Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “resistive heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

The Material Response of PICA-NuSil to a Hypersonic Flow Environment

Phenolic Impregnated Carbon Ablator (PICA) is NASA’s baseline thermal protection system for missions to Mars. PICA is friable; therefore, NuSil ® CV-1144-0 is applied to the surface of flight hardware to mitigate the contamination of spacecraft sensors. NuSil is composed of a polysiloxane resin system that can transform into an oxidation-resistant coating upon heating. Therefore, a pathfinder campaign was conducted at the Hypersonic Materials Environmental Test System (HyMETS) at the NASA Langley Research Center to investigate the material response of instrumented sphere-cone models made from PICA coated with NuSil ® . Analysis of the post-test data is presented and suggests that NuSil ® impacts the material response of test articles subjected to oxidizing atmospheres, as evidenced by a reduction of the measured surface temperature and in-depth temperature response. Finally, a four-step ablation mechanism is proposed based on observations from high-speed video, optical emission spectroscopy, thermal analysis, and post-test surface characterization.

PICA PICA-NuSil Siloxane Silicone↗
DOE OSTI2021

THERMAL ANALYSIS OF THE RHIC ARC DIPOLE MAGNET COLD MASS WITH THE EIC BEAM SCREEN

The EIC will make use of the existing RHIC storage rings with their superconducting (SC) magnet arcs. A stain-less-steel beam screen with co-laminated copper and a thin amorphous carbon (aC) film on the inner surface will be installed in the beam pipe of the SC magnets. The copper will reduce the beam-induced resistive-wall (RW) heating from operation with the higher intensity EIC beams, that if not addressed would make the magnets quench. Limiting the RW heating is also important to achieve an adequately low vacuum level. The aC coating will reduce secondary electron yield which could also cause heating and limit in-tensity. Among all the RHIC SC magnets, the arc dipoles present the biggest challenge to the design and installation of beam screens. The arc dipoles, which make up for 78% (2.5 km) length of all SC magnets in RHIC, expect the larg-est RW heating due to their smallest aperture. These mag-nets are also the longest (9.45 m each), thus experiencing the largest temperature rise over their length, and have a large sagitta (48.5 mm) that increases the difficulty to in-stall the beam screen in place. This paper presents a de-tailed thermal analysis of the magnet-screen system.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Influence of Joule Heating on the Stability of High Temperature Irradiation Resistant Thermocouples

Development of in-core instrumentation is driven by the pursuit of safer and more economic energy production from both existing nuclear reactors and Generation IV reactor designs. Idaho National Laboratory (INL) has developed high temperature irradiation resistant thermocouples (HTIR-TCs) for temperature sensing inside Generation IV nuclear reactors. These thermocouples are composed of phosphorus-doped niobium (Nb-P) and lanthana-doped molybdenum (Mo-LaO) thermoelements, an alumina (Al2O3) insulation, and a niobium sheath. HTIR-TCs require an initial heat treatment exceeding the maximum service temperature to stabilize the generated electromotive force (EMF) signal; however, the mechanism behind this stabilization is not well understood. This work evaluates the impact of Joule heating on the thermoelements' microstructures, chemical stability, and mechanical properties to determine the mechanisms by which the EMF signal stabilization occurs. Accordingly, during the Joule heat treatment, a secondary Nb3P phase coarsened along the length of the Nb-P thermoelement, along with the formation of an interaction region at the Al2O3/niobium interface. The interaction between the alumina insulation and the Nb-P thermoelement was also observed within the Mo-LaO thermoelement. Joule heating induced stability within the generated EMF signal of HTIR-TCs through the formation of secondary phases within the Nb-P and the interaction of the alumina insulation with the thermoelements.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2022

Review of Thermal Contact Resistance of Flexible Graphite Materials for Thermal Interfaces in High Heat Flux Applications

In this report the data is reviewed on thermal contact conductance (TCC) and/or thermal contact resistance (TCR) at material interfaces which employs flexible graphite (FG) materials as thermal interface materials (TIM). FG materials are often used as TIM due to their conforming nature. While the overall TCR can be estimated straightforward from measured data, the interface TCR is much more difficult to obtain. The report also discusses the interfacial thermal contact conductance between FG-tungsten and FG-Glidcop-Al15, which are envisioned for high-heat flux applications.

