Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “redundancy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Power conditioning equipment for a thermoelectric outer planet spacecraft, volume 1, book 1

Equipment was designed to receive power from a radioisotope thermoelectric generator source, condition, distribute, and control this power for the spacecraft loads. The TOPS mission, aimed at a representative tour of the outer planets, would operate for an estimated 12 year period. Unique design characteristics required for the power conditioning equipment results from the long mission time and the need for autonomous on-board operations due to large communications distances and the associated time delays of ground initiated actions. The salient features of the selected power subsystem configuration are: (1) The PCE regulates the power from the radioisotope thermoelectric generator power source at 30 vdc by means of a quad-redundant shunt regulator; (2) 30 vdc power is used by certain loads, but is more generally inverted and distributed as square-wave ac power; (3) a protected bus is used to assure that power is always available to the control computer subsystem to permit corrective action to be initiated in response to fault conditions; and (4) various levels of redundancy are employed to provide high subsystem reliability.

Andrews, R. E.↗

A three-failure-tolerant computer system.

Two basic factors influence the design of highly reliable computer systems: the amount of failures required to be tol erated and the reliability or MTBF required. A computer system designed to tolerate any three single failures in a fail-operational-fail-operational-fail-safe manner for a real-time control application is presented. The design approach uses adaptive majority voting in both hardware and software with a four-level redundant system. Various methods of performing the adaptive majority voting functions were evaluated with the selected approach using a special module termed a voter-comparator switch (VCS). The VCS module allows the computer system to be operated in a variety of redundant modes, depending on the failure tolerance required at any particular time.

Koczela, L. J.↗

A fault-tolerant information processing concept for space vehicles.

A distributed fault-tolerant information processing system is proposed, comprising a central multiprocessor, dedicated local processors, and multiplexed input-output buses connecting them together. The processors in the multiprocessor are duplicated for error detection, which is felt to be less expensive than using coded redundancy of comparable effectiveness. Error recovery is made possible by a triplicated scratchpad memory in each processor. The main multiprocessor memory uses replicated memory for error detection and correction. Local processors use any of three conventional redundancy techniques: voting, duplex pairs with backup, and duplex pairs in independent subsystems.

Hopkins, A. L., Jr.↗

Analysis of a display and control system man-machine interface concept. Volume 1: Final technical report

An evaluation was made of the feasibility of utilizing a simplified man machine interface concept to manage and control a complex space system involving multiple redundant computers that control multiple redundant subsystems. The concept involves the use of a CRT for display and a simple keyboard for control, with a tree-type control logic for accessing and controlling mission, systems, and subsystem elements. The concept was evaluated in terms of the Phase B space shuttle orbiter, to utilize the wide scope of data management and subsystem control inherent in the central data management subsystem provided by the Phase B design philosophy. Results of these investigations are reported in four volumes.

Karl, D. R.↗

A study of modal coupling procedures for the space shuttle

Various procedures for analytically coupling two or more substructures to obtain modal data for assembly, using data obtained from mode surveys of the individual components are discussed. Particular attention was paid to the applicability of the techniques investigated to the space shuttle, with the possible replacement of full scale mode surveys of the shuttle assembly by component mode surveys along with analytical coupling. The synthesis procedures formulated in this report can all handle redundant connections, although the presence of redundancies does add complication to one of the techniques. All of the procedures use the test data directly, without going through an intermediate analytical model, and no analytical stiffness data is required to supplement the mode survey data. The coupling precedures were initially verified and evaluated by applying them to analytical check problems.

Goldenberg, S.↗

General considerations for structural inspection of older aircraft

Generalized considerations for structural inspections needed to maintain airworthiness of older aircraft are reviewed. Recommendations are made to account for accumulated service usage by counting flights rather than flight hours, to inspect structures made of flaw-sensitive materials more frequently than those made of flaw-tolerant materials, and to inspect structures having little redundancy more frequently than those having more redundancy. Occasional destructive inspections of high-time aircraft are suggested as being useful, but expensive, sources of either continued confidence or impending problems.

