Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPECTATION VALUE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Surveillance Range and Interference Impacts on Self-Separation Performance

Self-separation is a concept of flight operations that aims to provide user benefits and increase airspace capacity by transferring traffic separation responsibility from ground-based controllers to the flight crew. Self-separation is enabled by cooperative airborne surveillance, such as that provided by the Automatic Dependent Surveillance-Broadcast (ADSB) system and airborne separation assistance technologies. This paper describes an assessment of the impact of ADS-B system performance on the performance of self-separation as a step towards establishing far-term ADS-B performance requirements. Specifically, the impacts of ADS-B surveillance range and interference limitations were analyzed under different traffic density levels. The analysis was performed using a batch simulation of aircraft performing self-separation assisted by NASA s Autonomous Operations Planner prototype flight-deck tool, in two-dimensional airspace. An aircraft detected conflicts within a look-ahead time of ten minutes and resolved them using strategic closed trajectories or tactical open maneuvers if the time to loss of separation was below a threshold. While a complex interaction was observed between the impacts of surveillance range and interference, as both factors are physically coupled, self-separation performance followed expected trends. An increase in surveillance range resulted in a decrease in the number of conflict detections, an increase in the average conflict detection lead time, and an increase in the percentage of conflict resolutions that were strategic. The majority of the benefit was observed when surveillance range was increased to a value corresponding to the conflict detection look-ahead time. The benefits were attenuated at higher interference levels. Increase in traffic density resulted in a significant increase in the number of conflict detections, as expected, but had no effect on the conflict detection lead time and the percentage of conflict resolutions that were strategic. With surveillance range corresponding to ADS-B minimum operational performance standards for Class A3 equipment and without background interference, a significant portion of conflict resolutions, 97 percent, were achieved in the preferred strategic mode. The majority of conflict resolutions, 71 percent, were strategic even with very high interference (over three times that expected in 2035).

Idris, Husni↗
NASA NTRS2009

C-12/C-13 Ratio in Ethane on Titan and Implications for Methane's Replenishment

The C-12/C-13 abundance ratio in ethane in the atmosphere of Titan has been measured at 822 cm(sup -1) from high spectral resolution ground-based observations. The value 89(8), coincides with the telluric standard and also agrees with the ratio seen in the outer planets. It is almost identical to the result for ethane on Titan found by the composite infrared spectrometer (CIRS) on Cassini. The C-12/C-13 ratio for ethane is higher than the ratio measured in atmospheric methane by Cassini/Huygens GCMS, 82.3(l), representing an enrichment of C-12 in the ethane that might be explained by a kinetic isotope effect of approximately 1.1 in the formation of methyl radicals. If methane is being continuously resupplied to balance photochemical destruction, then we expect the isotopic composition in the ethane product to equilibrate at close to the same C-12/C-13 ratio as that in the supply. The telluric value of the ratio in ethane then implies that the methane reservoir is primordial.

Jennings, Donald E.↗
NASA NTRS1994

Interhemispheric asymmetry of the high-latitude ionospheric convection pattern

The assimilative mapping of ionospheric electrodynamics technique has been used to derive the large-scale high-latitude ionospheric convection patterns simultaneously in both northern and southern hemispheres during the period of January 27 to 29, 1992. When the interplanetary magnetic field (IMF) B(sub z) component is negative, the convection patterns in the southern hemisphere are basically the mirror images of those in the northern hemisphere. The total cross-polar cap potential drops in the two hemispheres are similar. When B(sub z) is positive and absolute value of B(sub y) greater than B(sub z), the convection configurations are mainly determined by B(sub y) and they may appear as normal 'two-cell' patterns in both hemispheres much as one would expect under southward IMF conditions. However, there is a significant difference in the cross-polar-cap potential drop between the two hemispheres, with the potential drop in the southern (summer) hemisphere over 50% larger than that in the northern (winter) hemisphere. As the ratio of absolute value of B(sub y)/B(sub z) decreases (less than one), the convection configuration in the two hemispheres may be significantly different, with reverse convection in the southern hemisphere and weak but disturbed convection in the northern hemisphere. By comparing the convection patterns with the corresponding spectrograms of precipitating particles, we interpret the convection patterns in terms of the concept of merging cells, lobe cells, and viscous cells. Estimates of the ' merging cell' potential drops, that is, the potential ascribed to the opening of the dayside field lines, are usually comparable between the two hemispheres, as they should be. The 'lobe cell' provides a potential between 8.5 and 26 kV and can differ greatly between hemispheres, as predicted. Lobe cells can be significant even for southward IMF, if absolute value of B(sub y) greater than the absolute value of B(sub z). To estimate the potential drop of the 'viscous cells,' we assume that the low-latitude boundary layer is on closed field lines. We find that this potential drop varies from case to case, with a typical value of 10 kV. If the source of these cells is truly a viscous interaction at the flank of the magnetopause, the process is likely spatially and temporally varying rather than steady state.