36 MATERIALS SCIENCE↗
NASA NTRS2006

Dielectric Heaters for Testing Spacecraft Nuclear Reactors

A document proposes the development of radio-frequency-(RF)-driven dielectric heaters for non-nuclear thermal testing of the cores of nuclear-fission reactors for spacecraft. Like the electrical-resistance heaters used heretofore for such testing, the dielectric heaters would be inserted in the reactors in place of nuclear fuel rods. A typical heater according to the proposal would consist of a rod of lossy dielectric material sized and shaped like a fuel rod and containing an electrically conductive rod along its center line. Exploiting the dielectric loss mechanism that is usually considered a nuisance in other applications, an RF signal, typically at a frequency .50 MHz and an amplitude between 2 and 5 kV, would be applied to the central conductor to heat the dielectric material. The main advantage of the proposal is that the wiring needed for the RF dielectric heating would be simpler and easier to fabricate than is the wiring needed for resistance heating. In some applications, it might be possible to eliminate all heater wiring and, instead, beam the RF heating power into the dielectric rods from external antennas.

Sims, William Herbert↗
DOE OSTI2020

Comparison of Thermal Management Approaches for Integrated Traction Drives in Electric Vehicles

The continuous push to increase power densities of electric vehicle (EV) traction drive systems necessitates combining electric motor and power electronics into one unit. A single, compact traction drive unit with fewer interconnecting components also facilitates fast, automated assembly of electric vehicles, driving production costs down and enabling wider adoption of EVs. There are a number of challenges associated with the integration of power electronics with the electric machine, including thermal management of the combined traction drive system. However, one important benefit of integration from the thermal management system perspective is the potential for using a single fluid loop instead of two separate cooling systems for the electric machine and the power electronics/inverter. This paper reviews several integration approaches and, employing finite element analysis (FEA), compares thermal management solutions for the combined electric machine and power electronics systems. Namely, three different scenarios are modeled: (1) independent component (motor and power electronics) cooling, which is compared to the combined cooling system approach for (2) radially and (3) axially integrated power electronics modules into the motor enclosure. Temperature distributions for selected thermal loads and thermal resistances from the key heat-generating components to the cooling fluid are compared for each scenario.

47 OTHER INSTRUMENTATION↗
NASA NTRS1990

Isomeric Trisaryloxycyclotriphosphazene Polymer Precursors

Substances useful for making heat-and fire-resistant polymers. Cyclotriphosphazene-based monomers and polymer precursors led to development of high-temperature materials. Cyclotriphosphazene-derived monomers, polymer precursors, and polymers becoming important from both industrial and scientific points of view. Presence of phosphazene moiety in cyclotriphosphazene-based monomers and polymer precursors expected to impact special properties in desired high-performance materials containing inorganic backbones for aerospace applications. Useful for obtaining heat-and fire-resistant polymers for composites, adhesives, molding powders, and coating laminates. Also used in structures (e.g. secondary structures in aircraft), in construction of spacecraft, and in electronics and computer industries.