Hardrath, H. F.↗

A three-station lightning detection system

A three-station network is described which senses magnetic and electric fields of lightning. Directional and distance information derived from the data are used to redundantly determine lightning position. This redundancy is used to correct consistent propagation errors. A comparison is made of the relative accuracy of VLF direction finders with a newer method to determine distance to and location of lightning by the ratio of magnetic-to-electric field as observed at 400 Hz. It was found that VLF direction finders can determine lightning positions with only one-half the accuracy of the method that uses the ratio of magnetic-to-electric field.

Ruhnke, L. H.↗

Viking Orbiter 1975 articulation control subsystem design analysis

The articulation control subsystem, developed for the Viking Orbiter 1975 spacecraft, is a digital, multiplexed, closed-loop servo system used to control the pointing and positioning of the science scan platform and the high-gain communication antenna, and to position the solar-energy controller louver blades for the thermal control of the propellant tanks. The development, design, and anlaysis of the subsystem is preliminary. The subsystem consists of a block-redundant control electronics multiplexed among eight control actuators. Each electronics block is capable of operating either individually or simultaneously with the second block. This provides the subsystem the capability of simultaneous two-actuator control or a single actuator control with the second block in a stand-by redundant mode. The result of the preliminary design and analysis indicates that the subsystem will perform satisfactorily in the Viking Orbiter 1975 mission. Some of the parameter values used, particularly those in the subsystem dynamics and the error estimates, are preliminary and the results will be updated as more accurate parameter values become available.

Horiuchi, H. H.↗

Highly reliable processor system for space application.

Description of a redundant processor organization which can be implemented with off-the-shelf processors for fault-tolerant operation. Reconfiguration can be performed automatically in a transientless manner. To support this system configuration and redundancy management concept, an operating system referred to as a synchronous executive has been designed. This system is directed at real-time closed-loop space applications where minimum response time, no degradation of software solution, and system simplicity are of importance. The system is based on a multicomputer organization with each machine solving the same problem based on a common set of inputs. Processor status is fed to a higher-level device which selects a controlling processor for controlling outputs and monitoring computers for fault detection.

Tsou, H. S. E.↗

Spacecraft systems design trade-offs for the Earth Resources Technology Satellite.

The Earth Resources Technology Satellite Program's use of flight proven hardware in the design of a satellite for earth sensor payload support and data handling is discussed. The use of an existing satellite as the building block around which additional support systems such as the orbit adjust system, the redundant wideband telemetry systems, the second regulated power system, and the quad redundant command system is analyzed. System performance seen in orbit vs design objectives are discussed to point up the success of the design approach chosen. Also discussed are the schedule and cost benefits derived from the use of previously developed hardware with additional subsystems as required to meet program requirements.

Branchflower, G. A.↗

The development and test of a long-life, high reliability solar array drive actuator

To meet the life and reliability requirements of five to ten year space missions, a new solar array drive mechanism for 3-axis stabilized vehicles has been developed and is undergoing life testing. The drive employs a redundant lubrication system to increase its reliability. An overrunning clutch mechanism is used to permit block redundant application of two or more drives to a common array drive shaft. Two prototype actuator and clutch assemblies, in continuous vacuum life test under load at 10 to the minus 8th power torr for more than sixteen months, have each accumulated more than 34,000 output revolutions without anomaly, the equivalent of more than seven years of operation in a 1000 km orbit or nearly ninety-five years at synchronous altitude.

Kirkpatrick, D. L.↗

Design of a GN and C system to meet reliability goals

This paper analyzes the reliability of the guidance, navigation, and control (GNC) portion of an avionics system for the Space Shuttle Orbiter. This analysis shows how the GNC design is affected by the need to achieve an acceptable probability of successful completion of a mission and of safe return to an airport. It varies the redundancy of the inertial measurement unit (IMU), computers, and other time-critical elements. It also includes the reliability of the flight control electronics and of the nontime-critical sensors on a phase-by-phase basis. It shows that quadruple redundancy in certain subsystems, high quality parts, and cross-strapping on orbit are required.

