Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “turning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Interfacial wave theory of dendrite growth - Global mode solution and quantum condition

The signal feedback process at the edge of the dendrite tip is investigated, and the global instability mechanism of the system is derived. A mechanism is developed to describe a discrete set of unstable global modes for the system. Called WEASR, the method considers the wave emission at the turning point and signal reflections between the turning point and the front edge of the tip. It is shown that the method can obtain the asymptotic solutions for the unstable global modes and the quantum condition for the corresponding eigenvalues. A turning point called the pattern formation condition is shown to be crucial in the formation of dendritic structure and the choice of the final tip velocity. The wave emission process is outlined, and the importance of a signal feedback process at the edge of the dendrite tip is demonstrated. Parameters such as stability and surface tension can be analyzed in terms of their effects on WEASR modes.

Xu, Jian-Jun↗

Examination of time-variable input effects in a nonlinear analogue magnetosphere model

The plasma physical analog model (an extension of the damped, harmonic-oscillator dripping faucet model) is employed to consider explicitly the effect of time-varying the inputs. This work is equivalent to considering the effects of northward and southward turnings of the interplanetary magnetic field for various periods of time. It is found that relatively extended episodes (not less than 2 hours) of turned-on input with shorter (about 1 hour) periods of turned-off input lead to model behavior much like the continuously driven case. Going to short input intervals with longer periods of zero input leads to highly irregular and dramatically fluctuating episodes of magnetotail unloading. These results give an insight into the diversity of apparent magnetospheric responses during relatively isolated substorm conditions. This work shows the absolutely critical interdependence (in a nonlinear dynamical system) of input phasing and internal magnetospheric response cycles.

Baker, D. N.↗

The gamma ray continuum spectrum from the galactic center disk and point sources

A light curve of gamma-ray continuum emission from point sources in the galactic center region is generated from balloon and satellite observations made over the past 25 years. The emphasis is on the wide field-of-view instruments which measure the combined flux from all sources within approximately 20 degrees of the center. These data have not been previously used for point-source analyses because of the unknown contribution from diffuse disk emission. In this study, the galactic disk component is estimated from observations made by the Gamma Ray Imaging Spectrometer (GRIS) instrument in Oct. 1988. Surprisingly, there are several times during the past 25 years when all gamma-ray sources (at 100 keV) within about 20 degrees of the galactic center are turned off or are in low emission states. This implies that the sources are all variable and few in number. The continuum gamma-ray emission below approximately 150 keV from the black hole candidate 1E1740.7-2942 is seen to turn off in May 1989 on a time scale of less than two weeks, significantly shorter than ever seen before. With the continuum below 150 keV turned off, the spectral shape derived from the HEXAGONE observation on 22 May 1989 is very peculiar with a peak near 200 keV. This source was probably in its normal state for more than half of all observations since the mid-1960's. There are only two observations (in 1977 and 1979) for which the sum flux from the point sources in the region significantly exceeds that from 1E1740.7-2942 in its normal state.

Gehrels, Neil↗

Inertial oscillation of a vertical rotating draft with application to a supercell storm

An analytic model (vertical rotating draft) which includes the gross features of a supercell storm on an f-plane, undergoes an inertial oscillation that appears to have been overlooked in previous analytic and numerical models. The oscillation is nonlinear and consists of a long quiescent phase and a short intense phase. During the intense phase, the rotating draft has the following features of a supercell: the diameter of the core contracts as it spins up and expands as it spins down; if vertical wind shear is included, the track of the rotating draft turns to the right (an anticyclonic rotating draft turns to the left); this turning point is followed by a predominantly upward flow; and the horizontal pressure gradient is very small (a property of most tornadoless supercells). The rapid spin-up during the intense phase and the high Rossby numbers obtainable establish the ability of the Coriolis force to spin up single cyclonic or anticyclonic supercells by means of this inertial oscillation. This surprising result has implications for numerical supercell simulations, which generally do not rely on the Coriolis force as a source of rotation. The physics and mathematics of the inertial oscillation are given, and the solution is applied to a documented supercell.

