Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrode materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Developing an In-situ Formed Dynamic Protection Layer to Mitigate Lithium Interface Shifting: Preventing Dendrite Formation on Metallic Lithium Surface to Facilitate Long Cycle Life of Lithium Solid-State Batteries

After extensive research on various system, a fully lithiated Si anode material (Li 3.75 Si) was synthesized. The high energy density, long cycle life anode demonstrated no apparent dendrite growth in an all-solid-state Li battery. A flexible solid-state electrolyte film with a thickness less than 50 μm was developed. All-solid-state Li full batteries were built and tested with NMC811, organic, organosulfide and sulfur cathode. Energy density of 1140 Wh/Kg at material level and 376 Wh/Kg at electrode level were demonstrated for over 500 cycles and with no apparent dendrite formation on the Li anode.

25 ENERGY STORAGE↗
DOE OSTI2024

Active Aerodynamic Load Control for Wind Turbines

The goal of this project was to develop and demonstrate an advanced dielectric barrier discharge (DBD) plasma actuator technology. We set out to demonstrate the efficacy and impact of the new actuator technology as a key component of an active load control system for wind turbines. A DBD plasma actuator consists of a thin layer of dielectric material separating a pair of offset electrodes. One of those electrodes is embedded between the dielectric layer and a non-conductive substrate, while the other is exposed to air. When driven by an appropriate high voltage waveform, the device ionizes the air near the surface of the dielectric and adjacent to the exposed electrode. Collisions between the ions in the plasma and neutral air molecules result in a wall-jet – a region of induced air velocity that can be used to modify the flow around a lifting body. Use of the device near the trailing edge of a wind turbine blade, designed in such a way as to amplify the effects of the flow-modifying device, can result in large changes to the global forces experienced by the blade. Because of the fast response time of the device, it can allow the turbine to react in real time to changes in the wind associated with turbulence, wind shear, gusts, and the like, when paired with appropriate sensors and control algorithms. The goal of this project was to increase the capacity of the device to induce velocity on its surface at the levels required by large, utility-scale wind turbines. The first technical goal was to increase the induced velocity from the current industry-best of about 4 m/s to 10 m/s by modifying the electrical waveform used to drive the device and by introducing a semi-conductive surface coating to control electrostatic charge build-up on the surface. The second goal was to use the device to modify the lift on a representative airfoil in a wind tunnel, demonstrating a reduction in lift coefficient of 0.2 or better. The third goal was to produce an actuator-induced velocity of 20 m/s. Alongside our partners at the University of Texas at Dallas, we also applied modern, advanced design methods to optimize the impact of the technology on the design of wind turbines. We also had planned to install a segmented, active load control system on a test turbine to demonstrate the ability to reduce unsteady aerodynamic forces on the turbine associated with changes in the wind. The highest induced velocity achieved during this research was 11 m/s. However, practical design constraints limited the change in lift coefficient to about 0.12 for a representative airfoil in the wind tunnel at a Reynolds number of 400,000. The primary conclusion is that the plasma actuator control authority remains insufficient for practical purposes when extrapolated to Reynolds numbers over 1 million. The potential impact of the active lift control concept was evaluated through detailed simulations for three wind turbine sizes: a 3.4MW onshore turbine, a 10MW offshore turbine, and a 15MW offshore turbine. A feedback control system was designed for each turbine within two scenarios: one where the active lift control is used as a retrofit capability on the baseline design, and the other where the designers were permitted to “upscale” the turbines in order increase annual energy production. The levelized cost of energy was then evaluated for the range of turbine sizes and design configuration. It was found that the LCOE reduction associated with active lift control fell in the range of 0.7% to 7.2%, with the highest reduction associated with upscaling the 3.4MW turbine.

