SEARCH · Engineering Papers

Results for “AFTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Effect of sweep angles on aerodynamic performance of double arrow wing - An analytical study

Hybrid wing planforms are studied for adoption on supersonic transport and fighter aircraft. The free vortex sheet method is used to determine effects of the leading-edge sweep angles on the aerodynamic performance of a double arrow wing with a strake. Results show lift and drag increase with the increase of the inboard and outboard leading-edge sweep angles. However, the lift-to-drag ratio is little influenced by the changes in these sweep angles. Spanwise surface pressure distributions on the aft region are influenced by the inboard sweep angle while the outboard sweep angle has no effect on these pressures. Finally, the experimental data and predicted results are compared to show good agreement.

Reddy, C. S.↗

NASA NTRS1981

Cartographic potential of a spacecraft line-array camera system - Stereosat

A study of the Stereosat mission, which may acquire analog/digital stereo image data of cartographic quality with linear array camera systems, is presented, with attention given to the Stereosat system and the mission parameters, the utilization of the Stereosat studies in order to indicate the nature and scope of the problems associated with recording image data of high geometric fidelity from spacecraft equipped with line array sensors, and the assessing of the possibilities of meeting the completeness and accuracy requirements of cartographic products. A 713-km circular, sun-synchronous, near polar orbit, with an inclination of 98.24 deg and a repeat cycle of 48 days is designed to insure global coverage of the earth's land masses during the three-year lifetime of the mission. Three cameras (fore, vertical, and aft looking), mounted so as to record stereotriplets for a 61.4 km wide swath at a nominal focal plane scale of 1:1,000,000, are considered. The IFOV of 15 m should be adequate for producing thematic and image maps at scales of 1:50,000 to 1:250,000. The value of the coverage to cartographers will be dictated by the accuracy of the digital image data, which is largely a function of satellite control.

Welch, R.↗

NASA NTRS1981

Turbomachinery noise studies of the AiResearch QCGAT engine with inflow control

The AiResearch Quiet Clean General Aviation Turbofan engine was tested on a vertical lift fan facility to measure the acoustic performance of two inflow control devices (ICD) of similar design, and three inlet lips of different external shape. Far-field directivity patterns calculated by existing analyses were compared with the measured fan fundamental blade passing frequency (BPF/F/) and broadband data. Installing an ICD on an engine with hardwall ducts reduced the BPF(F) tone everywhere in the far-field. When the ICD was installed on an engine with active acoustic panels, tone reduction in the forward quadrant was comparable to that in the hardwall tests; in the aft quadrant, however, tone noise was attenuated by the large acoustic panels in the bypass duct to such a degree that the ICD had little effect. Tests to compare performance of ICDs with hardwall inlet ducts showed only minor differences in the BPF(F) directivity patterns, while broadband noise was the same for both. Forward-quadrant BPF(F) and broadband directivity patterns were found to be similar for the inlet lips tested with a hardwall inlet duct. At high fan speeds, however, the shape of the analytical multimodal tone pattern from the exhaust nozzle was flatter than the measured patterns. The sources of lobes from several propagating single modes found in the forward-quadrant BPF(F) data were attributed to rotor/strut interaction and the rotor-alone pressure field.

Mcardle, J. G.↗

NASA NTRS1953

Effect of Ice and Frost Formations on Drag of NACA 65(sub 1) -212 Airfoil for Various Modes of Thermal Ice Protection

The effects of primary and. runback icing and frost formations on the drag of an 8-foot-chord NACA 651-212 airfoil section were investigated over a range of angles of attack from 20 to 80 and airspeeds up to 260 miles per hour for icing conditions with liquid-water contents ranging from 0.25 to 1.4 grams per cubic meter and datum air temperatures of -30 to 30 F. The results showed that glaze-ice formations, either primary or runback, on the upper surface near the leading edge of the airfoil caused large and rapid increases in drag, especially at datum air temperatures approaching 32 F and in the presence of high rates of water catch. Ice formations at lower temperatures (rime ice) did not appreciably increase the drag coefficient over the initial (standard roughness) drag coefficient. Cyclic de-icing of the primary Ice formations on the airfoil leading-edge section permitted the drag coefficient to return almost to the bare airfoil drag value. Runback icing on the lower surface did not present a serious drag problem except when heavy spanwise ridges of runback ice occurred aft of the heatable area. Frost formations caused rapid and large increases in drag with incipient stalling of the airfoil.

