Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal system modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Modeling of thermal and kinetic processes in non-equilibrium plasma ignition applied to a lean combustion engine

In recent years novel ignition systems have been developed to enable stable and efficient engine operations with lean mixtures. Among them, radio-frequency corona ignition systems create discharges that involve a much wider region compared to traditional spark, and produce non equilibrium plasma with high levels of active radicals and excited species. These devices considerably increase the early flame growth speed and extend stable operating limits. With the aim of expanding the knowledge on high efficiency lean-burn SI engines, this paper investigates and compares the combustion development generated by spark and corona ignitions through computational fluid dynamics, within the Reynolds-Averaged Navier-Stokes framework for turbulence modeling. In order to simultaneously take thermal and chemical effects into account, the Perfectly Stirred Reactor combustion model is used. Experimental data are also collected for validation in an optical access engine, for different mixture levels, from stoichiometric to very lean. Furthermore, the faster burn rate generated by the corona system in the initial stage of the combustion is well predicted by the simulations, in all the relative air-fuel ratio conditions. Remarkably, as the mixture becomes lean, simulations are able to capture the non-linear transition from fast to slow kernel growth, before a self-sustainable flame propagation is established. This correlates very well with the measured engine cyclic variability and the corresponding steep change in the duration of the flame kernel formation. Ultimately, this study highlights the important role of the atomic oxygen, as active radical, in promoting and enhancing the combustion initiated by a corona discharge, in addition to the volumetric ignition effect. By contrast, the validated simulations allow to explain that the high-temperature thermal plasma generated in a traditional spark discharge is insensitive to kinetic aspects.

42 ENGINEERING↗
DOE OSTI2022

Transformer Health Monitoring Using Dissolved Gas Analysis

As integral components of any power plant, transformers supply the generated electricity to the grid. However, a transformer’s cellulose-based paper insulation and the mineral oil in which it is immersed break down over time under standard operating conditions—or more rapidly due to potential faults within the system. As the transformer’s mineral oil breaks down, gases are released that can be measured and monitored. This technical brief exhibits a collection of diagnostic and prognostic techniques that utilities can adopt in lieu of labor-intensive periodic preventive maintenance routines. Furthermore, prognostic models have been incorporated using the latest version of the Institute of Electrical and Electronics Engineers (IEEE) standard (IEEE, 2019) for dissolved gas analysis (DGA), thus expanding it to include estimation of the time to maintenance. Overall, four different methodologies are explained, each of which aids in determining a transformer’s state of health. These methodologies include the Chendong model, the IEEE thermal life consumption model (IEEE, 2012), a diagnostic model for DGA, and a prognostic model for DGA that uses an autoregressive integrated moving average (ARIMA) model. An additional improvement for estimating missing system parameters by using monitoring data (i.e., a tool for parameter estimation utilizing Powell’s method) is presented, enabling the IEEE thermal life consumption model to benefit not only the collaborating power plant, but also the power industry at large.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRSDate not supplied

Mechanical Erosion Modeling of TPS Materials

This work describes the development of a model that accounts for the additional total surface recession in Thermal Protection Systems materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics capability module was integrated within the Porous material Analysis Toolbox based on OpenFOAM, PATO. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver module computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model of the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.

Stress Analysis↗
DOE OSTI2021

Investigation of GaAs surface treatments for ZnSe growth by molecular beam epitaxy without a buffer layer

Atomically clean and smooth surfaces are critical prerequisite for the epitaxial regrowth of dissimilar semiconductors. Using ZnSe/GaAs as a model system, epitaxial regrowth without a buffer layer after thermal cleaning with various As-fluxes, atomic Ga flux, and atomic hydrogen treatments to the GaAs substrates and the surfaces were investigated in this work via in-situ Auger electron spectroscopy (AES). The ZnSe epilayers grown on the pre-treated GaAs surfaces without a buffer layer were characterized by X-ray diffraction (XRD), photoluminescence (PL) and atomic force microscopy (AFM) to evaluate the effectiveness of the surface treatment methods. It was found that a high quality ZnSe layer can be achieved by atomic hydrogen surface treatment at 300°C without requiring GaAs buffer layer growth, which reveals a path for epitaxy growth avoiding high temperature treatments.