17 WIND ENERGY↗
DOE OSTI2020

Field controlled direct-write electrospinning

The invention provides a method for producing fibers, the method having the steps of producing electrospun fiber; and directing the fiber to a plurality of targets, whereby only one of the targets is grounded at any one time. Also provided is a system for producing anisotropic fibers having a reservoir of electrospun fiber constituent' wherein an egress point of the reservoir is electrically charged; a plurality of electrodes opposed to the egress point, wherein only one of the electrodes is grounded at any one time while the remaining electrodes are at an initial floating voltage state; and a target substrate disposed between the egress point and the plurality of electrodes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stamping Nanoparticles onto the Electrode for Rapid Electrochemical Analysis in Microfluidics

Electrochemical analysis is an efficient way to study various materials. However, nanoparticles are challenging due to the difficulty in fabricating a uniform electrode containing nanoparticles. We developed novel approaches to incorporate nanoparticles as a working electrode (WE) in a three-electrode microfluidic electrochemical cell. Specifically, conductive epoxy was used as a medium for direct application of nanoparticles onto the electrode surface. Three approaches in this work were illustrated, including sequence stamping, mix stamping, and droplet stamping. Shadow masking was used to form the conductive structure in the WE surface on a thin silicon nitride (SiN) membrane. Two types of nanomaterials, namely cerium oxide (CeO2) and graphite, were chosen as representative nanoparticles. The as-fabricated electrodes with attached particles were characterized using atomic force microscopy (AFM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Electrochemical analysis was performed to verify the feasibility of these nanoparticles as electrodes. Nanomaterials can be quickly assessed for their electrochemical properties using these new electrode fabrication methods in a microfluidic cell, offering a passport for rapid nanomaterial electrochemical analysis in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Electrochemical Characterization of Degradation Modes of High-Voltage Li x Ni 0.33 Mn 0.33 Co 0.33 O 2 Electrodes

While deeply charged high-voltage cathodes can improve battery energy density, understanding and preventing any accelerated cell degradation is crucial to practical success. Here, to analyze the degradation of LiNi x Mn y Co 1–x–y O 2 (NMC) type material charged to 4.3 and 4.5 V, a physics-based model is applied to cycling data to obtain parameter estimates indicative of degradation modes, which are validated by simple electrochemical measurements and further interpreted by materials characterization. Growth rates of interfacial impedance and active material loss are greater at 4.5 V, as might be expected. However, when charged to 4.5 V, degradation rates are initially lower at a cycling C-rate of 1.0 C than at 0.5 C. Once degradation mode changes are quantified, simulations evaluate the contribution of individual degradation mode to performance losses and provide estimates of the energy-power correlation (Ragone plots) of cells after cycling.

25 ENERGY STORAGE↗
DOE OSTI2020

Fabricating double-sided electrodynamic screen films

An electrode film is fabricated by using a flexographic printing system to print a first electrode pattern including a first set of parallel electrodes and a second electrode pattern including a second set of parallel electrodes onto a first surface of a transparent film using a catalytic ink, wherein elements of the first electrode pattern do not cross over elements of the second electrode pattern. The flexographic printing system prints a third electrode pattern including a third set of parallel electrodes onto a second surface of the transparent film using the catalytic ink, wherein the first, second and third sets of parallel electrodes are arranged in an interlaced pattern. A conductive metallic material is electrolessly plated onto the catalytic ink such that the elements of the first, second and third electrode patterns become conductive.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Capturing carbon dioxide from air with charged-sorbents

Emissions reduction and greenhouse gas removal from the atmosphere are both necessary to achieve net-zero emissions and limit climate change. There is thus a need for improved sorbents for the capture of carbon dioxide from the atmosphere, a process known as direct air capture. In particular, low-cost materials that can be regenerated at low temperatures would overcome the limitations of current technologies. In this work, we introduce a new class of designer sorbent materials known as ‘charged-sorbents’. These materials are prepared through a battery-like charging process that accumulates ions in the pores of low-cost activated carbons, with the inserted ions then serving as sites for carbon dioxide adsorption. We use our charging process to accumulate reactive hydroxide ions in the pores of a carbon electrode, and find that the resulting sorbent material can rapidly capture carbon dioxide from ambient air by means of (bi)carbonate formation. Unlike traditional bulk carbonates, charged-sorbent regeneration can be achieved at low temperatures (90–100 °C) and the sorbent’s conductive nature permits direct Joule heating regeneration using renewable electricity. Given their highly tailorable pore environments and low cost, we anticipate that charged-sorbents will find numerous potential applications in chemical separations, catalysis and beyond.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Proton-exchange induced reactivity in layered oxides for lithium-ion batteries