Supercell thunderstorm↗

Estimating Wear Of Installed Ball Bearings

Simple inspection and measurement technique makes possible to estimate wear of balls in ball bearing, without removing bearing from shaft on which installed. To perform measurement, one observes bearing cage while turning shaft by hand to obtain integral number of cage rotations and to measure, to nearest 2 degrees, number of shaft rotations producing cage rotations. Ratio between numbers of cages and shaft rotations depends only on internal geometry of bearing and applied load. Changes in turns ratio reflect changes in internal geometry of bearing provided measurements made with similar bearing loads. By assuming all wear occurs on balls, one computes effective value for this wear from change in turns ratio.

Keba, John E.↗

Investigation of a Full-scale, Cascade-type Thrust Reverser

A double set of turning vanes was carried inside the jet tailpipe. To produce reverse thrust, the tailpipe opens into two side sections and the turning vanes move outward to form a V-shaped cascade, which deflects the exhaust-gas flow. Forward and reverse net thrust were measured over a range of engine speeds with the airplane stationary. Taxi tests were made to determine the comparative stopping distances using wheel braking and reverse thrust separately, and a combination of both. The effect of turning-vane spacing on thrust-reverser performance was determined by scale-model tests using unheated air.

ENGINES, TURBOJET↗

Flight Tests on U.S.S. Los Angeles. Part I : Full Scale Pressure Distribution Investigation

The primary purpose of this investigation was to obtain simultaneous data on the loads and stress experience in flight by the U. S. S. Los Angeles which could be used in rigid airship structure design. A secondary object of the investigation was to determine the turning and drag characteristics of the airship. The aerodynamic loading was obtained by measuring the pressure at 95 locations on the tail surfaces, 54 on the hull, and 5 on the passenger car. These measurements were made during a series of maneuvers consisting of turns and reversals in smooth air and during a cruise in rough air which was just short of squall proportions. The results of the pressure measurements on the hull indicate that the forces on the forebody of an airship are relatively small. The tail surface measurements show conclusively that the forces caused by gusts are much greater than those caused by horizontal maneuvers. In this investigation the tail surface loadings caused by gusts closely approached the designed loads of the tail structure. The turning and drag characteristics will be reported in separate reports.

De France, S J↗

Maneuverability Investigation of an O3U-1 Observation Airplane

This report presents the results of maneuverability tests of an O3U-1 observation airplane. This investigation is the third in a series of similar investigations requested by the Bureau of Aeronautics (Navy) for the purpose of comparing the maneuverability of different airplane types and to provide quantitative data for use in establishing a criterion or method for rating the maneuverability of an airplane. The two former investigations were conducted with the fighter types designated F6C-3 and F6C-4 and have been reported previously. Measurement of the air speed, the angular velocity, the linear acceleration, and positions of the controls were made during abrupt single-control maneuvers with three stop positions for each control, during steady horizontal turns for the determination of minimum radius, and during 180 degree turns by various methods. Flight-path coordinates in two dimensions were determined for the 180 degree turns by means of a special camera obscura designed for the previous investigation of the F6C-4 airplane. All maneuvers were performed at an altitude of approximately 3,000 feet.

Thompson, F L↗

Data for Design of Entrance Vanes from Two-Dimensional Tests of Airfoils in Cascade

As a part of a program of the NACA directed toward increasing the efficiency of compressors and turbines, data were obtained for application to the design of entrance vanes for axfax-flow compressors or turbines. A series of blower-blade sections with relatively high critical speeds have been developed for turning air efficiently from 0 deg to 80 deg starting with an axial direction. Tests were made of five NACA 65-series blower blades (modified NACA 65(216)-010 airfoils) and of four experimentally designed blower blades in a stationary cascade at low Mach numbers. The turning effectiveness and the pressure distributions of these blade sections at various angles of attack were evaluated over a range of solidities near 1. Entrance-vane design charts are presented that give a blade section and angle of attack for any desired turning angle. The blades thus obtained operate with peak-free pressure distributions. Approximate critical Mach numbers were calculated from the pressure distributions.

