Coupled nongray radiating flows about long blunt bodies
Time asymptotic solutions for hypervelocity blunt body flow field with coupled nongray radiation, treating shock as discrete surface
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Time asymptotic solutions for hypervelocity blunt body flow field with coupled nongray radiation, treating shock as discrete surface
Nonreacting and equilibrium chemically reacting gas turbulent boundary layer flows through hypervelocity nozzles, comparing calculation with experiment
The analysis of hypervelocity impact of particles on a detector in space, with flow and shock penetration through fluid, plastic, and elastic zones was studied. The original paper and computer program on this topic is presented. Improvements in the program for the study of the formation of a cone of debris are discussed. The truncated apex of the cone is at the hole formed by the penetration of an initially spherical rock through a thin plate. A solution for the penetration of the thin plate was sought.
A number of tests are required to evaluate both multilayer high performance insulation samples and the materials that comprise them. Some of the techniques and tests being employed for these evaluations and some of the results obtained from thermal conductivity tests, outgassing studies, effect of pressure on layer density tests, hypervelocity impact tests, and a multilayer high performance insulation ambient storage program at the Kennedy Space Center are presented.
The results of work on the McDonnell Douglas delta wing orbiter are summarized and compared to other data and theories where applicable. The tests were conducted in the continuous hypersonic Tunnel B at Mach 8 and in the hypervelocity hotshot Tunnel F at Mach 10.5. Photographic data are used to illustrate the regions of peak heating on the lee-side and to show the vortical nature of the flow. Windward centerline data include measurements of shock angle, surface pressure, flow field pitot pressure and total temperature, and heat transfer rate coefficient distributions. Shock angles, surface pressures, and local Mach number distributions are compared with tangent cone theory over an angle of attack range from 10 to 60 deg. The measured heat transfer rate coefficient distributions are compared to both laminar and turbulent theories and boundary layer transition data are compared to the McDonnell Douglas criteria.
Heat transfer tests for two delta wing configurations were conducted in the hypervelocity wind tunnel. The 24-inch long models were tested at a Mach number of approximately 10.5 and at angles of attack of 20, 40, and 60 degrees over a length Reynolds number range from 5 million to 23 million on 4 May to 4 June 1971. Heat transfer results were obtained from model surface heat gage measurements and thermographic phosphor paint.
Heat transfer tests for the delta wing orbiter were conducted in a hypervelocity wind tunnel. A 1.1 percent scale model was tested at a Mach number of approximately 10.5 over an angle of attack range from 10 to 60 degrees over a length Reynolds number range from 5 times 10 to the 6th power to 24 times 10 to the 6th power. Heat transfer results were obtained from model surface heat gage measurements and thermographic phosphor paint. Limited pressure measurements were obtained.
Sections C and E of the unpainted, polished aluminum tubing from the strut of the radar altimeter and Doppler velocity sensor were examined in a transmission electron microscope for micrometeorite damage and ion bombardment. Both sections were contaminated and eroded on one side; it is suggested that these conditions were caused by sandblasting by lunar dust and retrorocket plume contamination during Surveyor 3 landing. Microcraters of different configurations were found on the bright sides of the tubes. Several degrees of violence were involved in the formation of the craters, and the particle size could be responsible for some differences. All micropits found were on the bright areas and data indicate 0.2 hypervelocity impact/sq cm and 2/sq cm for other types of craters. The greatest degree of damage resulted from particle impact and was limited to a maximum depth of 2 microns.
The television housing and a section of the strut of the radar altimeter and Doppler velocity sensor were examined optically and with a scanning electron microscope for particulate impacts. The white surface of the camera was discolored during the months the Surveyor 3 was on the moon; however, most of the craters must have occurred as a result of lunar dust sandblasted by the LM exhaust. The polished section of the strut exhibits contamination which appears brown and seems to be partially composed of crystals. Electron microscopic analysis of the strut section indicated no craters of hypervelocity impact origin, confirmed pitting density results of the optical scans, and indicated that material in the craters is of lunar origin. No meteorite impacts larger than 25 microns were detected on the tubing section.
A shock-swallowing, self-aspirating, local total enthalpy probe has been evaluated in a low density nonequilibrium, hypervelocity airstream. The probe, which incorporated an air gap to separate the internal and external cooling passages, was tested in an electric archeated wind tunnel at an average Mach number of 11.7 and an average Reynolds number per meter of 57,000. The free stream enthalpy probe data are compared with bulk calorimeter measurements of total enthalpy at the beginning of the gas expansion and with local total enthalpy inferred from a theoretical nonequilibrium gas expansion model by using free stream velocity measurements obtained from a mass flow probe. The three techniques are in relative agreement at the lower enthalpies. However, at the higher enthalpies, the enthalpy probe data lie considerably below the other data. This low data may be caused by the chemical and vibrational energy frozen in the flow not being sensed by the probe. Other problems associated with the shock-swallowing total enthalpy probe are discussed, and recommendations for improving the probe performance are presented.