Lu, G.↗
NASA NTRS2008

Anticipating Cycle 24 Minimum and its Consequences: An Update

This Technical Publication updates estimates for cycle 24 minimum and discusses consequences associated with cycle 23 being a longer than average period cycle and cycle 24 having parametric minimum values smaller (or larger for the case of spotless days) than long term medians. Through December 2007, cycle 23 has persisted 140 mo from its 12-mo moving average (12-mma) minimum monthly mean sunspot number occurrence date (May 1996). Longer than average period cycles of the modern era (since cycle 12) have minimum-to-minimum periods of about 139.0+/-6.3 mo (the 90-percent prediction interval), inferring that cycle 24 s minimum monthly mean sunspot number should be expected before July 2008. The major consequence of this is that, unless cycle 24 is a statistical outlier (like cycle 21), its maximum amplitude (RM) likely will be smaller than previously forecast. If, however, in the course of its rise cycle 24 s 12-mma of the weighted mean latitude (L) of spot groups exceeds 24 deg, then one expects RM >131, and if its 12-mma of highest latitude (H) spot groups exceeds 38 deg, then one expects RM >127. High-latitude new cycle spot groups, while first reported in January 2008, have not, as yet, become the dominant form of spot groups. Minimum values in L and H were observed in mid 2007 and values are now slowly increasing, a precondition for the imminent onset of the new sunspot cycle.

Wilson, Robert M.↗
NASA NTRS1971

Integrating a multifaceted system safety program for a large complex system

A safety systems effectiveness analysis is developed that considers the extent to which a system may be expected to achieve a set of stated system objectives by determining the interrelationships between reliability, maintainability, quality assurance, human factors, and value engineering.

W. W. Malasky↗
NASA NTRS1974

Quantized vortices around wavefront nodes, 2

Quantized vortices can occur around nodal points in wavefunctions. The derivation depends only on the wavefunction being single valued, continuous, and having continuous first derivatives. Since the derivation does not depend upon the dynamical equations, the quantized vortices are expected to occur for many types of waves such as electromagnetic and acoustic. Such vortices have appeared in the calculations of the H + H2 molecular collisions and play a role in the chemical kinetics. In a companion paper, it is shown that quantized vortices occur when optical waves are internally reflected from the face of a prism or particle beams are reflected from potential energy barriers.

Hirschfelder, J. O.↗
NASA NTRS1974

Sonic-boom measurements in the focus region during the ascent of Apollo 17

Sonic-boom pressure signatures recorded during the ascent phase of Apollo 17 are presented. The measurements were obtained onboard six U.S. Navy ships positioned along the ground track of the spacecraft vehicle in the area of expected focus resulting from the flight path and acceleration of the vehicle. Tracings of the measured signatures are presented along with values of the maximum positive overpressure, positive impulse, signature duration, and bowshock rise time. Also included are brief descriptions of the ships and their location, the deployment of the sonic-boom instrumentation, flight profiles and operating conditions for the launch vehicle and spacecraft, surface-weather and sea-state information at the measuring sites, and high-altitude weather information for the general measurement areas. Comparisons of the measured and predicted sonic-boom overpressures for the Apollo 17 mission are presented. The measured data are also compared with data from the Apollo 15 and 16 missions and data from flight test programs of various aircraft.

