Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The effect of yield strength and ductility to fatigue damage

The cumulative damage of aluminium alloys with different yield strength and various ductility due to seismic loads was studied. The responses of an idealized beam with a centered mass at one end and fixed at the other end to El Centro's and Taft's earthquakes are computed by assuming that the alloys are perfectly elastoplastic materials and by using numerical technique. Consequently, the corresponding residual plastic strain can be obtained from the stress-strain relationship. The revised Palmgren-Miner cumulative damage theorem is utilized to calculate the fatigue damage. The numerical results show that in certain cases, the high ductility materials are more resistant to seismic loads than the high yield strength materials. The results also show that if a structure collapse during the earthquake, the collapse always occurs in the very early stage.

Yeh, H. Y.↗
NASA NTRS1973

An investigation of the compressive strength of PRD-49-3/Epoxy composites

The development of unidirectional fiber composite materials is discussed. The mechanical and physical properties of the materials are described. Emphasis is placed in analyzing the compressive behavior of composite materials and developing methods for increasing compressive strength. The test program for evaluating the various procedures for improving compressive strength are reported.

Kulkarni, S. V.↗
NASA NTRS1973

Oscillator strengths for the X/1 Sigma+/ - A/1 Pi/ system of CH+.

Oscillator strengths for the X/1 Sigma+/ - A/1 Pi/ system of CH+ computed to an estimated accuracy of 10 percent from ab initio wave functions are presented. These oscillator strength values are given for the two strongest interstellar lines of 4232 and 3957 A.

Yoshimine, M.↗
NASA NTRS1972

Factors affecting the strength of multipass low-alloy steel weld metal

The mechanical properties of multipass high-strength steel weld metals depend upon several factors, among the most important being: (1) The interaction between the alloy composition and weld metal cooling rate which determines the as-deposited microstructure; and (2) the thermal effects of subsequent passes on each underlying pass which alter the original microstructure. The bulk properties of a multipass weld are therefore governed by both the initial microstructure of each weld pass and its subsequent thermal history. Data obtained for a high strength low alloy steel weld metal confirmed that a simple correlation exists between mechanical properties and welding conditions if the latter are in turn correlated as weld cooling rate.

Krantz, B. M.↗
NASA NTRS1974

Compressive strength of fiber reinforced composite materials

Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes, and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed, delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

Davis, J. G., Jr.↗
NASA NTRS1974

Hydrogen adsorption and diffusion, and subcritical-crack growth in high-strength steels and nickel base alloys

Coordinated studies of the kinetics of crack growth and of hydrogen adsorption and diffusion were initiated to develop information that is needed for a clearer determination of the rate controlling process and possible mechanism for hydrogen enhanced crack growth, and for estimating behavior over a range of temperatures and pressures. Inconel 718 alloy and 18Ni(200) maraging steel were selected for these studies. 18Ni(250) maraging steel, 316 stainless steel, and iron single crystal of (111) orientation were also included in the chemistry studies. Crack growth data on 18Ni(250) maraging steel from another program are included for comparison. No sustained-load crack growth was observed for the Inconel 718 alloy in gaseous hydrogen. Gaseous hydrogen assisted crack growth in the 18Ni maraging steels were characterized by K-independent (Stage 2) extension over a wide range of hydrogen pressures (86 to 2000 torr or 12 kN/m2 to 266 kN/m2) and test temperatures (-60 C to +100 C). The higher strength 18Ni(250) maraging steel was more susceptible than the lower strength 200 grade. A transition temperature was observed, above which crack growth rates became diminishingly small.

Wei, R. P.↗
NASA NTRS1973

Combined effects of weld-induced residual stresses and flaws on the fracture strength of Ti-5Al-2.5Sn

The combined effects of weld-induced residual stresses and flaws on fracture strength were experimentally evaluated by testing Ti-5Al-2.5Sn surface flawed specimens at -320F (-195C) in liquid nitrogen. Flaws were located in weld metal with crack planes either parallel to or perpendicular to gas tungsten arc weld centerlines, and in base metal with the crack plane perpendicular to the rolling direction. Tests were conducted using two different flaw sizes to effect fracture stresses at two different levels including one level either at or near, and one level well below the tensile yield strength. Three different residual stress levels were generated, measured, and tested. Results were evaluated using modified linear elastic fracture mechanics theory.

Hall, L. R.↗
NASA NTRS1975

Aluminum alloys with improved strength

Mechanical strength and stress corrosion of new BAR and 7050 alloys that include Zn instead of Cr have been studied and compared with those of 7075 aluminum alloy. Added mechanical strength of new alloys is attributed to finer grain size of 5 to 8 micrometers, however, susceptibility to stress corrosion attack is increased.

Deiasi, R.↗
NASA NTRS1974

The resistance to embrittlement by a hydrogen environment of selected high strength iron-manganese base alloys

Fe-16Mn and Fe-25Mn base alloys, which had been cold worked to yield strength levels of 201 and 178 KSI, were resistant to degradation of mechanical properties in a one atmosphere hydrogen environment at ambient temperature under the loading conditions employed in this investigation. Transmission electron microscopy established that bands of epsilon phase martensite and fcc mechanical twins were formed throughout the fcc matrix when these alloys were cold worked. In the cold worked alloys a high density of crystal defects were observed associated with both types of strain induced structures, which should contribute significantly to the strengthening of these alloys. High strength iron base alloys can be produced which appear to have some resistance to degradation of mechanical properties in a hydrogen environment under certain conditions.