LiNi x Co y Mn 1-x-y O 2 (0 < x, y < 1, NCM) is the dominant positive material for the state-of-the-art lithium-ion batteries. However, the sensitivity of NCM materials to moisture makes their manufacturing, storage, transportation, electrode processing and recycling complicated. Although it is recognized that protons play a critical role in their structure stability and performance, proton exchange with Li + in NCM materials has not been well understood. Here, we employ advanced characterizations and computational studies to elucidate how protons intercalate into the layered structure of NCM, leading to the leaching of Li + and the formation of protonated NCM. It is found that protonation facilitates cation rearrangement and formation of impurity phases in NCM, significantly deteriorating structural stability. The adverse effects induced by protons become increasingly pronounced with a higher Ni content in NCM. Through a comprehensive investigation into the thermodynamics and kinetics of protonation, we discover that Li deficiencies in NCM materials can be resolved via solution process in the presence of Li + ions and controlled proton concentration. The underlying mechanism of relithiation is further explored through materials characterizations and kinetics modeling. This work provides crucial insights into controlling structural and compositional defects of Li-ion battery positive material in complicated processing environment.

batteries↗
DOE OSTI2021

Using In Situ High-Energy X-ray Diffraction to Quantify Electrode Behavior of Li-Ion Batteries from Extreme Fast Charging

Extreme fast charging (XFC, =15 min charging time) of Li-ion batteries (LIBs) has been proposed as an immediate target to increase the commercial appeal of electric vehicles. However, XFC of LIBs is associated with the degradation of battery performance and safety concerns. Quantitative and simultaneous characterization of various components during cell degradation represents a major experimental challenge. In this work, we outline a methodology for the use of spatially resolved, high-energy X-ray diffraction as a quantitative, in situ method of mapping the degradation of LIBs. We use this approach to study the battery cell capacity loss, both locally (mm scale) and globally over the entire cell (cm scale). Specifically, our workflow allows us to quantify the total amount of plated Li on the anode, as well as its spatial correlation to the structural properties of the anode and cathode. The method complements existing optical methods to resolve the spatial heterogeneity of local degradation mechanisms such as Li plating and provides simultaneous insights into concomitant anode state-of-charge variability. We apply it to commercially relevant single-layer pouch cells with the graphite anode and the LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathode. Our results show that Li plating occurs heterogeneously on the graphite anode and that it is spatially correlated to the extent of anode lithiation. In this work, we anticipate that the described workflow will allow for understanding multiscale degradation in energy-storage devices beyond LIBs, where quantitative analysis at a local and global length scale can be performed without the necessity to tear down the device, due to the applicability of high-energy X-rays to probe in situ degradation.

25 ENERGY STORAGE↗
DOE OSTI2023

Cation-Driven Assembly of Bilayered Vanadium Oxide and Graphene Oxide Nanoflakes to Form Two-Dimensional Heterostructure Electrodes for Li-Ion Batteries

Lithium preintercalated bilayered vanadium oxide (LVO or δ-Li x V 2 O 5 ·nH 2 O) and graphene oxide (GO) nanoflakes were assembled using a concentrated lithium chloride solution and annealed under vacuum at 200 °C to form two-dimensional (2D) δ-Li x V 2 O 5 ·nH 2 O and reduced GO (rGO) heterostructures. Here we found that the Li + ions from LiCl enhanced the oxide/carbon heterointerface formation and served as stabilizing ions to improve structural and electrochemical stability. The graphitic content of the heterostructure could be easily controlled by changing the initial GO concentration prior to assembly. We found that increasing the GO content in our heterostructure composition helped inhibit the electrochemical degradation of LVO during cycling and improved the rate capability of the heterostructure. A combination of scanning electron microscopy and X-ray diffraction was used to help confirm that a 2D heterointerface formed between LVO and GO, and the final phase composition was determined using energy-dispersive X-ray spectroscopy and thermogravimetric analysis. Scanning transmission electron microscopy and electron energy-loss spectroscopy were additionally used to examine the heterostructures at high resolution, mapping the orientations of rGO and LVO layers and locally imaging their interlayer spacings. Further, electrochemical cycling of the cation-assembled LVO/rGO heterostructures in Li-ion cells with a non-aqueous electrolyte revealed that increasing the rGO content led to improved cycling stability and rate performance, despite slightly decreased charge storage capacity. The heterostructures with 0, 10, 20, and 35 wt % rGO exhibited capacities of 237, 216, 174, and 150 mAh g –1 , respectively. Moreover, the LVO/rGO-35 wt % and LVO/rGO-20 wt % heterostructures retained 75% (110 mAh g–1) and 67% (120 mAh g –1 ) of their initial capacities after increasing the specific current from 20 to 200 mA g –1 , while the LVO/rGO-10 wt % sample retained only 48% (107 mAh g –1 ) of its initial capacity under the same cycling conditions. In addition, the cation-assembled LVO/rGO electrodes exhibited enhanced electrochemical stability compared to electrodes prepared through physical mixing of LVO and GO nanoflakes in the same ratios as the heterostructure electrodes, further revealing the stabilizing effect of a 2D heterointerface. The cation-driven assembly approach, explored in this work using Li + cations, was found to induce and stabilize the formation of stacked 2D layers of rGO and exfoliated LVO. The reported assembly methodology can be applied for a variety of systems utilizing 2D materials with complementary properties for applications as electrodes in energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2022

