SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Self-alining slide assembly improves air flow. Alinement accuracy is incorporated into assembly at time of fabrication, reducing requirement for mounting-hole location accuracy. Amount of labor needed for installation, necessary machining, hardware, and number of mounting points are reduced from previous support system. Load-bearing capability is built into mounting platform.
A systematic investigation of the drag associated with cooling air flow in contemporary general aviation engine installations is proposed. Theoretical and experimental methods include a state-of-the-art survey, determination of cooling drag by flight tests, and establishment of relative magnitude and components of cooling drag.
The results are presented of a cold-mixing investigation performed to supply combustor design information and to determine optimum normal fuel-injector configurations for a general scramjet swept-strut fuel injector. The experimental investigation was made with two swept struts in a closed duct at a Mach number of 4.4 and a nominal ratio of jet mass flow to air mass flow of 0.0295, with helium used to simulate hydrogen fuel. Four injector patterns were evaluated; they represented the range of hole spacing and the ratio of jet dynamic pressure to free-stream dynamic pressure. Helium concentration, pitot pressure, and static pressure in the downstream mixing region were measured to generate the contour plots needed to define the mixing-region flow field and the mixing parameters. Experimental results show that the fuel penetration from the struts was less than the predicted values based on flat-plate data; but the mixing rate was faster and produced a mixing length less than one-half that predicted.
A 51-cm-diam model of a fan stage for short haul aircraft was tested in a single stage compressor research facility. The rotor blades were set 7 deg toward the axial direction (opened) from the design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed and a weight flow of 30.9 kg/sec, the stage pressure ratio and efficiency were 1.205 and 0.85, respectively. The design speed rotor peak efficiency of 0.90 occurred at a flow rate of 32.5 kg/sec.
A 51-cm-diam model of a fan stage for a short haul aircraft was tested in a single stage-compressor research facility. The rotor blades were set 5 deg toward the axial direction (opened) from design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed of 213.3 m/sec and a weight flow of 31.5 kg/sec, the stage pressure ratio and efficiency were 1.195 and 0.88, respectively. The design speed rotor peak efficiency of 0.91 occurred at the same flow rate.
A perforated tube is housed in a chamber in which vacuum is drawn. An air jet is directed into one end of the tube and fiber bundles are fed into the jet which separates and dispenses individual fibers from the bundle, fluffs them, cleanses them of any particulate material, and carries them into the tube. The tube retains the fibers while fiber fragments, undesirably short fibers and particulate matter are drawn by the vacuum and resultant air flow out of the tube through its perforations to a suitable discharge.
Models and tests on an acoustic duct liner system which has the property of controlled-variable acoustic impedance are described. This is achieved by a novel concept which uses the effect of steady air flow through a multi-layer, locally reacting, resonant-cavity absorber. The scope of this work was limited to a 'proof of concept.' The test of the concept was implemented by means of a small-scale, square-section flow duct facility designed specifically for acoustic measurements, with one side of the duct acoustically lined. The test liners were designed with the aid of previously established duct acoustic theory and a semi-empirical impedance model of the liner system. Over the limited range tested, the liner behaved primarily as predicted, exhibiting significant changes in resistance and reactance, thus providing the necessary concept validation.
A review of meteorological satellites, the instrumentation mounted on them, and uses to which they were put. The history of the development of the system of meteorological satellites is reviewed, followed by detailed coverage of the sensors (imagers, scanners, sounders) mounted on the satellites. Global cloud cover, storm tracking, tropospheric water vapor, stratospheric temperature and air flow, and the radiation budget are among the objects of study in this decade-and-a-half program. Weather analysis and prediction have been advanced appreciably.
A mathematical model for sound transmission into a thin cylindrical shell is used to study sound transmission under flight conditions, i.e., under conditions of external air flow past a pressurized cylinder at flight altitude. Numerical results for different incidence angles are presented for a typical narrow-bodied jet in cruising flight at 10,660 m with interior pressure at 2440 m. A comparison is made between no-flow sound transmission at standard conditions on the ground to sound transmission under flight conditions. It is shown that at M = 0, the cylinder transmission loss (TL) has dips at the cylinder ring frequency (fR) and the critical frequency (fc) for a flat panel of same material and thickness as shell. Between fR and fc, cylinder TL follows a mass-law behavior. Flow provides a modest increase in TL in the mass-law region, and strongly interacts with the cylinder resonances below fR.
A means for attenuating the vortex created at aircraft wingtips which consists of a retractable planar surface transverse to the airstream and attached downstream of the wingtip which creates a positive pressure gradient just downstream from the wing is presented. The positive pressure forces a break up of the rotational air flow of the vortex.