St. Clair, Terry L.↗
NASA NTRS1994

Measurement of a surface heat flux and temperature

The Heat Flux Microsensor is a new sensor which was recently patented by Virginia Tech and is just starting to be marketed by Vatell Corp. The sensor is made using the thin-film microfabrication techniques directly on the material that is to be measured. It consists of several thin-film layers forming a differential thermopile across a thermal resistance layer. The measured heat flux q is proportional to the temperature difference across the resistance layer q= k(sub g)/delta(sub g) x (t(sub 1) - T(sub 2)), where k(sub g) is the thermal conductivity and delta (sub g) is the thickness of the thermal resistance layer. Because the gages are sputter coated directly onto the surface, their total thickness is less than 2 micrometers, which is two orders of magnitude thinner than previous gages. The resulting temperature difference across the thermal resistance layer (delta is less than 1 micrometer) is very small even at high heat fluxes. To generate a measurable signal many thermocouple pairs are put in series to form a differential thermopile. The combination of series thermocouple junctions and thin-film design creates a gage with very attractive characteristics. It is not only physically non-intrusive to the flow, but also causes minimal disruption of the surface temperature. Because it is so thin, the response time is less than 20 microsec. Consequently, the frequency response is flat from 0 to over 50 kHz. Moreover, the signal of the Heat Flux Microsensor is directly proportional to the heat flux. Therefore, it can easily be used in both steady and transient flows, and it measures both the steady and unsteady components of the surface heat flux. A version of the Heat Flux Microsensor has been developed to meet the harsh demands of combustion environments. These gages use platinum and platinum-10 percent rhodium as the thermoelectric materials. The thermal resistance layer is silicon monoxide and a protective coating of Al2O3 is deposited on top of the sensor. The superimposed thin-film pattern of all six layers is presented. The large pads are for connection with pins used to bring the signal out the back of the ceramic. In addition to the heat flux measurement, the surface temperature is measured with a platinum resistance layer (RTS). The resistance of this layer increases with increasing temperature. Therefore, these gages simultaneously measure the surface temperature and heat flux. The demonstrated applications include rocket nozzles, SCRAM jet engines, gas turbine engines, boiling heat transfer, flame experiments, basic fluid heat transfer, hypersonic flight, and shock tube testing. The laboratory involves using one of these sensors in a small combustion flame. The sensor is made on a 2.5 cm diameter piece of aluminum nitride ceramic.

Davis, R. M.↗
NASA NTRS1987

Fatigue-resistant nickel-base superalloys

New γ' strengthened nickel-base superalloy compositions are described that, when forged and properly heat treated, demonstrate superior resistance to fatigue crack growth accompanied by very good high temperature properties. Parts can be fabricated (e.g., using conventional cast and wrought processing) from these alloys without encountering difficulty in forging.

Keh-Minn Chang↗
DOE OSTI2022

Convective Heat Transfer Potential of Particles/Airflow Through Single Cell Thick Additively Manufactured Octet-Shaped Lattice Frame Material

Abstract Particle-to-Supercritical Carbon Dioxide (sCO2) heat exchangers are one of the most critical components of the next-generation Concentrating Solar Power (CSP) plants. There have been several efforts to enhance the overall heat exchanger performance which essentially comprises of thermal resistances offered by sCO2 channel, wall (separating sCO2 with particles) thickness, particle-wall contact resistance and particle-side effective heat transfer coefficient. This study is focused towards reducing the particle side thermal resistance by incorporating single unit cell thick reticulated Octet lattice frame structures on the falling particle side to enhance the effective thermal conductivity of the particle channel and to enhance convective heat transfer between the falling particles and the solid phase of the falling particle channel (endwalls and fibers). Steady-state experiments were conducted to measure the effective thermal conductivity of lattice frame material for two cases: a) when void space was occupied by air, b) when void space was occupied with particles. Further, convective heat transfer experiments have been conducted with both air (steady-state) and particles (quasi steady-state) as “working fluid” for panels sandwiching the Octet array. Three different lattice porosities ranging from 0.75 to 0.9 have been tested for a wide range of air flow rates and a fixed particle flow rate (highest potential).