42 ENGINEERING↗
DOE OSTI2022

Arctic Ocean annual high in ${{\boldsymbol{p}}}_{{{\bf{CO}}}_{{\bf{2}}}}$ could shift from winter to summer

Long-term stress on marine organisms from ocean acidification will differ between seasons. As atmospheric carbon dioxide (CO 2 ) increases, so do seasonal variations of ocean CO 2 partial pressure (p co 2 ), causing summer and winter long-term trends to diverge. Trends may be further influenced by an unexplored factor—changes in the seasonal timing of p co 2 . In Arctic Ocean surface waters, the observed timing is typified by a winter high and summer low because biological effects dominate thermal effects. Here we show that 27 Earth system models simulate similar timing under historical forcing but generally project that the summer low, relative to the annual mean, eventually becomes a high across much of the Arctic Ocean under mid-to-high-level CO 2 emissions scenarios. Often the greater increase in summer p co 2 , although gradual, abruptly inverses the chronological order of the annual high and low, a phenomenon not previously seen in climate-related variables. The main cause is the large summer sea surface warming from earlier retreat of seasonal sea ice. Warming and changes in other drivers enhance this century’s increase in extreme summer p co 2 by 29 ± 9 per cent compared with no change in driver seasonalities. Thus the timing change worsens summer ocean acidification, which in turn may lower the tolerance of endemic marine organisms to increasing summer temperatures.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Floquet operator dynamics and orthogonal polynomials on the unit circle

Operator spreading under stroboscopic time evolution under a unitary is studied. An operator Krylov space is constructed and mapped to orthogonal polynomials on a unit circle (OPUC), as well as to the Krylov space of the edge operator of the Floquet transverse field Ising model with inhomogeneous couplings (ITFIM). The Verblunsky coefficients in the OPUC representation are related to the Krylov angles parametrizing the ITFIM. The relations between the OPUC and spectral functions are summarized and several applications are presented. These include derivation of analytic expressions for the OPUC under persistent m-periodic dynamics, and the numerical construction of the OPUC for autocorrelations of the homogeneous Floquet-Ising model as well as the Z 3 clock model. The numerically obtained Krylov angles of the Z 3 clock model with long-lived period tripled autocorrelations show a spatial periodicity of six, and this observation is used to develop an analytically solvable model for the ITFIM that mimics this behavior.

Floquet systems↗
DOE OSTI2021

Direct Subsurface Measurements through Precise Micro Drilling

Wellbore integrity is a significant problem in the U.S. and worldwide, which has serious adverse environmental and energy security consequences. Wells are constructed with a cement barrier designed to last about 50 years. Indirect measurements and models are commonly used to identify wellbore damage and leakage, often producing subjective and even erroneous results. The research presented herein focuses on new technologies to improve monitoring and detection of wellbore failures (leaks) by developing a multi-step machine learning approach to localize two types of thermal defects within a wellbore model, a prototype mechatronic system for automatically drilling small diameter holes of arbitrary depth to monitor the integrity of oil and gas wells in situ, and benchtop testing and analyses to support the development of an autonomous real-time diagnostic tool to enable sensor emplacement for monitoring wellbore integrity. Each technology was supported by experimental results. This research has provided tools to aid in the detection of wellbore leaks and significantly enhanced our understanding of the interaction between small-hole drilling and wellbore materials.

42 ENGINEERING↗
NASA NTRS1975

The peculiar object HD 44179 /'The red rectangle'/

A strong infrared source detected in the AFCRL sky survey is confirmed, and is identified with the binary star HD 44179, embedded in a peculiar nebula. UBVRI and broad-band photometry between 2.2 and 27 microns are combined with blue, red, and near-infrared spectra, polarimetry and spectrophotometry of the star, and a range of direct and image-tube photographs of the nebula, to suggest a composite model of the system. In this model, the infrared radiation derives from thermal emission by dust grains contained in a disklike geometry about the central object, which appears to be of spectral type B9-A0 III and which may be in pre-main-sequence evolution. Two infrared emission features are found, peaking at 8.7 and 11.3 microns, the latter corresponding to the feature seen in the spectrum of the planetary nebula NGC 7027. The complex nebular structure is discussed on the basis of photographs through narrow-band continuum and emission-line filters. The polarization data support the suggestion of a disk containing some large particles. No radio continuum emission is detected.

