SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The configuration of the user transponder on the Tracking and Data Relay satellite is described. The subjects discussed are: (1) transponder concepts and trades, (2) ground station design, (3) antenna configurations for ground equipment, (4) telemetry facilities, (5) signal categories, and (6) satellite tracking.
The appendices to support the data involved in the design and development of the Tracking and Data Relay satellite are presented. The subjects discussed are: (1) spacecraft structural body shapes, (2) antenna configurations, (3) solar configurations, (4) telemetry equipment, and (5) reliability design practices.
An investigation has been conducted in the Langley full-scale tunnel to determine the performance and static stability and control characteristics of a four-engine, upper surface blown jet-flap powered-lift configuration with a swept wing. The investigation included test performed over a range of angle of attack (-4 deg to 36 deg), angle of sideslip (-5 deg to 5 deg), and thrust coefficients (0 to 4.32) for both symmetric and engine-out power conditions and for horizontal and vertical tails both on and off. In addition to the four-engine tests, a few tests were made with the outboard engines removed to simulate a twin-engine powered-lift transport configuration.
A preliminary shielding analysis was carried out for a conceptual nuclear electric propulsion vehicle designed to transport payloads from low earth orbit to synchronous orbit. The vehicle employed a thermionic nuclear reactor operating at 1575 kilowatts and generated 120 kilowatts of electricity for a round-trip mission time of 2000 hours. Propulsion was via axially directed ion engines employing 3300 pounds of mercury as a propellant. The vehicle configuration permitted a reactor shadow shield geometry using LiH and the mercury propellant for shielding. However, much of the radioactive NaK reactor coolant was unshielded and in close proximity to the power conditioning electronics. An estimate of the radioactivity of the NaK coolant was made and its unshielded dose rate to the power conditioning equipment calculated. It was found that the activated NaK contributed about three-fourths of the gamma dose constraint. The NaK dose was considered a sufficiently high fraction of the allowable gamma dose to necessitate modifications in configuration.
Experimental aerodynamic investigations were conducted during mid-July, 1973 on a .004 scale model of the Rockwell International integrated configuration Space Shuttle Vehicle 3. The purpose of the tests was three fold: (1) to determine the static stability characteristics of the integrated vehicle, utilizing the Vehicle 3 orbiter configuration; (2) to determine the effect of interstage structure and tank external fuel lines on the integrated vehicle aerodynamic characteristics; (3) to determine the effects of the aft interstage structure on orbiter aerodynamic loads. Data were recorded on the integrated vehicle (test no. 579) at angles of attack and sideslip ranging from -10 deg to 10 deg over a Mach number schedule from 0.6 to 4.96. Data were obtained on the orbiter alone in the presence of the external tank with SRB attached (test no. 580) at angles of attack from -10 deg to 10 deg over a Mach number range from .6 to 1.96. Plotted data are presented in the body axis system.
The low-speed characteristics of a large-scale model of the F-14A aircraft were studied in tests conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel. The primary purpose of the present tests was the determination of lateral-directional stability levels and control effectiveness of the aircraft in its high-lift configuration. Tests were conducted at wing angles of attack between minus 2 deg and 30 deg and with sideslip angles between minus 12 deg and 12 deg. Data were taken at a Reynolds number of 8.0 million based on a wing mean aerodynamic chord of 2.24 m (7.36 ft). The model configuration was changed as required to show the effects of direct lift control (spoilers) at yaw, yaw angle with speed brake deflected, and various amounts and combinations of roll control.
Some of the mutual aircraft afterbody and engine nozzle interferences that can exist on aircraft complex aft-ends and on simplified twin-jet afterbodies are reviewed. Emphasis is placed on studies of twin-engine fuselage configurations with nozzles installed near the terminus of the afterbody where the interactions of the nozzle exhausts and external stream produce a complex flow-field environment. The magnitude of the aft-end problem for real aircraft configurations is illustrated, and some theoretical and empirical considerations of afterbody drag on simple bodies are treated. Many of the factors regarding airframe-installation effects on nozzle performance are discussed, as well as nozzle-installation effects on aircraft performance.
Aerodynamic force and moment tests were conducted on an 0.015-scale space shuttle vehicle configuration 140A/B model (49-0) in a transonic pressure tunnel. The test was carried out at Mach numbers 0.35, 0.60, 0.80, 0.90, 0.98, and 1.20, and at Reynolds numbers ranging from 1.90 million per foot to 3.97 million per foot, depending on tunnel total pressure capability and model structural limits. The model attitude was varied in angle-of-attack from minus 2 deg to +22 deg at 0 deg and 5 deg angles of yaw, and in angle-of-sidelip from minus 5 to +10 deg at 0 deg, 7.5 deg, and 15 deg angles of pitch. The purpose of this test was to establish and verify longitudinal and lateral-directional characteristics of the 140A/B Configuration Orbiter and to determine the effects of surface deflections on vehicle performance, stability, and control.
A study aimed at the implementation of a configuration management flight control system is reported. The system is designed to take the guesswork out of, and improve the operational safety of, transition flight in the region from cruise to STOL. Potential improvements in the trim configuration management aspects of the transition process are described.
