Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GaGe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Effects of wing/elevon gap sealing flapper doors on orbiter elevon effectiveness of model 16-0 in the NAAL 7.75 by 11 foot continuous flow wind tunnel (OA119A)

Space shuttle orbiter elevon effectiveness was measured with the 6 inch elevon/elevon and elevon/fuselage gaps and various configurations of wing/elevon upper hingeline gap sealing flapper doors. The elevon configuration parametric variations consisted of sealing the lower hingeline to prevent flow-through and testing a long chord flapper door, a short chord flapper door, no flapper door (elevon/wing gap upper hingeline completely open), and a completely sealed elevon at elevon deflections from +20 deg to -40 deg. Preliminary data analysis indicates loss of elevon effectiveness at deflections more negative than -20 deg, and little or no effect of flapper door configuration on elevon effectiveness. Flow visualization photographs taken at alpha = 15 deg for two flapper door configurations substantiated the force data results. Aerodynamic force and moment data were measured in the body axis by a 2.5 inch task type internal strain gage balance. The model was sting supported through the base region with a nominal angle of attack range of -10 deg less than or equal to alpha less than or equal to 24 deg at a model angle of sideslip of Beta equal to 0 deg.

Mennell, R.↗
NASA NTRS1975

The effect of ring distortions on buckling of blunt conical shells

A rigorous analytical study of cones stiffened by many thin-gage, open-section rings is presented. The results are compared with data previously obtained from uniform pressure tests of the Viking mission flight aeroshell and of the Viking structural prototype aeroshells. A conventional analysis, in which the rings are modeled as discrete rigid cross sections, is shown to lead to large, unconservative strength predictions. A more sophisticated technique of modeling the rings as shell branches leads to much more realistic strength predictions and more accurately predicts the failure modes. It is also shown that if a small initial imperfection proportional to the shape of the buckling mode is assumed, the critical buckling modes from analysis and test are in agreement. However, the reduction in buckling strength from the perfect-shell predictions is small.

Heard, W. L., Jr.↗
NASA NTRS1974

Thermoelectric Outer Planets Spacecraft (TOPS) electronic packaging and cabling development summary report

Electronic packaging and cabling activities performed in support of the Thermoelectric Outer Planets Spacecraft (TOPS) Advanced Systems Technology (AST) project are detailed. It describes new electronic compartment, electronic assembly, and module concepts, and a new high-density, planar interconnection technique called discrete multilayer (DML). Development and qualification of high density cabling techniques, using small gage wire and microminiature connectors, are also reported.

Dawe, R. H.↗
NASA NTRS1975

Results of investigation IA110 on a 0.015-scale integrated configuration of the space shuttle vehicle in the arc 9 x 7 supersonic wind tunnel using models 67-TS and 49-0

An 0.015-scale space shuttle vehicle model was tested to investigate Orbiter wind bending, elevon panel loads, and elevon effectiveness. Mach numbers from 1.5 through 2.5 were investigated. Angles of attack and sideslip were varied from -8 degrees through +8 degrees. Post test analysis of raw wind tunnel data indicated a zero shift had occured in the wing bending and torsional gages during the test. The mechanism by which this shift occurred was not determined. Therefore, all the wind root bending and torsional moment data is suspect.

Chee, E.↗
NASA NTRS1975

Design, fabrication and test of lightweight shell structure

A cylindrical shell structure 3.66 m (144 in.) high by 4.57 m (180 in.) diameter was designed using a wide variety of materials and structural concepts to withstand design ultimate combined loading 1225.8 N/cm (700 lb/in.) axial compression and 245.2 N/cm (140 lb/in.) torsion. The overall cylinder geometry and design loading are representative of that expected on a high performance space tug vehicle. The relatively low design load level results in designs that use thin gage metals and fibrous-composite laminates. Fabrication and structural tests of small panels and components representative of many of the candidate designs served to demonstrate proposed fabrication techniques and to verify design and analysis methods. Three of the designs evaluated, honeycomb sandwich with aluminum faceskins, honeycomb sandwich with graphite/epoxy faceskins, and aluminum truss with fiber-glass meteoroid protection layers, were selected for further evaluation.

