. R.↗

Operational Radiation Protection in Synchrotron Light and Free Electron Laser Facilities

The 3rd generation synchrotron radiation (SR) facilities are storage ring based facilities with many insertion devices and photon beamlines, and have low injection beam power (< few tens of watts), but extremely high stored beam power ({approx} 1 GW). The 4th generation x-ray free electron laser (FEL) facilities are based on an electron Linac with a long undulator and have high injection beam power (a few kW). Due to its electron and photon beam characteristics and modes of operation, storage ring and photon beamlines have unique safety aspects, which are the main subjects of this paper. The shielding design limits, operational modes, and beam losses are first reviewed. Shielding analysis (source terms and methodologies) and interlocked safety systems for storage ring and photon beamlines (including SR and gas bremsstrahlung) are described. Specific safety issues for storage ring top-off injection operation and FEL facilities are discussed. The operational safety program, e.g., operation authorization, commissioning, training, and radiation measurements, for SR facilities is also presented.

43 PARTICLE ACCELERATORS↗

A theory of electrical conductivity, dielectric constant, and electromagnetic interference shielding for lightweight graphene composite foams

This work was driven by the need to understand the electromagnetic interference (EMI) shielding effectiveness (SE) of light weight, flexible, and high performance graphene composite foams, but as EMI SE of a material depends on its electrical conductivity, dielectric permittivity, and magnetic permeability, the investigation of these three properties also became a priority. In this paper, we first present a continuum theory to determine these three electromagnetic properties, and then use the obtained properties to evaluate the EMI SE of the foam. A two-scale composite model is conceived to evaluate these three properties, with the large one being the skeleton-void composite and the small one being the graphene-polymer composite that serves as the skeleton of the foam. To evaluate the properties of the skeleton, the effective-medium approach is taken as the starting point. Subsequently, the effect of an imperfect interface and the contributions of electron tunneling to the interfacial conductivity and Maxwell-Wagner-Sillars polarization mechanism to the dielectric constant are also implemented. The derived skeleton properties are then utilized on the large scale to determine the three properties of the composite foam at a given porosity. Then a uniform plane electromagnetic wave is considered to evaluate the EMI SE of the foam. It is demonstrated that the electrical conductivity, dielectric constant, and EMI SE of the foam calculated from the developed theory are in general agreement with the reported experimental data of graphene/PDMS composite foams. The theory is further proven to be valid for the EMI SE of solid graphene/epoxy and solid carbon nanotube/epoxy nanocomposites. It is also shown that, among the three electromagnetic properties, electrical conductivity has the strongest influence on the EMI shielding effectiveness.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

In Situ MOF Pyrolysis Construction of Hierarchical Porous Co‐Nanoparticles/Carbon Cloth Composites for Enhanced Electromagnetic Wave Shielding and Absorption

The development of high-performance electromagnetic protection materials integrating broadband absorption and effective shielding capabilities is hindered by challenges in simultaneously optimizing multiple electromagnetic properties through conventional material designs. This study pioneers a hierarchical porous Co nanoparticle/carbon cloth (Co/CC) composite via controlled annealing of a Co-MOF precursor on carbon cloth. The Co-MOF served a dual role as both magnetic source and pore-forming agent, enabling in situ generation of uniformly dispersed Co nanoparticles and creation of abundant pores/interfaces on the CC fibers during pyrolysis. This unique architecture synergistically enhanced dielectric loss (via interfacial/dipolar polarization) and magnetic loss (via natural resonance, exchange interactions, and eddy currents), significantly improving impedance matching. The hierarchical pores further functioned as integrated “absorption–reflection” units for efficient electromagnetic energy attenuation. Consequently, the Co/CC composite annealed at 800°C (Co/CC-800) achieves minimum reflection loss (−40.69 dB) and 120% effective absorption bandwidth extension (6.16 GHz) as a filler, and exhibits superior electromagnetic interference shielding effectiveness (46.66 dB) as an integrated component. Significantly, Co/CC-800 demonstrated robust photothermal and electrothermal conversion capabilities, ensuring operational stability in ice-covered and humid harsh environments. This work pioneers a pore-structure-mediated strategy to harmonize dielectric–magnetic synergy, providing a new paradigm for designing advanced multifunctional electromagnetic protection materials.

dielectric‐magnetic synergy↗

Structure and magnetic properties of Co-W clusters produced by inert gas condensation

In this article, inert-gas condensation was used to synthesize Co-W clusters. The formation, structure, and magnetic properties of the clusters were investigated. Sub-10-nm clusters were obtained, and the structures and average sizes were strongly dependent on sputtering power. At low sputtering powers, the clusters were predominantly amorphous, while, at high sputtering power, the clusters were crystalline. X ray diffraction and transmission electron microscopy revealed clusters with hcp structure at high sputtering power. The magnetic properties were dependent on the sputtering power and temperature, with the highest coercivity of 810 Oe at 10 K for high sputtering power.

