SEARCH · Engineering Papers

Results for “plastic work”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Phase-field modeling of crack growth and mitigation in solid oxide cells

Fracture and crack growth is one of the main degradation mechanisms in solid oxide cells (SOCs). However, the modeling of crack growth in SOCs is challenging due to their complex microstructures and possible plasticity development within the Ni particles in Ni-based SOC electrodes. In this study, a phase-field fracture model is developed, which incorporates the SOC microstructures and phase-dependent material properties, including yield strength, fracture toughness in the bulk and at the interphase boundaries. The model is employed to study crack initiation and growth under thermal and redox cycling on the hydrogen electrode side of SOCs. The simulation results demonstrate that under thermal cycling, work-zone cracking dominates in electrolyte-supported SOCs with cracks initiated at the triple-phase boundaries, while only minor mechanical degradation occurs in hydrogen-electrode-supported SOCs after hundreds of thermal cycles. Under redox cycling, through-cracking of yttria-stabilized zirconia (YSZ) in the hydrogen electrode and electrolyte layers dominates. Finally, the simulation results suggest several crack-mitigation strategies, including decreasing the porosity in the hydrogen electrode support layer and synchronizing thermal strain to balance oxidation strain.

08 HYDROGEN↗

DOE OSTI2021

Effect of natural gamma background radiation on portal monitor radioisotope unmixing

It is well known that national security relies on several layers of protection. One of the most important is the traffic control at borders and ports that exploits Radiation Portal Monitors (RPMs) to detect and deter potential smuggling attempts. Most portal monitors rely on plastic scintillators to detect gamma rays. Despite their poor energy resolution, their cost effectiveness and the possibility of growing them in large sizes make them the gamma-ray detector of choice in RPMs. Unmixing algorithms applied to organic scintillator spectra can be used to reliably identify the bare and unshielded radionuclides that triggered an alarm, even with fewer than 1000 detected counts and in the presence of two or three nuclides at the same time. In this work, we experimentally studied the robustness of a state-of-the-art unmixing algorithm to different radiation background spectra, due to varying atmospheric conditions, in the 16 °C to 28 °C temperature range. In the presence of background, the algorithm is able to identify the nuclides present in unknown radionuclide mixtures of three nuclides, when at least 1000 counts from the sources are detected. With fewer counts available, we found larger differences of approximately 35.9% between estimated nuclide fractions and actual ones. In these low count rate regimes, the uncertainty associated by our algorithm with the identified fractions could be an additional valuable tool to determine whether the identification is reliable or a longer measurement to increase the signal-to-noise ratio is needed. Moreover, the algorithm identification performances are consistent throughout different data sets, with negligible differences in the presence of background types of different intensity and spectral shape.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2021

Atomistic processes of surface-diffusion-induced abnormal softening in nanoscale metallic crystals

Abstract Ultrahigh surface-to-volume ratio in nanoscale materials, could dramatically facilitate mass transport, leading to surface-mediated diffusion similar to Coble-type creep in polycrystalline materials. Unfortunately, the Coble creep is just a conceptual model, and the associated physical mechanisms of mass transport have never been revealed at atomic scale. Akin to the ambiguities in Coble creep, atomic surface diffusion in nanoscale crystals remains largely unclear, especially when mediating yielding and plastic flow. Here, by using in situ nanomechanical testing under high-resolution transmission electron microscope, we find that the diffusion-assisted dislocation nucleation induces the transition from a normal to an inverse Hall-Petch-like relation of the strength-size dependence and the surface-creep leads to the abnormal softening in flow stress with the reduction in size of nanoscale silver, contrary to the classical “alternating dislocation starvation” behavior in nanoscale platinum. This work provides insights into the atomic-scale mechanisms of diffusion-mediated deformation in nanoscale materials, and impact on the design for ultrasmall-sized nanomechanical devices.