Gray, V. H.↗

NASA NTRS1951

Effectiveness of Thermal-Pneumatic Airfoil-Ice-Protection System

Icing and drag investigations were conducted in the NACA Lewis icing research tunnel employing a combination thermal-pneumatic de-icer mounted on a 42-inch-chord NACA 0018 airfoil. The de-icer consisted of a 3-inch-wide electrically heated strip symmetrically located about the leading edge with inflatable tubes on the upper and lower airfoil surfaces aft of the heated area. The entire de-icer extended to approximately 25 percent of chord. A maximum power density of 9.25 watts per square inch was required for marginal ice protection on the airfoil leading edge at an air temperature of 00 F and an airspeed of 300 miles per hour. Drag measurements indicated, that without icing, the de-icer installation increased the section drag to approximately 140 percent of that of the bare airfoil; with the tubes inflated, this value increased to a maximum of approximately 620 percent. A 2-minute tube-inflation cycle prevented excessive ice formation on the inflatable area although small scattered residual Ice formations remained after inflation and were removed intermittently during later cycles. Effects of the time lag of heater temperatures after initial application of power and the insulating effect of ice formations on heater temperatures were also determined.

Gowan, William H., Jr.↗

NASA NTRS1981

Wind-tunnel results for a modified 17-percent-thick low-speed airfoil section

Wind-tunnel tests were conducted in the Langley low-turbulence pressure tunnel to evaluate the effects on performance of modifying a 17-percent-thick low-speed airfoil. The airfoil contour was altered to reduce the pitching-moment coefficient by increasing the forward loading and to increase the climb lift-drag ratio by decreasing the aft upper surface pressure gradient. The tests were conducted over a Mach number range from 0.07 to 0.32, a chord Reynolds number range 1.0 x 10 to the 6th power to 12.0 x 10 to the 6th power, and an angle-of-attack range from about -10 deg to 20 deg.

Mcghee, R. J.↗

NASA NTRS1981

Pressure distributions and shock shapes for 12.84 deg/7 deg on-axis and bent-nose biconics in air at Mach 6

Pressure distributions and shock shapes on a spherically blunted, 12.84 deg /7 deg on axis biconic and a spherically blunted, 12.84 deg/7 deg bent nose biconic at Mach 6 in air were measured. The angle of attack, referenced to the axis of aft cone, was varied from 0 deg to 25 deg in nominal 5 deg increments. Two values of free stream Reynolds number based on model length were tested. Predictions from simple, theories and from a supersonic, three dimensional, external invsicid code (STEIN) are compared with measured values. Predicted STEIN shock shapes and windward pressures are in agreement with measured values for both biconics over the present range of angle of attack.

Miller, C. G., III↗

NASA NTRS1981

Comparison of two parallel/series flow turbofan propulsion concepts for supersonic V/STOL

The thrust, specific fuel consumption, and relative merits of the tandem fan and the dual reverse flow front fan propulsion systems for a supersonic V/STOL aircraft are discussed. Consideration is given to: fan pressure ratio, fan air burning, and variable core supercharging. The special propulsion system components required are described, namely: the deflecting front inlet/nozzle, the aft subsonic inlet, the reverse pitch fan, the variable core supercharger and the low pressure forward burner. The potential benefits for these unconventional systems are indicated.

