Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “regenerating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Water and Ammonia Desorption from 5A Zeolite

Demonstrate adsorption and desorption characteristics of water and ammonia on 5A zeolite during regeneration conditions using a Thermogravimetric analyzer (TGA) on samples previously evaluated by residual gas analyzer (RGA)/mass balance. Molecular sieve (zeolite) adsorbents have the following characteristics: Crystalline alumino-silicates containing pores or 'cages' that adsorb water or other molecules. Polar compound are adsorbed with high loading even at very low concentrations of the fluid. A 5A molecular sieve was chosen for its ability to adsorb both water and ammonia (NH{sub 3}) from a carrier gas stream. Preliminary RGA/mass balance testing indicated: 5A zeolite captured both NH{sub 3} and water as anticipated based on molecular size; Reloading showed limited success after zeolite heated beyond manufacturer recommended operating conditions: Steam dealumination theorized cause; Tests were reprioritized to focus on NH{sub 3} removal and end of life potential holdup of NH{sub 3} and water on 5A zeolite material. TGA measures a sample's weight and volatile composition as it is heated or cooled in a furnace. TGA heats sample to release volatile materials, (change in mass is measured). MS detects/measures low levels of impurities. Perform TGA desorption of zeolite samples taken at the following conditions tested with RGA (RGA results not shown here): Initial Bakeout conditions: hydrogen carrier gas, slowly raise temp to approximately 300 deg. C until desired moisture content <<100 ppm is achieved. Water loading (re-loading): argon carrier gas through bubbler until breach is observed. Ammonia loading (re-loading): hydrogen carrier gas through system. Regenerations/End of life conditions: hydrogen carrier gas, raise temp to approximately 300 deg. C, then slowly to 450 deg. C (end of life). After end of life testing less than 4% of the total mass was residual ammonia or water at bakeout conditions. Peak water and ammonia removal occurred around 275 deg. C and 150 deg. C respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Reveal of Uranium Bioremediation Mechanisms by Bacillus Species through Proteomics Studies

Radionuclides, such as Uranium (U) and heavy metals continue to pose threats to the ecosystem health and processes at the Department of Energy (DOE) managed, Savannah River Site (SRS), located along the Savannah River near Aiken, SC. Such co-contaminated environments are difficult to remediate using conventional excavation and disposal or pump-and-treat approaches. Globally, more than 109 tons of uranium contaminated areas pose a long term threat to human and ecological health. Even with presented low concentrations in the brain, central nervous effects are still observed. Uranium and depleted uranium (DU) have long term effects on the kidneys. Some small general health effects include severe headaches and breathing problems. Uranus ions are toxic to living cells because they inhibit metabolism of carbohydrates by blocking ATP binding sites. Bioremediation by microorganisms represents an alternative solution, which is advantageous because of the possibility of biosorbent regeneration, cost-effectiveness, increased metal removal and easy recovery of some valuable metals. Bacillus sp. bacterium was previously used in the bioremediation of heavy metals in coal mine run off waters of SRS. However, its ability to bioremediate uranium was unknown so far. Hence, in the present study, uranium bioremediation by Bacillus sp. bacterium was investigated. The mechanism of bioremediation was also revealed through proteomics studies. Heavy metals contamination poses a serious threat to water, soil and human health. Soil and water are contaminated due to excessive exploitation of uranium mines for generation of nuclear energy and weaponry. It is not degradable easily and persist in soil and water for a long period of time due to its long half- life. Savannah river site (SRS) is one of the uranium contaminated sites. The physical or chemical remediation techniques are costly and complex. Microbial system approaches with competent bacteria has received increased attention due to its adaptability in various environmental matrices and cost effectiveness. However, even though there are multiple suggested pathways (F1), the specific mechanisms that drive this behavior are still unclear, especially with popular microorganisms such as Bacillus species. In a previous research (Ibeanusi et al, 2003) Bacillus sp. was shown to detoxify and precipitate a variety of heavy metals in coal pile runoff waters of SRS site. Additionally, genomic analysis demonstrated that this microorganism posses multiple attributes for chemical transport regulation and metabolic pathways. U remediation occurs during the first 20 hours of exposure. During this time period, Bacillus sp. may work primarily under two mechanisms - sorption and accumulation. These two mechanisms simultaneously work to protect the microorganism from high concentrations. Figure 10 demonstrates that certain proteins are up regulated and down regulated under extreme stressful conditions. Membrane fraction proteins were up regulated. Cytosolic fraction proteins were down regulated. This protein information coincides with the adsorption behavior. Bacillus sp. is a good candidate for U remediation at various concentrations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

