SEARCH · Engineering Papers

Results for “use cases”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

All sources NASA NTRS DOE OSTI

NASA NTRS2000

Calculation of TIR Canopy Hot Spot and Implications for Earth Radiation Budget

Using a 3-D model for thermal infrared exitance and the Lowtran 7 atmospheric radiative transfer model, we compute the variation in brightness temperature with view direction and, in particular, the canopy thermal hot spot. We then perform a sensitivity analysis of surface energy balance components for a nominal case using a simple SVAT model given the uncertainty in canopy temperature arising from the thermal hot spot effect. Canopy thermal hot spot variations of two degrees C lead to differences of plus or minus 24% in the midday available energy.

Smith, J. A.↗

NASA NTRS2015

Measured Polarized Spectral Responsivity of JPSS J1 VIIRS Using the NIST T-SIRCUS

Recent pre-launch measurements performed on the Joint Polar Satellite System (JPSS) J1 Visible Infrared Imaging Radiometer Suite (VIIRS) using the National Institute of Standards and Technology (NIST) Traveling Spectral Irradiance and Radiance Responsivity Calibrations Using Uniform Sources (T-SIRCUS) monochromatic source have provided wavelength dependent polarization sensitivity for select spectral bands and viewing conditions. Measurements were made at a number of input linear polarization states (twelve in total) and initially at thirteen wavelengths across the bandpass (later expanded to seventeen for some cases). Using the source radiance information collected by an external monitor, a spectral responsivity function was constructed for each input linear polarization state. Additionally, an unpolarized spectral responsivity function was derived from these polarized measurements. An investigation of how the centroid, bandwidth, and detector responsivity vary with polarization state was weighted by two model input spectra to simulate both ground measurements as well as expected on-orbit conditions. These measurements will enhance our understanding of VIIRS polarization sensitivity, improve the design for future flight models, and provide valuable data to enhance product quality in the post-launch phase.

JPSS↗

NASA NTRS2018

The Behavior, Constraint, and Scenario (BeCoS) Tool: A Web-Based Software Application for Modeling Behaviors and Scenarios

The Behavior, Constraint, and Scenario (BeCoS) tool has been developed to allow engineers to specify system and component behaviors. The tool is a web application that is developed in JavaScript and uses the React framework for the user interface and Redux for maintaining application state. The foundation of the tool is its underlying ontology, which expands upon a previously-defined behavior ontology with a scenario ontology. The behavior ontology includes elements like behaving elements, state variables, parameters, and constraints, while the scenario ontology includes core constructs like activities, temporal constraints, and timepoints. BeCoS allows users to easily create behaving elements and to specify their state variables, parameters, state machines, and constraints. BeCoS also allows users to develop temporal constraint networks that specify constraints on component states over time. BeCoS is a prototype tool that has been deployed and tested by systems engineers on the Europa Clipper project, which generated several use cases and helped steer its current developmental effort. By enabling systems engineers to specify behavior in a semantically-rigorous manner, BeCoS is an enabling technology for analyses that previously could not be performed, and when exporting its model to other tools, allows for consistent behavior models to be used.

Ingham, Michel D.↗

NASA NTRS2018

The Behavior, Constraint, and Scenario (BeCoS) Tool: A Web-Based Software Application for Modeling Behaviors and Scenarios

Inghams, Michel D.↗

DOE OSTI2020

Sparse thermal data for cellular automata modeling of grain structure in additive manufacturing

