Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine emission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Environmentally Responsible Aviation: Propulsion Research to Enable Fuel Burn, Noise and Emissions Reduction

The NASA Environmentally Responsible Aviation (ERA) program is maturing technologies to enable simultaneous reduction of fuel burn, noise and emissions from an aircraft engine system. Three engine related Integrated Technology Demonstrations (ITDs) have been completed at Glenn Research Center in collaboration with Pratt Whitney, General Electric and the Federal Aviation Administration. The engine technologies being matured are a low NOx, fuel flexible combustor in partnership with Pratt Whitney, an ultra-high bypass, ducted propulsor system in partnership with Pratt Whitney FAA and high pressure ratio, front-stage core compressor technology in partnership with General Electric. The technical rationale, test configurations and overall results from the test series in each ITD are described. ERA is using system analysis to project the benefits of the ITD technologies on potential aircraft systems in the 2025 timeframe. Data from the ITD experiments were used to guide the system analysis assumptions. Results from the current assessments for fuel burn, noise and oxides of nitrogen emissions are presented.

Ultra-High Bypass↗

Environmentally Responsible Aviation: Propulsion Research to Enable Fuel Burn, Noise and Emissions Reduction

The NASA Environmentally Responsible Aviation (ERA) program is maturing technologies to enable simultaneous reduction of fuel burn, noise and emissions from an aircraft engine system. Three engine related Integrated Technology Demonstrations (ITDs) have been completed at Glenn Research Center in collaboration with Pratt Whitney, General Electric and the Federal Aviation Administration. The engine technologies being matured are: a low NOx, fuel flexible combustor in partnership with Pratt Whitney; an ultra-high bypass, ducted propulsor system in partnership with Pratt Whitney and FAA; and high pressure ratio, front-stage core compressor technology in partnership with General Electric. The technical rationale, test configurations and overall results from the test series in each ITD are described. ERA is using system analysis to project the benefits of the ITD technologies on potential aircraft systems in the 2025 timeframe. Data from the ITD experiments were used to guide the system analysis assumptions. Results from the current assessments for fuel burn, noise and oxides of nitrogen emissions are presented.

Noise↗

Advanced Low Emissions Subsonic Combustor Study

Recent advances in commercial and military aircraft gas turbines have yielded significant improvements in fuel efficiency and thrust-to-weight ratio, due in large part to increased combustor operating pressures and temperatures. However, the higher operating conditions have increased the emission of oxides of nitrogen (NOx), which is a pollutant with adverse impact on the atmosphere and environment. Since commercial and military aircraft are the only important direct source of NOx emissions at high altitudes, there is a growing consensus that considerably more stringent limits on NOx emissions will be required in the future for all aircraft. In fact, the regulatory communities have recently agreed to reduce NOx limits by 20 percent from current requirements effective in 1996. Further reductions at low altitude, together with introduction of limits on NOx at altitude, are virtual certainties. In addition, the U.S. Government recently conducted hearings on the introduction of federal fees on the local emission of pollutants from all sources, including aircraft. While no action was taken regarding aircraft in this instance, the threat of future action clearly remains. In these times of intense and growing international competition, the U.S. le-ad in aerospace can only be maintained through a clear technological dominance that leads to a product line of maximum value to the global airline customer. Development of a very low NOx combustor will be essential to meet the future needs of both the commercial and military transport markets, if additional economic burdens and/or operational restrictions are to be avoided. In this report, Pratt & Whitney (P&W) presents the study results with the following specific objectives: Development of low-emissions combustor technologies for advances engines that will enter into service circa 2005, while producing a goal of 70 percent lower NOx emissions, compared to 1996 regulatory levels. Identification of solution approaches to barriers to the productization and economic viability of the low-emissions technologies. Preparation of these technologies to facilitate an annular rig high-pressure demonstration.