36 MATERIALS SCIENCE↗

DOE OSTI2024

New dynamic diamond anvil cell for time-resolved radial x-ray diffraction

The dynamic diamond anvil cell (dDAC) is a recently developed experimental platform that has shown promise for studying the behavior of materials at strain rates ranging from intermediate to quasi-static and shock compression regimes. Combining dDAC with time-resolved x-ray diffraction (XRD) in the radial geometry (i.e., with incident x-rays perpendicular to the axis of compression) enables the study of material properties such as strength, texture evolution, and deformation mechanisms. This work describes a radial XRD dDAC setup at beamline P02.2 (Extreme Conditions Beamline) at DESY’s PETRA III synchrotron. Time-resolved radial XRD data are collected for titanium, zirconium, and zircon samples, demonstrating the ability to study the strength and texture of materials at compression rates above 300 GPa/s. In addition, the simultaneous optical imaging of the DAC sample chamber is demonstrated. The ability to conduct simultaneous radial XRD and optical imaging provides the opportunity to characterize plastic strain and deviatoric strain rates in the DAC at intermediate rates, exploring the strength and deformation mechanisms of materials in this regime.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

New dynamic diamond anvil cell for time-resolved radial x-ray diffraction

47 OTHER INSTRUMENTATION↗

NASA NTRS1978

Development and evaluation of elastomeric materials for geothermal applications

A material for a casing packer for service for 24 hours in a geothermal environment was developed by synthesis of new elastomers and formulation of available materials. Formulation included use of commercial elastomer gumstocks and also crosslinking of plastic (high Tg) materials. Fibrous reinforcement of fluorocarbon rubbers was emphasized. Organic fiber reinforcement did not increase hot properties significantly. Glass fiber reinforcement gave significant increase in tensile properties. Elongation was reduced, and the glass-reinforced composition examined so far did not hold up well in the geothermal environment. Colloidal asbestos fibers were also investigated. A few experiments with polyphenyl ether gave material with low tensile and high compression set. Available high styrene SBR compositions were studied. Work to date suggests that new synthetic polymers will be required for service in geothermal environments.

Mueller, W. A.↗

NASA NTRS2016

Atmospheric Pressure Plasma Jet as a Dry Alternative to Inkjet Printing in Flexible Electronics

We have developed an atmospheric pressure plasma jet printing system that works at room temperature to 50 deg C unlike conventional aerosol assisted techniques which require a high temperature sintering step to obtain desired thin films. Multiple jets can be configured to increase throughput or to deposit multiple materials, and the jet(s) can be moved across large areas using a x-y stage. The plasma jet has been used to deposit carbon nanotubes, graphene, silver nanowires, copper nanoparticles and other materials on substrates such as paper, cotton, plastic and thin metal foils.

Printable electronics↗

DOE OSTI2024

Chapter 4: Physically informed deep learning networks for simulating microstructure evolution of 3D polycrystals

As discussed in the previous chapter, high energy diffraction microscopy (HEDM) is used to study the micromechanical evolution of a material during in situ loading. HEDM experiments have been used to verify crystal plasticity (CP) simulations [119, 91, 90, 120], for experimental planning, material design, and to further analyze experimental results. However, Fast Fourier transform-based CP (CP-FFT) or finite element-based CP (CP-FE) methods are often too slow to be used in real-time during an experiment. CP-FFT is faster than CP-FE simulations due to the absence of meshing, but can still take hours to simulate the response of a single volume depending on the size and number of strain steps [127]. Reducing computation time would create a larger exploration space in planning and design, and enable faster analysis of experimental results and real-time feedback during an experiment. This research expands upon previous works to develop a workflow for predicting the full-field evolution of a 3D polycrystal. The workflow is simplified from previous works to predict only orientation and elastic strain tensors (from which stress tensors are calculated). The network is physically informed through loss functions and network architecture for a more robust model. The orientation predictions are informed about the cubic crystal symmetry of the material by incorporating disorientation and misorientation information into the network architecture and loss. The Von Mises stress is used to enforce the correct stress-strain trends in the strain tensor predictions. Additional total strain steps from the elastic and elastoplastic region are included to better capture the stress-strain evolution at smaller total strain steps. Material and hardening parameters are additional inputs into the networks to further inform the network and to study the network’s ability to predict different materials other than those used for training.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Convection in Scaled Turbine Internal Cooling Passages With Additive Manufacturing Roughness

