Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface tension”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Electroelastic investigation of drying rate in the direct contact ultrasonic fabric dewatering process

Ultrasonic vibrations, used to atomize liquids into a fine mist, are a promising solution for the future of efficient clothes drying technology. The world’s first ultrasonic dryer—demonstrated by researchers at Oak Ridge National Laboratory—successfully applies the scientific principles behind ultrasonic drying, and several working prototypes have been demonstrated. This technology is based on direct mechanical coupling between mesh piezoelectric transducers and wet fabric. During the atomization process, vertical oscillations of a contained liquid, called Faraday excitations, result in the formation of standing waves on the liquid surface. At increasing amplitudes and frequencies of oscillation, wave peaks become extended and form “necks” connecting small secondary droplets to the bulk liquid. When the oscillation reaches an acceleration threshold, the droplet momentum is sufficient to break the surface tension of the neck and enable the droplets to travel away from the liquid. In this work, we investigate the atomization process using an ultrasonic transducer as it pertains to moisture retained within a fabric. An experimentally validated electromechanical analytical-numerical model is proposed. This model bridges the vibrations of a piezoelectric mesh transducer to the critical acceleration needed for fabric drying to occur. Then, the drying rate model is developed, consisting of an initial nonlinear region due to atomization, followed by a linear thermal evaporation region. The models developed identify the influence of key parameters on ultrasonic drying and will aid in improving atomizer design for efficient, timely fabric drying. This study is the first proposed model for the ultrasonic atomization of fabrics saturated with water, applicable to any type of transducer. The results present a non-dimensional equation for the ultrasonic dewatering of fabrics, dependent only on transducer acceleration and the surface area of the cloth. Furthermore, the development of this technology using the proposed physical models will allow for global reductions in electrical demand related to clothes drying.

42 ENGINEERING↗

Characterization of Ice Roughness Variations in Scaled Glaze Icing Conditions

Because of the significant influence of surface tension in governing the stability and breakdown of the liquid film in flooded stagnation regions of airfoils exposed to glaze icing conditions, the Weber number is expected to be a significant parameter governing the formation and evolution of ice roughness. To investigate the influence of the Weber number on roughness formation, 53.3-cm (21-in.) and 182.9-cm (72-in.) NACA 0012 airfoils were exposed to flow conditions with essentially the same Weber number and varying stagnation collection efficiency to illuminate similarities of the ice roughness created on the different airfoils. The airfoils were exposed to icing conditions in the Icing Research Tunnel (IRT) at the NASA Glenn Research Center. Following exposure to the icing event, the airfoils were then scanned using a ROMER Absolute Arm scanning system. The resulting point clouds were then analyzed using the self-organizing map approach of McClain and Kreeger (2013) to determine the spatial roughness variations along the surfaces of the iced airfoils. The roughness characteristics on each airfoil were then compared using the relative geometries of the airfoil. The results indicate that features of the ice shape and roughness such as glaze-ice plateau limits and maximum airfoil roughness were captured well by Weber number and collection efficiency scaling of glaze icing conditions. However, secondary ice roughness features relating the instability and waviness of the liquid film on the glaze-ice plateau surface are scaled based on physics that were not captured by the local collection efficiency variations.

Roughness Formation↗

Thermally-induced transition of lamellae orientation in block-copolymer films on ‘neutral’ nanoparticle-coated substrates