The Role of Titania Surface Coating by Atomic Layer Deposition in Improving Osteogenic Differentiation and Hard Tissue Formation of Dental Pulp Stem Cells

Recent studies have focused on modifying implant surface properties to improve bone regeneration and osseointegration. Herein, the role of titania surface coating in enabling dental pulp stem cells (DPSCs) differentiation and hard tissue formation is studied. Atomic layer deposition is applied at lower temperature to coat a nanolayer of titania onto hard and soft polybutadiene substrates without altering their moduli, to probe the effects of surface chemistry and substrate modulus. In the absence of titania, DPSCs prefer to attach and proliferate on the hard substrate, where particle-like biomineralization is present after 28 days in culture, whereas no biomineralization is observed on the soft substrate. Applying titania surface coating results in the improvement of adhesion and proliferation, regardless of substrate modulus, whereas cell and substrate moduli remain the same as control without titania coating. Furthermore, templated biomineralization is observed given the bone-like tissue composition by Raman analysis, in consistent with real time-polymerase chain reaction (RT-PCR) results showing upregulation of osteopontin (OPN) and bone sialoprotein (BSP), representing osteogenic differentiation. Furthermore, the results indicate that titania surface coating improved the ability to nucleate banded collagen fibers which in turn templated mineral deposits, and further induced the osteogenesis of DPSCs, regardless of its substrate modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Boosting the H 2 –D 2 Exchange Activity of Dilute Nanoporous Ti–Cu Catalysts through Oxidation–Reduction Cycle–Induced Restructuring

The use of nanoporous metals as catalysts has attracted significant interest in recent years. Their high-curvature, nanoscale ligaments provide not only high surface area but also a high density of undercoordinated step edge and kink sites. However, their long-term stability, especially at higher temperatures, is often limited by thermal coarsening and the associated loss of surface area. Herein, it is demonstrated that the nanoscale morphology of nanoporous Cu can be regenerated by applying oxidation/reduction cycles at 250 °C. Specifically, the morphological evolution and H 2 dissociation activity of hierarchical nanoporous Cu catalysts doped with Ti during structural rearrangement triggered by oxidative and reductive atmospheres at elevated temperatures are studied. In addition to coarsening of the structure at elevated temperatures, oxidation at 400 °C causes an expansion of the ligaments. Further, subsequent reduction at 400 °C leads to the formation of particles and a drop in the H 2 dissociation activity compared the fresh catalyst. However, performing the redox cycle at 250 °C reverses coarsening and boosts the H 2 dissociation activity for the hydrogen–deuterium (H 2 –D 2 ) reaction. Herein, the possibility to reverse coarsening is demonstrated, thereby mitigating the loss of activity frequently observed in nanoporous catalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solvent Impregnated Polymers Loaded with Liquid-Like Nanoparticle Organic Hybrid Materials for Enhanced Kinetics of Direct Air Capture and Point Source CO 2 Capture

Hybrid CO 2 capture materials, solvent impregnated polymers (SIPs), are developed based on a simple and scalable encapsulation technique to enhance CO 2 capture kinetics of water-lean solvents with high viscosity. Liquid-like nanoparticle organic hybrid materials functionalized with polyethylenimine (NOHM-I-PEI) are incorporated into a shell material and UV-cured to produce gas-permeable solid sorbents with uniform NOHMs loading (NPEI-SIPs). The CO 2 capture kinetics of NPEI-SIPs show a remarkable 50-fold increase compared to that of neat NOHM-I-PEI due to a large increase in the NOHMs-CO 2 interfacial surface area provided by the SIP design. The optimum NOHM-I-PEI loading and sorption temperature are found to be ≈49 wt% and 50 °C, respectively, and NPEI-SIPs exhibit great thermal stability over 20 CO 2 capture/sorbent regeneration temperature swing cycles. The pseudoequilibrium CO 2 loadings of NPEI-SIPs under humid conditions are as high as 3.1 mmol CO 2 g -1 NPEI - SIPs for 15 vol% CO 2 (postcombustion capture) and 1.7 mmol CO 2 g -1 NPEI - SIPs for 400 ppm (direct air capture). Overall, these findings suggest that NPEI-SIPs can effectively capture CO 2 from a wide range of CO 2 concentrations including direct air capture while allowing the flexible design of CO 2 capture reactors by combining the benefits of liquid solvents and solid sorbents.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding Degradation Mechanisms in SrIrO 3 Oxygen Evolution Electrocatalysts: Chemical and Structural Microscopy at the Nanoscale