Cohen, M.↗
NASA NTRS1977

Static aerodynamic characteristics of a single-stage-to-orbit vehicle with low planform loading at Mach numbers from 0.3 to 4.63

Transonic pressure and wind tunnel studies were performed to determine the longitudinal and lateral aerodynamic characteristics of a single-stage-to-orbit vehicle which utilizes an all metallic, hot structure, thermal protection system resulting in low planform loading. The model was tested over a Mach number range from 0.3 to 4.63 for angles of attack from -4 deg to 32 deg at both 0 deg and 5 deg sideslip.

Freeman, D. C., Jr.↗
NASA NTRS1979

Solar array technology for solar electric propulsion missions

Development of 66 W/kg and 200 W/kg solar arrays for solar electric propulsion is discussed along with two basic concentrator solar array design concepts. Considerable testing was performed to demonstrate the availability and capability of the technology used for these arrays. To provide complete demonstration of 66 W/kg technology, a full-scale wing was built and tested and NASA decided to fly it as an experiment on one of the early Shuttle flights. Performance of the concentrator array system was demonstrated by model testing in a thermal-vacuum chamber.

Young, L. E.↗
NASA NTRS1984

IDEAS: A multidisciplinary computer-aided conceptual design system for spacecraft

During the conceptual development of advanced aerospace vehicles, many compromises must be considered to balance economy and performance of the total system. Subsystem tradeoffs may need to be made in order to satisfy system-sensitive attributes. Due to the increasingly complex nature of aerospace systems, these trade studies have become more difficult and time-consuming to complete and involve interactions of ever-larger numbers of subsystems, components, and performance parameters. The current advances of computer-aided synthesis, modeling and analysis techniques have greatly helped in the evaluation of competing design concepts. Langley Research Center's Space Systems Division is currently engaged in trade studies for a variety of systems which include advanced ground-launched space transportation systems, space-based orbital transfer vehicles, large space antenna concepts and space stations. The need for engineering analysis tools to aid in the rapid synthesis and evaluation of spacecraft has led to the development of the Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) computer-aided design system. The ADEAS system has been used to perform trade studies of competing technologies and requirements in order to pinpoint possible beneficial areas for research and development. IDEAS is presented as a multidisciplinary tool for the analysis of advanced space systems. Capabilities range from model generation and structural and thermal analysis to subsystem synthesis and performance analysis.

Ferebee, M. J., Jr.↗
NASA NTRS1987

Space Station flight telerobotic servicer functional requirements development

The Space Station flight telerobotic servicer (FTS), a flight robotic system for use on the first Space Station launch, is described. The objectives of the FTS program include: (1) the provision of an alternative crew EVA by supporting the crew in assembly, maintenance, and servicing activities, and (2) the improvement of crew safety by performing hazardous tasks such as spacecraft refueling or thermal and power system maintenance. The NASA/NBS Standard Reference Model provides the generic, hierarchical, structured functional control definition for the system. It is capable of accommodating additional degrees of machine intelligence in the future.

Oberright, John↗
NASA NTRS1990

Space Station solar water heater

The feasibility of directly converting solar energy for crew water heating on the Space Station Freedom (SSF) and other human-tended missions such as a geosynchronous space station, lunar base, or Mars spacecraft was investigated. Computer codes were developed to model the systems, and a proof-of-concept thermal vacuum test was conducted to evaluate system performance in an environment simulating the SSF. The results indicate that a solar water heater is feasible. It could provide up to 100 percent of the design heating load without a significant configuration change to the SSF or other missions. The solar heater system requires only 15 percent of the electricity that an all-electric system on the SSF would require. This allows a reduction in the solar array or a surplus of electricity for onboard experiments.

