Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid-state electrolytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Structural and Electrochemical Characterization of Thin Film Li 2 MoO 3 Electrodes

We report that Li 2 MoO 3 is a promising structural stabilizing unit for use in composite layered-layered cathodes for Li-ion batteries. To enable the rational design of such cathodes, studies on fundamental phenomena related to the active material structure and electrode/electrolyte interface are needed. The present work details the fabrication and characterization of thin film Li 2 MoO 3 cathodes and shows that their electrochemical performance greatly depends on the nature of the cathode/electrolyte interface. The Li 2 MoO 3 thin films exhibit poor cyclability in a liquid carbonate electrolyte (e.g., initial capacity of 166 mAh/g with 40% capacity fade over 20 cycles) whereas all-solid-state Li 2 MoO 3 /Lipon/Li batteries show negligible fade during cycling. A suite of characterization methods including Raman spectroscopy and X-ray photoelectron spectroscopy are used to study the evolution of the cathode structure and cathode electrolyte interphase (CEI) layer during charge/discharge cycling. Li transport rates are another important factor which affect cathode performance. AC impedance spectroscopy studies reveal that the Li diffusion coefficient (D Li ) in Li 2 MoO 3 decreases from 4.36 × 10 -11 cm 2 /s in the fully discharged state to 4.51 × 10 -13 cm 2 /s when charged to 3.6 V vs. Li/Li + . In conclusion, the results presented herein provide insight on the fundamental phenomena which govern Li 2 MoO 3 cathode performance.

25 ENERGY STORAGE↗
DOE OSTI2017

Freeze Tape Cast Thick Mo Doped Li 4 Ti 5 O 12 Electrodes for Lithium-Ion Batteries

Lithium titanate (Li 4 Ti 5 O 12 ) powders with and without molybdenum doping (LTO and MoLTO respectively) were synthesized by a solid-state method and used to fabricate electrodes on Cu foil using a normal tape-cast method and a novel freeze-tape-cast method. Modest molybdenum doping produces a significant electronic conductivity increase (e.g. 1 mS cm -1 for MoLTO vs 10 -7 mS cm -1 for LTO) that is thought to reflect a partial Ti 4+ reduction to Ti 3+ with charge compensation by the Mo 6+ dopant, producing a stable mixed-valent Ti 4+/3+ state. Freeze-tape-cast electrodes were fabricated by a variant of the normal tape-cast method that includes a rapid freezing step in which the solvent in the Cu-foil-supported slurry is rapidly frozen on a cold finger then subsequently sublimed to create unidirectional columnar macropores in the electrode. The resulting electrodes exhibit high porosity and low tortuosity which enhances electrolyte accessibility throughout the full electrode thickness. Freeze-tape-cast electrodes subjected to galvanostatic charge-discharge testing as cathodes in cells vs. a lithium metal anode exhibit higher specific capacity and lower capacity loss at high discharge rates compared with normal-tape-cast electrodes of the same mass loading, despite the fact that the freeze-tape-cast electrodes are nearly twice as thick as the normal tape cast electrodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Interface potentials inside solid-state batteries: Origins and implications

Interface resistance has become a significant bottleneck for solid-state batteries (SSBs). Most studies of interface resistance have focused on extrinsic mechanisms such as interface reactions and imperfect contact between electrodes and solid electrolytes. Interface potentials are an important intrinsic mechanism that is often ignored. Here, we highlight Kelvin probe force microscopy (KPFM) as a tool to image the local potential at interfaces inside SSBs, examining the existing literature and discussing challenges in interpretation. Drawing analogies with electron transport in metal/semiconductor interfaces, we showcase a formalism that predicts intrinsic ionic resistance based on the properties of the contacting phases, and we emphasize that future battery designs should start from material pairs with low intrinsic resistance. Here, we conclude by outlining future directions in the study of interface potentials through both theory and experiment.

25 ENERGY STORAGE↗
DOE OSTI2021

Resistance to fracture in the glassy solid electrolyte Lipon

We report on the mechanical behavior of a solid Li-ion conductor, lithium phosphorous oxynitride (Lipon), for solid-state batteries. In particular, the purpose of this investigation was to quantify the resistance to cracking (fracture toughness) of this material by nanoindentation. We observed surprising ductility and the ability to recover in Lipon. We were unsuccessful in inducing cracks in Lipon and observed accommodation of stress via pile-up and densification rather than by cracking at various strain rates. Simulations demonstrate that both deformation and densification depend on the alkali content. Densification appears to be recoverable at room temperature. We discuss the findings in comparison with nanoindentation-induced cracking in other inorganic solid electrolyte materials and provide possible explanations for high resistance of Lipon to Li filament propagation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