Kayton, M.↗

Unpowered to powered failure rate ratio - A key reliability parameter

It is shown that the initial assumption of the ratio of unpowered to powered failure rates can have a strong influence on the design of a modular system intended for space missions. The analysis is performed for parallel systems and for triple modular redundant systems. Parallel systems are shown to be much more sensitive to the unpowered to powered failure rate ratio than the TMR/Spares systems, however, regardless of which standby redundancy technique is considered, the dependence of the system reliability on this ratio increases as the number of standby spares increases.

Taylor, D. S.↗

New development in high reliability strapdown platforms using TDF sensors

New development in high reliability strapdown navigation platform using two-degree-of-freedom sensors and redundancy concept is presented in this paper. The development is based on the assumption that each axis of the sensor can fail without affecting the remaining axis. The systems reliability is investigated, the optimum redundancy configurations are proposed, a technique of sensor performance management is developed for the proposed systems.

Tsuei, Y. D.↗

Central control element expands computer capability

Redundant processing and multiprocessing modes can be obtained from one computer by using logic configuration. Configuration serves as central control element which can automatically alternate between high-capacity multiprocessing mode and high-reliability redundant mode using dynamic mode switching in real time.

Easton, R. A.↗

Fail-safe system for activity cooled supersonic and hypersonic aircraft

A fail-safe-system concept was studied as an alternative to a redundant active cooling system for supersonic and hypersonic aircraft which use the heat sink of liquid-hydrogen fuel for cooling the aircraft structure. This concept consists of an abort maneuver by the aircraft and a passive thermal protection system (TPS) for the aircraft skin. The abort manuever provides a low-heat-load descent from normal cruise speed to a lower speed at which cooling is unnecessary, and the passive TPS allows the aircraft skin to absorb the abort heat load without exceeding critical skin temperature. On the basis of results obtained, it appears that this fail-safe-system concept warrants further consideration, inasmuch as a fail-safe system could possibly replace a redundant active cooling system with no increase in weight and would offer other potential advantages.

Jones, R. A.↗

A multiprocessor computer simulation model employing a feedback scheduler/allocator for memory space and bandwidth matching and TMR processing

A computer simulation model for a multiprocessor computer is developed that is useful for studying the problem of matching multiprocessor's memory space, memory bandwidth and numbers and speeds of processors with aggregate job set characteristics. The model assumes an input work load of a set of recurrent jobs. The model includes a feedback scheduler/allocator which attempts to improve system performance through higher memory bandwidth utilization by matching individual job requirements for space and bandwidth with space availability and estimates of bandwidth availability at the times of memory allocation. The simulation model includes provisions for specifying precedence relations among the jobs in a job set, and provisions for specifying precedence execution of TMR (Triple Modular Redundant and SIMPLEX (non redundant) jobs.

Bradley, D. B.↗

OMS engine shutoff valve and actuation system design and evaluation

Shutoff valve and actuation system concepts that are most suitable for the Orbital Maneuvering Systems engine application were determined. Emphasis was placed on the ten year and 100 mission life requirement, propellant and propellant residue compatibility and weight. It was found that poppet or ball valves utilizing electric or electropneumatic actuation were most applicable. Preliminary design layouts of a number of valve and actuation concepts were prepared and analyzed to make the optimum concept selection. Pneumatic actuation systems were required to feature their own pneumatic supply so that for the quad redundant valve, it was necessary to include two pneumatic supply systems, one for each of the series legs of the quad redundant package. The requirement for the pneumatic package placed heavy reliability, weight, and maintenance penalties upon electropneumatic actuation systems. The two valve and actuation systems concepts selected featured electric torque motor operation and a poppet as well as a ball valve concept with a retractable seal.

Wichmann, H.↗