Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Post-Flight Quantification of LOFTID Aeroshell Deflection Using Feature Tracking

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was a flight demonstration of the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology, which has the potential to enable delivery of heavy payloads to Mars, Venus, and Titan, as well as return to Earth. Unlike rigid aeroshells that are constrained by the diameter of the launch vehicle shroud, inflatable aeroshells can be deployed to a much larger drag area, thus allowing a more massive spacecraft to begin its deceleration at higher altitudes and experience less heating. On November 10, 2022, the LOFTID reentry vehicle launched aboard a United Launch Alliance Atlas V rocket to low-Earth orbit. The aeroshell was inflated to its full 6-meter diameter, and the vehicle then successfully re-entered the atmosphere, landing in the Pacific Ocean. The aeroshell was composed of seven tori bound together by high strength straps to create a 70-degree half-angle sphere-cone, and the forebody was covered with a flexible thermal protection system (FTPS) (Fig. 1). The centerbody of the vehicle housed six visual cameras. Each camera was made up of 1920 x 1080 pixels and had a field-of-view (FOV) of 85.4° x 55.6°, resulting in a resolution of less than 0.1" at all locations on the aftbody side of the aeroshell. The approximate locations of the cameras and their associated FOVs is shown in Fig. 2. The high loads experienced during flight resulted in the cone of the aeroshell deflecting. This behavior was seen during the static load testing of the aeroshell in May 2021, in which loads ranging from 1,000 to 20,000 lbf were applied, and deflections of up to ~1.7° were observed. The LOFTID team was interested in estimating the deflection of the aeroshell during the its entry into Earth's atmosphere. Before launch, 1"-diameter black circles were drawn on select structural straps for tracking with the visual cameras; the change in position of these features could then be used to calculate aeroshell deflection angle.

Hannah S. Alpert↗
NASA NTRSDate not supplied

Post-Flight Quantification of LOFTID Aeroshell Deflection Using Feature Tracking

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was a flight demonstration of the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology, which has the potential to enable delivery of heavy payloads to Mars, Venus, and Titan, as well as return to Earth. Unlike rigid aeroshells that are constrained by the diameter of the launch vehicle shroud, inflatable aeroshells can be deployed to a much larger drag area, thus allowing a more massive spacecraft to begin its deceleration at higher altitudes and experience less heating. On November 10, 2022, the LOFTID reentry vehicle launched aboard a United Launch Alliance Atlas V rocket to low-Earth orbit. The aeroshell was inflated to its full 6-meter diameter, and the vehicle then successfully re-entered the atmosphere, landing in the Pacific Ocean. The aeroshell was composed of seven tori bound together by high strength straps to create a 70-degree half-angle sphere-cone, and the forebody was covered with a flexible thermal protection system (FTPS) (Fig. 1). The centerbody of the vehicle housed six visual cameras. Each camera was made up of 1920 x 1080 pixels and had a field-of-view (FOV) of 85.4° x 55.6°, resulting in a resolution of less than 0.1" at all locations on the aftbody side of the aeroshell. The approximate locations of the cameras and their associated FOVs is shown in Fig. 2. The high loads experienced during flight resulted in the cone of the aeroshell deflecting. This behavior was seen during the static load testing of the aeroshell in May 2021, in which loads ranging from 1,000 to 20,000 lbf were applied, and deflections of up to ~1.7° were observed. The LOFTID team was interested in estimating the deflection of the aeroshell during the its entry into Earth's atmosphere. Before launch, 1"-diameter black circles were drawn on select structural straps for tracking with the visual cameras; the change in position of these features could then be used to calculate aeroshell deflection angle.

Hannah S. Alpert↗
NASA NTRS2012

Test Analysis Correlation of the Single Stringer Bending Tests for the Space Shuttle ET-137 Intertank Stringer Crack Investigation

On November 5, 2010, Space Shuttle mission STS-133 was scrubbed due to a hydrogen leak at the Ground Umbilical Carrier Plate (GUCP). After the scrub, a crack in the foam thermal protection system (TPS) was observed on the External Tank (ET) near the interface between the liquid oxygen (LOX) tank and the Intertank. When the damaged foam was removed, two 9-in. long cracks were found on the feet of Intertank stringer S7-2, and the stringer failure was the cause of the TPS crack. An investigation was conducted to determine the root cause of the cracks, establish a remedy/repair for the stringers, and provide flight rationale for the damaged tank, ET-137. The Space Transportation System (STS) Super Lightweight ET (SLWT) is comprised of two propellant tanks (an aft liquid hydrogen (LH2) tank and a forward LOX tank) and an Intertank. The Intertank serves as the structural connection between the two propellant tanks and also functions to receive and distribute all thrust loads from the solid rocket boosters . The Intertank is a stiffened cylinder structure consisting of eight mechanically joined panels (two integrally-stiffened, machined thrust panels to react the booster loads and six stringer-stiffened skin panels). There are one main ring frame, four intermediate ring frames, and forward and aft flange chords that mate to the respective propellant tanks.. The skin/stringer panels utilize external hat-section stringers that are mechanically attached with rivets along most of their length and with specialty fasteners, such as GP Lockbolts and Hi-Loks, at the forward and aft ends where the stringers attach to the flange chords. During the STS-133 Intertank stringer crack investigation, cracks were found on a total of five stringers. All of the cracks were at the LOX end, in the feet of the stringers, and near the forward fasteners (GP Lockbolts). Video of tanking for the November 5 launch attempt was used to determine that the TPS failure, and thus the stringer failure, occurred as the LOX liquid level crossed the LOX tank / Intertank interface ring frame. Hence, cryogenically-induced displacements were suspected as a contributing cause of the stringer cracks. To study the behavior of Intertank stringers subjected to similar displacements, static load tests of individual stringers, colloquially known as "single stringer bending tests" were performed. Approximately thirty stringers were tested, many of which were cut from the partially completed Intertank for what would have been ET-139. In addition to the tests, finite element (FE) analyses of the test configuration were also performed. In this paper, the FE analyses and test-analysis correlation for stringer test S6-8 are presented. Stringer S6-8 is a "short chord" configuration with no doubler panels.