Aider, Youssef↗
NASA NTRS2012

Electrochemical Ultracapacitors Using Graphitic Nanostacks

Electrochemical ultracapacitors (ECs) have been developed using graphitic nanostacks as the electrode material. The advantages of this technology will be the reduction of device size due to superior power densities and relative powers compared to traditional activated carbon electrodes. External testing showed that these materials display reduced discharge response times compared to state-of-the-art materials. Such applications are advantageous for pulsed power applications such as burst communications (satellites, cell phones), electromechanical actuators, and battery load leveling in electric vehicles. These carbon nanostructures are highly conductive and offer an ordered mesopore network. These attributes will provide more complete electrolyte wetting, and faster release of stored charge compared to activated carbon. Electrochemical capacitor (EC) electrode materials were developed using commercially available nanomaterials and modifying them to exploit their energy storage properties. These materials would be an improvement over current ECs that employ activated carbon as the electrode material. Commercially available graphite nanofibers (GNFs) are used as precursor materials for the synthesis of graphitic nanostacks (GNSs). These materials offer much greater surface area than graphite flakes. Additionally, these materials offer a superior electrical conductivity and a greater average pore size compared to activated carbon electrodes. The state of the art in EC development uses activated carbon (AC) as the electrode material. AC has a high surface area, but its small average pore size inhibits electrolyte ingress/egress. Additionally, AC has a higher resistivity, which generates parasitic heating in high-power applications. This work focuses on fabricating EC from carbon that has a very different structure by increasing the surface area of the GNF by intercalation or exfoliation of the graphitic basal planes. Additionally, various functionalities to the GNS surface will be added that can exhibit pseudocapacitance. This pseudocapacitance exhibits faradaic (charge transfer) properties that can further increase the overall relative and volumetric capacitance of the material. A process is also proposed to use GNF as a precursor material to fabricate GNS that will be used as EC electrodes. This results in much better electrical conductivity than activated carbon. This is advantageous for high-pulsed-power applications to reduce parasitic heating. Larger average pore size allows more complete electrolyte wetting (faster charge transfer kinetics). These properties contribute to a lowered equivalent series resistance (ESR), increased specific power, shorter charging times, and decreased parasitic heating. The high density of basal plane edges provides nucleation sites for activation (addition of hydrophilic functional groups) that facilitate electrolyte wetting, and will contribute to pseudocapacitance.

Marotta, Christopher↗
NASA NTRS1988

Stronger Fire-Resistant Epoxies

New curing agent improves mechanical properties and works at lower temperature. Use of aminophenoxycyclotriphosphazene curing agents yields stronger, more heat- and fire-resistant epoxy resins. Used with solvent if necessary for coating fabrics or casting films.

Fohlen, George M.↗
NASA NTRS1974

Major uncertainties influencing entry probe heat shield design

Factors influencing the design of an outer planet probe heat shield are discussed. Major factors included are: uncertainties in composition and scale height of the planet atmospheres; the augmentation/attenuation of entry heating by ablation products requires more computer study and testing; carbon heat shields, especially carbon phenolic, possessing improved resistance to spallation need developing; and white silica reflecting heat shields with improved resistance to bulk vitrification need further developing.

Congdon, W.↗
DOE OSTI2020

Pressure tuning of structural and magnetic transitions in EuAg 4 As 2

We report temperature-dependent measurements of ambient-pressure specific heat, magnetic susceptibility, anisotropic resistivity, and thermal expansion as well as in-plane resistivity under pressure up to 20.8 kbar on single crystals of EuAg 4 As 2 . Based on thermal expansion and in-plane electrical transport measurements at ambient pressure this compound has two, first-order, structural transitions in the 80–120 K temperature range. Ambient-pressure specific heat, magnetization, and thermal expansion measurements show a cascade of up to seven transitions between 8 and 16 K associated with the ordering of the $Eu^{2+}$ moments. In-plane electrical transport is able to detect the more prominent of these transitions, at 15.5, 9.9, and 8.7 K, as well as a weak feature at 11.8 K at ambient pressure. Pressure-dependent electrical transport data show that the magnetic transitions shift to higher temperatures under pressure, as does the upper structural transition, whereas the lower structural transition is suppressed and ultimately vanishes. A jump in resistivity, associated with the upper structural transition, decreases under pressure with an extrapolated disappearance (or a change of sign) by 30–35 kbar. In the 10–15 kbar range a kink in the pressure dependency of the upper structural transition temperature as well as the high- and low-temperature in-plane resistivities suggests that a change in the electronic structure may occur in this pressure range. The results are compared with the literature data for EuAg 4 As 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Additive Manufacturing of Corrosion Resistant UHTC Materials for Chloride Salt-to-sCO2 Brayton Cycle Heat Exchangers