Henderson, H. R.↗
NASA NTRS1975

Thermally generated magnetic fields in laser-driven compressions and explosions

The evolution of thermally generated magnetic fields in a plasma undergoing a nearly spherically symmetric adiabatic compression or expansion is calculated. The analysis is applied to obtain approximate results for the development of magnetic fields in laser-driven compression and explosion of a pellet of nuclear fuel. Localized sources, such as those occurring at composition boundaries in structured pellets or at shock fronts, give stronger fields than those deriving from smoothly distributed asymmetries. Although these fields may approach 10 million G in the late stages of compression, this is not expected to present difficulties for the compression process. Assuming ignition of a nuclear explosion occurs, the sources become much stronger, and values of approximately 10 billion G are obtained at tamper boundaries assuming a 20% departure from spherical symmetry during the explosion.

Tidman, D. A.↗
NASA NTRS1984

Physical conditions in the cool parts of spicules

The resonance lines of Na, Sr(+), and the Mg triplet system, together with the middle H Balmer lines, are used to determine the plasma parameters in the cool parts of spicules. Results are presented for the heights 2100 and 2500 km according to the chromospheric line emission data reported by Dunn et al. (1968) for the 1962 eclipse. The low flow-velocity solutions require unsatisfactorily high temperature and microturbulence values (the derived thicknesses are also uncomfortably large). The remaining solutions have flow velocities and thicknesses that are in line with expectations from direct spicule observations, and the electron densities are comparable to those obtained from continuum measurements at the 1952 eclipse. However, contrary to most preconceptions, hydrogen is found to be predominantly neutral in these regions; the total gas pressure is consequently quite large - in fact, exceeding the adjacent interspicular pressure by about a factor of 10.

Landman, D. A.↗
NASA NTRS1992

Damage tolerance of a composite sandwich with interleaved foam core

A composite sandwich panel consisting of carbon fiber-reinforced plastic (CFRP) skins and a syntactic foam core was selected as an appropriate structural concept for the design of wind tunnel compressor blades. Interleaving of the core with tough interlayers was done to prevent core cracking and to improve damage tolerance of the sandwich. Simply supported sandwich beam specimens were subjected to low-velocity drop-weight impacts as well as high velocity ballistic impacts. The performance of the interleaved core sandwich panels was characterized by localized skin damage and minor cracking of the core. Residual compressive strength (RCS) of the skin, which was derived from flexural test, shows the expected trend of decreasing with increasing size of the damage, impact energy, and velocity. In the case of skin damage, RCS values of around 50 percent of the virgin interleaved reference were obtained at the upper impact energy range. Based on the similarity between low-velocity and ballistic-impact effects, it was concluded that impact energy is the main variable controlling damage and residual strength, where as velocity plays a minor role.

Ishai, Ori↗
NASA NTRS2000

Diurnal Variability of the Hydrologic Cycle and Radiative Fluxes: Comparisons Between Observation and a GCM

The simulated diurnal cycle is in many ways an ideal test bed for new physical parameterizations. The purpose of this paper is to compare observations from the Tropical Rainfall Measurement Mission, the Earth Radiation Budget Experiment, the International Satellite Cloud Climatology Project, the Clouds and the Earth's Radiant Energy System Experiment, and the Anglo-Brazilian Amazonian Climate Observation Study with the diurnal variability of the Amazonian hydrologic cycle and radiative energy budget as simulated by the Colorado State University general circulation model, and to evaluate improvements and deficiencies of the model physics. The model uses a prognostic cumulus kinetic energy (CKE) to relax the quasi-equilibrium closure of the Arakawa-Schubert cumulus parameterization. A parameter, alpha, is used to relate the CKE to the cumulus mass flux. This parameter is expected to vary with cloud depth, mean shear, and the level of convective activity, but up to now a single constant value for all cloud types has been used. The results of the present study show clearly that this approach cannot yield realistic simulations of both the diurnal cycle and the monthly mean climate state. Improved results are obtained using a version of the model in which alpha is permitted to vary with cloud depth.