Designing acid-stable oxygen evolution reaction electrocatalysts is key to developing sustainable energy technologies such as polymer electrolyte membrane electrolyzers but has proven challenging due to the high applied anodic potentials and corrosive electrolyte. This work showcases advanced nanoscale microscopy techniques supported by complementary structural and chemical characterization to develop a fundamental understanding of stability in promising SrIrO 3 thin film electrocatalyst materials. Cross-sectional high-resolution transmission electron microscopy illustrates atomic-scale bulk and surface structure, while secondary ion mass spectrometry imaging using a helium ion microscope provides the nanoscale lateral elemental distribution at the surface. After accelerated degradation tests under anodic potential, the SrIrO 3 film thins and roughens, but the lateral distribution of Sr and Ir remains homogeneous. A layer-wise dissolution mechanism is hypothesized, wherein anodic potential causes the IrO x -rich surface to dissolve and be regenerated by Sr leaching. Finally, the characterization approaches utilized herein and mechanistic insights into SrIrO 3 are translatable to a wide range of catalyst systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Roadmap for Sustainable Mixed Ionic–Electronic Conducting Membranes

Mixed ionic-electronic conducting (MIEC) membranes have gained growing interest recently for various promising environmental and energy applications, such as H 2 and O 2 production, CO 2 reduction, O 2 and H 2 separation, CO 2 separation, membrane reactors for production of chemicals, cathode development for solid oxide fuel cells, solar-driven evaporation and energy-saving regeneration as well as electrolyzer cells for power-to-X technologies. The purpose of this roadmap, written by international specialists in their fields, is to present a snapshot of the state-of-the-art, and provide opinions on the future challenges and opportunities in this complex multidisciplinary research field. As the fundamentals of using MIEC membranes for various applications become increasingly challenging tasks, particularly in view of the growing interdisciplinary nature of this field, a better understanding of the underlying physical and chemical processes is also crucial to enable the career advancement of the next generation of researchers. As an integrated and combined article, it is hoped that this roadmap, covering all these aspects, will be informative to support further progress in academics as well as in the industry-oriented research toward commercialization of MIEC membranes for different applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Turning Normal to Abnormal: Reversing CO 2 /C2–Hydrocarbon Selectivity in HKUST–1

Metal–organic frameworks (MOFs) can efficiently purify hydrocarbons from CO 2 , but their rapid saturation, driven by preferential hydrocarbon adsorption, requires energy-intensive adsorption–desorption processes. To address these challenges, an innovative approach is developed, enabling control over MOF flexibility through densification and defect engineering, resulting in an intriguing inverse CO 2 /C2 hydrocarbon selectivity. Here, in this study, the densification process induces the shearing of the crystal lattice and contraction of pores in a defective CuBTC MOF. These changes have led to a remarkable transformation in selectivity, where the originally hydrocarbon-selective CuBTC MOF becomes CO 2 -selective. The selectivity values for densified CuBTC are significantly reversed when compared to its powder form, with notable improvements observed in CO 2 /C 2 H 6 (4416 vs 0.61), CO 2 /C 2 H 4 (15 vs 0.28), and CO 2 /C 2 H 2 (4 vs 0.2). The densified material shows impressive separation, regeneration, and recyclability during dynamic breakthrough experiments with complex quinary gas mixtures. Simulation studies indicate faster CO 2 passage through the tetragonal structure of densified CuBTC compared to C 2 H 2 . Experimental kinetic diffusion studies confirm accelerated CO 2 diffusion over hydrocarbons in the densified MOF, attributed to its small pore window and minimal interparticle voids. This research introduces a promising strategy for refining existing and future MOF materials, enhancing their separation performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Coupling Interfacial Redox‐Reactions with In Situ Proton Generation for the Photoelectrochemical Separation of Rare‐Earth Elements