The objectives of the project include: (1) screen high-purity, high density ultra-high-temperature ceramics (UHTCs) for chloride salt corrosion resistance, (2) develop binder-jet additive manufacturing and sintering for ZrB 2 -MoSi 2 blends using literature and experiments to demonstrate feasibility, and (3) evaluate chloride salt corrosion resistance of additively manufactured ZrB 2 -MoSi 2 . These initial objectives support the development of a durable and reliable ultra-compact high-efficiency salt-to-sCO 2 heat exchanger for closed-loop Brayton power cycles based on corrosion resistant, high-strength, thermally conductive UHTC materials and novel designs enabled by additive manufacturing. The UHTC materials are also abrasion resistant so that they could be applicable to all three thermal carrier media pathways identified in the CSP Gen3 Roadmap.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing

Additively-manufactured Ti-6Al-4V (Ti64) exhibits high strength but in some cases inferior elongation to those of conventionally manufactured materials. Post-processing of additively manufactured Ti64 components is investigated to modify the mechanical properties for specific applications while still utilizing the benefits of the additive manufacturing process. The mechanical properties and fatigue resistance of Ti64 samples made by electron beam melting were tested in the as-built state. Several heat treatments (up to 1000 °C) were performed to study their effect on the microstructure and mechanical properties. Phase content during heating was tested with high reliability by neutron diffraction at Los Alamos National Laboratory. Two different hot isostatic pressings (HIP) cycles were tested, one at low temperature (780 °C), the other is at the standard temperature (920 °C). The results show that lowering the HIP holding temperature retains the fine microstructure (~1% β phase) and the 0.2% proof stress of the as-built samples (1038 MPa), but gives rise to higher elongation (~14%) and better fatigue life. The material subjected to a higher HIP temperature had a coarser microstructure, more residual β phase (~2% difference), displayed slightly lower Vickers hardness (~15 HV10N), 0.2% proof stress (~60 MPa) and ultimate stresses (~40 MPa) than the material HIP’ed at 780 °C, but had superior elongation (~6%) and fatigue resistance. Heat treatment at 1000 °C entirely altered the microstructure (~7% β phase), yield elongation of 13.7% but decrease the 0.2% proof-stress to 927 MPa. The results of the HIP at 780 °C imply it would be beneficial to lower the standard ASTM HIP temperature for Ti6Al4V additively manufactured by electron beam melting.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Methane pyrolysis by Joule heating for graphitic carbon and hydrogen production

The global energy transition toward sustainability requires technologies that can decarbonize energy carriers and fuels while producing valuable materials. Methane, a primary component of natural gas, is both a high-energy-density fuel and a significant greenhouse gas. This study reports an approach for methane pyrolysis utilizing Joule heating within the deposition substrate to drive the endothermic reaction. With electric current passing through a resistive porous carbon cloth, heat is generated to break C-H bonds of methane molecules. Here, the decomposition of methane as it flows through the cloth results in hydrogen production and the formation of conformally layered graphite around the carbon fibers. The effects of input power, chamber pressure, feedstock flow rate, and process duration on hydrogen and graphite production are characterized via in situ mass spectrometry and laser absorption spectroscopy, resulting in methane conversion rates up to 88%, with hydrogen and carbon yields of 82% and 72%, respectively. Material characterization verifies uniform high-quality graphite deposition, with a Raman I D /I G ratio of 0.1 and 3.38 Å d-spacing. This Joule heating method for catalyst-free methane pyrolysis offers the potential for advancing hydrogen production technology by simultaneously producing valuable materials such as solid graphite, thus enhancing the economic viability of the fuel decarbonization process.

Energy Resources↗
NASA NTRS1978

Electroexplosive device

An electroexplosive device is presented which employs a header having contact pins hermetically sealed with glass passing through from a connector end of the header to a cavity filled with a shunt layer of a new nonlinear resistive composition and a heat-sink layer of a new dielectric composition having good thermal conductivity and capacity. The nonlinear resistive layer and the heat-sink layer are prepared from materials by mixing with a low temperature polymerizing resin. The resin is dissolved in a suitable solvent and later evaporated. The resultant solid composite is ground into a powder, press formed into the header and cured (polymerized) at about 250 to 300 F.

Menichelli, V. J.↗