Luidens, R. W.↗

NASA NTRS1981

Study of liquid slosh in the tracking and data relay satellite hydrazine tanks

An experimental study was conducted to provide data for evaluation of the parameters for an analytical mechanical model representation of liquid/interface dynamics in the TDRSS propellant tanks. Models were developed for two liquid-under ullage (forward tank) configurations and for one liquid-over-ullage (aft tank) configuration. However, additional test runs were conducted with liquids of different densities in both cases to allow separation of bladder stiffness and gravity effects under various simulated steady acceleration conditions. Both static and dynamic parameters are evaluated to provide a good prediction of observed results.

Kana, D. D.↗

NASA NTRS1982

CF6 Jet Engine Diagnostics Program: High pressure compressor clearance investigation

The effects of high pressure compressor clearance changes on engine performance were experimentally determined on a CF6 core engine. The results indicate that a one percent reduction in normalized average clearance, expressed as a fraction of airfoil length, improves compressor efficiency by one percent. Compressor clearances are reduced by the application of rotor bore cooling, insulation of the stator casing, and use of a low coefficient of expansion material in the aft stages. This improvement amounts to a reduction of normalized average clearance of 0.78 percent, relative to CF6-60 compressor, which is equivalent to an improvement in compressor efficiency of 0.78 percent.

Radomski, M. A.↗

NASA NTRS1982

A preliminary comparison between the SR-3 propeller noise in flight and in a wind tunnel

The noise generated by supersonic-tip-speed propellers is addressed. Models of such propellers were tested for acoustics in the Lewis 8-by-6-foot wind tunnel. One of these propeller models, SR-3, was tested in flight on the Jetstar airplane and noise data were obtained. Preliminary comparisons of the maximum blade passing tone variation with helical tip Mach number taken in flight with those taken in the tunnel showed good agreement when corrected to the same test conditions. This indicated that the wind tunnel is a viable location for measuring the noise of these propeller models. Comparisons of the directivities at 0.6 and 0.7 axial Mach number showed reasonable agreement. At 0.75 and 0.8 axial Mach number the tunnel directivity data fell off more towards the front than did the airplane data. A possible explanation for this is boundary layer refraction which could be different in the wind tunnel from that in flight. This may imply that some corrections should be applied to both the airplane and wind tunnel data at the forward angles. At and aft of the peak noise angle the boundary layer refraction does not appear to be significant and no correction appears necessary.

Dittmar, J. H.↗

NASA NTRS1981

Development and demonstration of manufacturing processes for fabricating graphite/LARC 160 polyimide structural elements

The development and demonstration of manufacturing technologies for the structural application of Celion graphite/LARC-160 polyimide composite material is discussed. Process development and fabrication of demonstration components are discussed. Process development included establishing quality assurance of the basic composite material and processing, nondestructive inspection of fabricated components, developing processes for specific structural forms, and qualification of processes through mechanical testing. Demonstration components were fabricated. The demonstration components consisted of flat laminates, skin/stringer panels, honeycomb panels, chopped fiber compression moldings, and a technology demonstrator segment (TDS) representative of the space shuttle aft body flap.

Frost, R. K.↗

NASA NTRS1982

Solid rocket booster water impact test

Water impact drop tests were performed on the space shuttle solid rocket boosters (SRB). Peak water impact pressures and pressure/time traces were measured for various impact velocities using a two-dimensional, full-scale SRB aft skirt internal ring model. Passive burst disc-type pressure transducers were calibrated for use on flight SRB's. The effects on impact pressure of small ring configuration changes and application of thermal protection system cork layers were found to be negligible.