Horan, D. C.↗
NASA NTRS1989

Thermal conductivity of metal-metal microlaminate composites

Microlaminate composites consisting of alternate layers of metal-metal, metal-ceramic and ceramic-ceramic exhibit anisotropy in thermal conductivity. Thermal conductivity in the direction perpendicular to the laminate plane is significantly lower than in the plane of the laminate. Results of the study on thermal conductivity of Ni-NiCoCrAlY and Ti-CoCrAlY microlaminate composites are presented. A semi-quantitative model explaining the thermal conductivity variation in the above systems as a function of number of layers is discussed. An expression correlating the experimental data with the calculated data for the above system is presented.

Radhakrishna, M. C.↗
NASA NTRS1991

Impact of diet on the design of waste processors in CELSS

The preliminary results of a design analysis for a waste processor which employs existing technologies and takes into account the constraints of human diet are presented. The impact of diet is determined by using a model and an algorithm developed for the control and management of diet in a Controlled Ecological Life Support System (CELSS). A material and energy balance model for thermal oxidation of waste is developed which is consistent with both physical/chemical methods of incineration and supercritical water oxidation. The two models yield quantitative analysis of the diet and waste streams and the specific design parameters for waste processors, respectively. The results demonstrate that existing technologies can meet the demands of waste processing, but the choice and design of the processors or processing methods will be sensitive to the constraints of diet. The numerical examples are chosen to display the nature and extent of the gap in the available experiment information about CELSS requirements.

Waleh, Ahmad↗
NASA NTRS1993

Nuclear Engine System Simulation (NESS). Version 2.0: Program user's guide

This Program User's Guide discusses the Nuclear Thermal Propulsion (NTP) engine system design features and capabilities modeled in the Nuclear Engine System Simulation (NESS): Version 2.0 program (referred to as NESS throughout the remainder of this document), as well as its operation. NESS was upgraded to include many new modeling capabilities not available in the original version delivered to NASA LeRC in Dec. 1991, NESS's new features include the following: (1) an improved input format; (2) an advanced solid-core NERVA-type reactor system model (ENABLER 2); (3) a bleed-cycle engine system option; (4) an axial-turbopump design option; (5) an automated pump-out turbopump assembly sizing option; (6) an off-design gas generator engine cycle design option; (7) updated hydrogen properties; (8) an improved output format; and (9) personal computer operation capability. Sample design cases are presented in the user's guide that demonstrate many of the new features associated with this upgraded version of NESS, as well as design modeling features associated with the original version of NESS.

Pelaccio, Dennis G.↗
NASA NTRS2009

System Modeling of Metabolic Heat Regenerated Temperature Swing Adsorption (MTSA) Subassembly for Prototype Design

This paper describes modeling methods for the three core components of a Metabolic heat regenerated Temperature Swing Adsorption (MTSA) subassembly: the sorbent bed, a sublimation (cooling) heat exchanger (SHX), and a condensing icing (warming) heat exchanger (CIHX). The primary function of the MTSA, removing carbon dioxide from a ventilation loop, is performed via the sorbent bed. The CIHX is used to heat the sorbent bed for desorption and to remove moisture from the ventilation loop while the SHX is alternately employed to cool the sorbent bed via sublimation of a spray of water at low pressure to prepare the reconditioned bed for the next cycle. This paper describes a system level model of the MTSA as developed in Thermal Desktop and SINDA/FLUINT including assumptions on geometry and physical phenomena, modeling methodology and relevant pa ra mete rizatio ns. Several areas of particular modeling interest are discussed. In the sorbent bed, capture of the translating CO2 saturation front and associated local energy and mass balance in both adsorbing and desorbing modes is covered. The CIHX poses particular challenges for modeling in SINDA/FLUINT as accounting for solids states in fluid submodels are not a native capability. Methods for capturing phase change and latent heat of ice as well as the transport properties across a layer of low density accreted frost are developed. This extended modeling capacity is applicable to temperatures greater than 258 K. To extend applicability to the minimum device temperature of 235 K, a method for a mapped transformation of temperatures from below the limit temperatures to some value above is given along with descriptions for associated material property transformations and the resulting impacts to total heat and mass transfer. Similar considerations are shown for the SHX along with assumptions for flow mechanics and resulting model methods for sublimation in a flow.

Bower, Chad↗