Grain growth in the wake of the melt pool formed during alloy-based additive manufacturing (AM) is complex and multifaceted, depending on parameters governing heat transport, fluid flow, and solidification itself. Cellular automata (CA) models have proven effective in providing computationally efficient and physically sound predictions of grain structure for several AM problems, but their efficiency is tied to the performance of heat transport models. CA models use only a small portion of the problem's temperature data (near the moving melt pool boundary), and much of the CA calculations do not affect the final result due to re-melting of material. Coupling of and communication between heat transport and solidification models, and eliminating operations irrelevant towards final grain structure prediction, will be necessary for using these methods for efficient simulation of large parts. In this work, we introduce a procedure of decoupling the CA from temperature field simulation, using files of relevant temperature data written by the heat transport model. This approach is validated against the standard coupling approach using data obtained through the computational fluid dynamics software OpenFOAM. Negligible differences are seen in grain size, volume, and texture distributions for multilayer simulation of test problems, while the quantity of temperature data for these test problems was reduced by four orders of magnitude (from 100s of GB to 10s of MB) and the code performance sped up by a factor of around 50. Furthermore, variability in microstructure as a function of cell size, substrate, time step, and nucleation parameters is studied, and it is found that cell sizes less than or equal to 1.67 μm and sufficiently small time steps yield Αstatistically equivalent microstructures. Finally, a potential use case for this CA approach—the layer-wise convergence in grain structure starting from extremes in initial grain size—is examined. This approach's ability to simulate expected trends in nucleation and epitaxial grain growth for large regions of microstructure, simulated independently of heat transport models themselves, should prove useful for investigation of various microstructure uncertainties and prediction of part-scale experimental results.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Synchronized Waveforms – A Frontier of Data-Based Power System and Apparatus Monitoring, Protection, and Control

Voltage and current waveforms contain the most authentic and granular information on the behaviors of power systems. In recent years, it has become possible to synchronize waveform data measured from different locations. Thus large-scale coordinated analyses of multiple waveforms over a wide area are within our reach. This development could unleash a set of new concepts, strategies, and tools for monitoring, protecting, and controlling power systems and apparatuses. This paper presents an in-depth review and analysis of the advancements in synchronized waveform data, including measurement devices, data characteristics, use cases, and comparisons with synchrophasor data. Based on the findings, five strategies are proposed to discover and develop synchronized waveform based applications over multiple application areas. The paper also presents three complementary measurement platforms and two data screening algorithms for application implementation. It further discusses committee activities and standard developments useful to explore the full potential of the data.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2022

On the Importance of Using Event-Specific Wave Diffusion Rates in Modeling Diffuse Electron Precipitation

A few to tens of keV electron precipitation that carries substantial energy source down to the upper atmosphere to create aurora is manifested as an important magnetosphere-ionosphere coupling process. The precipitation is usually caused by scattering processes associated with plasma waves in the magnetosphere. The scattering process is often quantified by wave diffusion rates that indicate how fast an electron is scattered. Global models commonly use diffusion coefficients that are derived from statistical wave models. However, due to the statistical nature, many localized, transient features could be smeared out. In this study, we investigate electron precipitation using event-specific diffusion coefficients that are obtained based on simultaneous in-situ measured/inferred, rather than statistical, chorus wave dynamics. We find that the application of the event-specific diffusion coefficients associated with a more dynamic and intense chorus wave model leads more electrons, particularly at several to tens of keV in the dawn-to-noon sector at L > 3, to precipitate than using statistical coefficients. Here, the new simulation roughly captures both the intensity and variability of the precipitating flux as detected by the NOAA/POES satellites. Ionospheric electron density in the lower E region (100–120 km) observed by the mid-latitude Millstone Hill radar is also much better reproduced, while the case using statistical diffusion coefficients underestimates the ionization rate. This study implies the importance of using event-specific diffusion rates in simulating the diffuse electron precipitation and understanding the magnetosphere-ionosphere coupling.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1976

Study leading to the refinement of the SRB structural analysis program

The constructed SRB math model was used for the analysis of the 85/32/5(VV/VH/theta) cavity collapse load condition for the aft end of the SRB structure. Linear, nonlinear collapse and bifurcation buckling analyses were performed. The linear and bifurcation buckling analyses showed that structural integrity and positive margins of safety are maintained for the applied maximum load case using a design factor of 1.25. The nonlinear collapse analysis predicts stresses in the skirt above the yield for a load factor of 1.0. Applying the 1.25 design factor gives a negative margin of safety against the material ultimate. The predicted collapse occurs at a load factor higher than 1.25.