Smith, Reid↗

Ferroelectric Emission Cathodes for Low-Power Electric Propulsion

Low- or no-flow electron emitters are required for low-power electric thrusters, spacecraft plasma contactors, and electrodynamic tether systems to reduce or eliminate the need for propellant/expellant. Expellant-less neutralizers can improve the viability of very low-power colloid thrusters, field emission electric propulsion devices, ion engines, Hall thrusters, and gridded vacuum arc thrusters. The NASA Glenn Research Center (GRC) is evaluating ferroelectric emission (FEE) cathodes as zero expellant flow rate cathode sources for the applications listed above. At GRC, low voltage (100s to approx. 1500 V) operation of FEE cathodes is examined. Initial experiments, with unipolar, bipolar, and RF burst applied voltage, have produced current pulses 250 to 1000 ns in duration with peak currents of up to 2 A at voltages at or below 1500 V. In particular, FEE cathodes driven by RF burst voltages from 1400 to 2000 V peak to peak, at burst frequencies from 70 to 400 kHz, emitted average current densities from 0.1 to 0.7 A/sq cm. Pulse repeatability as a function of input voltage has been initially established. Reliable emission has been achieved in air background at pressures as high as 10(exp -6) Torr.

Kovaleski, Scott D.↗

Simplified jet-A kinetic mechanism for combustor application

Successful modeling of combustion and emissions in gas turbine engine combustors requires an adequate description of the reaction mechanism. For hydrocarbon oxidation, detailed mechanisms are only available for the simplest types of hydrocarbons such as methane, ethane, acetylene, and propane. These detailed mechanisms contain a large number of chemical species participating simultaneously in many elementary kinetic steps. Current computational fluid dynamic (CFD) models must include fuel vaporization, fuel-air mixing, chemical reactions, and complicated boundary geometries. To simulate these conditions a very sophisticated computer model is required, which requires large computer memory capacity and long run times. Therefore, gas turbine combustion modeling has frequently been simplified by using global reaction mechanisms, which can predict only the quantities of interest: heat release rates, flame temperature, and emissions. Jet fuels are wide-boiling-range hydrocarbons with ranges extending through those of gasoline and kerosene. These fuels are chemically complex, often containing more than 300 components. Jet fuel typically can be characterized as containing 70 vol pct paraffin compounds and 25 vol pct aromatic compounds. A five-step Jet-A fuel mechanism which involves pyrolysis and subsequent oxidation of paraffin and aromatic compounds is presented here. This mechanism is verified by comparing with Jet-A fuel ignition delay time experimental data, and species concentrations obtained from flametube experiments. This five-step mechanism appears to be better than the current one- and two-step mechanisms.

Lee, Chi-Ming↗

A Comparison of Three Second-generation Swirl-Venturi Lean Direct Injection Combustor Concepts

Three variations of a low emissions aircraft gas turbine engine combustion concept were developed and tested. The concept is a second generation swirl-venturi lean direct injection (SV-LDI) concept. LDI is a lean-burn combustion concept in which the fuel is injected directly into the flame zone. All three variations were based on the baseline 9- point SV-LDI configuration reported previously. The three second generation SV-LDI variations are called the 5-recess configuration, the flat dome configuration, and the 9- recess configuration. These three configurations were tested in a NASA Glenn Research Center medium pressure flametube. All three second generation variations had better low power operability than the baseline 9-point configuration. All three configurations had low NO(sub x) emissions, with the 5-recess configuration generally having slightly lower NO(x) than the flat dome or 9-recess configurations. Due to the limitations of the flametube that prevented testing at pressures above 20 atm, correlation equations were developed for the at dome and 9-recess configurations so that the landing-takeoff NO(sub x) emissions could be estimated. The flat dome and 9-recess landing-takeoff NO(x) emissions are estimated to be 81-88% below the CAEP/6 standards, exceeding the project goal of 75% reduction.

combustor↗

Acoustic emission monitoring for assessment of steel bridge details

Acoustic emission (AE) testing was deployed on details of two large steel Interstate Highway bridges: one cantilever through-truss and one trapezoidal box girder bridge. Quantitative measurements of activity levels at known and suspected crack locations were made by monitoring AE under normal service loads (e.g., live traffic and wind). AE indications were used to direct application of radiography, resulting in identification of a previously unknown flaw, and to inform selection of a retrofit detail.