Studies directed toward the development of a computer program describing the penetration of a thin aluminum plate by a quartz sphere are reported. The aluminum simulates a bumper plate for micrometeoroids. The ablation of a rock sphere by penetrating a stack of paper sheets is described, and an equation for losses near the surface of the sphere is derived. The expansions of aluminum plasma sphere with initial energies of 44.45, 20.8, and 7.136 eV are investigated, including shock compression during penetration and adiabatic expansion. The equations of state were derived for aluminum and quartz, as well as one of the Mie-Grunesen type. A technique to determine momentum at the bottom surface of the thin plate, and the energy for hypervelocity separation of fragments of the aluminum plate are also considered.
Surface pressures, heat-transfer rates, and transition locations for a sharp cone (whose semivertex angle is 12 deg) were obtained in a hypervelocity wind tunnel at a free-stream Mach number of 12 and a free-stream Re/ft range of 3,000,000 to 6,000,000. The effects of injecting either methane, nitrogen, or Freon-22 (at rates up to 2.1% of free-stream rate) were studied for a uniform injection-distribution and for a variable injection-distribution. Gaseous injection had little effect on the surface pressure measurements. For a given mass injection distribution, the laminar region heat-transfer decreases as the injection rate increases or as the molecular weight of the injectant decreases. For a given mass-injection rate (integrated over the surface of the entire cone), the transition location and heat-transfer rates were sensitive to the injection distribution. The transition Reynolds numbers were significantly greater when the local injection rate was constant over the surface of the cone.
A brief review is given of blast and detonation wave phenomena and some of their uses in war and peace. It is concluded that great strides have been made over the last three decades toward the physical understanding, the analytical-numerical solution, and the measurement of dynamic and thermodynamic quantities, also taking into consideration severe environments and extremely short durations. Questions of internal ballistics are discussed together with hypervelocity launchers and shock tubes, collapsing cylindrical drivers, spherical implosions, explosive weapons, dynamic response, and equation of state data.
The entropy associated with the thermodynamic states produced by hypervelocity meteoroid impacts at various velocities are calculated for a series of lunar rocks and minerals and compared with the entropy values required for melting and vaporization. Taking into account shock-induced phase changes in the silicates, we calculate that iron meteorites impacting at speeds varying from 4 to 6 km/sec will produce shock melting in quartz, plagioclase, olivine, and pyroxene. Although calculated with less certainty, impact speeds required for incipient vaporization vary from 7 to 11 km/sec for the range of minerals going from quartz to periclase for aluminum (silicate-like) projectiles. The impact velocities, which are required to induce melting in a soil, are calculated to be in the range of 3 to 4 km/sec, provided thermal equilibrium is achieved in the shock state.
Results from laboratory studies of hypervelocity impact against crystalline rocks, combined with estimates of the micrometeoroid flux at the lunar surface, provide a basis for calculating abrasion rates and survival times before catastrophic rupture of rocks on the lunar surface. The surface residence times observed for lunar rocks of the order of 10 m.y. (derived from the track densities of iron group nuclei) restrict the mass range of impacting particles of interest to masses less than about 1.01 gram. Extrapolation downward to smaller masses following flux distributions suggested by early satellite data and photographic meteor observations leads to absurd rates of abrasion. Consistent with the observed crater populations on the lunar rocks and with the Pegasus, Explorer, and Pioneer satellite data, the slope of the mass-flux distribution must decrease markedly for masses below 1 to .1 microgram.
The results of a continuing program to develop an explosively driven 2-stage hypervelocity launcher capable of achieving velocities between 15 and 20 km/sec are described. Previous efforts had identified incomplete barrel collapse as a limiting factor in launcher performance. Correlation of experimental and computational results obtained in the present study indicate that boundary-layer gases within the barrel act to prevent complete closure. Simplified calculations suggest that in-contact explosives may have insufficient energy densities to collapse the barrel against a developed boundary layer. Higher energy densities, sufficient to produce complete closure, were obtained with the use of steel flyer plates accelerated by a phased explosive lens. However, when flat flyer plates were impacted on the barrel, the sides of the barrel were observed to rupture and leak gas prior to barrel closure. A promising solution to this problem (untested) is to produce a symmetrical collapse with a cylindrical tube around the barrel.
A piston assembly is described for use in a hypervelocity gun comprising a forward cylindrical section longitudinally spaced from a rearward cylindrical section by an intermediate section. The intermediate section is longitudinally collapsible when subjected to a predetermined force, to allow the distance between the forward and rearward sections to be suddenly reduced.
A new configuration of a coaxial plasma accelerator with self-energized magnetic compressor coil attached is described. It is shown that the circuit may be treated theoretically by analyzing an equivalent circuit mesh. The results obtained from the theoretical analysis are shown to compare favorably with the results measured experimentally. Using this accelerator configuration, glass beads of 125-micron diameter were accelerated to velocities as high as 11 km/sec, while 700-micron-diam glass beads were accelerated to velocities as high as 5 km/sec. The velocities are within the hypervelocity regime of meteroids.