As part of the Energy Research and Development Administration (ERDA) wind energy program, NASA Lewis Research Center is testing an experimental 100-kW wind turbine. Rotor blade and drive shaft loads and tower deflection were measured during operation of the wind turbine at rated rpm. The blade loads measured are higher than anticipated. Preliminary results indicate that air flow blockage by the tower structure probably caused the high rotor blade bending moments.
Materials were assessed and fabrication techniques were developed for use in the manufacture of wing surface materials compatible with the application of both aluminum alloys and nonmetallic composites. The concepts investigated included perforations and slots in the metallic test panels and microporosity and perforations in the composite test panels. Perforations were produced in the metallic test panels by the electron beam process and slots were developed by controlled gaps between the metal sheets. Microporosity was produced in the composite test panels by the resin bleed process, and perforations were produced by the fugitive fiber technique. Each of these concepts was fabricated into test panels, and air flow tests were conducted on the panels.
The rate of odd nitrogen (NOx) production by electrical discharge through air was theoretically and experimentally estimated to be about 60,000 trillion NOx molecules per joule. The theoretical treatment employed a cylindrical shock-wave solution to calculate the rate of NOx production in high temperature reactions. The limits obtained were experimentally verified by subjecting a regulated air flow to electrical discharges followed by a measurement of NOx production using chemiluminescence. These measurements also indicated that water vapor content has no detectable effect on the NOx production rate. The results imply that lightning is a significant source of NOx, producing about 30-40 megatons NOx-N per year and possibly accounting for as much as 50% of the total atmospheric NOx source.
The goal of cooling installation design is to provide adequate cooling air flow to the engine with a minimum drag penalty. To achieve this goal, attention must be given to certain aerodynamic factors involved in the design problem. In the present paper, the factors which influence the aerodynamic design of horizontally-opposed engine cooling installations are discussed with particular reference to the performance of the aircraft in terms of the dynamic pressure generated for the power output of the engine, the gains or losses through the propeller, proper inlet design, altitude effects on the orifice characteristics of the engine, and exit area sizing. Results of a flight research program showed that the inlet design has a significant influence on cooling effectiveness and drag; the inlet should be designed for low velocity ratios and should avoid small radii of curvature in its geometry. The influence of the propeller on the inlet appears to cause the stagnation point on the lip to move toward the inside.
The test article, Model EF-212, Serial Nr. 002, is a single glazed collector with a nonselective absorber plate, using flowing air as the heat transfer medium. The absorber plate and box frame are aluminum and the insulation is one inch isocyanurate foam board with thermal conductivity of 0.11 (BTU/sq ft Hr0/ft.) The tests included the following. (1) time constant test, (2) collector efficiency test, (3) collector stagnation test, (4) incident angle modifier test, (5) load test, (6) weathering test, and (7) absorber plate optical properties test. The results of these tests are tabulated, graphed, or otherwise recorded.
A Lamilloy combustor liner was designed, fabricated and tested in a combustor at pressures up to 8 atmospheres. The liner was fabricated of a three layer Lamilloy structure and designed to replace a conventional step louver liner. The liner is to be used in a combustor that provides hot gases to a turbine cooling test facility at pressures up to 40 atmospheres. The Lamilloy liner was tested extensively at lower pressures and demonstrated lower metal temperatures than the conventional liner, while at the same time requiring about 40 percent less cooling air flow. Tests conducted at combustor exit temperatures in excess of 2200 K have not indicated any cooling or durability problems with the Lamilloy linear.
Polychloroprene flexible foam was evaluated as a reference material for fire toxicity tests. A commercial sample was evaluated using nine different test conditions of the USF methodology. The material exhibited a wide range of relative toxicity depending on the test conditions. Times to incapacitation and times to death were shortest at 16 ml/sec (1 l/min) air flow, at any fixed heating rate and upper limit temperature.
A Lamilloy combustor liner has been designed, fabricated and tested in a combustor at pressures up to 8 atmospheres. The liner was fabricated of a three layer Lamilloy structure and designed to replace a conventional step-louver liner. The liner will be used in a combustor that provides hot gases to a turbine cooling test facility at pressures up to 40 atmospheres. The Lamilloy liner was tested extensively at lower pressures and demonstrated lower metal temperatures than the conventional liner, while at the same time requiring about 40 percent less cooling air flow. Tests conducted at combustor exit temperatures in excess of 2200 K have not indicated any cooling or durability problems with the Lamilloy liner.