Bugg, F.↗

NASA NTRS1982

Solar drum positioner mechanisms

The need for additional power on spinning satellites required development of deployable solar arrays activated, as on a 3-axis vehicle, after separation from a booster or shuttle orbiter. Mechanisms were developed for telescopically extending a secondary 36.3 kg (80 lb.), 2.13 m (84 in.) diameter spinning solar drum for a distance of 2.0 m (80 in.) or more along the spin axis. After extension, the system has the capability of dynamically controlling the drum tilt angle about the spin axis to provide precision in-orbit balancing of the spacecraft. This approach was selected for the SBS, ANIK C, ANIK D, WESTAR B and PALAPA B satellites. It was successfully demonstrated during the in orbit deployment of the aft solar panels of the SBS F-3 and F-1 satellites, subsequent to the November 1980 and September 1981 launches.

Briggs, L. W.↗

NASA NTRS1982

Develop, demonstrate, and verify large area composite structural bonding with polyimide adhesives

The technology required to produce graphite-polyimide structural components with operational capability at 598 K (600 F) is considered. A series of polyimide adhesives was screened for mechanical and physical properties and processibility in fabricating large midplane bonded panels and honeycomb sandwich panels in an effort to fabricate a structural test component of the space shuttle aft body flap. From 41 formulations, LaRC-13, FM34B-18, and a modified LaRC-13 adhesive were selected for further evaluation. The LaRC-13 adhesive was rated as the best of the three adhesives in terms of availability, cost, processibility, properties, and ability to produce void fee large area (12" x 12") midplane bonds. Surface treatments and primers for the adhesives were evaluated and processes were developed for the fabrication of honeycomb sandwich panels of very good quality which was evidenced by rupture in the honeycomb core rather than in the facesheet bands on flatwise tensile strength testing. The fabrication of the adhesively bonded honeycomb sandwich cover panels, ribs, and leading edge covers of Celion graphite/LARC-160 polyimide laminates is described.

Bhombal, B. D.↗

NASA NTRS1981

Satellite services system analysis study. Volume 4: Service equipment concepts

Payload deployment equipment is discussed, including payload separation, retention structures, the remote manipulator system, tilt tables, the payload installation and deployment aid, the handling and positioning aid, and spin tables. Close proximity retrieval, and on-orbit servicing equipment is discussed. Backup and contingency equipment is also discussed. Delivery and retrieval of high-energy payloads are considered. Earth return equipment, the aft flight deck, optional, and advanced equipment are also discussed.

Source record↗

NASA NTRS1982

STS-3 main parachute failure

A failure analysis of the parachute on the Space Transportation System 3 flight's solid rocket booster's is presented. During the reentry phase of the two Solid Rocket Boosters (SRBs), one 115 ft diameter main parachute failed on the right hand SRB (A12). This parachute failure caused the SRB to impact the Ocean at 110 ft/sec in lieu of the expected 3 parachute impact velocity of 88 ft/sec. This higher impact velocity relates directly to more SRB aft skirt and more motor case damage. The cause of the parachute failure, the potential risks of losing an SRB as a result of this failure, and recommendations to ensure that the probability of chute failures of this type in the future will be low are discussed.

Runkle, R.↗

NASA NTRS1980

Integrated application of active controls (IAAC) technology to an advanced subsonic transport project. Initial ACT configuration design study

The initial ACT configuration design task of the integrated application of active controls (IAAC) technology project within the Energy Efficient Transport Program is summarized. A constrained application of active controls technology (ACT) resulted in significant improvements over a conventional baseline configuration previously established. The configuration uses the same levels of technology, takeoff gross weight, payload, and design requirements/objectives as the baseline, except for flying qualities, flutter, and ACT. The baseline wing is moved forward 1.68 m. The configuration incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 45% reduction in horizontal tail size), lateral/directional-augmented stability, an angle of attack limiter, wing load alleviation, and flutter mode control. This resulted in a 930 kg reduction in airplane operating empty weight and a 3.6% improvement in cruise efficiency, yielding a 13% range increase. Adjusted to the 3590 km baseline mission range, this amounts to 6% block fuel reduction and a 15.7% higher incremental return on investment, using 1978 dollars and fuel cost.

Source record↗