42 ENGINEERING↗

Acoustic Emission Measurement of a Wind Turbine Main Bearing

This report described acoustic emissions and temperature characteristics of a commercial main bearing in a wind turbine drivetrain. These characteristics were measured on the outer ring of the bearing by SKF DVST nodes, which are mounted on both upwind and downwind rows of the main bearing at four equally spaced circumferential locations. The measurement started in early 2018 and ends in 2020 and five-month data in 2018 winter was analyzed in this study.

17 WIND ENERGY↗

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on com- bustion stability and emissions were studied in a light-duty single- cylinder research engine for a three-injection catalyst heating oper- ation strategy with late post-injections. N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the im- pacts of volatility and reactivity. The effect of increased chemical reac- tivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representa- tive of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas in- creased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean ef- fective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane num- ber may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management opera- tion.

99 GENERAL AND MISCELLANEOUS↗

Approach to SSME health monitoring. III - Exhaust plume emission spectroscopy: Recent results and detailed analysis

Spectral data for two recent A-1 test firings, 901-717 and 901-718, obtained from an Optical Multichannel Analyzer and an Optical Plume Anomaly Detector, are presented. The spectral data encompasses the database of SSME critical components and materials and the spectral database for the SSME related elements and materials. Relatively strong and continuous emissions from Cr and Fe atomic transitions were observed starting at engine start plus 494 s and persisting until the engine shut off at engine start plus 520 s. These emissions are considered to be emanated from the SSME material AISI 440C, which is traced to high pressure turbopump bearings.

Tejwani, Gopal D.↗

Ammonia Generation over TWC for Passive SCR NOX Control for Lean Gasoline Engines

A commercial three-way catalyst (TWC) was evaluated for ammonia (NH3) generation on a 2.0-liter BMW lean burn gasoline direct injection engine as a component in a passive ammonia selective catalytic reduction (SCR) system. The passive NH3 SCR system is a potential low cost approach for controlling nitrogen oxides (NOX) emissions from lean burn gasoline engines. In this system, NH3 is generated over a close-coupled TWC during periodic slightly rich engine operation and subsequently stored on an underfloor SCR catalyst. Upon switching to lean, NOX passes through the TWC and is reduced by the stored NH3 on the SCR catalyst. NH3 generation was evaluated at different air-fuel equivalence ratios at multiple engine speed and load conditions. Near complete conversion of NOX to NH3 was achieved at =0.96 for nearly all conditions studied. At the =0.96 condition, HC emissions were relatively minimal, but CO emissions were significant. Operation at AFRs richer than =0.96 did not provide more NH3 yield and led to higher HC and CO emissions. Results of the reductant conversion and consumption processes were used to calculate a representative fuel consumption of the engine operating with an ideal passive SCR system. The results show a 1-7% fuel economy benefit at various steady-state engine speed and load points relative to a stoichiometric engine operation.

Prikhodko, Vitaly Y↗

A numerical study comparing the combustion and emission characteristics of biodiesel with petrodiesel.

Combustion and emission characteristics of compression ignition engines strongly depend upon inner-nozzle flow and spray behavior. These processes control the fuel-air mixing, which in turn is critical for the combustion process. Previous studies by us highlighted the differences in the physical and chemical properties of petrodiesel and biodiesel, which significantly altered the inner-nozzle flow and spray structure. The current study is another step in this direction to gain a fundamental understanding on the influence of fuel properties on the combustion and emission characteristics of the compression ignition engine. n-Heptane and methyl butanoate were selected as surrogates for diesel and biodiesel fuels, respectively, because the chemical kinetic pathways were well-understood. Liquid length and flame lift-off length for diesel and biodiesel fuels were validated against data available in the literature. Liquid lengths were always higher for biodiesel because of its higher heat of vaporization, which resulted in increased interplay between spray and combustion processes under all conditions investigated. Ambient air entrainment was also lower for biodiesel mainly because of slower atomization and breakup. The mechanism for flame stabilization is further analyzed by estimating the turbulent burning velocity for both of the fuels. This analysis revealed that neither flame propagation nor isolated ignition kernels upstream and detached from high-temperature regions can be the mechanism for flame stabilization. Flame propagation speeds were observed to be similar for both fuels. Biodiesel predicted lower soot concentrations, which were also reflected in reduced C{sub 2}H{sub 2} mole fractions. Although prompt NO{sub x} was higher for biodiesel, total NO{sub x} was lower because of reduced thermal NO{sub x}. The ignition delay and NO{sub x} emissions predicted by these simulations do not agree with trends reported in the literature; hence, this study highlights the need for better fuel surrogates for diesel and biodiesel fuels.