Lager, J. R.↗
NASA NTRS1975

Results of an investigation elevon hinge moments and dual panel elevon effectiveness using an .0405-scale model (16-0) of the configuration 140C space shuttle orbiter in the Rockwell International NAAL low speed wind tunnel (OA119B)

Experimental aerodynamic investigations were conducted on a sting mounted .0405-scale representation of the 140C outer mold line space shuttle orbiter in a 7.75 x 11.00 foot low speed wind tunnel during the time period from August 22, 1974 to September 6, 1974. The primary test objectives were to define dual panel elevon/aileron effectiveness and to investigate elevon hinge-moments for the 140C orbiter configuration with wing/elevon upper hingeline sealing flapper doors. The elevon parametric variations, consisting of the basic elevons with 6 inch gaps and flapper doors, elevons with no flapper doors and completely open upper hingeline gap, and an entirely sealed solid elevon, were tested with elevon deflections from +20 to -35 deg at various aileron deflections. Aerodynamic force and moment data were measured in the body axis system by a 2.5 inch task type internal strain gage balance.

Mennell, R. C.↗
NASA NTRS1975

A study of application of remote sensing to river forecasting. Volume 1: Executive summary

A project is described whose goal was to define, implement and evaluate a pilot demonstration test to show the practicability of applying remotely sensed data to operational river forecasting in gaged or previously ungaged watersheds. A secondary objective was to provide NASA with documentation describing the computer programs that comprise the streamflow forecasting simulation model used. A computer-based simulation model was adapted to a streamflow forecasting application and implemented in an IBM System/360 Model 44 computer, operating in a dedicated mode, with operator interactive control through a Model 2250 keyboard/graphic CRT terminal. The test site whose hydrologic behavior was simulated is a small basin (365 square kilometers) designated Town Creek near Geraldine, Alabama.

Source record↗
NASA NTRS1975

Stresses in a webbed ball

An experimental stress analysis was undertaken to evaluate stresses within cylindrically hollow reinforced webbed bearing balls proportioned for a 50 percent mass reduction. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models, which were statically loaded in various orientations. Results are reported for 127 mm (5 in.) outside diameter balls under 44,500 N (10,000 lb) loads. Similitude considerations permit these results to be applied to calculations of stresses in actual size drilled bearing balls proportioned to these mass reductions.

Nypan, L. J.↗
NASA NTRS1975

Prediction and verification of creep behavior in metallic materials and components for the space shuttle thermal protection system. Volume 2: Phase 2 subsize panel cyclic creep predictions

A method for predicting permanent cyclic creep deflections in stiffened panel structures was developed. The resulting computer program may be applied to either the time-hardening or strain-hardening theories of creep accumulation. Iterative techniques were used to determine structural rotations, creep strains, and stresses as a function of time. Deflections were determined by numerical integration of structural rotations along the panel length. The analytical approach was developed for analyzing thin-gage entry vehicle metallic-thermal-protection system panels subjected to cyclic bending loads at high temperatures, but may be applied to any panel subjected to bending loads. Predicted panel creep deflections were compared with results from cyclic tests of subsize corrugation and rib-stiffened panels. Empirical equations were developed for each material based on correlation with tensile cyclic creep data and both the subsize panels and tensile specimens were fabricated from the same sheet material. For Vol. 1, see N75-21431.

Cramer, B. A.↗
NASA NTRS1975

ASRDI oxygen technology survey. Volume 8: Pressure measurement

Pressure transducers and their current uses with gaseous or liquid oxygen are reviewed. All transducer types such as strain gage, capacitance, potentiometric, piezoelectric, etc., are included. Topics covered include: cryogenic pressure measurement; material compatibility with gaseous and liquid oxygen; cleaning procedures; pressure tap connections; transducer types and descriptions; and calibration techniques.

Arvidson, J. M.↗
NASA NTRS1975

Lamination residual stresses in fiber composites

An experimental investigation was conducted to determine the magnitude of lamination residual stresses in angle-ply composites and to evaluate their effects on composite structural integrity. The materials investigated were boron/epoxy, boron/polyimide, graphite/low modulus epoxy, graphite/high modulus epoxy, graphite/polyimide and s-glass/epoxy. These materials were fully characterized. Static properties of laminates were also determined. Experimental techniques using embedded strain gages were developed and used to measure residual strains during curing. The extent of relaxation of lamination residual stresses was investigated. It was concluded that the degree of such relaxation is low. The behavior of angle-ply laminates subjected to thermal cycling, tensile load cycling, and combined thermal cycling with tensile load was investigated. In most cases these cycling programs did not have any measurable influence on residual strength and stiffness of the laminates. In the tensile load cycling tests, the graphite/polyimide shows the highest endurance with 10 million cycle runouts at loads up to 90 percent of the static strength.

