Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

0D-1D Hybrid Silicon Nanocomposite as Lithium-Ion Batteries Anodes

Lithium ion batteries (LIBs) are the enabling technology for many of the societal changes that are expected to happen in the following years. Among all the challenges for which LIBs are the key, vehicle electrification is one of the most crucial. Current battery materials cannot provide the required power densities for such applications and therefore, it makes necessary to develop new materials. Silicon is one of the proposed as next generation battery materials, but still there are challenges to overcome. Poor capacity retention is one of those drawbacks, and because it is tightly related with its high capacity, it is a problem rather difficult to address with common and scalable fabrication processes. Here we show that combining 0D and 1D silicon nanostructures, high capacity and stability can be achieved even using standard electrode fabrication processes. Capacities as high as 1200 mAh/g for more than 500 cycles at high current densities (2 A/g) were achieved with the produced hybrid 0D/1D electrodes. In this research, it was shown that while 0D nanostructures provide good strain relaxation capabilities, 1D nanomaterials contribute with enhanced cohesion and conductive matrix integrity.

0D↗
DOE OSTI2021

Noncured Graphene Thermal Interface Materials for High-Power Electronics: Minimizing the Thermal Contact Resistance

We report on experimental investigation of thermal contact resistance, RC, of the noncuring graphene thermal interface materials with the surfaces characterized by different degree of roughness, Sq. It is found that the thermal contact resistance depends on the graphene loading, ξ, non-monotonically, achieving its minimum at the loading fraction of ξ ~15 wt%. Decreasing the surface roughness by Sq~1 μm results in approximately the factor of ×2 decrease in the thermal contact resistance for this graphene loading. The obtained dependences of the thermal conductivity, KTIM, thermal contact resistance, RC, and the total thermal resistance of the thermal interface material layer on ξ and Sq can be utilized for optimization of the loading fraction of graphene for specific materials and roughness of the connecting surfaces. Our results are important for the thermal management of high-power-density electronics implemented with diamond and other wide-band-gap semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hybrid Mesoporous Carbon/Copper Ferrite Electrode for Asymmetric Supercapacitors

Asymmetric supercapacitors (ASCs) with two dissimilar electrodes are known to exhibit relatively moderate energy and power densities. If electrodes derived from earth-abundant materials or renewable resources such as lignocellulosic biomass (LCB) are used for fabrication, energy storage systems are expected to become less expensive and more sustainable. Hybrid electrode materials have advantages such as higher surface area, better chemical stability, and superior energy density. This study reports on the synthesis of a novel hybrid electrode material containing porous carbon (POC) and copper ferrite, which is designated as POC@Cu-ferrite, and its electrochemical performance in ASC configuration. Corn stover derived hydrochar is utilized for the sol–gel synthesis of POC@Cu-ferrite hybrid material using earth-abundant Cu and Fe-based precursors. This material is characterized using X-ray diffraction (XRD), Raman spectroscopy, Brunauer–Emmett–Teller (BET) surface area analyzer, and scanning and transmission electron microscopy (SEM/TEM). As-synthesized Cu-ferrite is found to contain 89.2% CuFe 2 O 4 and 10.8% Fe 2 O 3 , whereas other phases such as Fe 3 O 4 , CuFeO 2 , and CuO are observed for the POC@Cu-ferrite. BET-specific surface area (SSA) and pore volume of POC@Cu-ferrite are observed as 1068 m 2 /g and 0.72 cm 3 /g, respectively. POC@Cu-ferrite hybrid electrode is used with POC opposite electrode to fabricate ASC, which is tested using Gamry G-300 potentiostat/galvanostat/ZRA to obtain cyclic voltammetry (CV) profiles and galvanostatic charge–discharge (GCD) plots. ASC is also prepared using Cu-ferrite and POC materials and its specific capacitance and stability are compared with ASCs prepared with POC@Cu-ferrite and POC or graphene nanoplatelets (GNPs) electrodes. POC@Cu-ferrite hybrid electrode is found to be superior with a 2-fold higher capacitance and significant electrochemical stability over 100 GCD cycles as compared to the Cu-ferrite electrode.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multichannel Fiber-Optic Silicon Fabry–Pérot Interferometric Bolometer System for Plasma Radiation Measurements

