Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lubricants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Plasma-sprayed, self-lubricating coatings for use from cryogenic temperatures to 870 deg C (1600 deg F)

A plasma-sprayed coating is described with good lubricating properties over a wide temperature range. The coating, designated NASA LUBE PS101, contains silver, nichrome, calcium fluoride, and an oxidation protective glass. Oscillating tests were conducted of self-aligning, plain cylindrical bearings, in which the bore was lined with 0.025 cm (0.010 in.) thick coatings of PS101; these were conducted at a radial load of 3.5 x 10 to the 7th power N/sq m (5000 psi) in nitrogen gas at -107 C (-160 F), in vacuum at room temperature, and in air from room temperature to 870 C (1600 F). Friction coefficients were less than 0.25 in all cases and wear rates were low. The coating is not brittle, and it has adequate oxidation resistance in air to at least 870 C.

Sliney, H. E.↗
NASA NTRS1974

Ferrographic analysis of wear debris from boundary lubrication experiments with a five ring polyphenyl ether

The types of wear particles generated by a five-ring polyphenyl ether in boundary lubrication experiments in various atmospheres were determined by ferrographic analysis. The types of wear particles observed included: cylindrical or rock-like organo-metallic debris, adhesive and cutting wear particles, and some spherical debris. Interpretations as to the mechanism of generation of the various types of particles are presented.

Jones, W. R., Jr.↗
NASA NTRS1974

The viscous lubrication of rolling and sliding rigid cylinders

The viscous lubrication of rolling and sliding cylinders is studied both independently and with the aid of much of the previous work done by other investigators. Building upon the specialized results of others, a problem formulation is obtained which encompasses the general viscous fluid as well as the linear viscous fluid. A uniform solution technique is derived which is adequate for the general problem formulation. Results obtained for three special classes of viscosity functions are presented.

Carlson, S. F.↗
NASA NTRS1975

Measurement of viscosity and elasticity of lubricants at high pressures

The oscillating quartz crystal viscometer has been used to investigate possible viscoelastic behavior in synthetic lubricating fluids and to obtain viscosity-pressure-temperature data for these fluids at temperatures to 300 F and pressures to 40,000 psig. The effect of pressure and temperature on the density of the test fluids was measured concurrently with the viscosity measurements. Viscoelastic behavior of one fluid, di-(2-ethylhexyl) sebacate, was observed over a range of pressures. These data were used to compute the reduced shear elastic (storage) modulus and reduced loss modulus for this fluid at atmospheric pressure and 100 F as functions of reduced frequency.

Rein, R. G., Jr.↗
NASA NTRS1975

Boundary lubrication of formulated C-ethers in air to 300 C

Six C-ether formulations (containing organic acid and phosphorus ester additives) were tested in dry (less than 100 ppm H2O) and moist air (relative humidity 50 percent at 25 C) and temperatures from 25 to 300 C, in order to determine the boundary lubricating characteristics and to compare these results to those obtained with a fully formulated Type II ester and the unformulated C-ether base fluid. The apparatus, procedures and detailed results of the test are described. Friction and wear measurements were made on CVM M-50 steel under 1 kg load and 17 meter per minute (100 rpm) surface speed conditions, for a duration of 25 minutes. In general, the C-ether formulations exhibited higher friction coefficients than the ester from 150 to 300 C and similar or lower values from 25 to 150 C, furthermore, in most test conditions the C-ether base fluid and the six C-ether formulations yielded lower wear than the ester. Possible applications in the aerospace industry are mentioned.

Jones, W. R., Jr.↗
NASA NTRS1975

Friction differences between aliphatic and aromatic structures in lubrication of titanium

Sliding friction experiments were conducted with a titanium (0001) single crystal surface with various adsorbed aliphatic and aromatic compounds containing the same number of carbon atoms. An Auger emission spectroscopy analysis was used to monitor the presence of the organic lubricating compounds. Results of the investigation indicate that hexane and benzene give the same friction coefficients over a range of loads. At light loads the friction decreased with an increase in the halogen atom size where the halogens chlorine, bromine, and iodine are incorporated into the benzene molecular structure. The aliphatic compounds chlorohexane and bromohexane exhibited lower friction coefficients than the aromatic structures chlorobenzene and bromobenzene.