FLOW-VANES, GUIDE↗

A study of curvilinear flight

When an airplane describes a curve it takes a certain time for it to turn from level to inclined position and then back to level again. In the following, we express the motion about the horizontal axis as "roll" or "bank" and the motion perpendicular to the vertical axis, i.e., the actual curve, as "turn." Equations and tables provide results on various aspects of turns, control settings, acceleration, inertia moments, and angular velocity.

Kruse, Helmuth↗

Turbine-Driven Pipe-Cleaning Brush

Simple pipe-cleaning device includes small turbine wheel axially connected, by standoff, to circular brush. Turbine wheel turns on hub bearing attached to end of upstream cable. Turbine-and-brush assembly inserted in pipe with cable trailing upstream and brush facing downstream. Water or cleaning solution pumped through pipe. Cable held at upstream end, so it holds turbine and brush in pipe at location to be cleaned. Flow in pipe turns turbine, which turns wheel, producing desired cleaning action. In addition to brushing action, device provides even mixing of cleaning solution in pipe.

Werlink, Rudy J.↗

Performances of a date dissemination code on telephone lines using commercial modems

A coded time/date information dissemination system (CTD), based on telephone lines and commercial modems, is now in its experimental phase in Italy at IEN. This service, born from a cooperation with other metrological laboratories (TUG, Austria, SNT, Sweden, VSL, The Netherlands), represents an attempt towards an European standardization. Some results of an experimental analysis in which a few modems were tested, both in laboratory conditions and connected to the telephone network, in order to evaluate the timing capability of the system are given. When the system is used in a one-way mode, in many practical cases the modems delay turns out to be the main factor which limits the accuracy, even more than the telephone line delays. If the two-way mode is used, the modems asymmetry, i.e., the delay difference between transmission and reception, is almost always the most important source of uncertainty, provided the link is not including a space segment. Comparing the widely used V.22 modems to the old V.21 ones, the latters turn out to be better both in delay time (30-100 ms V.22, and 7-15 ms V.21) and asymmetry (10-50 micro-s V.22, and 10 ms V.22). Time transfer accuracies of 10 micron-s (same turn) to 100 micro-s (long distance calls) were obtained in two-way mode with commercial V.21 modems.

Cordara, F.↗

AXAF SIM focus mechanism study

The design requirements and initial design concept for the AXAF-I Science Instrument Module (SIM) were reviewed at Ball on September 29, 1993. The concept design SIM focus mechanism utilizes a planetary gearset, with redundant motors, to drive a large ring (called 'main housing bearing') via a spur gearset. This large drive ring actuates three tangent bar links (called 'push rods'), which in turn actuate three levers (called 'pin levers'). Each of the three pin levers rotates an 'eccentric pin,' which in turn moves the base of a bipod flexure in both the radial (normal to optical axis) and axial (focus along optical axis) directions. Three bipod flexures are employed, equally spaced at 120 degrees apart, the base of each being translated in the two directions as described above. A focus adjustment is made by rotating the drive ring, which drives the push rods and therefore the pin levers, which in turn rotate the eccentric pins, finally imparting the two motions to the base of each of the bipod flexures. The axial translation (focus adjustment) of the focused structure is the sum of the direct axial motion plus axial motion which comes from uniformly squeezing the three bipod bases radially inward. SAO documented the following concerns regarding the focus mechanism in memo WAP-FY94-001, dated October 7, 1993: (1) The focus adjustment depends, in large part, on the structural properties (stiffnesses and end fixities) of the bipod flexures, push rods, pin levers and eccentric pins. If these properties are not matched very well, then lateral translations as well as unwanted rotations of the focussed structure will accompany focus motion. In addition, the stackup of linkage tolerances and any nonuniform wear in the linkages will result in the same unwanted motions. Thermal gradients will also affect these motions. At the review Ball did not present supporting analyses to support their choice of this design concept. (2) The proposed 'primary' method of measuring focus is by counting motor steps. The 'backup' method is by a pot mounted on the drive ring. Neither method provides for a direct measurement of the quantity desired (focus position). This is of concern because of the long and indirect relationship between focus and the sensed quantity (drive ring rotation). There are three sinusoidal relationships and structural stiffness in the path, and the resulting calibration is likely to be highly nonlinear. These methods would require an accurate ground calibration. (3) Ground calibration (and verification) of focus vs. drive position must be done in 1-g on the ground. This calibration will be complicated by both the structural characteristics of the bipods and the fact that the CG of the translating portion of the SIM is not on the optical axis (thereby causing unwated rotations and changing the focus position vs. motor step and pot readout relationships). The SIM translating weight could be offloaded, but the calibration then becomes sensitive to any errors in offloading (both magnitude and direction). There are concerns as to whether a calibration to the required accuracy can be accomplished on the ground. (4) The choice of a potentiometer as the focus position sensor is questionable in terms of reliability for a five year mission. The results of SAO's study of items 1, 2 and 3 described above are presented in this report.