Benson, R. B., Jr.↗
NASA NTRS1975

Investigation to develop a method to apply diffusion barrier to high strength fibers

A radio frequency powered ion plating process was used to apply the diffusion barriers of aluminum oxide, yttrium oxide, hafnium oxide and titanium carbide to a substrate tungsten fiber. Each of the coatings was examined as to its effect on both room temperature strength and tensile strength of the base tungsten fiber. The coated fibers were then overcoated with a nickel alloy to become single cell diffusion couples. These diffusion couples were exposed to 1093 C for 24 hours, cycled between room temperature and 1093 C, and given a thermal anneal for 100 hours at 1200 C. Tensile testing and metallographic examinations determined that the hafnium oxide coating produced the best high temperature diffusion barrier for tungsten of the four coatings.

Veltri, R. D.↗
NASA NTRS1970

Development of advanced high strength tantalum base alloys. Part 2: Scale-up investigation

Three experimental tantalum alloy compositions containing 14-16% W, 1% Re, 0.7% Hf, 0.025% C or 0.015% C and 0.015% N were prepared as two inch diameter ingots by consumable electrode vacuum arc melting. The as-cast ingots were processed by extrusion and swaging to one inch and 0.4 inch diameter rod and evaluated. Excellent high temperature forging behavior was exhibited by all three compositions. Creep strength at 2000 F to 2400 F was enhanced by higher tungsten additions as well as substitution of nitrogen for carbon. Weldability of all three compositions was determined to be adequate. Room temperature ductility was retained in the advanced tantalum alloy compositions as well as a notched/unnotched strength ratio of 1.4 for a notched bar having a K sub t = 2.9.

Ammon, R. L.↗
NASA NTRS1974

Investigation of the plastic fracture of high-strength aluminum alloys

In a study of plastic fracture in five high-strength aluminum alloys (2014, 2024, 2124, 7075, and 7079), it has been shown that fracture toughness is affected primarily by the size and volume fraction of the larger (2 to 10 microms) second-phase particles. Certain of these particles crack at small plastic strains, nucleating voids which, with further plastic strain, coalesce to cause fracture. Not all second-phase particles crack at small plastic strains, and qualitative analysis of those which are primarily responsible for void nucleation shows that they contain iron or silicon or both. This result suggests that a reduction in the iron and silicon impurity content of the alloys should improve fracture toughness without loss of strength.

Van Stone, R. H.↗
NASA NTRS1974

Methods for investigating the strength characteristics of a lunar soil simulant

A lunar soil simulant was used in research on predicting the performance of the Lunar Roving Vehicle (LRV) on the moon. The simulant was prepared from ground basaltic rock whose grain size distribution was matched to the lunar soil samples collected by Apollo 11 and 12. The strength characteristics of the simulant, i.e., internal friction angle, cohesion, and cone penetration resistance, were tested in triaxial tests, trenching tests, and cone penetration resistance tests. Subsequent soil tests and LRV performance on the moon proved that the lunar soil strength characteristics could be successfully simulated.-

Melzer, K.-J.↗
NASA NTRS1974

Micromechanics strength theories

The available micromechanics theories for predicting the uniaxial strengths of unidirectional composites are described. The theories presuppose that the required properties of the constituents of the composites are known and that the uniaxial loads are coincident with the principal axes of the unidirectional composite. The uniaxial strengths considered are those required to resist either in-plane loads, flexural (bending), or horizontal-beam shear. The discussion deals primarily with fiber-nonmetallic matrix composites where all the fibers are parallel and lie in the same plane. However, the micromechanics theories presented here are transferable to fiber-metallic matrix composites so long as the underlying assumptions are not violated. Some of the concepts described herein may also be applicable to particulate composites.

Chamis, C. C.↗
NASA NTRS1974

Tensile properties of an ultrahigh-strength graphite fiber in an epoxy matrix

The fiber performance and reinforcement potential for fiber composites of a special PAN-based graphite fiber were evaluated by testing the fiber's tensile properties in an epoxy matrix. Representative strand samples were taken from 30 spools of single-end, 1500-filament fiber to make over 5000 fiber/epoxy strand specimens using the filament-winding process. Characteristics studied were fiber uniformity, strength and modulus distributions at room and liquid-nitrogen temperatures, stress-strain behavior, the effect of strain rate on fiber strength, and acoustic emission during tensile loading to failure. The fiber was found to have a 3570-MPa failure stress, a 1.7% failure strain, a 206-GPa modulus, and a density of 1.77 Mg/cu m at 23 C. Liquid-nitrogen temperature and various strain rates had no significant effect on fiber tensile properties.

Chiao, T. T.↗
NASA NTRS1976

Estimation of Ksub Ic from slow bend precracked Charpy specimen strength ratios

Strength ratios are reported which were derived from slow bend tests on 0.25 inch thick precracked Charpy specimens of steels, aluminum alloys, and a titanium alloy for which valid K sub Ic values were established. The strength ratios were used to develop calibration curves typical of those that could be useful in estimating K sub Ic for the purposes of alloy development of quality control.

Succop, G.↗
NASA NTRS1975

Compressive strength of fiber-reinforced composite materials

Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed - delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

Davis, J. G., Jr.↗