36 MATERIALS SCIENCE↗

Radiation Damage Analysis of FNSF Components Using McCad and MCNP

The Fusion Energy System Studies Fusion Nuclear Science Facility (FESS-FNSF) concept represents a transitional step between ITER and a commercial fusion power plant. The FNSF is a conceptualized D-T fueled tokamak with 518 MW of fusion power that has been extensively used to explore and optimize design features. The energetic 14.1-MeV neutrons can produce significant localized heating and activations, and can cause damage to plasma-facing components, which can determine maintenance/outage scheduling needs and also impact the lifetime of the device as a whole. This study illustrates a neutronics analysis that was conducted on a 22.5-degree symmetric sector of the FNSF with the goal of understanding the neutron heating and radiation damage that can be characterized by quantifying the displacements per atom (dpa). Concurrently, this study also focused on the development of analysis capabilities by converting a three-dimensional computer-aided design model of the FNSF into MCNP6.2 input using the McCad code. Accordingly, some confirmatory results on tritium production and the tritium breeding ratio (TBR) are provided to support model validation. The results produced by MCNP6.2 simulations showed that the highest heating and damage occurred in the outboard region, which concentrated approximately 290 MW of the total nuclear heating, in contrast to 97 MW within the inboard region. These results are consistent with previous studies that employed earlier versions of the FNSF concept and different modeling approaches. Furthermore, this study also provides additional details on neutron wall loading, as well as total heating from neutrons and gammas, results which show the total heating of the device (16 sectors) is approximately 477.83 ± 0.80% MW, indicating a neutron energy multiplication factor of 1.15. Additionally, the capability to calculate hydrogen and helium production, as well as dpa, is illustrated. Finally, the neutronics effects of using alternative materials to tungsten carbide were evaluated for the vacuum vessel, low-temperature shield, and structural ring components, which showed that compounds like YH 2 , Mg(BH 4 ) 2 , and ZrH 2 could reduce the total heating on the magnet and also reduce the TBR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The magnetic moment of Venus - Venera-4 measurements reinterpreted

Venera-4 magnetic-field measurements made during that spacecraft's descent through the atmosphere of Venus are reexamined using three models for the interaction of the solar-wind with the planet. The first model assumes the existence of just the interplanetary and planetary magnetic fields; the second admits the presence of a magnetosheath and a current layer, but assumes that the magnetosheath field is spatially uniform between the planet and the bow shock; the third assumes shielding of the planetary field from the magnetosheath field by a current layer. All three models are found to yield a strong altitude dependence for the magnitude of the planetary field, suggesting that the intrinsic magnetic dipole moment of Venus may exceed that of both Mars and Mercury. It is concluded that a Venusian surface field of 30 gammas is a plausible interpretation of the Venera-4 measurements.-

Russell, C. T.↗

One Structure, Two Elements—LuGe 2 Superconductor vs Ordinary Metallic Conductor LuSn 2 . A Case Study on How Site-Selective Germanium for Tin Atom Substitution Leads to Modulating of the Charge Distribution

The substitution of chemically similar elements in a given crystal structure is an effective way to enhance physical properties, but the understanding on such improvements is usually impeded because the substitutions are random, and the roles of the different atoms cannot be distinguished by crystallographic symmetry. Herein, we provide a detailed crystallographic analysis and property measurements for the continuous solid solutions LuGe x Sn 2–x (0 < x < 2). The results show that there is no apparent change of the global symmetry, with the end-members LuGe 2 and LuSn 2 , as well as the intermediate LuGe x Sn 2–x compositions adopting the ZrSi 2 type structure (space group Cmcm, Pearson index oC12). Yet, the refinements of the crystal structures from single-crystal X-ray diffraction data show that Ge–Sn atom substitutions are not random, but occur preferentially at the zig-zag chain. The patterned distribution of two group 14 elements leads to a significant variation in chemical bonding and charge ordering within the other structural fragment, the 2D square nets, thereby resulting in tuned electron transport. The enhancement is greater than the typical Bloch-Gruneisen model, and more akin to the parallel-resistor model. Magnetization measurements on single crystals show bulk superconductivity in all LuGe x Sn 2–x samples with shielding fractions as high as 90%. Specific heat data confirm the effect to originate from residual metallic tin in the material, indicating that Sn atom substitutions in the 2D square nets cause disruptions of the hypervalent bonding and local anisotropy, which ultimately leads to vanishing of the superconducting state in the end-member LuGe 2 . This work sheds light on how the complexity in chemical interactions by two different carbon congeners leads to changes in the physical properties and how they can be correlated with the induced charge distribution. Furthermore, these studies also provide a general approach to modulation of charge density, and thus, of emerging physical properties in other classes of intermetallic systems based on the main-group elements of groups 13 to 15.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

67 Zn Solid-State NMR Spectroscopy of {[Tp But,Me ]Zn(OH 2 )}[HOB(C 6 F 5 ) 3 ]. The Importance of the Anion [HOB(C 6 F 5 ) 3 ] -