Tananbaum, H. D.↗

A Flexible Alignment Fixture for the Fabrication of Replication Mandrels

NASA uses precision diamond turning technology to fabricate replication mandrels for its X-ray Calibration Facility (XRCF) optics. The XRCF optics are tubular, and the internal surface contains a parabolic profile over the first section and a hyperbolic profile over the last. The optic is fabricated by depositing layers of gold and nickel on to the replication mandrel and then separating it from the mandrel. Since the mandrel serves as a replication form, it must contain the inverse image of the surface. The difficulty in aligning the mandrel comes from the fabrication steps which it undergoes. The mandrel is rough machined and heat treated prior to diamond turning. After diamond turning, silicon rubber separators which are undercut in radius by 3 mm (0.12 in.) are inserted between the two end caps of the mandrel to allow the plating to wrap around the ends (to prevent flaking). The mandrel is then plated with a nickel-phosphor alloy using an electroless nickel process. At this point, the separators are removed and the mandrel is reassembled for the final cut on the DTM. The mandrel is measured for profile and finish, and polished to achieve an acceptable surface finish. Wrapping the plating around the edges helps to prevent flaking, but it also destroys the alignment surfaces between the parts of the mandrel that insure that the axes of the parts are coincident. Several mandrels have been realigned by trial-and-error methods, consuming significant amounts of setup time. When the mandrel studied in this paper was reassembled, multiple efforts resulted in a minimum radial error motion of 100 microns. Since 50 microns of nickel plating was to be removed, and a minimum plating thickness of 25 microns was to remain on the part, the radial error motion had to be reduced to less than 25 microns. The mandrel was therefore not usable in its current state.

Cuttino, James F.↗

Preliminary Measurements of the Noise Characteristics of Some Jet-Augmented-Flap Configurations

Experimental noise studies were conducted on model configurations of some proposed jet-augmented flaps to determine their far-field noise characteristics. The tests were conducted using cold-air jets of circular and rectangular exits having equal areas, at pressure ratios corresponding to exit velocities slightly below choking. Results indicated that the addition of a flap to a nozzle may change both its noise radiation pattern and frequency spectrum. Large reductions in the noise radiated in the downward direction are realized when the flow from a long narrow rectangular nozzle as permitted to attach to and flow along a large flap surface. Deflecting or turning the jet flow by means of impingement on the under surfaces increases the noise radiated in all directions and especially in the downward direction for the jet-flap configurations tested. Turning of the flow from nozzles by means of a flap turns the noise pattern approximately an equal amount. The principle of using a jet-flap shield with flow attachment may have some application as a noise suppressor.