33 ADVANCED PROPULSION SYSTEMS↗

Manipulation of quantum dot emission with semiconductor metasurfaces exhibiting magnetic quadrupole resonances

Optical metasurfaces were suggested as a route for engineering advanced light sources with tailored emission properties. In particular, they provide a control over the emission directionality, which is essential for single-photon sources and LED applications. Here, we experimentally study light emission from a metasurface composed of III-V semiconductor Mie-resonant nanocylinders with integrated quantum dots (QDs). Specifically, we focus on the manipulation of the directionality of spontaneous emission from the QDs due to excitation of different magnetic quadrupole resonances in the nanocylinders. To this end, we perform both back focal plane imaging and momentum-resolved spectroscopy measurements of the emission. This allows for a comprehensive analysis of the effect of the different resonant nanocylinder modes on the emission characteristics of the metasurface. Our results show that the emission directionality can be manipulated by an interplay of the excited quadrupolar nanocylinder modes with the metasurface lattice modes and provide important insights for the design of novel smart light sources and new display concepts.

Vaskin, Aleksandr↗

Developing a heterogeneous ensemble learning framework to evaluate Alkali-silica reaction damage in concrete using acoustic emission signals

The monitoring and evaluation of Alkali-silica reaction (ASR) damage in concrete structures are required to ensure the serviceability and integrity of concrete infrastructures such as bridges and dams. The innovation of this paper lies in the development of an automatic ASR monitoring and evaluation approach by leveraging acoustic emission (AE) and a heterogeneous ensemble learning framework. Here, in this paper, ASR was monitored by AE sensors attached to a concrete specimen, which was placed in a chamber with high humidity and temperature. The recorded AE signals were filtered and divided by four ASR phases according to signal strength, crack width and expansion strain. A heterogeneous ensemble network including convolutional neural networks (CNN) and random forest models was employed to learn different features from AE signals and classify the AE signals into their corresponding phases. The results suggest that the proposed model has a high performance and classifies the signals into the assigned phases with high accuracy.

42 ENGINEERING↗

Analysis of an MCU HEPA filter

A series of direct analyses on three portions (inlet, center, and outlet) of the High Efficiency Particulate Air (HEPA) filter material from the Modular Caustic-Side Solvent Extraction Unit (MCU) have been performed; this includes x-ray methods such as X-Ray Diffraction (XRD), Contained Scanning Electron Microscopy (CSEM) and X-Ray Fluorescence (XRF), as well as Fourier Transform InfraRed spectroscopy (FTIR). Additionally, two leaching studies (one with water, one with dichloromethane) have been performed on three portions (inlet, center, and outlet) of the HEPA filter material, with the leachates being analyzed by Inductively-coupled plasma emission spectroscopy (ICPES), Semi-Volatile Organic Analysis (SVOA) and gammascan. From the results of the analyses, SRNL feels that cesium-depleted solvent is being introduced into the HEPA filter. The most likely avenue for this is mechanical aerosolization of solvent, where the aerosol is then carried along an airstream into the HEPA filter. Once introduced into the HEPA filter media, the solvent wicks throughout the material, and migrates towards the outlet end. Once on the outlet end, continual drying could cause particulate flakes to exit the filter and travel farther down the airstream path.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of Fuel Vaporization, Fuel-Air Mixing, and Combustion in Integrated Mixer-Flame Holders