Daniel, I. M.↗
NASA NTRS1975

The relationship between reliability and bonding techniques in hybrid microcircuits

Differential thermal expansion was shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. It is shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis was conducted of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses. It was experimentally observed that the stresses in more compliant bonding systems such as soft lead tin and indium solders are significantly lower than those in hard solder and epoxy systems. The marked dependence upon heating and cooling rate was proven to be a determining factor in the prediction of failure solder systems. It was found that the harder or higher melting solders are less susceptible to thermal cycling effects but that they are more likely to fail during initial processing operations. Strain gage techniques were used to determine thermally induced expansion stresses of the capacitors and the alumina substrates. The compliance of the different bonding mediums was determined. From the data obtained, several recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.

Caruso, S. V.↗
NASA NTRS1975

S192 multispectral scanner channel 13 electromechanical noise investigation ECP-166

A review is presented of all data on the multispectral scanner having to do with low frequency noise. The noise is component-induced, either mechanical or electrical or a combination of both. To assist in understanding the source of the noise, several dynamic analyses both structural and electrical were made and are reported. A review is presented of structural resonance test data obtained with the use of an accelerometer and strain gage sensors. Results of an analysis of the natural frequencies of the Dewar leads is included along with an analysis of the S192 cooler and its supporting structure. Other topics discussed include electronic stability of the forward signal, automatic gain control, and the offset control feedback loops as well as the preamplifier which utilized on integrator feedback circuit.

Koumjian, H.↗
NASA NTRS1975

Twenty and thirty GHz millimeter wave experiments with the ATS-6 satellite

The ATS-6 millimeter wave experiment, provided the first direct measurements of 20 and 30 GHz earth-space links from an orbiting satellite. Studies at eleven locations in the continental United States were directed at an evaluation of rain attenuation effects, scintillations, depolarization, site diversity, coherence bandwidth, and analog and digital communications techniques. In addition to direct measurements on the 20 and 30 GHz links, methods of attenuation prediction with radars, rain gages, and radiometers were developed and compared with the directly measured attenuation. Initial data results of the ATS-6 millimeter wave experiment from the major participating organizations are presented.

Ippolito, L. J.↗
NASA NTRS1975

Prediction and verification of creep behavior in metallic materials and components for the space shuttle thermal protection system. Volume 3, phase 3: Full size heat shield data correlation and design criteria

Analysis methods for predicting cyclic creep deflection in stiffened metal panel structures, were applied to full size panels. Results were compared with measured deflections from cyclic tests of thin gage L605, Rene' 41, and TDNiCr full size corrugation stiffened panels. A design criteria was then formulated for metallic thermal protection panels subjected to creep. A computer program was developed to calculate creep deflections.

Cramer, B. A.↗
NASA NTRS1974

An experimental evaluation of the stresses in drilled balls

Stresses in dimensionally similar large models of 40-, 50- and 60-percent mass reduction cylindrically hollow 'drilled' bearing balls were experimentally evaluated with flat strain gage rosettes. Dimensionless principal stress coefficients were calculated and were applied to estimate the bending stresses in the drilled balls of three series of full-scale bearing experiments. Stresses were highest when the applied load approached the edge of the hole, and ranged up to almost 620 million Newtons per sq m at the bore.

Nypan, L. J.↗
NASA NTRS1975

Applications of a quadratic extended interior penalty function for structural optimization

A quadratic extended interior penalty function formulation especially well suited for second-order unconstrained optimization procedures is presented. Analytical derivatives of constraints and an approximate analysis technique are used. Minimum-mass design results are presented which indicate that the combination of these procedures can help make mathematical programming a useful optimization tool for large-order structural design problems with a large number of design variables and multiple constraints. Examples include statically loaded high- and low-aspect-ratio wings simultaneously subjected to stress, displacement, minimum gage and, in some cases, maximum strain constraints.

Haftka, R. T.↗
NASA NTRS1975

Creep analysis capability for stiffened panel structures

A method of analysis developed for predicting permanent cyclic creep deflections in stiffened panel structures is presented. The resulting computer program (TPSC, for Thermal Protection System Creep) applies either the time hardening or strain hardening theories of creep accumulation, using iterative techniques to determine structural rotations, creep strains, and stresses as a function of time. Deflections are determined by numerical integration of structural rotations along the panel length. The analytical approach was developed for purposes of analyzing thin gage entry vehicle metallic thermal protection system panels subjected to cyclic bending loads at high temperatures. The method is applicable to any panel subjected to bending loads. Predicted panel creep deflections are compared with results from cyclic tests of subsize and full size corrugation and rib stiffened panels. Empirical equations used in the analysis were developed for each material based on correlation with tensile cyclic creep data.

Cramer, B. A.↗