Block-copolymer orientation in thin films is controlled by the complex balance between interfacial free energies, including the inter-block segregation strength, the surface tensions of the blocks, and the relative substrate interactions. While block-copolymer lamellae orient horizontally when there is any preferential affinity of one block for the substrate, we recently described how nanoparticle-roughened substrates can be used to modify substrate interactions. We demonstrate how such ‘neutral’ substrates can be combined with control of annealing temperature to generate vertical lamellae orientations throughout a sample, at all thicknesses. We observe an orientational transition from vertical to horizontal lamellae upon heating, as confirmed using a combination of atomic force microscopy (AFM), neutron reflectometry (NR) and rotational small-angle neutron scattering (RSANS). Using molecular dynamics (MD) simulations, we identify substrate-localized distortions to the lamellar morphology as the physical basis of the novel behavior. In particular, under strong segregation conditions, bending of horizontal lamellae induce a large energetic cost. At higher temperatures, the energetic cost of conformal deformations of lamellae over the rough substrate is reduced, returning lamellae to the typical horizontal orientation. Thus, we find that both surface interactions and temperature play a crucial role in dictating block-copolymer lamellae orientation. As a result, our combined experimental and simulation findings suggest that controlling substrate roughness should provide a useful and robust platform for controlling block-copolymer orientation in applications of these materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Application of the core shell model for strengthening polymer filament interfaces

While surface segregation has been intensively studied in thin films, relatively little has been investigated in filament geometries. In contrast to thin films, the filament surface forms a continuum, with interactions both at the free air and internal filament interface, which makes it difficult to achieve an equilibrium configuration. This asymmetry has become particularly apparent with the increasing use of additive manufacturing where entire structures are constructed via layered deposition of filamentous layers from a moving thermal nozzle. In addition, this process is highly non-equilibrated with poor thermal retention and is responsible for insufficient filament–filament interfacial fusion and internal pore formation along the printing direction. These features all contribute to poor mechanical and structural properties, which are exacerbated in semi-crystalline polymers, such as Polylactic Acid (PLA), where the melting point, T m , is much higher than the glass transition, T g . Even though system is liquid the molecules become ordered within the crystal structure and this ordering interferes with interdiffusion, which in turn prevents proper interfacial fusion. Capitalizing on the differential in surface tension, we show that addition of less than 1%, or trace amounts, of longer chain polymers, an oriented core shell structure, will be formed with a self-limiting thickness of three time the radius of gyration, R g , of the tracer chains. The lower T g of the tracers and their orientation makes them poised for interdiffusion when subsequent layers are deposited producing structures with significant improvement of the mechanical properties and internal structural integrity.

36 MATERIALS SCIENCE↗

Detached Bridgman Growth of Germanium and Germanium-Silicon Alloy Crystals

Earth based experiments on the science of detached crystal growth are being conducted on germanium and germanium-silicon alloys (2at% Si average composition) in preparation for a series of experiments aboard the International Space Station (ISS) to differentiate among proposed mechanisms contributing to detachment. Sessile drop measurements were first carried out for a large number of substrates made of potential ampoule materials to determine the contact angles and the surface tension as a function of temperature and composition. The process atmosphere and duration of the experiment (for some cases) were also found to have significant influence on the wetting angle. Growth experiments have used pyrolytic boron nitride (pBN) and fused silica ampoules with the majority of the detached results occurring predictably in the pBN. The contact angles were 173 deg (Ge) and 165 deg (GeSi) for pBN. For fused silica, the contact angle decreases to an equilibrium value with duration of measurement ranging from 150 to 117 deg (Ge), 129 to 100 deg (GeSi). Forming gas (Ar + 2% H2) and vacuum have been used in the growth ampoules. With gas in the ampoule, a variation of the temperature profile during growth has been used to control the pressure difference between the top of the melt and the volume below the melt caused by detachment of the growing crystal. The stability of detachment has been modeled and substantial insight has been gained into the reasons that detachment has most often been observed in reduced gravity but nonetheless has occurred randomly even there. An empirical model for the conditions necessary to achieve sufficient stability to maintain detached growth for extended periods has been developed and will be presented. Methods for determining the nature and extent of detachment include profilometry and optical and electron microscopy. This surface study is the subject of another presentation at this Congress. Results in this presentation will show that we have established the effects of different ampoule materials, temperature profiles, pressure differences, and silicon concentrations and that samples that are nearly completely detached can be grown repeatedly.