Jones, W. E.↗

NASA NTRS1993

The Clementine instrument complement

The recent successes of the Galileo solid-state imaging (SSI) experiment at the Moon and Gaspra show the utility of multispectral imaging of planetary objects. 'Clementine' is the planetary community's 'code name' for the SDIO (Space Defense Initiative Organization), mission to the Moon and the asteroid Geographos. This mission is designed as a long term stressing test on sensors and space systems developed for SDIO. In the course of this test Clementine will obtain science data using a varied and powerful array of remote sensing instruments which were developed by or for Lawrence Livermore National Laboratory in Livermore, California. Clementine carries five cameras, one for navigation and four for science experiments. In addition, a laser ranger is included which will serve as a laser altimeter. The Clementine cameras cover a wider range of spatial resolutions and wavelength range than did Galileo and are almost ideally suited to mapping of mafic rock types as are present on the Moon and expected at Geographos. Calibration of the cameras will occur at the sensor calibration laboratory at LLNL. In flight calibrations, using standard stars and other standards should improve the stated accuracies. Signal-to-noise ratios (SNRs) include the following noise sources: shot noise, calibration error, digitization noise, readout noise, and frame transfer noise (where applicable). The achieved SNRs are a balance between detector saturation and acceptable image smear. The 'worst' case uses the longest possible integration times.

Lucey, Paul G.↗

DOE OSTI2025

Automating Anomaly Detection for Target systems at Spallation Neutron Source

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory, produces the world’s most intense pulse neutrons beams. An accelerated proton beam is directed into a mercury target to generate neutrons via spallation. The target system accounted for over 40% of the overall downtime of the facility in 2022. Thus, early detection in anomalies in the target systems can enable taking corrective actions to avoid failures and reduce downtime. Fault prognostics and anomaly detection in accelerators, both at SNS and outside, has largely focused on the beam side. This paper presents one the first studies exploring leveraging machine learning to automate the detection of anomalies in the target system. The target system consists of over 30 different interconnected subsystems, and the present work focuses on the mercury process system as a use case. Analyzing data from 28 process variables from 2022 and 2023, tree-based and reconstruction-based algorithms are employed to detect anomalies in archived data. The algorithms detected previously unreported anomalies, several of which were deemed alert worthy by human experts, particularly those found by reconstruction-based algorithms. Using data from each production run in the accelerator increased the generalizability of the models in time. Efforts are now underway to implement a workflow for incorporating human feedback to update the models and evaluating performance on unseen data. The models will eventually be integrated into the existing System Tracking and Reliability system with a web interface for automated anomaly detection and reporting along with a pathway for incorporating human feedback for model updates.

Raj, Anant [ORNL] (ORCID:0000000306711244)↗

NASA NTRS1981

Data use investigations for applications Explorer Mission A (Heat Capacity Mapping Mission): HCMM's role in studies of the urban heat island, Great Lakes thermal phenomena and radiometric calibration of satellite data

The utility of data from NASA'a heat capacity mapping mission satellite for studies of the urban heat island, thermal phenomena in large lakes and radiometric calibration of satellite sensors was assessed. The data were found to be of significant value in all cases. Using HCMM data, the existence and microstructure of the heat island can be observed and associated with land cover within the urban complex. The formation and development of the thermal bar in the Great Lakes can be observed and quantitatively mapped using HCMM data. In addition, the thermal patterns observed can be associated with water quality variations observed both from other remote sensing platforms and in situ. The imaging radiometer on-board the HCMM satellite is shown to be calibratible to within about 1.1 C of actual surface temperatures. These findings, as well as the analytical procedures used in studying the HCMM data, are included.

Schott, J. R.↗

NASA NTRS1990

Upwind control volumes - A new upwind approach

This paper presents a new algorithm for the solution of the steady Euler equations in two-dimensional flow. It uses an upwind control volume approach in which a standard flux residual on triangular cells is distributed with a downwind bias. The resulting scheme is second order accurate on unstructured triangular meshes and produces sharp shocks without the addition of any shock smoothing. Results demonstrate its performance on a standard AGARD test case using both smooth and irregular unstructured meshes.

Giles, Michael↗

NASA NTRS2020

LaRC SmartLab Apps For Instrument Control And Data Processing: Optical Micrometer Data Visualizer

The LaRC Smart Lab applications are a series of software tools to greatly enhance researcher efficiency by streamlining and automating workflows. Python scripts and applications are increasingly being used in scientific workflows, including for instrument control and data processing. Interactive Python scripting environments such as Jupyter Lab provide powerful tools for using Python. In some use cases, the development of standalone applications with dedicated graphical user interfaces (GUIs) can enhance the utility of the code and open it up to more users, including non-programmers. Here, we describe a GUI based optical micrometer data visualization application developed as part of the LaRC SmartLab project. We highlight its use in visualizing experimental data and briefly discuss its implementation to give pointers to programmers who wish develop work based on this application's or similar co de.