Sodium trithiocarbonate cathode for high-performance sodium–sulfur batteries

The high abundance and low cost of sodium and sulfur make room-temperature sodium-sulfur (RT Na-S) batteries an attractive technology compared to the current lithium-ion batteries for large-scale grid-storage applications. However, the commercialization of RT Na-S batteries is impeded by the slow kinetics of Na-S chemistry, severe sodium polysulfide shuttling, and uncontrollable growth of dendritic Na. Herein, sodium trithiocarbonate (Na 2 CS 3 ) is applied as a cathode material to facilitate concurrent improvement in both electrodes, leading to a high-rate performance with extended cycle life. The conductive characteristic of the carbon-sulfur resonance bond provides fast ion and electron transfer throughout the cathode, resulting in superior electrochemical reactivity. At the cathode, the presence of Na2CS3 forms an oligomer-structured layer to suppress the dissolution and shuttling of active materials. Meanwhile, when small portions of Na 2 CS 3 intermediates migrate to the anode, a stable solid electrolyte interphase (SEI) layer with uniform Na-ion flux is formed, enabling improved Na stripping and plating performance. A series of electrochemical and materials characterization, accompanied by density functional theory calculations demonstrate that Na 2 CS 3 is a promising candidate to realize high-rate performance long cycle life RT Na-S batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Catalytic, Spectroscopic, and Theoretical Studies of Fe 4 S 4 -Based Coordination Polymers as Heterogenous Coupled Proton–Electron Transfer Mediators for Electrocatalysis

Iron–sulfur clusters play essential roles in biological systems, and thus synthetic [Fe 4 S 4 ] clusters have been an area of active research. Recent studies have demonstrated that soluble [Fe 4 S 4 ] clusters can serve as net H atom transfer mediators, improving the activity and selectivity of a homogeneous Mn CO 2 reduction catalyst. Here, in this work, we demonstrate that incorporating these [Fe 4 S 4 ] clusters into a coordination polymer enables heterogeneous H atom transfer from an electrode surface to a Mn complex dissolved in solution. A previously reported solution-processable Fe 4 S 4 -based coordination polymer was successfully deposited on the surfaces of different electrodes. The coated electrodes serve as H atom transfer mediators to a soluble Mn CO 2 reduction catalyst displaying good product selectivity for formic acid. Furthermore, these electrodes are recyclable with a minimal decrease in activity after multiple catalytic cycles. The heterogenization of the mediator also enables the characterization of solution-phase and electrode surface species separately. Surface enhanced infrared absorption spectroscopy (SEIRAS) reveals spectroscopic signatures for an in situ generated active Mn–H species, providing a more complete mechanistic picture for this system. The active species, reaction mechanism, and the protonation sites on the [Fe 4 S 4 ] clusters were further confirmed by density functional theory calculations. The observed H atom transfer reactivity of these coordination polymer-coated electrodes motivates additional applications of this composite material in reductive H atom transfer electrocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Review—The Lithiation/Delithiation Behavior of Si-Based Electrodes: A Connection between Electrochemistry and Mechanics

Silicon is a promising alternative anode material to graphite because of its high gravimetric and volumetric energy densities. However, severe capacity fading is observed in Si electrodes, and it is a result of mechanical changes of Si, such as volume changes, stress or fracture. Furthermore, these mechanical behaviors are strongly coupled with the electrochemistry of the Li-Si alloying reaction in Si-based electrodes, including both thermodynamics and kinetics. Therefore, the electrochemical properties of Si-based electrodes are strongly dependent on the control of the mechanics of Si during lithiation/delithiation. As such, it is very important to understand the correlation between electrochemistry and mechanics. Here, we review lithiation/delithiation behaviors of various types of Si-based electrodes, applying a fundamental understanding of electrochemistry and mechanics and the correlation between them.