Abstract A dual‐function photoelectrochemical (PEC) separation system is demonstrated for rare‐earth element (REE) recovery. The sustainable release of the captured REEs is promoted through the synergistic integration of a redox‐reaction for electrostatic repulsion, and in situ proton generation for ion‐exchange, all driven by photoelectrochemistry. The platform consists of a redox‐copolymer, poly(ferrocenylpropyl methacrylamide‐ co ‐methacrylic acid) (P(FPMAm‐ co ‐MAA)) (PFM), conjugated with carbon nanotubes (CNTs) and coated onto titanium dioxide nanorods (TNRs). The (PFM‐CNT)/TNR spontaneously adsorbs up to 214.2 mg of Yttrium/g PFM by ion‐exchange, and demonstrates broad applicability for other REEs. The adsorbed REEs are released through the PEC oxidation of ferrocene (Fc) to ferrocenium (Fc + ), and the simultaneous PEC water splitting reactions at the TNRs that protonate the carboxylate binding groups. This dual photoelectrochemically‐driven mechanism for REE release is investigated by in situ pH measurements, as well as vibrational and X‐ray photoelectron spectroscopy. Through PEC approaches, a 68.8% reduction in energy consumption during REE recovery has been achieved compared to purely electrochemical systems, with a regeneration efficiency close to 100%. For NdFeB magnets from waste hard disk drives, Nd and Dy recovery efficiencies of 59.2 and 61.1% are achieved. The dual‐functionality of these copolymer PEC systems offers a sustainable platform for modulating critical element recovery.

Cho, Ki‐Hyun [Department of Chemical and Biomolecu↗
DOE OSTI2021

Uranium In Situ Electrolytic Deposition with a Reusable Functional Graphene-Foam Electrode

Nuclear fission produces 400 GWe which represents 11% of the global electricity output. Uranium is the essential element as both fission fuel and radioactive waste. Therefore, the recovery of uranium is of great importance. In this study, an in situ electrolytic deposition method to extract uranium from aqueous solution is reported. A functionalized reduced graphene oxide foam (3D-FrGOF) is used as the working electrode, which acts as both a hydrogen evolution reaction catalyst and a uranium deposition substrate. The specific electrolytic deposition capacity for U(VI) ions with the 3D-FrGOF is 4560 mg g –1 without reaching saturation, and the Coulombic efficiency can reach 54%. Moreover, reduction of the uranium concentration in spiked seawater from 3 ppm to 19.9 ppb is achieved, which is lower than the US Environmental Protection Agency uranium limits for drinking water (30 ppb). Furthermore, the collection electrode can be efficiently regenerated and recycled at least nine times without much efficiency fading, by ejecting into 2000 ppm concentrated uranium solution in a second bath with reverse voltage bias. All these findings open new opportunities in using free-standing 3D-FrGOF electrode as an advanced separation technique for water treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tuning Surface Acidity of Mixed Conducting Electrodes: Recovery of Si‐Induced Degradation of Oxygen Exchange Rate and Area Specific Resistance

Abstract Metal oxides are an important class of functional materials, and for many applications, ranging from solid oxide fuel/electrolysis cells, oxygen permeation membranes, and oxygen storage materials to gas sensors (semiconducting and electrolytic) and catalysts, the interaction between the surface and oxygen in the gas phase is central. Ubiquitous Si‐impurities are known to impede this interaction, commonly attributed to the formation of glassy blocking layers on the surface. Here, the surface oxygen exchange coefficient ( k chem ) is examined for Pr 0.1 Ce 0.9 O 2‐δ (PCO), a model mixed ionic electronic conductor, via electrical conductivity relaxation measurements, and the area‐specific resistance (ASR) by electrochemical impedance spectroscopy. It is demonstrated that even low silica levels, introduced by infiltration, depress k chem by a factor 4000, while the ASR increases 40‐fold and we attribute this to its acidity relative to that of PCO. The ability to fully regenerate the poisoned surface by the subsequent addition of basic Ca‐ or Li‐species is further shown. This ability to not only recover Si‐poisoned surfaces by tuning the relative surface acidity of an oxide surface, but subsequently outperform the pre‐poisoned response, promises to extend the operating life of materials and devices for which the catalytic oxygen/solid interface reaction is central.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Dihydroxyterephthalate—A Trojan Horse PET Counit for Facile Chemical Recycling