Performance, stability, and control tests at supersonic and hypersonic speeds have been performed on two versions of a shuttle orbiter configuration designed for reduced length. One of the test configurations had twin dorsal fins rolled out 15 deg the other a centerline single dorsal fin. Effects of elevon and body deg flap deflection, rudder flare, planform fillet, and aileron deflection were examined. The supersonic tests were over the Mach number range from 1.6 to 4.63 at a Reynolds number based on model length of 4,300,000. The hypersonic tests were conducted at a Mach number of 10.3 and Reynolds number of 670,000.
The development of flight-control facilities for the Apollo program is reviewed from the viewpoint of the user organization. These facilities are treated in three categories: data systems, ground-based display and control systems, and configuration management. The effects of certain Apollo program factors on the selection, sizing, and configuration management of these systems are discussed. Recommendations are made regarding improvement of the systems and the reduction of system sensitivity to the program factors.
The effect of plume-induced flow separation and aspiration effects due to operation of both orbiter and the solid rocket motors on a 0.019-scale model of the launch configuration of the Space Shuttle Vehicle is determined. Longitudinal and lateral-directional stability data were obtained at Mach numbers of 1.6, 2.0, and 2.2 with and without the engines operating. The plumes exiting from the engines were simulated by a cold-gas jet supplied by an auxiliary 200-atm air supply system and solid-body plume simulators. The aerodynamic effects produced by these two simulation procedures are compared. The parameters most significantly affected by the jet plumes are pitching moment, elevon control effectiveness, axial force, and orbiter wing loads. The solid rocket motor (SRM) plumes have the largest effect on the aerodynamic characteristics. The effect of the orbiter plumes in combination with the SRM plumes is also significant. Variations in the nozzle design parameters and configuration changes can reduce the jet plume-induced aerodynamic effects.
Data obtained from the wind tunnel tests of a scale model of the space shuttle orbiter configuration 140 A/B are presented. The test was conducted at Mach numbers of 2.5, 3.9, and 4.6 with Reynolds numbers from 1.25 million per foot to 5.0 million per foot. Various control surface settings were used ranging from an angle of attack range from minus 4 to plus 42 degrees at zero angle of yaw. Longitudinal stability and control characteristics of the space shuttle configuration were analyzed.
Tests were conducted in the NASA/ARC 6- by 6-foot transonic wind tunnel from September 12 to September 28, 1973 on an 0.015-scale model of the space shuttle configuration 140 A/B. Surface pressure data were obtained for the orbiter for both launch and entry configuration at Mach numbers from 0.6 to 2.0. The surface pressures were obtained in the vicinity of the cargo bay door hinge and parting lines, the side of the fuselage at the crew compartment and below the OMS pods at the aft compartment. Data were obtained at angles of attack and sideslip consistent with the expected divergencies along the nominal trajectory. These tests were first in a series of tests supporting the orbiter venting analysis. The series will include tests in three facilities covering a total Mach number range from 0.6 to 10.4.
Supersonic aerodynamic tests were conducted in the NASA/LaRC Unitary Plan Wind Tunnel on a 0.015-scale model of the Space Shuttle Vehicle 4 configuration. Surface pressure data were obtained for both the launch (test IA35) and entry (test OA64) configurations at Mach numbers from 2.5 to 4.5. The surface pressure was measured in the vicinity of the cargo bay door hinge and parting lines and on the side of the fuselage at the crew compartment and below the OMS pods at the aft compartment. Data were obtained for angles of attack and sideslip consistent with the expected excursions about the nominal trajectory values at the test Mach numbers. These tests were a part of a test series supporting the orbiter venting analysis over a Mach number range from 0.6 to 10.4
The primary objective of the test was to obtain stability and control data for the basic configuration and an alternate configuration for the Space Shuttle Orbiter. Pitch runs were made with 0 deg of sideslip at Mach numbers of 5.3, 7.3 and 10.3. Six-component force data and fuselage base pressures were recorded for each run. Shadowgraph pictures were taken at selected points. Model 420 was used for the tests.
The results of a wind tunnel test to determine the force, moment, and hinge-moment characteristics of the Configuration 2A Space Shuttle Vehicle Orbiter at Mach numbers 5, 7 and 10 are presented. The model was an 0.015-scale representation of the Orbiter Configuration 2A used in test 0A11A and later tests. Six-component aerodynamic force and moment data were recorded from a 1.50-inch internal strain-gage balance, and base pressures were taken for axial and drag force corrections. Hinge-moment data were obtained for the rudder and the inboard and outboard elevon panels of the starboard wing.
An investigation has been conducted to determine the effects of configuration variables on the lateral-directional stability characteristics of a wing-fuselage configuration. The variables under study included variations in the location of a single center-line vertical tail and twin vertical tails, wing height, fuselage strakes, and horizontal tails. The study was conducted in the Langley high-speed 7-by 10-foot tunnel at a Mach number of 0.30, at angles of attack up to 44 deg and at sideslip angles of 0 deg and plus or minus 5 deg.