A single-channel fiber-optic bolometer system based on a high-finesse silicon Fabry–Pérot interferometer (FPI) was previously reported, intended to measure plasma radiation from the magnetically confined fusion chamber. Recently, we developed a multichannel fiber-optic bolometer system with five bolometers multiplexed using a coarse wavelength division multiplexer (CWDM) and interrogated with a white-light system involving a superluminescent light-emission diode source and a high-speed spectrometer. One of the bolometers was used as the reference bolometer to compensate for the ambient temperature variations, and the other four bolometers were used for radiation measurement. The bolometers have a simple structure with a silicon pillar at the end of the single-mode fiber and a gold disk on the other side of the silicon pillar. They are also easy to fabricate without stringent requirements on the optical alignment. Analysis of the system optimization was performed to improve the noise performance and to mitigate the vibration effect that may present in the practical application. The system had a significantly enhanced measurement range compared to the previous high-finesse FPI bolometer system for measuring radiation. Test results performed in air using a 405 nm laser as the radiation source showed that the temperature resolution and the noise-equivalent power density of the sensing bolometers connected to each channel of the CWDM were, respectively, ~0.4 mK and ~0.1 W/m2, with a time constant of ~220 ms, which is comparable to the previous more complicated fiber-optic bolometer systems based on high-finesse FPIs that were interrogated using wavelength-scanning lasers.

Uddin, Nezam↗
DOE OSTI2024

Composite Ionogel Electrodes for Polymeric Solid-State Li-Ion Batteries

Realizing rechargeable cells with practical energy and power density requires electrodes with high active material loading, a remaining challenge for solid-state batteries. Here, we present a new strategy based on ionogel-derived solid-state electrolytes (SSEs) to form composite electrodes that enable high active material loading (>10 mg/cm 2 , ~9 mA/cm 2 at 1C) in a scalable approach for fabricating Li-ion cells. By tuning the precursor and active materials composition incorporated into the composite lithium titanate electrodes, we achieve near-theoretical capacity utilization at C/5 rates and cells capable of stable cycling at 5.85 mA/cm 2 (11.70 A/g) with over 99% average Coulombic efficiency at room temperature. Finally, we demonstrate a complete polymeric solid-state cell with a composite anode and a composite lithium iron phosphate cathode with ionogel SSEs, which is capable of stable cycling at a 1C rate.

25 ENERGY STORAGE↗
DOE OSTI2026

Compressive Response and Energy Absorption of Additively Manufactured Elastomers with Varied Simple Cubic Architectures

Additive manufacturing, and particularly the vat photopolymerization process, enables the fabrication of complex geometries at high resolution and small length scales, making it well-suited for fabricating cellular structures (e.g., foams and lattices). Among these, elastomeric cellular structures are of growing interest due to their tunable compliance and energy dissipation. However, comprehensive data on the compressive behavior of these structures remains limited, especially for investigating the structure-property effects from changing the density and distribution of material within the cellular structure. This study explores how the mechanical response of polyurethane-based simple cubic structures changes when varying volume fraction, unit cell length, and unit cell patterning, which have not been systematically investigated previously in additively manufactured elastomers. Increasing volume fraction from 10% to 50% yielded significant changes in compressive stress–strain performance (decreasing strain at 0.5 MPa by 41.6% and increasing energy absorption density by 3962.5%). Although changing the unit cell length between 2.5 and 7 mm in ~30 mm parts did not result in statistically different stress–strain responses, modifying the configuration of struts of different thicknesses across designs with 30% volume fraction altered the stress–strain behavior (differences of 12.5% in strain at 0.5 MPa and 109.4% for energy absorption density). Power law relationships were developed to understand the interactions between volume fraction, unit cell length, and elastic modulus, and experimental data showed strong fits (R 2 > 0.91). These findings enhance the understanding of how multiple structural design aspects influence the performance of elastomeric cellular materials, providing a foundation for informing strategic design of tailorable materials for diverse mechanical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Binary Amplitude Reflection Gratings for X-ray Shearing and Hartmann Wavefront Sensors

New, high-coherent-flux X-ray beamlines at synchrotron and free-electron laser light sources rely on wavefront sensors to achieve and maintain optimal alignment under dynamic operating conditions. This includes feedback to adaptive X-ray optics. We describe the design and modeling of a new class of binary-amplitude reflective gratings for shearing interferometry and Hartmann wavefront sensing. Compact arrays of deeply etched gratings illuminated at glancing incidence can withstand higher power densities than transmission membranes and can be designed to operate across a broad range of photon energies with a fixed grating-to-detector distance. Coherent wave-propagation is used to study the energy bandwidth of individual elements in an array and to set the design parameters. We observe that shearing operates well over a ±10% bandwidth, while Hartmann can be extended to ±30% or more, in our configuration. We apply this methodology to the design of a wavefront sensor for a soft X-ray beamline operating from 230 eV to 1400 eV and model shearing and Hartmann tests in the presence of varying wavefront aberration types and magnitudes.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