VTO FY20Q4 quarterly report

Project Objective.This project has three objectives: (1) tuning microstructures of 3D-printed SSE separators,(2) determining material and processing compatibilities with cathode printing,and (3)3D printing of sintering-free SSE separators.Project Impact.All-solid-state lithium batteries are difficult to process due to the brittleness of ceramic materials, poor solid-solid contact, and electrolyte-electrode stability issues. As a result, the energy and power density and also cycling stability are far from satisfying. This project will address fabrication difficulties by using state-of-the-art 3D-printing techniques that can introduce 3D interfaces and architectures to enhance solid-solid contact and reduce charge transfer resistance. Success will benefit the DOE by establishing the best manufacturing methods for ASSBsto achieve VTO goals on the performance of beyond Li-ion batteries. Approach.The project employs 3D-printing techniques to manufacture SSEs and related components for ASSBs. The team starts with direct ink writing (DIW) to develop ink recipes with desired rheological properties and explore post-sintering approaches to achieve high densification. In parallel with DIW3D printing, the team also explores other 3D printing options, such as projection microstereolithography (PuSL). Both sintering and sintering-free approaches can gain benefit from 3D printing and therefore will be investigated.Out-Year Goals.The team will determine particle sizes and morphologies as well as post-processing conditions that deliver good ionic conductivity and charge transfer properties of LLZTO separators. They will examine co-sintering of LLZTO/cathode and determine the effects of material, particle size, surface coating, and sintering conditions.Collaborations.Microstructures, ionic conductivities, and mechanical properties will be provided to the LLNL simulation team, led by PI B. Wood, for establishing and validating phase-field modeling methods.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid State Ionics: Materials Development by Multiscale Modeling and Advanced Manufacturing Techniques

Solid-state ionic materials are an important enabling technology for energy conversion and storage. Solid-state batteries would be a safer and higher energy density alternative to commercially available lithium ion batteries (LIB), however their implementation requires ion conduction in solids at room temperature to occur on the same level as the current generation of liquid electrolytes. Microstructural modifications have been demonstrated to play a major role on ion transport through the control of grain boundary interfaces, which traditionally serve as “blocking” layers. Ultimately, these materials will be fabricated in thin films form as electrolytes in order to minimize ohmic losses in electrochemical devices. This work uses advanced manufacturing techniques in combination with theoretical modeling to implement a science-based approach in the deposition of thin films ion conductors with controlled microstructures used in ceramic energy conversion and storage devices.

25 ENERGY STORAGE↗
DOE OSTI2023

Predictive Engineering of Interfaces and Cathodes for High-Performance All Solid-State Lithium-Sulfur Batteries

The primary goal of this project is to leverage data-driven methods and machine learning strategies to develop accurate multi-physics models for all-solid-state Li-S battery (ASLSB) materials that can capture electrochemical and transport phenomena over atomic to mesoscopic length/timescales. These models will be rigorously validated by synthesis and advanced characterization experiments. The team will leverage the predictive power of these models, alongside synthesis/characterization experiments and battery fabrication to address longstanding issues at the electrode/electrolyte interfaces in ASLSBs. The project’s proposed technology involves the following: (1) halide-doped solid sulfide electrolytes that can concurrently provide high Li + ion conductivity and suppress dendrite growth; (2) novel mesoporous cathode composed of super-P and carbon nanotubes co-infiltrated with sulfur and sulfide electrolyte, which hold potential to allow high sulfur loading and optimal ion/electron pathways; and (3) functionalization of sulfide electrolyte with ionic liquids to improve physical contact and minimize impedance at the cathode/electrolyte interface. Successful development of proposed predictive models (at multiple scales) will bridge this knowledge gap and will advance fundamental understanding of reaction chemistry, kinetics, charge transfer, and dendrite growth at electrified SSIs. This will enable predictive design of effective strategies to mitigate interfacial problems in ASSLSBs, including poor interfacial contact, interfacial impedance to Li + ion transport, and poor electron/ion conduction within cathodes. Ultimately, the fundamental knowledge gained will lead to development of high-performance ASSLSBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Development of 3D Printing Techniques for Solid-State Lithium Batteries: Energy Storage Internship (Final Report)

The goal of this internship was to develop a solid polymer electrolyte with a suitable ionic conductivity and mechanical properties and integrate it with 3D printed cathode for solid state lithium batteries. While liquid electrolytes will have much higher conductivities and therefore higher power densities than solid electrolytes, batteries with such electrolytes suffer from extreme dendritic growth, short-circuiting, and general failure. Typically, batteries prevent this by including a solid yet porous separator somewhere between the anode and cathode to suppress dendritic growth. Solid polymer electrolyte acts as the conductive medium between electrodes as well as the separator that prevents failure from short-circuiting. The specific system explored is a vinyl ethylene carbonate (VEC) and polyethylene glycol diacrylate (PEGDA) mixed polymer solution using both 2,2’-azobis(2-methylpropionitrile) (AIBN) and Irgacure 819, respectively as thermal and photo- initiators. Electrochemical and rheological techniques were used to determine the optimal polymer solution and curing conditions. Through this research, multiple new pathways of exploration have been determined to create a usable solid polymer electrolyte through a combination of varying cure intensities and initiator concentrations.