Requirements to limit pollutant emissions from the gas turbine engines for the future High-Speed Civil Transport (HSCT) have led to consideration of various low-emission combustor concepts. One such concept is the Integrated Mixer-Flame Holder (IMFH). This report describes a series of IMFH analyses performed with KIVA-II, a multi-dimensional CFD code for problems involving sprays, turbulence, and combustion. To meet the needs of this study, KIVA-II's boundary condition and chemistry treatments are modified. The study itself examines the relationships between fuel vaporization, fuel-air mixing, and combustion. Parameters being considered include: mixer tube diameter, mixer tube length, mixer tube geometry (converging-diverging versus straight walls), air inlet velocity, air inlet swirl angle, secondary air injection (dilution holes), fuel injection velocity, fuel injection angle, number of fuel injection ports, fuel spray cone angle, and fuel droplet size. Cases are run with and without combustion to examine the variations in fuel-air mixing and potential for flashback due to the above parameters. The degree of fuel-air mixing is judged by comparing average, minimum, and maximum fuel/air ratios at the exit of the mixer tube, while flame stability is monitored by following the location of the flame front as the solution progresses from ignition to steady state. Results indicate that fuel-air mixing can be enhanced by a variety of means, the best being a combination of air inlet swirl and a converging-diverging mixer tube geometry. With the IMFH configuration utilized in the present study, flashback becomes more common as the mixer tube diameter is increased and is instigated by disturbances associated with the dilution hole flow.

Deur, J. M.↗

Microwave Irradiation Intensified Process for Scalable Functional Device Assembly

The environment pollution is a serious issue worldwide for human beings, which calls for ever-increasing demand towards environmental protection. Efficient enabling and utilization of various functional devices represent an essential solution to pursue the environment sustainability. Nanotechnology is emerging as an effective approach to improve the efficiency of functional devices for a variety of environmental applications. For example, the nanomaterials-based catalysts are being widely used in air pollution control, enabling catalysts with significantly enhanced performance. Scalable integration of functional nanostructural entities such as nanoparticles, nanowires, nanosheets into applicable three-dimensional (3-D) platform holds the keys of industrial-relevant manufacture of high-efficiency catalytic devices for emission control. Among all the integration approaches, the wet-chemical based integration is one of the top options due to its advantages in low-cost, flexibility in substrate geometry and composition, ease of operation, and high repeatability. The wet-chemical based processes usually require continuous heating to initiate the chemical reactions, which is regularly achieved by conventional resistive heating. However, such conventional heating method is plaqued by a poor heating efficiency. Moreover, the conventional heating is not suitable for those substrates with three-dimensional (3D) or complex geometry since it hardly provides sufficient heat transfer and mass transport within substrates, leading to poor uniformity of nanostructure deposition and low production rate. Thus, there is urgent demand to develop high-efficiency wet-chemical based integration strategy for nanostructured functional devices. In this project, a novel microwave-irradiation-intensified hydrothermal manufacturing process was developed for scalable manufacture of nanostructured monolithic catalytic devices. A wide array of metal oxide nanostructured coatings has been in situ grown on various 3D substrates for emission control applicaitons such as cordierite honeycombs and silicon carbide honeycomb. The growth efficiency, production rate, and distribution uniformity of nanostructure coatings obtained from microwave heating and conventional heating are investigated, which reveals the boosting effect of microwave irradiation on hydrothermal reactions. The silicon carbide honeycomb is found to be more favorable to microwave adsorption in contrast to cordierite honeycomb, and the corresponding reaction mechanism is studied. The obtained catalysts are used for catalytic oxidation of Volatile Organic Compounds (VOCs), showing excellent catalytic performance at low temperature for various compounds. As the proof of concept, the design of integrated manufacturing system for the microwave irradiation assisted continuous production of nanostructure array based monolithic catalysts is presented, which holds the key to mass production of monolithic catalysts in near future.

42 ENGINEERING↗

Fuel Composition Influences on Reciprocating Engine Performance

The introduction of new fuels into the market is a unique opportunity to take advantage of new fuel compositions to improve the efficiency and emissions of internal combustion reciprocating engines and alternative fuel feedstocks. However, there are numerous challenges that introductions of new fuels face before they can become first legal, then ubiquitous. This chapter reviews four different case studies related to changing fuel composition. In some circumstances, the fuel formulation was changed in seemingly minor ways, and resulted in the unanticipated consequences. In other cases, a fuel change was desired, but an unexpected barrier slowed the introduction of the fuel change. These case studies should be viewed as opportunities to understand the interdependencies that exist and factors that need to be considered when trying to change the fuel in the marketplace.

Szybist, James↗