LaRC SmartLab↗

NASA NTRSDate not supplied

Improving Computational Efficiency of Prognostics Algorithms in Resource-Constrained Settings

The field of prognostics and health management provides quantitative methods for monitoring and predicting the health of physical systems. Prognostics algorithms are useful in that they can be employed to assess the current state of a system, propagate the system state throughout time, and predict potential anomalies or failures that may occur. However, effective prognosis can be challenging to achieve in resource-constrained settings due to computational limitations and high computational latency, leading to obsolete predictions. Thus, computationally efficient and accurate algorithms are necessary for some prognostics applications. In this work, we implement three new algorithmic approaches to prediction (sampling methods, variable prediction time step, variable prediction sample size) with the goal of improving computational efficiency while minimizing decrease in model accuracy. To quantitatively analyze our results, we examine a use-case of degradation of a Lithium-ion battery. Notably, through this work it was found that none of the sampling approaches had a significant impact on computational efficiency or model accuracy in predicting EOD of the battery. However, our results show that prediction accuracy is highly dependent on the time step used, and that an appropriate time step can optimize both model accuracy and simulation efficiency. Finally, implementing a variable sample size also affected prediction, and our results show that tuning both the magnitude and timing of the sample size adjustment in an application-specific manner may prove useful in some applications. Taken together, our findings highlight the challenge of performing prognostics in resource-constrained settings, and illustrate the potential of developing new prediction algorithms to improve computational efficiency of prognosis.

Prognostics↗

DOE OSTI2022

VOLTTRON Modular Framework: Enabling flexible and scalable deployment solutions

VOLTTRON ™ is an open-source platform for distributed sensing and control. The platform provides services for collecting and storing data from buildings and devices and provides an environment for developing applications which interact with that data. The platform allows developers to build out their use cases by utilizing these frameworks and integrating new capabilities. To simplify the deployment of systems built on VOLTTRON, a new way of organizing the codebase is being explored. This document details these efforts through a new code repository layout for the VOLTTRON platform and services, and how this new layout provides targeted deployments using standard python deployment packages (wheels). In addition, this paper will discuss the development of third-party agents and how they can be integrated within the VOLTTRON ecosystem. Finally, we will discuss core platform development and direction for the modularized version of VOLTTRON.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Defining Computational Emissivity Uncertainty Over Large Temperature Scales Due to Surface Evolution

There is a dearth in the literature on how to capture the uncertainty generated by material surface evolution in thermal modeling. This leads to inadequate or highly variable uncertainty representations for material properties, specifically emissivity when minimal information is available. Inaccurate understandings of prediction uncertainties may lead decision makers to incorrect conclusions, so best engineering practices should be developed for this domain. In order to mitigate the aforementioned issues, this study explores different strategies to better capture the thermal uncertainty response of engineered systems exposed to fire environments via defensible emissivity uncertainty characterizations that can be easily adapted to a variety of use cases. Here, two unique formulations (one physics-informed and one mathematically based) are presented. The formulations and methodologies presented herein are not exhaustive but more so are a starting point and give the reader a basis for how to customize their uncertainty definitions for differing fire scenarios and materials. Lastly, the impact of using this approach versus other commonly used strategies and the usefulness of adding rigor to material surface evolution uncertainty is demonstrated.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Packages of Distributed Energy Technologies Demonstrating Demand Flexibility at Community Scale