RF operation of AlN/Al 0.25 Ga 0.75 N/AlN HEMTs with f T /f max of 67/166 GHz

Abstract We report on highly-scaled Al 0.25 Ga 0.75 N channel high electron mobility transistors. Regrown ohmic contacts covering the sidewall of the compressively strained Al 0.25 Ga 0.75 N channel exhibited a low contact resistance ofR c = 0.23 Ω · mm. Scaled devices with a T-shaped gate showed record high speed for any AlGaN-based transistors,f T /f max = 67/166 GHz, while simultaneously achieving high average breakdown field exceeding 2 MV cm −1 . The load-pull measurements performed at 10 GHz revealed a 20% peak power added efficiency with an output power density of 2 W mm −1 , which is mainly limited by the RF dispersion.

Physics↗
DOE OSTI2025

Temporal Properties of Compressible Magnetohydrodynamic Turbulence

Describing the temporal properties of compressible magnetohydrodynamic (MHD) turbulence is a fundamental problem that has important implications for particle acceleration and transport in astrophysical plasmas. Here, by carefully analyzing the spatial and temporal properties of compressible MHD turbulence, we derive a new spectral power density function that is supported by simulations. This new function reveals that the low-frequency fluctuations are dominated by modes with small parallel wavenumbers with respect to the mean background magnetic field. Furthermore, for fluctuations with dynamically significant parallel wavenumbers, broadening around their eigenfrequencies is described by this function, which is in close agreement with simulations. We use this formalism to present the scaling properties of individual MHD modes. Such broadening is a direct consequence of nonlinear processes and is different for the three fundamental MHD modes. Our results provide a new window to investigate the temporal properties of turbulence and will enable further studies on the interaction between compressible MHD turbulence and energetic plasmas.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Robust Measurement of Stellar Streams around the Milky Way: Correcting Spatially Variable Observational Selection Effects in Optical Imaging Surveys

Observations of density variations in stellar streams are a promising probe of low-mass dark matter substructure in the Milky Way. However, survey systematics such as variations in seeing and sky brightness can also induce artificial fluctuations in the observed densities of known stellar streams. These variations arise because survey conditions affect both object detection and star–galaxy misclassification rates. To mitigate these effects, we use Balrog synthetic source injections in the Dark Energy Survey (DES) Y3 data to calculate detection rate variations and classification rates as functions of survey properties. We show that these rates are nearly separable with respect to survey properties and can be estimated with sufficient statistics from the synthetic catalogs. Applying these corrections reduces the standard deviation of relative detection rates across the DES footprint by a factor of 5, and our corrections significantly change the inferred linear density of the Phoenix stream when including faint objects. Additionally, for artificial streams with DES-like survey properties we are able to recover density power spectra with reduced bias. We also find that uncorrected power-spectrum results for Legacy Survey of Space and Time (LSST)-like data can be around 5 times more biased, highlighting the need for such corrections in future ground-based surveys.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Artificial Neural Networks for In-Cycle Prediction of Knock Events

Downsized turbocharged engines have been increasingly popular in modern light-duty vehicles due to their fuel efficiency benefits. However, high power density in such engines is achieved thanks to high in-cylinder pressure and temperature conditions that increase knock propensity. Next-cycle control has been studied as a method to reduce the damaging effects of knock by operating the engine in a low knock probability condition. This exploratory study looks at the feasibility of in-cycle knock prediction as a tool for advanced knock control algorithms. A methodology is proposed to 1) choose in-cycle features of the pressure trace that highly correlate with knock events and 2) train artificial neural networks to predict in-cycle knock events before knock onset. The methodology was validated at different operating conditions and different levels of generalization. Precision and recall were used as metrics to evaluate the binary classifier. However, the Fowlkes-Mallows (FM) index was used to compare the result of the clustering algorithm at different operating conditions. The results showed a maximum FM index of 0.7 when the prediction was done at knock onset and a minimum FM index of 0.45 when the prediction was done at spark timing.