Buckley, D. H.↗
NASA NTRS1976

Analysis of the gas-lubricated flat-sector-pad thrust bearing

A flat sector-shaped pad geometry for a gas-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. It is shown that maximum load capacity is achieved when the pad is tilted so as to create uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves, and a comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. I - Theoretical formulation

The analysis of an isothermal elastohydrodynamic lubrication (EHL) point contact was evaluated numerically. This required the simultaneous solution of the elasticity and Reynolds equations. In the elasticity analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each element. In the numerical analysis of the Reynolds' equation a phi analysis where phi is equal to the pressure times the film thickness to the 3/2 power is used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗
NASA NTRS1977

Infrared temperature maps of EHD lubrication

Technique uses an infrared detector with two specially selected infrared filters, in separately mapping the contact-surface temperature and average oil-film temperature in an elastohydrodynamic conjunction. Apparatus includes conventional four-ball bearing tester and temperature controlled lubricant system.

Sanborn, D. M.↗
NASA NTRS1978

Determining minimum lubrication film for machine parts

Formula predicts minimum film thickness required for fully-flooded ball bearings, gears, and cams. Formula is result of study to determine complete theoretical solution of isothermal elasto-hydrodynamic lubrication of fully-flooded elliptical contacts.

Hamrock, B. J.↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. III: Fully flooded results

The influence of the ellipticity parameter and the dimensionless speed U, load W, and material G parameters on minimum film thickness was investigated. The ellipticity parameter k was varied from 1 (a ball-on-plate configuration) to 8 (a configuration approaching a line contact). The dimensionless speed parameter was varied over a range of nearly two orders of magnitude. And the dimensionless load parameter was varied over a range of one order of magnitude. Conditions corresponding to the use of solid materials of bronze, steel, and silicon nitride and lubricants of paraffinic and naphthenic mineral oils were considered in obtaining the exponent on the dimensionless material parameter.

Hamrock, B. J.↗
NASA NTRS1977

Design charts for arbitrarily pivoted, liquid-lubricated flat-sector-pad thrust bearing

A flat, sector-shaped geometry for a liquid-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. Results are presented in design charts that enable a direct approach to the design of point- and line-pivoted, tilting pad bearings. A comparison is made with the Mitchell bearing approximation and it is found that this approximation always overestimates load capacity.

Etsion, I.↗
NASA NTRS1977

Elastohydrodynamic lubrication of elliptical contacts for materials of low elastic modulus. 1: Fully flooded conjunction

Elastohydrodynamic lubrication concepts of conjunctions of elliptical form are applied to materials of low elastic modulus. The influence of the ellipticity parameter and the dimensionless speed, load, and material parameters on minimum film thickness for these materials has been investigated. The ellipticity parameter was varied from a ball on plate configuration to a configuration approaching a line contact. The dimensionless speed and load parameters were varied by 1 order of magnitude. Seventeen different cases were used to generate minimum and central film thickness relations. Contour plots are presented that illustrate the pressure distribution and film thickness in the conjunction.

Hamrock, B. J.↗
NASA NTRS1977

Study of Lubricant Jet Flow Phenomena in Spur Gears: Out of Mesh Condition

Oil jet lubrication on the disengaging side of a gear mesh was analyzed. Results of the analysis were computerized and used to determine the oil jet impingement depth for several gear ratios and oil jet to pitch line velocity ratios. A gear test rig using high speed photography was used to experimentally determine the oil jet impingement depth on the disengaging side of mesh. Impingement depth reached a maximum at gear ratio near 1.5 where chopping by the leading gear tooth limited impingement depth. The pinion impingement depth is zero above a gear ratio of 1.172 for a jet velocity to pitch time velocity ration of 1.0 and is similar for other velocity ratios. The impingement depth for gear and pinion are equal and approximately one half the maximum at a gear ration of 7.0.

Townsend, D. P.↗
NASA NTRS1976

An accurate solution of the gas lubricated, flat sector thrust bearing

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗
NASA NTRS1978

Effect of thermal exposure on lubricating properties of polyimide films and polyimide-bonded graphite fluoride films

The effect of thermal exposure on the weight loss, adherence, friction, and wear properties of polyimide films and polyimide bonded graphite fluoride films was investigated. Films bonded to 304 stainless steel or 440C-HT steel were thermally exposed at temperatures of 315 ,345, 370, or 400 C for 100 hours or more and then evaluated, using a pin-on-disk machine, at temperatures of 25, 315, or 345 C in atmospheres of dry or moist air. Polyimide films were brittle after thermal exposure. Polyimide bonded graphite fluoride films had adherence and gave low friction and wear results; thus, they appear to be good candidates for solid lubrication applications where long thermal soaks are prevalent.

Fusaro, R. L.↗