Szofran, F. R.↗

Microgravity Passive Phase Separator

A new invention disclosure discusses a structure and process for separating gas from liquids in microgravity. The Microgravity Passive Phase Separator consists of two concentric, pleated, woven stainless- steel screens (25-micrometer nominal pore) with an axial inlet, and an annular outlet between both screens (see figure). Water enters at one end of the center screen at high velocity, eventually passing through the inner screen and out through the annular exit. As gas is introduced into the flow stream, the drag force exerted on the bubble pushes it downstream until flow stagnation or until it reaches an equilibrium point between the surface tension holding bubble to the screen and the drag force. Gas bubbles of a given size will form a front that is moved further down the length of the inner screen with increasing velocity. As more bubbles are added, the front location will remain fixed, but additional bubbles will move to the end of the unit, eventually coming to rest in the large cavity between the unit housing and the outer screen (storage area). Owing to the small size of the pores and the hydrophilic nature of the screen material, gas does not pass through the screen and is retained within the unit for emptying during ground processing. If debris is picked up on the screen, the area closest to the inlet will become clogged, so high-velocity flow will persist farther down the length of the center screen, pushing the bubble front further from the inlet of the inner screen. It is desired to keep the velocity high enough so that, for any bubble size, an area of clean screen exists between the bubbles and the debris. The primary benefits of this innovation are the lack of any need for additional power, strip gas, or location for venting the separated gas. As the unit contains no membrane, the transport fluid will not be lost due to evaporation in the process of gas separation. Separation is performed with relatively low pressure drop based on the large surface area of the separating screen. Additionally, there are no moving parts, and there are no failure modes that involve fluid loss. A patent application has been filed.

Paragano, Matthew↗

Computations of Boiling in Microgravity

The absence (or reduction) of gravity, can lead to major changes in boiling heat transfer. On Earth, convection has a major effect on the heat distribution ahead of an evaporation front, and buoyancy determines the motion of the growing bubbles. In microgravity, convection and buoyancy are absent or greatly reduced and the dynamics of the growing vapor bubbles can change in a fundamental way. In particular, the lack of redistribution of heat can lead to a large superheat and explosive growth of bubbles once they form. While considerable efforts have been devoted to examining boiling experimentally, including the effect of microgravity, theoretical and computational work have been limited. Here, the growth of boiling bubbles is studied by direct numerical simulations where the flow field is fully resolved and the effects of inertia, viscosity, surface deformation, heat conduction and convection, as well as the phase change, are fully accounted for. Boiling involves both fluid flow and heat transfer and thus requires the solution of the Navier-Stokes and the energy equations. The numerical method is based on writing one set of governing transport equations which is valid in both the liquid and vapor phases. This local, single-field formulation incorporates the effect of the interface in the governing equations as source terms acting only at the interface. These sources account for surface tension and latent heat in the equations for conservation of momentum and energy as well as mass transfer across the interface due to phase change. The single-field formulation naturally incorporates the correct mass, momentum and energy balances across the interface. Integration of the conservation equations across the interface directly yields the jump conditions derived in the local instant formulation for two-phase systems. In the numerical implementation, the conservation equations for the whole computational domain (both vapor and liquid) are solved using a stationary grid and the phase boundary is followed by a moving unstructured two-dimensional grid. While two-dimensional simulations have been used for preliminary studies and to examine the resolution requirement, the focus is on fully three-dimensional simulations. The numerical methodology, including the parallelization and grid refinement strategy is discussed, and preliminary results shown. For buoyancy driven flow, the heat transfer is in good agreement with experimental correlations. The changes when gravity is turned off and/or fluid shear is added are discussed, as well as the difference between simulations of a layer freely releasing bubbles versus simulations using only one wavelength initial perturbation. Figure 1 shows the early stages of the formation of a three-dimensional bubble from a thin vapor layer. The boundary conditions are periodic in the x and y direction, the bottom is a hot and the top allows a free outflow. The jagged edge of the surface close to the bottom of the computational domain is due to some of the surface elements being on the other side of the domain and some elements not plotted by our plotting routine. In the second figure, we show the temperature distribution through two perpendicular planes.