The combination of increased electric load growth across all sectors, deferred electrical infrastructure investment, and other factors resulting in variable electric power supply, has created technical challenges to maintaining a resilient and reliable grid. Many federal, regional, and local efforts are in play to modernize the electric grid, including advancing building technologies and distributed energy resources (DERs) that are utilizing smarter controls to become responsive to both occupant and grid needs. This report reviews ten pilot projects demonstrating how groups of buildings combined with behind-the-meter (BTM) DERs such as electric vehicle (EV) charging, battery storage, flexible HVAC and domestic hot water systems, and photovoltaic systems can reliably and cost effectively provide grid services. Each of the ten pilot projects aim to deliver both energy efficiency and demand flexibility (DF) while supporting load growth. The ten demonstration teams are piloting flexible DER packages across diverse communities of residential and commercial buildings to address a variety of regional grid needs. The outcomes of these pilot projects will be used to inform future scaling through utility program development. This paper characterizes the ten teams, showcasing the decision-making process used by each group to develop their packages (Section 2), the grid services they plan to deliver (Section 3), the types of DER packages selected for deployment within building sectors (Section 4) and trends between building sector, DER types, and grid services In order to achieve community scale benefits, the pilot projects must utilize aggregated control mechanisms for coordinating buildings and DERs together. Several types of coordinated control architectures have evolved amongst the teams, influenced by use type, existing market conditions, and integration type. Three coordinated controls architectures have been characterized, highlighting their use cases, benefits, challenges, and tradeoffs in their design. These insights can aid utilities, control vendors, and developers in scaling community-level energy systems (Paul, 2024). Ultimately, the technology packages selected by the ten teams will be coordinated to provide power system services, also known as grid services. Insights from these demonstrations will be useful for grid operators, regulators, aggregators and other stakeholders as they look to deploy demand flexible resources as grid services in the future. The grid services that each team is targeting for demonstration are described in Section 3 and Section 4. Methods for evaluating the grid services have been described in the paper Metrics for Evaluating Grid Service Provision from Communities of Grid-interactive and Efficient Buildings and other DER (MacDonald, 2023). To identify technology packages for demonstration, Section 2 shows that project teams used a range of analysis approaches, including building energy modeling, AMI data analysis, cost-benefit frameworks, and utility pilot data. Some teams emphasized technical modeling to quantify grid impacts and demand reduction potential, while others prioritized economic evaluations, stakeholder input, or exploratory pilots to inform deployment decisions. This diversity reflects the need to tailor selection methods to project goals, available data, and organizational context. Section 5 discusses trends between the DER technologies deployed and the grid service provisions from each team. Residential buildings (multifamily and single family) lean towards technologies that enhance energy efficiency (e.g. weatherization upgrades, smart thermostats) and onsite power generation integration (e.g. solar PV). Commercial building demonstrations prioritize technologies that ensure operational reliability (e.g. battery storage) and centralized energy management systems and optimization solutions. Teams that are deploying controllable storage-based technologies are more likely to provide grid services that require a near real-time response. Teams incorporating load shifting technologies like smart thermostats with HEMs are likely to include energy markets participation and customer bill management offerings. Campus demonstrations are adopting diverse sets of DERs to emphasize renewable generation, paired with centralized control. This section also describes technologies that were considered during project planning but ultimately excluded from final deployment. These demonstrations reveal that effective DER package design should be tailored to building type, customer segment, and construction vintage. Multifamily buildings benefit from centralized HVAC upgrades and supervisory controls, while single-family homes are well-suited for individualized technologies like solar, storage, and smart home energy monitors. Commercial and campus settings prioritize EMIS integration and load optimization. New construction enables cost-effective integration of DER-ready infrastructure, whereas retrofits require deployments aligned with owner and tenant value streams. For utility program planners, early coordination with developers and building owners, paired with segmented and modular program offerings, can improve adoption, scalability, and grid impact.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2024

Securing Small Modular Reactors in Urban Environments

Current small modular reactor (SMR) deployment use cases consider both rural and urban deployments, depending on the operational in-country needs for clean and reliable sources of energy. Many studies have been conducted analyzing security in rural and remote deployment locations, but this study looks at the physical security implications of an SMR placed in an urban environment and its uses for electricity production, district heating, and process heating. SMRs used for electricity production, district heating, and process heating may be key sources of both energy infrastructure and commercial infrastructure within a city and a State. As a result, long-term shutdowns could have a serious impact on a State’s overall energy or commercial production. Therefore, operators may consider further security applications to protect an SMR plant from physical attacks against both radiological sabotage and sabotage acts that could result in the SMR facility being offline for a significant amount of time. In this study, the team designed and analyzed a physical protection system (PPS) for securing an urban SMR facility against acts of radiological sabotage and sabotage acts that could disrupt the facility’s long-term operation. Additionally, this work analyzed the nuanced security issues related to siting an SMR near an urban environment (versus in a rural environment). The result of these analyses includes recommendations for PPSs for urban SMR facilities used for energy production, district heating, and process heating.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