SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Brief report describes concept for coal-burning hybrid rocket engine. Proposed engine carries larger payload, burns more cleanly, and safer to manufacture and handle than conventional solid-propellant rockets. Thrust changeable in flight, and stops and starts on demand.
The objective was to investigate, through experimental means, the basic mechanisms influencing ignition overpressure and to determine ways to suppress ignition overpressure. Ignition overpressure was studied using solid rocket motors with geometry scaled at 1 percent of the Shuttle's Solid Rocket Boosters. Both water injection and aerosol foam were examined as a mean of reducing ignition overpressure. The results of the water injection tests indicate that a relatively small amount of water is sufficient to provide significant suppression. Of the flow rates tested, the lower water injection flow rates provided the best reduction of the ignition overpressure wave. Also, the test results show there is an optimum water flow rate range that provides the best suppression, and as this range is exceeded the effectiveness of water to reduce ignition overpressure is decreased. Aerosol foam provided very little reduction of ignition overpressure, but only small volumes of foam were used and further testing is necessary to determine its total effectiveness as a means of suppression.
This paper addresses the unique problems associated with launching the Black Brant V, VIII, and IX sounding rocket vehicles at White Sands Missile Range (WSMR) and the significance of the introduction of the S19 to the NASA Goddard Space Flight Center Wallops Flight Facility sounding rocket program in terms of launch flexibility, improved impact dispersion, higher flight reliability, and reduced program costs. This paper also discusses salient flight results from NASA 36.011UL (the first S19 guided Black Brant launched at WSMR) and the NASA Comet Halley missions (36.010DL and 36.017DL).
For several years, the TAD2 computer program has been used to calculate the aerodynamic properties of sounding rockets. This program was limited, however, in that a maximum of two fin sets could be accommodated analytically. In addition, the roll moment coefficients did not consider downwash effects. Techniques are developed and equations derived for the expansion of capability to include three fin sets. The effects of downwash on the roll moment coefficients are also treated analytically for two and three stage rockets.
A reclosable clamshell noise fairing system was developed and successfully flown on a Black Brant VC sounding rocket. The clamshell system involved the design of unique structural and mechanical subsystems to meet the experimenters requirements, withstand environmental conditions of sounding rocket flight and recovery, and be relatively easy to maintain with a clean interface between the experiment detectors and instrumentation section of the payload. The development of the equations of motion of the mechanism are illustrated and results of the test of the Engineering Test Model (ETM) are shown.
The design, development, and testing of the Flip-Flop Recovery System, which protects sensitive forward-mounted instruments from ground impact during sounding rocket payload recovery operations, are discussed. The system was originally developed to reduce the impact damage to the expensive gold-plated forward-mounted spectrometers in two existing Taurus-Orion rocket payloads. The concept of the recovery system is simple: the payload is flipped over end-for-end at a predetermined time just after parachute deployment, thus minimizing the risk of damage to the sensitive forward portion of the payload from ground impact.
The potential for advanced rocket-powered launch vehicles to meet the challenging cost, operational, and performance demands of space transportation in the early 21st century is examined. Space transportation requirements from recent studies underscoring the need for growth in capacity in support of an increasing diversity of space activities and the need for significant reductions in operational and life-cycle costs are reviewed. Fully reusable rocket powered concepts based on moderate levels of evolutionary advanced technology are described. These vehicles provide a broad range of attractive concept alternatives with the potential to meet demanding operational and cost goals and the flexibility to satisfy a variety of vehicle architecture, mission, vehicle concept, and technology options.
A concept for a heat-pipe-cooled rocket engine, which involves the use of heat pipes to augment radiation cooling on small, low-flux rocket engines used for attitude control and stationkeeping on satellites, is discussed. Results of the thermal and performance analyses performed on a prototype heat cooled thrust chamber are presented, together with the results of fabrication experiments. A test plan for full-scale hot fire hardware testing is outlined.
Results are reported from the ECHO-6 electron-beam-injection experiment, performed in the auroral-zone ionosphere on March 30, 1983 using a sounding rocket equipped with two electron guns and a free-flying plasma-diagnostics instrument package. The data are presented in extensive graphs and diagrams and characterized in detail. Large ELF wave variations, superposed on the strong beam-sector-directed quasi-dc component, are observed in the 100-eV beam-induced plasma when the beam is injected in a transverse spiral, but not when it is injected upward parallel to the magnetic-field line. ELF activity is found to be suppressed whenever the rocket passed through field lines with auroral activity, suggesting that the waves are produced by the interaction of the beam potentials, plasma currents, and return currents neutralizing the accelerator payload.
The heat exchanger concept is discussed together with its role in rocket engine operation in idle modes. Two heat exchanger designs (low and high heat transfer) utilizing different approaches to achieve stable oxygen vaporization are presented as well as their performance test results. It is concluded that compact and lightweight heat exchangers can be used in a stable manner under the 'idle' operating conditions expected with the RL10 rocket engine.