Tryggvason, G.↗

Multimodal imaging of oil-in-water bilgewater emulsion and biofilms

Bilgewater emulsions, consisting of oil and surfactant mixtures in water, affect many aquatic species. Thus development of methods and techniques to treat or mitigate the formation and undesired consequences of shipboard emulsions are urgently needed. This work presents new results of the evolution of the bilgewaer chemical and physical properties using in situ imaging. A Navy O/W emulsion consisting of three oils and a detergent mixture was used as the synthetic bilgewater model [1, 2]. Synthetic oil-in-water (O/W) emulsion droplets were seled in a vacuum compatible microfluidic sample holder and imaged using a suite of tools including scanning electron microscopy (SEM), time-of-flight secondary ion mass spectrometry (ToF-SIMS), confocal laser scanning microscopy, and optical microscopy, highlighting the advantage of multiscale analysis and its applications in waste reduction and treatment in the environment. The transferrable and vacuum compatible microfluidic interface, System for Analysis at the Liquid Vacuum Interface (SALVI), was used in this study. SALVI enabled surface analysis of liquids and liquid-solid interactions using ToF-SIMS and SEM [3, 4]. Its detection window is an aperture of 2 ?m in diameter open to vacuum, permitting direct detection of the liquid surface. Liquid is withheld by surface tension within the aperture. The interface is composed of a silicon nitride membrane and polydimethylsiloxane microchannel [3, 4]. A variety of samples including complex liquid mixtures, ionic liquids, single mammalian cells, live biofilms, and solid-electrolyte interface have been analyzed using in situ imaging [5, 6]. The feasibility of using SALVI for in situ SEM imaging of nanoparticles and colloids in liquid was recently demonstrated [7]. This paper shows new findings of multimodal imaging and analysis of synthesized emulsion particles in water. Figure 1 depicts a schematic of multimodal in situ imaging of bilgewater emulsion using SEM and ToF-SIMS. Furthermore, we study the interactions of microbes and bilgewater emulsion. Microbes play an important role in the ocean. We hypothesize that microbes release organics that can act as surfactants that affect bilgewater formation or weakening. We present the first systematic study of emulsions and biofilms and investigate the effects of biofilms on bilgewater emulsions. Pseudomonas was selected as a model strain. Biofilms were cultured in a microchannel to allow culture [8]. Once a thick layer of biofilms was formed, the medium solution was changed to a mixture consisting of 50 % bilgewater emulsion. Dispersed biofilms were collected at 24 hrs. and 48 hrs. after emulsions were introduced into the channel. Bilgewater emulsions, biofilms, and mixtures of bilgewater emulsions and biofilms were analyzed using multiple in situ and ex situ techniques as described earlier. Our findings indicate that biofilms change the chemical makeup of the emulsion surface compositions and emulsion droplet size distribution, confirming the hypothesis that extracellular polymeric substance (EPS) related components released from biofilms can function as surfactants and change the oil-in-water interfaces.

bilgewater, multimodal imaging, biofilms↗

Peptide assembly-driven metal-organic framework (MOF) motors for micro electric generators

Peptide–metal–organic framework (Pep-MOF) motors, whose motions are driven by anisotropic surface tension gradients created via peptide self-assembly around frameworks, can rotate microscopic rotors and magnets fast enough to generate an electric power of 0.1 μW. Finally, a new rigid Pep-MOF motor can be recycled by refilling the peptide fuel into the nanopores of the MOF.

36 MATERIALS SCIENCE↗

High Miscibility Compatible with Ordered Molecular Packing Enables an Excellent Efficiency of 16.2% in All-Small-Molecule Organic Solar Cells