25 ENERGY STORAGE↗
DOE OSTI2024

Solid State Li Ion Batteries Using Si Composite Anodes

Solid Power has teamed with Argonne National Laboratory (ANL) to develop an all solid-state lithium-ion battery (ASSB), enabled by a high-capacity Si anode and a solid state electrolyte (SSE). Replacing liquid electrolytes with solid electrolytes addresses the calendar life challenges that currently limit the widespread adoption of Si anodes. In this project, Si-SSE composite materials have been developed with a specific capacity >1500 mAh/g (at electrode level). A Si anode was coated by using a roll-to-roll process. All-solid-state NMC-Si pouch cells have been assembled and tested. Cycle life of 1100 at 100% DOD has been demonstrated in the solid state Si pouch cell. Excellent calendar life is achieved in the cell via a high temperature storage test.

25 ENERGY STORAGE↗
DOE OSTI2020

Enhancing Superionic Conductivity in Cluster-Based Sodium-Rich Antiperovskites

Sodium (Na) superionic conductors are the key to developing next-generation solid-state batteries with safety and low cost. However, most of the known Na-conductors exhibit limited ionic conductivities at room temperature (RT), hindering their practical applications. To meet the challenge, a series of Li- and Na-rich antiperovskite superionic conductors based on cluster ions (e.g. BH4- and BCl4-) have been theoretically developed [e.g. Fang et al. PNAS 114, 11046, 2017; ACS App. Mat. Inter. 11, 963, 2018]. These materials exhibit superior properties as solid electrolytes with greatly enhanced ionic conductivities at RT. One cluster-based solid electrolyte of such, Na3O(BH)4, has been successfully synthesized for the first time most recently and its measured RT ionic conductivity is well above 10-3 S/cm which is four orders of magnitude higher than that of its halogen counterparts Na3OX (X = Cl, Br, I) [Sun et al. J. Am. Chem. Soc. 141, 5640, 2019]. In this work, we aim to further enhance the ionic conductivity of the Na-superionic conductor by using chemical mixing according to the size effect. The study further shows the advantage of utilizing cluster ions as building blocks, introducing additional degrees of freedom into tuning the properties of superionic conductors.

Fang, Hong↗
DOE OSTI2025

Novel Superionic Na Conductors for Solid‐State Na batteries: Materials and Interface

This project aims to advance the fundamental understanding on how the cation or anion doping influence on the crystal structure, phase stability and ion transport of novel Na superionic conductors. Specifically, we focus on the Na 3-x A x SbS 4-y X y family solid electrolytes (A: cation dopant, X: anion dopant), a class of promising materials for all-solid-state sodium batteries owing to their high ionic conductivity and compositional tunability. By integrating materials synthesis, neutron scattering, and electrochemical characterization and theoretical simulations, this project sees to elucidate 1) how does the synthesis approaches (solid-state reaction, low-temperature reaction) on the phase purity and doping process; 2) how chemical doping (A: cation dopants such as Sn; X: anion dopants such as Se, F) modulate lattice dynamics and Na+ migration as well as interface stability toward Na metal. Specifically, this project’s proposed technology involves three objectives: (1) synthesize novel Na-ion conductors (anion or cation doped Na 3 SbS 4 ) with high phase purity and examine their structural features (e.g., phase stability); (2) understand Na-ion conductive properties of new Na-ion conductors through a combination of experimental characterizations and theoretical simulations; (3) investigate the interface stability of novel Na superionic conductors with electrode materials in solid-state Na batteries. These objectives will be achieved through combined experimental synthesis/characterizations and computational approaches. The obtained knowledge will provide a comprehensive synthesis-structure-property correlation, enabling the rational design of novel solid-state conductors with excellent conductivity and stability.