42 ENGINEERING↗
DOE OSTI2021

Multiphysics simulations of a steady-state lower hybrid current drive antenna for the FSNF

The Fusion Nuclear Science Facility (FNSF) is a proposed tokamak reactor with the mission to investigate operation of a fusion reactor in a nuclear environment. The high neutron fluence component of the FNSF mission requires steady-state operation for extremely long pulses (t_{pulse} ∼ months) at full power. Plasma sustainment and current drive will be critical components of a successful FNSF. COMSOL Multiphysics software is used for combined radiofrequency (RF) and thermal simulations of the lower hybrid current drive (LHCD) antenna system. These simu- lations consider the resistive RF losses in the antenna including realistic surface roughness and a range of potential materials. The thermal analysis adds volumetric nuclear heating, plasma heat flux on leading edges, and electromagnetic radiation from the plasma to the RF heating calculated by COMSOL. Additional neutronics calculations have been performed to determine the impact of these antenna designs on activated waste disposal for the materials considered. The simulations show that it is technically feasible to implement a fully-active multi-junction (FAM) rather than a passive-active multi-junction (PAM) style of antenna if the septum between adjacent waveguides is sufficiently wide and the thermal conductivity of the structural material is sufficiently high. The FAM has the benefit of higher achievable power density with respect to the PAM, which results in a more compact antenna with potentially lower impact on neutron shielding and tritium breeding. These considerations point to tungsten rather than steel as the preferred structural material in constructing the antenna.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Study of passively stable, fully detached divertor plasma regimes attained in innovative long-legged divertor configurations

Numerical modeling of divertor configurations with radially or vertically extended, tightly baffled, outer divertor legs has demonstrated the existence of a passively-stable fully detached divertor regime. In the simulations, long-legged divertors provide up to an order-of- magnitude increase in peak power handling capability compared to conventional divertors. The key physics for attaining the passively stable, fully detached regime in these simulations involves the interplay of strong convective plasma transport to the divertor leg outer sidewall, confinement of neutral gas in the divertor volume, geometric effects including a secondary X-point, and atomic radiation. New analysis shows that in this regime the detachment front location is set by the balance between the power entering the divertor leg and the losses to the walls of the divertor channel. Correspondingly, the maximum power that can be accommodated by the divertor, while still staying detached, increases with the poloidal length of the leg. The detached regime access window in terms of input power, density and impurity seeding concentration varies quantitatively depending on divertor geometry and modeling assumptions most specifically, cross-field transport to the side walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Lighting Policy Options to Incentivize the Circular Economy

Energy codes and energy efficiency policy are primed for significant shifts in the coming decade. Consumers are increasingly asking manufacturers to take responsibility for products over the course of the product lifespan, including at end-of-life. Consumer demand for social and environmental responsibility may push new codes and policies that incentivize the circular economy. Within the lighting sector, for example, rapid innovations have created large energy savings but also created a complex waste stream. Traditional energy code approaches to lighting efficiency have considered only lighting power density or energy-based metrics. Shifting codes and policy to consider environmental impacts of the product lifecycle could include circular economy mechanisms such as product deposits or service-based business models. In this paper we consider the possible structures for both codes and policies, and provide an analysis of the merits of each policy using life cycle assessment and sustainability index (SI).

Dillon, Heather↗
DOE OSTI2020

Generation IV Benchmarking of TRISO Fuel Performance Models Under Accident Conditions Final Report