In all-small-molecule organic solar cells (ASM-OSCs), a high short-circuit current (Jsc) usually needs a small phase separation, while a high fill factor (FF) is generally realized in a highly ordered packing system. However, small domain and ordered packing always conflicted each other in ASM-OSCs, leading to a mutually restricted J sc and FF. Here, in this study, alleviation of the previous dilemma by the strategy of obtaining simultaneous good miscibility and ordered packing through modulating homo- and heteromolecular interactions is proposed. By moving the alkyl-thiolation side chains from the para- to the meta-position in the small-molecule donor, the surface tension and molecular planarity are synchronously enhanced, resulting in compatible properties of good miscibility with acceptor BTP-eC9 and strong self-assembly ability. As a result, an optimized morphology with multi-length-scale domains and highly ordered packing is realized. The device exhibits a long carrier lifetime (39.8 μs) and fast charge collection (15.5 ns). A record efficiency of 16.2% with a high FF of 75.6% and a J sc of 25.4 mA cm –2 in the ASM-OSCs is obtained. These results demonstrate that the strategy of simultaneously obtaining good miscibility with high crystallinity could be an efficient photovoltaic material design principle for high-performance ASM-OSCs.

14 SOLAR ENERGY↗

Breakage of wet flexible fiber agglomerates impacting a plane

Abstract The breakage of an agglomerate of wet flexible fibers impacting a plane is computationally investigated in this work using the discrete element method. In the agglomerate, the fibers stick together due to cohesive liquid bridge forces. Agglomerate breakage with various impact conditions, initial configurations, fiber properties, and liquid bridge properties is systematically investigated. The degree of breakage is governed by the impact energy, the cohesion energy due to liquid bridges, the energy dissipation/absorption through fiber–fiber contacts and fiber deformation, and the efficiency of force transmission within the agglomerate. More specifically, breakage is promoted by increasing impact velocity, decreasing agglomerate size, increasing initial compaction, increasing fiber bending modulus, decreasing liquid surface tension, and decreasing liquid‐to‐solid volume ratio. Breakage is strongly dependent on the modified Weber number, that is, the ratio of the Weber number to a dimensionless rupture distance, which is a measure of the impact energy relative to the cohesion energy.

Yang, Jiecheng↗

Foaming prediction in pure liquids from dimensionless numbers inspired by the theory of fluid behavior for drops

Foaming prediction is critical for selecting materials and designing processes in industries such as bioprocessing and gas processing. Existing models lack the generality needed for a wide range of materials and overlook the foaming behavior in pure liquids. Here, this work presents a novel method for predicting foaming in pure liquids based on their density, surface tension, and viscosity, using Reynolds ( Re ) and Ohnesorge ( Oh ) numbers. A foaming prediction map, leveraging the theory of fluid drop behavior, was developed by plotting these numbers. This map delineates distinct non-foaming and foaming regions, functioning as a binary classifier for foaming predictions. The map was fitted and validated through shake test experiments on 46 liquids, demonstrating reliable predictions, except for a specific region characterized by small Oh and large Re numbers. This region corresponded to relatively low foam stability and high turbulence, making foaming predictions challenging for liquids in this category.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Upcycling of Waste Plastics into Carboxylic Acids for Biodegradable Surfactants

This work outlines a process for producing high‐purity (>95%) carboxylate surfactants from post‐consumer recycled high‐density polyethylene (PCR‐HDPE). The approach involves the thermal depolymerization of PCR‐HDPE via pyrolysis, followed by fractional distillation to isolate C9–C14 olefins. These olefins undergo hydroformylation using cobalt carbonyl catalysts to generate aldehydes, which are subsequently oxidized to carboxylic acids using Pinnick oxidation under mild aqueous‐phase conditions. Neutralization of the resulting carboxylic acids with sodium hydroxide produces plastic‐derived carboxylate surfactants (PDCs) in the form of sodium carboxylates. Subsequent purification steps ensure surfactant‐grade purity and enable accurate assessment of physicochemical properties. The resulting PDCs are evaluated for critical micelle concentration (CMC), foamability, surface tension reduction, and calcium ion tolerance, demonstrating competitive behavior with conventional anionic carboxylate surfactants. This route provides a sustainable alternative for surfactant production, reducing reliance on fossil‐derived feedstocks and valorizing plastic waste streams through chemical upcycling.