25 ENERGY STORAGE↗
DOE OSTI2022

Task-Specific Phosphonium Iongels by Fast UV-Photopolymerization for Solid-State Sodium Metal Batteries

Sodium metal batteries are an emerging technology that shows promise in terms of materials availability with respect to lithium batteries. Solid electrolytes are needed to tackle the safety issues related to sodium metal. In this work, a simple method to prepare a mechanically robust and efficient soft solid electrolyte for sodium batteries is demonstrated. A task-specific iongel electrolyte was prepared by combining in a simple process the excellent performance of sodium metal electrodes of an ionic liquid electrolyte and the mechanical properties of polymers. The iongel was synthesized by fast (<1 min) UV photopolymerization of poly(ethylene glycol) diacrylate (PEGDA) in the presence of a saturated 42%mol solution of sodium bis(fluorosulfonyl)imide (NaFSI) in trimethyl iso-butyl phosphonium bis(fluorosulfonyl)imide (P111i4FSI). The resulting soft solid electrolytes showed high ionic conductivity at room temperature (≥10 -3 S cm -1 ) and tunable storage modulus (10 4 –10 7 Pa). Iongel with the best ionic conductivity and good mechanical properties (Iongel10) showed excellent battery performance: Na/iongel/NaFePO 4 full cells delivered a high specific capacity of 140 mAh g -1 at 0.1 C and 120 mAh g -1 at 1 C with good capacity retention after 30 cycles.

25 ENERGY STORAGE↗
NASA NTRS2006

Alpha-Voltaic Sources Using Liquid Ga as Conversion Medium

A family of proposed miniature sources of power would exploit the direct conversion of the kinetic energy of alpha particles into electricity. In addition to having long operational lives, these sources are expected to operate with energy-conversion efficiencies from 70 to 90 percent. A power source as proposed (see figure) would be an electrolytic cell in which liquid gallium would serve as both an electrolyte and an energy-conversion medium. The cell would contain an iridium cathode and a zirconium anode. The alpha particles, each with a kinetic energy approx.5.8 MeV, would be emitted by radioactive decay of Cm-244, which has a half-life of 18 years. The Cm-244 source would be positioned so that the a particles would enter the liquid gallium, where their kinetic energy would be dissipated mostly through ionization of Ga atoms, creating Ga(+) ions and free electrons. The electrons would be collected by iridium cathode, and the Ga(+) ions would be neutralized at the zirconium cathode by electrons returning after flowing through an external circuit. Gallium is a candidate for use as the electrolyte and the energy-conversion medium because in the liquid state it is a semimetal: its electrical conductivity is greater than that of a typical semiconductor but small in comparison with the conductivities of metals. Consequently, in liquid gallium, electrons and Ga(+) can exist without immediate recombination and can be moved by electric fields. It is expected that electric fields, resulting at least partly from the difference between the work functions of the electrode metals, would move the electrons and ions to their respective electrodes. The open-circuit potential of the cell is expected to be 1.62 V - equal to the difference between the work functions of iridium and zirconium. Unlike in a solid-state energy conversion medium, the impingement of energetic a particles would not give rise to displacement damage in the liquid gallium. Hence, the cell should have a long life, limited only by the half-life of Cm-244. A cell having a volume less than 25 cu mm, containing 1 curie of Cm-244 (the curie is a unit of radioactivity equal to 3.7 10(exp 10) disintegrations per second) is expected to deliver a current between 7 and 12 mA, which, at the expected open-circuit potential, would provide a power in the approximate range of 11 to 20 mW.

Patel, Jagdish U.↗
DOE OSTI2018

Solid-state three-dimensional battery assembly

A solid-state three-dimensional battery assembly includes a solid bicontinuous monolithic carbon anode, a solid electrolyte layer, and a solid cathode. The solid monolithic carbon anode has an ordered three-dimensionally continuous network nanostructure, a length of at least 100 nm, and an average thickness of 3 to 90 nm. The ordered three-dimensionally continuous network nanostructure of the anode defines a plurality of pores having an average diameter of 5 to 100 nm. The solid electrolyte layer is disposed directly on the anode, has an average thickness of 3 to 90 nm, and fills a portion of the pores defined by the ordered three-dimensionally continuous network nanostructure of the anode. The solid cathode is disposed directly on the electrolyte layer, has an average thickness of 3 to 90 nm, and also fills a portion of the pores defined by the ordered three-dimensionally continuous network nanostructure of the anode. Related devices and methods are also provided.

25 ENERGY STORAGE↗
DOE OSTI2024

Nasicon dual ion conductors for all solid-state batteries

A super ion conductor composition is disclosed. The super ion conductor composition has the general formula: A 1+x M x/2 Zr 2−x/2 (PO 4 ) 3 , where each A is independently Na or Li, M is Mn or Mg, and subscript x is from 0.5 to 3. A solid electrolyte comprising the super ion conductor composition, and a method of preparing the solid electrolyte, are also disclosed. The method comprises combining a zirconium compound, a manganese or magnesium compound, a sodium compound, and a phosphate compound to give a mixture; and calcining the mixture to give the super ion conductor composition, thereby preparing the solid electrolyte. Functional materials and devices comprising the super ion conductor composition are also disclosed, including a catholyte composition, an ion conducting solid electrolyte membrane, as well as all-solid-state batteries.

Amin, Ruhul↗