Lin, Xin↗
NASA NTRS1997

A Model For the Limiting Time in Vortex Ring Formation

In another presentation, Gharib et at provide experimental results to show that when a vortex ring is created from a pipe by a piston, there is a limiting time or piston stroke length beyond which multiple rings appear. This time appeared to be insensitive to piston velocity history and Reynolds number. Nature might exploit such a. limit in different contexts to coherently deliver mass or momentum flux with the least number of strokes. Here, a simple hypothesis is considered: the limiting time occurs when the apparatus is no longer able to deliver energy at a rate compatible with the requirement, due to Kelvin, that a steady vortex ring have maximum energy given circulation and impulse. More specifically, the limit is expected to occur when the quantity alpha = E/square root of Gamma(sup 3)I delivered by the piston drops below the value, alpha(sub lim) for a limiting steady vortex ring solution. The resulting predictions agree very well with the experiments (after using alpha(sub lim) measured using the experimental flow fields). The insensitivity to piston history also emerges from the model. Finally, piston histories are designed that may extend the limiting time somewhat.

Shariff, Karim↗
NASA NTRS2003

Elastic-Plastic Thermal Stress Analysis of a High-Pressure Cryogenic Storage Tank

The thermal stresses on a cryogenic storage tank contribute strongly to the state of stress of the tank material and its ability to withstand operational stresses. These thermal stresses also affect the growth of any surface damage that might occur in the tank walls. These stresses are particularly of concern during the initial cooldown period for a new tank placed into service, and during any subsequent thermal cycles. A previous preliminary elastic analysis showed that the thermal stress on the inner wall would reach approximately 1,000MPa (145,000 psi). This stress far exceeds the ASTM specified room temperature values for both yield (170MPa) and ultimate (485 MPa) strength for 304L stainless steel. The present analysis determines the thermal stresses using an elastic-plastic model. The commercial software application ANSYS was used to determine the transient spatial temperature profile and the associated spatial thermal stress profiles in a segment of a thick-walled vessel during a typical cooldown process. A strictly elastic analysis using standard material properties for 304L stainless steel showed that the maximum thermal stress on the inner and outer walls was approximately 960 MPa (tensile) and - 270 MPa (compressive) respectively. These values occurred early in the cooldown process, but at different times, An elastic-plastic analysis showed significantly reducing stress, as expected due to the plastic deformation of the material. The maximum stress for the inner wall was approximately 225 MPa (tensile), while the maximum stress for the outer wall was approximately - 130 MPa (compressive).

Barker, J. Mark↗
NASA NTRS2005

Scramjet Engine Flowpath Development for the Hyper-X Mach 10 Flight Test

The third flight of the Hyper-X Research Vehicle at nearly Mach 10 in November 2004 demonstrated the potential for airbreathing propulsion at hypersonic speeds. The flowpath of the scramjet engine used in the Hyper-X Research Vehicle was developed using computational fluid dynamic based design method in combination with a systematic series of ground tests in the NASA HyPulse Shock Tunnel at conditions duplicating Mach 10 flight. The test model was a true scale height and length of the internal flight engine flowpath that was partial width and truncated fore and aft. Tests were conducted using a mixture of hydrogen augmented with two-percent silane. Silane gas served as an ignition aid during the short duration of the pulse facility tests. The engine inflow values of pressure, temperature, and Mach number were parametrically varied during the ground test entries to broaden the database over the expected uncertainty in the flight conditions. A review of the ground test technique and comparisons of the ground test pressures along with selected data from the third flight are presented.

Rogers, R. C.↗
NASA NTRS2001

PacRIM II: A review of AirSAR operations and system performance

In this paper we briefly review the AirSAR system, its expected performance, and quality of data obtained during that mission. We discuss the system hardware calibration methodologies, and present quantitative performance values of radar backscatter and interferometric height errors (random and systematic) from PACRIM II calibration data.