Phillips, Dawn R.↗
NASA NTRS1962

DEVELOPMENT OF A LIGHT-WEIGHT REGENERATIVELY COOLED THRUST CHAMBER WITH BRAZED RIBS AND BRAZED OUTER WIRE TRAP

Design and fabrication procedures are discussed of a brazed-ribtype thrust chamber fabricated from stainless steel or inconel for a Sooo-lb thrust 20: 1 expansion-area-ratio regeneratively cooled liquidpropellant rocket engine which is designated as the JPL 6K Engine and operates at a chamber pressure of 150 psia. Hydrazine is used as the fuel and regenerative coolant and nitrogen tetroxide as the oxidizer. The nozzle-throat diameter is 5.42 in. The thrust chamber consists of a sheet-metal gas-side liner with longitudinal ribs spotwelded and brazed to the outer surface. Wire is wrapped over the ribs circumferentially, spot-welded to the ribs, and brazed. The liner, ribs, and wire form the coolant-passage walls. There are three basic advantages to this type of thrust chamber: light weight, ease of fabrication, and comparatively low cost. The total dry weight of a thrust chamber of this type and size made of 347 stainless steel is 46.2 lb, and the wet weight is 56.3 Ib. A total of 87 static engine tests were made on 19 of 23 thrust chambers fabricated by this technique. Four of the chambers tested had an expansion-area ratio of 20:1, and 15, which were shorter but had the same throat diameter, had an expansion-area ratio of 3.5:l. Accumulated test time was 1926 sec, including 558 sec regenerative cooling with hydrazine and 1368 sec cooling with water. One 20:l thrust chamber was subjected to 16 separate engine tests, with an accumulated test time of 399 sec, and was still in very good operating condition after the tests were completed. With water flowing through the coolant passages at 10 lb/sec, the measured nominal pressure drop between coolant manifolds of a 20:l thrust chamber wrapped with flat wire was 17.2 psi.

Thrust Chamber↗
NASA NTRS1968

Infrared spectroradiometer for rocket exhaust analysis

Infrared spectroradiometer measures high-resolution spectral absorption, emission, temperature, and concentration of chemical species in radically symmetric zones of the exhaust plumes of large rocket engines undergoing static firing tests. Measurements are made along predetermined lines of sight through the plume.

Herget, W. F.↗
NASA NTRS1971

Investigation of flaw geometry and loading effects on plane strain fracture in metallic structures

The effects on fracture and flaw growth of weld-induced residual stresses, combined bending and tension stresses, and stress fields adjacent to circular holes in 2219-T87 aluminum and 5AI-2.5Sn(ELI) titanium alloys were evaluated. Static fracture tests were conducted in liquid nitrogen; fatigue tests were performed in room air, liquid nitrogen, and liquid hydrogen. Evaluation of results was based on linear elastic fracture mechanics concepts and was directed to improving existing methods of estimating minimum fracture strength and fatigue lives for pressurized structure in spacecraft and booster systems. Effects of specimen design in plane-strain fracture toughness testing were investigated. Four different specimen types were tested in room air, liquid nitrogen and liquid hydrogen environments using the aluminum and titanium alloys. Interferometry and holograph were used to measure crack-opening displacements in surface-flawed plexiglass test specimens. Comparisons were made between stress intensities calculated using displacement measurements, and approximate analytical solutions.

Hall, L. R.↗
NASA NTRS1972

Space shuttle: Aerodynamic characteristics of the Titan T 3 (1207-4)/GAC H-33 launch configuration

Aerodynamic data obtained in a 14-inch trisonic wind tunnel test on static stability and drag of 0.003366-scale models of the Grumman H-33 drop tank orbiter and the Titan T 3 (1207-4) expendable booster are presented. The orbiter was mounted to the booster both piggyback and tandem. Data were obtained over a Mach number range of 0.6 to 5.0. Angle of attack data were obtained from -16 deg to +4 deg at both 0 deg and -6 deg sideslip for the piggyback configuration, but were limited to -10 deg to +10 deg at 0 deg sideslip for the tandem configuration. Primary configuration variations, other than piggyback and tandem mount, were the number and location of solid propellant strap-on boosters.

Sims, J. F.↗