Abstract Here, low‐energy poly(ethylene terephthalate) (PET) chemical recycling in water: PET copolymers with diethyl 2,5‐dihydroxyterephthalate (DHTE) undergo selective hydrolysis at DHTE sites, autocatalyzed by neighboring group participation, is demonstrated. Liberated oligomeric subchains further hydrolyze until only small molecules remain. Poly(ethylene terephthalate‐ stat ‐2,5‐dihydroxyterephthalate) copolymers were synthesized via melt polycondensation and then hydrolyzed in 150–200 °C water with 0–1 wt% ZnCl 2 , or alternatively in simulated sea water. Degradation progress follows pseudo‐first order kinetics. With increasing DHTE loading, the rate constant increases monotonically while the thermal activation barrier decreases. The depolymerization products are ethylene glycol, terephthalic acid, 2,5‐dihydroxyterephthalic acid, and bis(2‐hydroxyethyl) terephthalate dimer, which could be used to regenerate virgin polymer. Composition‐optimized copolymers show a decrease of nearly 50% in the Arrhenius activation energy, suggesting a 6‐order reduction in depolymerization time under ambient conditions compared to that of PET homopolymer. This study provides new insight to the design of polymers for end‐of‐life while maintaining key properties like service temperature and mechanical properties. Moreover, this chemical recycling procedure is more environmentally friendly compared to traditional approaches since water is the only needed material, which is green, sustainable, and cheap.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magnesium‐Mediated Electrochemical Synthesis of Ammonia

Metal-mediated electrochemical synthesis of ammonia (NH3) is a promising method to activate N2 at room temperature. While a Li-mediated approach has been optimized to produce NH3 at high current density and selectivity, Li's scarcity and its highly negative plating potential limit scalability and energy efficiency. Alternative mediators have been proposed, but only Ca has shown some promise, achieving ≈50% Faradaic efficiency (FE), though requiring voltages beyond -3 V. Here, we report a Mg-mediated nitrogen reduction reaction (Mg-NRR), where N2 is activated on Mg to form Mg3N2, followed by protolysis to release NH3 and regenerate Mg. A notable NH3 FE of 25.28 ± 3.80% is achieved at a current density of -45 mA cm-2, corresponding to an NH3 partial current density of -11.30 ± 1.77 mA cm-2 under 6 bar N2. Isotope-labeled experiments confirm that NH3 originates from N2, with similar FE (25.15 ± 1.01%). Importantly, NH3 production is demonstrated at a total cell potential as low as -3 V. This Li-free Mg-NRR system offers key advantages, including lower energy input and use of earth-abundant materials, making it a scalable route for sustainable NH3 synthesis.

Goyal, Ishita↗
DOE OSTI2022

Scalable Direct Recycling of Cathode Black Mass from Spent Lithium‐Ion Batteries

Abstract End of life (EoL) lithium‐ion batteries (LIBs) are piling up at an intimidating rate, which is alarming for environmental health. With further expected rapid growth of LIB use, the magnitude of spent battery accumulation is also expected to grow. LiNi x Co y Mn z O 2 (NCM) cathode materials are a dominant chemistry in high energy LIBs, and make up a huge portion of this waste accumulation. Direct recycling is one of the most promising ways to turn this waste to wealth, but has been limited to lab‐scale, due to lack of robustness, namely the tedious pretreatment required that involves toxic organic solvents. Herein, a process that integrates the pretreatment and relithiation of the cathode black mass is demonstrated. Cathode material from EoL electric vehicle (EV) batteries is treated in a 100 g per batch operation and the regenerated cathode active material demonstrates 100% electrochemical performance recovery, with 91% yield rate, and shows promise for further scale up. This process has the advantages of integration, scalability, and universality, which clears the barricade for direct recycling to move from lab to industry scale with considerable profitability.

Chemistry↗
DOE OSTI2023

Two-Step Chemical Looping Cycle for Renewable NH 3 Production Based on Non-Catalytic Co 3 Mo 3 N/Co 6 Mo 6 N Reactions