PacRIM II AirSAR radar remote-sensing↗
NASA NTRS2012

Developing Culture-Adaptive Competency Through Experiences with Expressive Avatars

Modern Warfighters often find themselves in a variety of non-combat roles such as negotiator, peacekeeper, reconstruction, and disaster relief. They are expected to perform these roles within a culture alien to their own. Each individual they encounter brings their own set of values to the interaction that must be understood and reconciled. To navigate the human terrain of these complex interactions, the Warfighter must not only consider the specifics of the target culture, but also identify the stakeholders, recognize the influencing cultural dimensions, and adapt to the situation to achieve the best possible outcome. Vcom3D is using game-based scenarios to develop culturally adaptive competency. The avatars that represent the stakeholders must be able to portray culturally accurate behavior, display complex emotion, and communicate through verbal and non-verbal cues. This paper will discuss the use of emerging game technologies to better simulate human behavior in cross-cultural dilemmas. Nomenclature: culture, adaptive, values, cultural values dimensions, dilemmas, virtual humans, non-verbal communications

Silverglate, Daniel S.↗
NASA NTRS2014

Constraints on the Progenitor System of the Type Ia Supernova 2014J from Pre-Explosion Hubble Space Telescope Imaging

We constrain the properties of the progenitor system of the highly reddened Type Ia supernova (SN Ia) 2014J in Messier 82 (M82; d (is) approx. 3.5 Mpc). We determine the supernova (SN) location using Keck-II K-band adaptive optics images, and we find no evidence for flux from a progenitor system in pre-explosion near-ultraviolet through near-infrared Hubble Space Telescope (HST) images. Our upper limits exclude systems having a bright red giant companion, including symbiotic novae with luminosities comparable to that of RS Ophiuchi. While the flux constraints are also inconsistent with predictions for comparatively cool He-donor systems (T (is) approximately 35,000 K), we cannot preclude a system similar to V445 Puppis. The progenitor constraints are robust across a wide range of RV and AV values, but significantly greater values than those inferred from the SN light curve and spectrum would yield proportionally brighter luminosity limits. The comparatively faint flux expected from a binary progenitor system consisting of white dwarf stars would not have been detected in the pre-explosion HST imaging. Infrared HST exposures yield more stringent constraints on the luminosities of very cool (T (is) less than 3000 K) companion stars than was possible in the case of SN Ia 2011fe.

RS Ophiuchi↗
NASA NTRS2015

Spatiotemporal Coherence of Mean and Extreme Aerosol Particle Events over Eastern North America as Observed from Satellite

Quantifying spatiotemporal scales of coherence and variability of aerosol particle properties provides (i) metrics for evaluating observational data sets and model simulations, (ii) inferences regarding dominant causes of variability, and (iii) information that is necessary to determine their climate forcing and air quality impacts. Accordingly, analyses of columnar aerosol optical depth (AOD) and Ångstrom exponent (AE) from the MODerate resolution Imaging Spectroradiometer (MODIS) on the Aqua and Terra satellites, and AErosol RObotic NETwork (AERONET) stations are used to evaluate the spatially averaged (Level-3) MODIS products, and to characterize the spatiotemporal scales of variability (and coherence) of aerosol particles over eastern North America (2000-2013). Results show a high degree of consistency in AOD retrievals from the different data sets but larger discrepancies in AE estimates, highest mean AOD and lowest day-to-day variability during the summer, and largest scales of spatial coherence in summer and fall. Consistent with the scales of spatial coherence from MODIS data, in both data sets power spectra indicate AOD variability is manifest primarily on synoptic and annual time scales. Conversely, AE variability in MODIS data is primarily focused on seasonal, semiannual, and annual time scales, and there is an additional mode of AE variability at approx. 30 days in the AERONET measurements. The frequency of cooccurrence of extreme AOD values (>local 90th percentile) decreases to below 50% at approx. 150 km from a central grid cell, but is above that expected by random chance over almost all of eastern North America, indicating supra-regional scale extreme events.

MODIS↗