Biodegradable surfactants↗

A micro-jet array for economic intensification of gas transfer in bioreactors

Bioreactors are of interest for gas-to-liquid conversion of stranded or waste industrial gases, such as CO, CH 4 , or syngas. Process economics requires reduction of bioreactor cost and size while maintaining intense production via rapid delivery of gases to the liquid phase (i.e., high k L a). Here, we show a novel bioreactor design that outperforms all known technology in terms of gas transfer energy efficiency (k L a per power density) while operating at high k L a (i.e., near 0.8 s -1 ). The reactor design uses a micro-jet array to break feedstock gas into a downward microbubble flow. Hydrodynamic and surfactant measurements show the reactor's advanced performance arises from its bubble breakage mechanism, which limits fluid shear to a thin plane located at an optimal location for bubble breakage. Power dissipation and k L are shown to scale with micro-jet diameter rather than reactor diameter, and the micro-jet array achieves improved performance compared to classical impinging-jets, ejector, or U-loop reactors. Additionally, the hydrodynamic mechanism by which the micro-jets break bubbles apart is shown to be shearing the bubbles into filaments then fragmentation by surface tension rather than “cutting in half” of bubbles. Guided by these hydrodynamic insights, strategies for industrial design are given.

09 BIOMASS FUELS↗

Liquid Metals for Advanced Batteries: Recent Progress and Future Perspective

ABSTRACT The shift toward sustainable energy has increased the demand for efficient energy storage systems to complement renewable sources like solar and wind. While lithium‐ion batteries dominate the market, challenges such as safety concerns and limited energy density drive the search for new solutions. Liquid metals (LMs) have emerged as promising materials for advanced batteries due to their unique properties, including low melting points, high electrical conductivity, tunable surface tension, and strong alloying tendency. Enabled by the unique properties of LMs, four key scientific functions of LMs in batteries are highlighted: active materials, self‐healing, interface stabilization, and conductivity enhancement. These applications can improve battery performance, safety, and lifespan. This review also discusses current challenges and future opportunities for using LMs in next‐generation energy storage systems. image

Zheng, Tianrui [Materials Science and Engineering ↗

Incompressible multiphase flow and encapsulation simulations using the moment-of-fluid method

A moment-of-fluid method is presented for computing solutions to incompressible multiphase flows in which the number of materials can be greater than two. In this work, the multimaterial moment-of-fluid interface representation technique is applied to simulating surface tension effects at points where three materials meet. The advection terms are solved using a directionally split cell integrated semi-Lagrangian algorithm, and the projection method is used to evaluate the pressure gradient force term. The underlying computational grid is a dynamic block-structured adaptive grid. The new method is applied to multiphase problems illustrating contact-line dynamics, triple junctions, and encapsulation in order to demonstrate its capabilities. Examples are given in two-dimensional, three-dimensional axisymmetric (R–Z), and three-dimensional (X–Y–Z) coordinate systems.

97 MATHEMATICS AND COMPUTING↗

Improving the reliability of machine learned potentials for modeling inhomogeneous liquids

The atomic-scale response of inhomogeneous fluids at interfaces and surrounding solute particles plays a critical role in governing chemical, electrochemical, and biological processes. Classical molecular dynamics simulations have been applied extensively to simulate the response of fluids to inhomogeneities directly, but are limited by the accuracy of the underlying interatomic potentials. Here, we use neural network potentials (NNPs) trained to ab initio simulations to accurately predict the inhomogeneous responses of two distinct fluids: liquid water and molten NaCl. Although NNPs can be readily trained to model complex bulk systems across a range of state points, we show that to appropriately model a fluid's response at an interface, relevant inhomogeneous configurations must be included in the training data. In order to sufficiently sample appropriate configurations of such inhomogeneous fluids, we develop protocols based on molecular dynamics simulations in the presence of external potentials. We demonstrate that NNPs trained on inhomogeneous fluid configurations can more accurately predict several key properties of fluids—including the density response, surface tension and size-dependent cavitation free energies—for liquid water and molten NaCl, compared to both empirical interatomic potentials and NNPs that are not trained on such inhomogeneous configurations. This work therefore provides a first demonstration and framework to extract the response of inhomogeneous fluids from first principles for classical density-functional treatment of fluids free from empirical potentials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