The Generation IV International Forum (GIF) is a co-operative international endeavor of fourteen members organized to carry out the research and development needed to establish the feasibility and performance capabilities of the next generation nuclear energy systems. GIF selected six reactor technologies, amongst which is the Very High Temperature Reactor (VHTR) that is primarily dedicated to the cogeneration of electricity and hydrogen. The technical basis for VHTR is the tristructural isotropic (TRISO)-coated particle fuel, the graphite as the core structure, helium coolant, as well as the dedicated core layout and lower power density to removal decay heat in a natural way. At the heart of safety features of the VHTR concept lie the TRISO fuel particles that are designed to keep their structural integrity and retain fission products at temperatures up to 1600°C. As part as the design and future operation of VHTRs, a key aspect is the accurate prediction of fuel performance under irradiation and accident conditions. Modeling and simulation allow prediction of TRISO fuel behavior when subject to neutron flux and in high temperature accident scenarios. The refinement of the fuel performance models and codes is performed by comparison to in-pile and out-of-pile experimental data that reproduce the expected irradiation conditions in high temperature gas-cooled reactors (HTGRs). Historically, the International Atomic Energy Agency (IAEA) developed a benchmark dedicated to the validation of predictive methods for fuel and fission product behavior through the Coordinated Research Program CRP-2 (IAEA, 1997). CRP-2 was later updated to cover fuel fabrication, quality assurance, irradiation performance, safety testing, and spent fuel. The scope of the resulting CRP-6 benchmarks focused on HTGR fuel performance and fission product release (IAEA, 2012). Taking advantage of additional TRISO fuel fabrication, irradiation, and safety testing campaigns, GIF launched a Generation IV Benchmarking of TRISO Fuel Performance Models under Accident Conditions in late 2015. This GIF benchmark is a three-year program steered by Idaho National Laboratory (INL, USA). The other participants include the Japan Atomic Energy Agency (JAEA, Japan) and the Korea Atomic Energy Research Institute (KAERI, Korea). The objectives of the benchmark are to: follow on the IAEA CRP benchmarks, (2) model fission product release under accident conditions, (3) compare results obtained by the fuel performance modeling codes of the benchmark participants, and (4) compare these code predictions to experimental data. Safety tests chosen for modeling include the first and second experiments of the Advanced Gas Reactor program (AGR-1 and AGR-2) and the High Flux Reactor (HFR) EU1bis experiment. This report presents the results obtained by the three research institutions using their respective fuel performance modeling codes. Comparisons of the corresponding fission product release predictions are made with experimental data from AGR-1, AGR-2, and HFR-EU1bis. The benchmark results show good agreements between all participants but also show a general trend of over-prediction of the experimental release data, which is mainly attributed to the use of over-estimated diffusion coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Dynamic System Scaling Application to Accelerated Nuclear Fuel Testing

The development of nuclear fuel and materials requires a continuous effort to investigate the acute and prolonged effects of irradiation, thermal-material stress, chemical change, or other conceivable damage mechanics acquired during normal operation or accident scenarios throughout its lifetime. As in-core fuel property measurement techniques advance to support in the real-time, non-invasive, and enhanced accuracy realm, it is the future of fuel development to pursue to higher degrees of control, predictability of integral test behavior via separate effects test (SET), and shorter test time intervals. The fuel development life cycle from initial concept to commercial licensing is approximated to be 20 years and current literature suggests by optimizing fuel performance codes with SETs, the process could possibly be compressed to 5 to 10 years. Recently, a research group in the Idaho National Laboratory (INL) is testing reduced scale fuel rods and increased power density to accelerate evolution of fuel phenomena in metallic fuels. In support of nuclear fuel rod development, compressing fuel test process, and accelerating fuel phenomena, it was the purpose of this study to investigate nuclear fuel performance phenomena via literature review and effectively scale the initial conditions, boundary conditions, and geometric properties to describe the time-dependent response including to fuel burnup, thermal and mechanical stress, transmutations and inter-diffusion, and other relevant observed phenomena. The study was based on BISON simulations of historic EBR-II metallic fuel experiments and Dynamical System Scaling (DSS) method are utilized to assess effects of scaling activity including fuel phenomena acceleration and calculations of time-dependent distortions. The research successfully scaled metallic fuel phenomena, accelerated fuel testing, and assessed the distortions for each scaled case derived.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Runtime localized cooling of high-performance processors

A plurality of thermal electric cooler (TEC) elements are formed in a TEC grid structure. Control logic dynamically varies a supply current supplied to each TEC element (or group of TEC elements) in the TEC grid based on changes in power density respectively associated with areas cooled by each of the TEC elements or group of TEC elements.

Rao, Karthik↗
DOE OSTI2022

Solving Critical Problems of the Muon Collider Higgs Factory: Optics, Magnets and their Protection, Detector Backgrounds

A low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). Magnet designs are proposed which provide high operating gradient and magnetic field in a large aperture to accommodate the large size of muon beams (due to low beta*), as well as a cooling system to intercept the large heat deposition from the showers induced by decay electrons. The distribution of heat deposition in the MC SR lattice elements requires large-aperture magnets in order to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intensive simulations, a sophisticated radiation protection system was designed for the collider SR and IR to bring the peak power density in the superconducting coils below the quench limit and reduce the dynamic heat deposition in the cold mass by a factor of 100. The system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in the magnet aperture optimized individually for each magnet. These also reduce the background particle fluxes in the collider detector.

43 PARTICLE ACCELERATORS↗