Life tests were conducted on a 22-N (5-lb) hydrazine rocket thruster which incorporates the latest technology to obtain long life from the catalyst bed. A spring mechanism surrounding the catalyst bed continually applies compression to the catalyst bed to prevent the formation of any void channels. The research rocket thruster was tested over an operational cycle of both steady state and pulse firing which simulated a possible space station duty cycle. The thruster ran as expected for about 40 hours, or 3.2 times 10 to the 6th power N-sec (7.2 times 10 to the 5th power lb-sec) total impulse. Subsequently, some thrust chamber pressure decreases were noted during long steady state test periods. After 60.2 hours of run time, tests had to be terminated due to a blockage in the propellant injector tube which occurred during heating of the thruster by a heat lamp. A chemical analysis of the catalyst indicated that iron and nickel metals had poisoned some of the catalyst, thereby causing a degradation in performance. It was determined that a contaminated barrel of hydrazine was the source of the metal poisoning.
The super Cold Arctic Mesopause Project (CAMP) follow-up project in the summer of 1990 is outlined. In situ measurements of appropriate height resolution are needed in the summer mesosphere at high latitudes to investigate structures and formation processes of polar mesospheric clouds. The rocket measurements from the high latitude site Thule AB in Greenland (76.6 N) are decisive for the understanding of the cold Arctic mesopause. Similar rocket measurements from the European ranges Andenes and Esrange (68 to 69 N) are needed to investigate the latitudinal variability of the parameters relevant for the formation, transport, and loss of mesospheric ice particles. An important aspect of Super CAMP is the study of the heterogeneous chemistry, the loss of electrons on aggregates, and the build-up of horizontal and vertical electric fields in the presence of charged ice particles. Instruments, measurements, and purpose are listed.
Previous to this report, the computer program of NASA SP-273 and NASA TM-86885 was capable of calculating theoretical rocket performance based only on the assumption of an infinite area combustion chamber (IAC). An option was added to this program which now also permits the calculation of rocket performance based on the assumption of a finite area combustion chamber (FAC). In the FAC model, the combustion process in the cylindrical chamber is assumed to be adiabatic, but nonisentropic. This results in a stagnation pressure drop from the injector face to the end of the chamber and a lower calculated performance for the FAC model than the IAC model.
A two-dimensional shell model of an entire solid rocket booster (SRB) has been developed using the STAGSC-1 computer code and executed on the Ames CRAY computer. The purpose of these analyses is to calculate the overall deflection and stress distributions for the SRB when subjected to mechanical loads corresponding to critical times during the launch sequence. The mechanical loading conditions for the full SRB arise from the external tank (ET) attachment points, the solid rocket motor (SRM) pressure load, and the SRB hold down posts. The ET strut loads vary with time after the Space Shuttle main engine (SSME) ignition. The SRM internal pressure varies axially by approximately 100 psi. Static analyses of the full SRB are performed using a snapshot picture of the loads. The field and factory joints are modeled by using equivalent stiffness joints instead of detailed models of the joint. As such, local joint behavior cannot be obtained from this global model.
An intelligent control system for reusable space propulsion systems for future launch vehicles is described. The system description includes a framework for the design. The framework consists of an execution level with high-speed control and diagnostics, and a coordination level which marries expert system concepts with traditional control. A comparison is made between air breathing and rocket engine control concepts to assess the relative levels of development and to determine the applicability of air breathing control concepts to future reusable rocket engine systems.
This paper reports the results of three tethered rocket experiments conducted as part of a U.S.-Japan joint program under way since 1980. The major purpose of the experiments is to obtain technical and scientific data supporting the figure electrodynamic tethered subsatellite experiments by the Space Shuttle. Vehicle charging due to dc beam emission up to 80 mA in the 150-200 km altitude range was repeatedly measured by both Langmuir and floating probes, and was found to be usually less than 10 V. During the 80 mA emission, clear evidence for the ignition of a beam-plasma discharge was obtained. In a tether deployment experiment, it was found that the tether wire acted as an antenna whose impedance decreased with the extension of the wire both in high-frequency and very low-frequency bands. Substantial rocket charging was observed during periods of electron-beam very low-frequency pulsing.
In this paper, Solar Backscatter Ultraviolet (SBUV) measurements of solar irradiance and predictions from the Mg 280-nm index are compared with each other and with coincident Solar Mesosphere Explorer (SME) and rocket measurements. The SBUV irradiances show a systematic decrease with time not seen in the rocket measurements; a correction for this decrease is introduced. The scatter and overall structure in the SME spectra is 3-5 percent, of the order of or larger than most of the changes predicted by the Mg index. The corrected SBUV ratio and the Mg index prediction for it agree to within 1 percent. Such agreement supports a common origin for variations between solar maximum and minimum and those for individual rotations: the degree to which active regions cover the visible hemisphere of the sun.
Flow analyses have been performed to determine the nature of the three-dimensional flow field in the vicinity of the aft-most field joint of the Space Shuttle Redesigned Solid Rocket Motor (RSRM). Specific objectives included the quantification of the circumferential pressure and velocity gradients at the joint location which might be caused by the non-uniform erosion of the rubber inhibitor which protrudes from the wall into the flow field. Three-dimensional Navier-Stokes equations have been solved in conjunction with the conservation equation for the turbulence energy and the dissipation rate. The numerical predictions have been compared with the measurements from a 7.5 percent scale cold flow model of the redesigned solid rocket motor.