Maglieri, Domenic J.↗

A Limited Study of a Hypothetical Winged Anti-ICBM Point-Defense Missile

A preliminary investigation was conducted to determine whether a warhead stage of an antimissile missile could be placed within an arbitrary 2-nautical-mile-radius maneuver cylinder around an intercontinental-ballistic-missile (ICBM) flight path above an altitude of 140,000 feet, a horizontal range of 40 nautical miles, at a flight-path angle of approximately 20 deg, and within 50 seconds after take-off using only aerodynamic forces to turn the antimissile missile. The preliminary investigation indicated that an antimissile missile using aerodynamic forces for turning was capable of intercepting the ICBM for the stated conditions of this study although the turning must be completed below an altitude of approximately 70,000 feet to insure that the antimissile missile will be at the desired flight-path angle. Trim lift coefficients on the order of 2 to 3 and a maximum normal-acceleration force of from 25g to 35g were necessary to place the warhead stage in intercept position. The preliminary investigation indicated that for the two boosters investigated the booster having a burning time of 10 seconds gave greater range up the ICBM flight path than did the booster having a burning time of 15 seconds for the same trim lift coefficient and required the least trim lift coefficient for the same range.

Brown, Clarence A., Jr.↗

UVI Auroral Observations During the January 10, 1997 Magnetic Cloud Event

Solar wind IMF and plasma conditions surrounding the January 10-11 magnetic cloud event provided very interesting observations relating to magnetospheric and ionospheric processes. Prior to the arrival of the magnetic cloud a shock front followed by abrupt swings in the IMF orientation were observed by the Wind spacecraft at about 100 Re upstream. The Polar Ultraviolet Imager (UVI) near apogee over the northern hemisphere recorded the encounter of the shock with the magnetosphere. Enhancement of dayside precipitation around noon MLT and progression of the enhancement along dawn and dusk flanks of the oval culminating in a very localized pseudo onset near midnight MLT were observed. During the following mainly northward IMF the polar cap region was the site of multiple sunward aligned arcs and curled arc structures that persisted until the IMF turned rapidly southward. While the IMF remained southward the polar cap cleared of arc structures and expanded, and the auroral oval became very thin. No substorms were observed for at least 25 minutes after the following northward turning contrary to what might be expected on the basis of recent reports of substorm initiation by northward turning of the IMF. These observations and others during the magnetic cloud event provide a clear case study of the effect of the solar wind on dayside precipitation, thickness of the boundary layer, magnetosphere-polar cap magnetic topology and sources of the polar cap precipitation, and triggering of substorms. These issues will be discussed along with the presentation of the UVI auroral observations and solar wind measurements.

Brittnacher, M. J.↗

Observations of Sea Surface Mean Square Slope During the Southern Ocean Waves Experiment

For the Southern Ocean Waves Experiment (SOWEX), conducted in June 1992 out of Hobart, Tasmania, the 36 GHz (8.3 mm) NASA Scanning Radar Altimeter (SRA) was shipped to Australia and installed on a CSIRO Fokker F-27 research aircraft instrumented to make comprehensive surface layer measurements of air-sea interaction fluxes. The sea surface mean square slope (mss), which is predominantly caused by the short waves, was determined from the backscattered power falloff with incidence angle measured by the SRA in the plane normal to the aircraft heading. On each flight, data were acquired at 240 m altitude while the aircraft was in a 7 deg roll attitude, interrogating off-nadir incidence angles from -15 deg through nadir to +29 deg. The aircraft turned azimuthally through 810 deg in this attitude, mapping the azimuthal dependence of the backscattered power falloff with incidence angle. Two sets of turning data were acquired on each day, before and after the aircraft measured wind stress at low altitude (12 m to 65 m). Wave topography and backscattered power for mss were also acquired during those level flight segments whenever the aircraft altitude was above the SRA minimum range of 35 m. A unique feature of this experiment was the use of a nadir-directed low-gain horn antenna (35 deg beamwidth) to acquire azimuthally integrated backscattered power data versus incidence angle before and after the turn data.

Walsh, E. J.↗