We have utilized solid-state 67 Zn NMR spectroscopy as a means to characterize one of the few examples of water bound to mononuclear tetrahedral Zn 2 + : {[Tp But,Me ]Zn(OH 2 )}[HOB(C 6 F 5 ) 3 ]. The measured quadrupole coupling (Cq) constant is 4.3 MHz with an asymmetry parameter of ηq of 0.6. Likewise, due to the small value of Cq, anisotropic shielding also contributed to the observed 67 Zn NMR lineshape. As expected, the computed values of the magnetic resonance parameters depend critically on the nature of the anion. The predicted value of Cq for {[Tp But,Me ]Zn(OH 2 )}[HOB(C 6 F 5 ) 3 ] is -4.88 MHz. We discuss the results of these calculations in terms of the nature of the anion, the local electrostatics, and its subsequent hydrogen bonding to [Tp But,Me ]Zn(OH 2 ) + .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Planck intermediate results. XIX. An overview of the polarized thermal emission from Galactic dust

This paper presents an overview of the polarized sky as seen by Planck HFI at 353 GHz, which is the most sensitive Planck channel for dust polarization. We construct and analyse maps of dust polarization fraction and polarization angle at 1° resolution, taking into account noise bias and possible systematic effects. The sensitivity of the Planck HFI polarization measurements allows for the first time a mapping of Galactic dust polarized emission on large scales, including low column density regions. We find that the maximum observed dust polarization fraction is high ( p max = 19.8%), in particular in some regions of moderate hydrogen column density ( N H < 2 × 10 21 cm -2 ). The polarization fraction displays a large scatter at N H below a few 10 21 cm -2 . There is a general decrease in the dust polarization fraction with increasing column density above N H ≃ 1 × 10 21 cm -2 and in particular a sharp drop above N H ≃ 1.5 × 10 22 cm -2 . We characterize the spatial structure of the polarization angle using the angle dispersion function. We find that the polarization angle is ordered over extended areas of several square degrees, separated by filamentary structures of high angle dispersion function. These appear as interfaces where the sky projection of the magnetic field changes abruptly without variations in the column density. The polarization fraction is found to be anti-correlated with the dispersion of polarization angles. These results suggest that, at the resolution of 1&deg;, depolarization is due mainly to fluctuations in the magnetic field orientation along the line of sight, rather than to the loss of grain alignment in shielded regions. We also compare the polarization of thermal dust emission with that of synchrotron measured with Planck , low-frequency radio data, and Faraday rotation measurements toward extragalactic sources. These components bear resemblance along the Galactic plane and in some regions such as the Fan and North Polar Spur regions. The poor match observed in other regions shows, however, that dust, cosmic-ray electrons, and thermal electrons generally sample different parts of the line of sight.

79 ASTRONOMY AND ASTROPHYSICS↗

First results from the implementation of the ITER diagnostic residual gas analyzer prototype at Wendelstein 7-X

Fusion reactors and long pulse fusion experiments heavily depend on a continuous fuel cycle, which requires detailed monitoring of exhaust gases. We have used a diagnostic residual gas analyzer (DRGA) built as a prototype for ITER and integrated it on the most advanced stellarator fusion experiment, Wendelstein 7-X (W7-X). The DRGA was equipped with a sampling tube and assessed for gas time of flight sample response, effects of magnetic field on gas detection and practical aspects of use in a state of the art fusion environment. The setup was successfully commissioned and operated and was used to observe the gas composition of W7-X exhaust gases. The measured time of flight gas response was found to be in the order of a second for a 7 m sample tube. High values of magnetic field were found to affect the partial pressure readings of the DRGA and suggest that additional shielding is necessary in future experimental campaigns.

47 OTHER INSTRUMENTATION↗

ACCELERATING FUSION REACTOR NEUTRONICS MODELING BY AUTOMATIC COUPLING OF HYBRID MONTE CARLO/DETERMINISTIC TRANSPORT ON CAD GEOMETRY

Detailed radiation transport calculations are necessary for many aspects of the design of fusion energy systems (FES) such as ensuring occupational safety, assessing the activation of system components for waste disposal, and maintaining cryogenic temperatures within superconducting magnets. Hybrid Monte Carlo (MC)/deterministic techniques are necessary for this analysis because FES are large, heavily shielded, and contain streaming paths that can only be resolved with MC. The tremendous complexity of FES necessitates the use of CAD geometry for design and analysis. Previous ITER analysis has required the translation of CAD geometry to MCNP5 form in order to use the AutomateD VAriaNce reducTion Generator (ADVANTG) for hybrid MC/deterministic transport. In this work, ADVANTG was modified to support CAD geometry, allowing hybrid (MC)/deterministic transport to be done automatically and eliminating the need for this translation step. This was done by adding a new ray tracing routine to ADVANTG for CAD geometries using the Direct Accelerated Geometry Monte Carlo (DAGMC) software library. This new capability is demonstrated with a prompt dose rate calculation for an ITER computational benchmark problem using both the Consistent Adjoint Driven Importance Sampling (CADIS) method an the Forward Weighted (FW)-CADIS method. The variance reduction parameters produced by ADVANTG are shown to be the same using CAD geometry and standard MCNP5 geometry. Significant speedups were observed for both neutrons (as high as a factor of 7.1) and photons (as high as a factor of 59.6).

Biondo, Elliott D↗