A two-step solar thermochemical looping cycle based on Co 3 Mo 3 N/Co 6 Mo 6 N reduction/nitridation reactions offers a pathway for green NH 3 production that utilizes concentrated solar irradiation, H 2 O, and air as feedstocks. The NH 3 production cycle steps both derive process heat from concentrated solar irradiation and encompass 1) the reduction of Co 3 Mo 3 N in H 2 to Co 6 Mo 6 N and NH 3 ; and 2) nitridation of Co 6 Mo 6 N to Co 3 Mo 3 N with N 2 . Co 3 Mo 3 N reduction/nitridation reactions are examined at different H 2 and/or N 2 partial pressures and temperatures. NH 3 production is quantified in situ using liquid conductivity measurements coupled with mass spectrometry (MS). Solid-state characterization is performed to identify a surface oxygen layer that necessitates the addition of H 2 during cycling to prevent surface oxidation by trace amounts of O 2 . H 2 concentrations of > 5% H 2 /Ar and temperatures >500 °C are required to reduce Co 3 Mo 3 N to Co 6 Mo 6 N and form NH 3 at 1 bar. Complete regeneration of Co 3 Mo 3 N from Co 6 Mo 6 N is achieved at conditions of 700 °C under 25–75% H 2 /N 2 . H 2 pressure-swings are observed to increase NH 3 production during Co 3 Mo 3 N reduction. In conclusion, the results represent the first comprehensive characterization of and definitive non-catalytic production of NH 3 via chemical looping with metal nitrides and provide insights for technology development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Carbonic anhydrase textile structured packing for efficient CO 2 absorption in methyldiethanolamine solvent

Carbonic anhydrase (CA) is an attractive biodegradable catalyst for CO 2 absorption in solvent–based CO 2 capture. However, maintaining the stability of CA as a homogeneous component of the solvents is a challenge. Solvent regeneration temperature typically exceeds the enzyme thermal tolerance, which leads to CA deactivation. To reduce the need for frequent CA replenishment and to avoid inactive CA accumulation in the solvent, this work shows the benefits of an immobilization strategy where CA is fixed in a second–generation design of textile structured packing (CATSP–2) modules. The enzyme–immobilized packing showed 1.5 times better performance in CO 2 separation compared with traditional structured packing with a corresponding increased CO 2 loading in the rich solvent. The modules exhibited good CA activity retention of ~80% during the tests without any CA replenishment. As a result, applying CATSP–2 could potentially decrease the packing height and absorber column size for a lower cost per amount of CO 2 captured.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Anthraquinone Redox Relay for Dye‐Sensitized Photo‐electrochemical H 2 O 2 Production

Abstract Anthraquinone (AQ) redox mediators are introduced to metal‐free organic dye sensitized photo‐electrochemical cells (DSPECs) for the generation of H 2 O 2 . Instead of directly reducing O 2 to produce H 2 O 2 , visible‐light‐driven AQ reduction occurs in the DSPEC and the following autooxidation with O 2 allows H 2 O 2 accumulation and AQ regeneration. In an aqueous electrolyte, under 1 sun conditions, a water‐soluble AQ salt is employed with the highest photocurrent of up to 0.4 mA cm −2 and near‐quantitative faradaic efficiency for producing H 2 O 2 . In a non‐aqueous electrolyte, under 1 sun illumination, an organic‐soluble AQ is applied and the photocurrent reaches 1.8 mA cm −2 with faradaic efficiency up to 95 % for H 2 O 2 production. This AQ‐relay DSPEC exhibits the highest photocurrent so far in non‐aqueous electrolytes for H 2 O 2 production and excellent acid stability in aqueous electrolytes, thus providing a practical and efficient strategy for visible‐light‐driven H 2 O 2 production.

Sun, Jiaonan↗
DOE OSTI2020

A Strategy for Constructing Pore‐Space‐Partitioned MOFs with High Uptake Capacity for C 2 Hydrocarbons and CO 2

Abstract Introduction of pore partition agents into hexagonal channels of MIL‐88 type (acs topology) endows materials with high tunability in gas sorption. Here, we report a strategy to partition acs framework into pacs (partitioned acs) crystalline porous materials (CPM). This strategy is based on insertion of in situ synthesized 4,4′‐dipyridylsulfide (dps) ligands. One third of open metal sites in the acs net are retained in pacs MOFs; two thirds are used for pore‐space partition. The Co 2 V‐pacs MOFs exhibit near or at record high uptake capacities for C 2 H 2 , C 2 H 4 , C 2 H 6 , and CO 2 among MOFs. The storage capacity of C 2 H 2 is 234 cm 3 g −1 (298 K) and 330 cm 3 g −1 (273 K) at 1 atm for CPM‐733‐dps (the Co 2 V‐BDC form, BDC=1,4‐benzenedicarboxylate). These high uptake capacities are accomplished with low heat of adsorption, a feature desirable for low‐energy‐cost adsorbent regeneration. CPM‐733‐dps is stable and shows no loss of C 2 H 2 adsorption capacity following multiple adsorption–desorption cycles.

Wang, Yong↗