25 ENERGY STORAGE↗
DOE OSTI2024

Binder-Coated Carbon Cloth Electrodes for All-Vanadium Redox Flow Batteries

Vanadium redox flow batteries (VRFBs) are a promising solution for integrating intermittent renewable energy sources into the existing power grid. However, enhancing the electrochemical performance of VRFBs is critical for their widespread adoption in grid-scale energy storage. This study investigates the impact of adding a porous binder to a carbon-cloth electrode, with a focus on optimizing thermal activation conditions. The electrochemical performance of the binder-coated electrodes compared to uncoated electrodes is evaluated through electrochemical impedance spectroscopy, polarization curve measurements, and charge-discharge cycling. The surface morphology and structural integrity of the binder-coated electrodes at each activation stage are examined using various material characterization techniques to assess the effects of thermal activation. The results are benchmarked against the experiments using non-coated electrodes to determine the performance improvements offered by the binder coating. Notably, the study reveals that binder-coated electrodes exhibit significantly lower resistance and improved efficiency compared to their uncoated counterparts, with optimal activation conditions enhancing performance metrics crucial for VRFB applications. These findings provide valuable insights for further optimizing electrode design and activation strategies, advancing the development of more efficient VRFB systems for large-scale energy storage.

Caiado, Ashley A.↗
DOE OSTI2023

Development of Nanocomposite Coatings for Future Large-Scale Time Projection Chambers

In the context of this award we tested the performance of thin high-resistivity coatings for their potential usage as field shaping systems in future large scale xenon Time Projection Chambers (TPC). A successful implementation of such thin coatings would likely simplify the design of potential future detectors, allowing to overcome some of the challenges observed with traditional systems constituted by massive discrete electrodes. We studied a wide range of materials and characterized their optical and electrical performances as functions of temperature and wavelength. The measurement campaign indicated that uniform coatings covering the full PTFE substrate (usually used as reflector in LXe TPCs) impact too severely on the light collection performance of such detectors when used with deep UV light. Despite tuning the composition and thicknesses of nanocomposite coatings, we were not able to identify a single coating, properly working at LXe temperature, that would simultaneously fulfill the resistance and optical requirements. Following the risk mitigation strategy identified in the proposal we moved the focus of the R&D to identify proper materials that, when coated with grid-like patterns on PTFE, would not alter meaningfully its optical properties (with respect to bare PTFE panels) but would still serve as effective field shaping systems, properly containing the drift field in TPC detectors. Among the various materials we identified germanium as the most promising one, providing a good adhesion to PTFE and the proper range of sheet resistivity. The Ge-patterned coating tested within a small scale LXe TPC showed good performance as a field shape system and, as desired, did not reduce the detector light yield. These results are encouraging and such technology should further be investigated as a potential alternative to more traditional field shaping electrodes. Incidentally, in the context of this R&D, we stumbled upon an unexpected behavior suggesting that some of the treatments performed on the PTFE panels, in preparation of the coatings, meaningfully boosted the PTFE reflectivity. The most probable candidate is the O2 plasma cleaning procedure. This hypothesis will be tested in the near future by operating the small scale TPC at UChicago first with regular PTFE panels and then with panels bombarded with O2 plasma (but no coatings). This finding, if confirmed, might open up the possibility of further boosting UV light collection in future large detectors by performing such a treatment on the PTFE surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Crosslinked polymer binders for electrochemical energy storage devices

An electrochemical storage device including a conductive material and an electrochemical storage device material held together by a covalently crosslinked binder matrix. A method of forming an electrode for an electrochemical storage device, the method including the steps of: mixing electrochemical storage device material, conductive material, linear polymer, and crosslinker with one or more solvents, the resultant mixture forming an electrode slurry, crosslinking the linear polymer with the crosslinker to thereby create a covalently crosslinked polymer network of the polymer and crosslinker, the crosslinked polymer network physically or chemically binding together the electrochemical storage device material and the conductive material.

Zhu, Yu↗