Abstract Additive manufacturing processes, such as direct metal laser sintering (DMLS), enable the creation of novel turbine cooling internal passages and systems. However, the DMLS method produces a significant and unique surface roughness. Previous work in scaled passages analyzed pressure losses and friction factors associated with the rough surfaces, as well as investigated the velocity profiles and turbulent flow characteristics within the passage. In this study, the heat transfer characteristics of scaled additively manufactured surfaces were measured using infrared (IR) thermography. Roughness panels were CNC machined from plates of aluminum 6061 to create near isothermal roughness elements when heated. Fluid resistance differences between the aluminum roughness panels and roughness panels constructed from ABS plastic using the same roughness patterns from McClain et al. (2020, “Flow in a Simulated Turbine Blade Cooling Channel With Spatially Varying Roughness Caused by Additive Manufacturing Orientation,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-16069) were investigated. Finally, the overall thermal performance enhancements and friction losses were assessed through the calculation of surface averaged “global thermal performance” ratios. The global thermal performance characterizations indicate results in-line with those found for traditional commercial roughness and slightly below traditional internal passage convection enhancement methods such as swirl chambers, dimples, and ribs. The passages investigated in this study do not include compressibility effects or the long-wavelength artifacts and channel geometric deviations observed by Wildgoose et al. (2020, “Impact of Additive Manufacturing on Internal Cooling Channels with Varying Diameters and Build Directions,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-15049). However, the results of this study indicate that, based on the roughness augmentation alone, artificial convective cooling enhancers such as turbulators or dimples may still be required for additively manufactured turbine component cooling.

Engineering↗

NASA NTRS1997

Micromechanical Modeling of Woven Metal Matrix Composites

This report presents the results of an extensive micromechanical modeling effort for woven metal matrix composites. The model is employed to predict the mechanical response of 8-harness (8H) satin weave carbon/copper (C/Cu) composites. Experimental mechanical results for this novel high thermal conductivity material were recently reported by Bednarcyk et al. along with preliminary model results. The micromechanics model developed herein is based on an embedded approach. A micromechanics model for the local (micro-scale) behavior of the woven composite, the original method of cells (Aboudi), is embedded in a global (macro-scale) micromechanics model (the three-dimensional generalized method of cells (GMC-3D) (Aboudi). This approach allows representation of true repeating unit cells for woven metal matrix composites via GMC-3D, and representation of local effects, such as matrix plasticity, yarn porosity, and imperfect fiber-matrix bonding. In addition, the equations of GMC-3D were reformulated to significantly reduce the number of unknown quantities that characterize the deformation fields at the microlevel in order to make possible the analysis of actual microstructures of woven composites. The resulting micromechanical model (WCGMC) provides an intermediate level of geometric representation, versatility, and computational efficiency with respect to previous analytical and numerical models for woven composites, but surpasses all previous modeling work by allowing the mechanical response of a woven metal matrix composite, with an elastoplastic matrix, to be examined for the first time. WCGMC is employed to examine the effects of composite microstructure, porosity, residual stresses, and imperfect fiber-matrix bonding on the predicted mechanical response of 8H satin C/Cu. The previously reported experimental results are summarized, and the model predictions are compared to monotonic and cyclic tensile and shear test data. By considering appropriate levels of porosity, residual stresses, and imperfect fiber-matrix debonding, reasonably good qualitative and quantitative correlation is achieved between model and experiment.

Bednarcyk, Brett A.↗

DOE OSTI2024

Microwave-Assisted Syngas Cleanup: Catalytic Reforming of Gasifier Tar Using a Low-Cost Iron Catalyst

The microwave-assisted gasification of plastic wastes to produce hydrogen-rich syngas is an attractive energy-saving plastic upcycling route, and the addition of biomass could improve the quality of the syngas produced; however, it could also increase the tar yield, which is an undesired, secondary product in this process. The presence of tars could result in downstream lines blockage, reactor down time and costly maintenance. Therefore, reducing or removing tar is desired. Due to its chemical complexity, toluene, which is one of the main tar constituents, could be used as a model tar compound. In this work, the microwave-assisted catalytic dry reforming of toluene was studied using Fe/Al2O3 as a catalyst, under CO2 at different reaction temperatures. The toluene reforming reaction was conducted using microwave and conventional thermal reactors. The results showed that under microwave irradiation, higher CO2 and toluene conversions, as well as better hydrogen yield can be observed compared to conventional toluene reforming at the same reaction temperature. The catalyst stability test was also investigated. Three reaction pathways were observed during microwave reaction.

Bai, Xinwei↗

DOE OSTI2024

Mitigation of distortion of Al/steel part under simulated paint baking condition: Experiment and numerical model studies

Multi-material joining of lightweight structures is essential to reduce vehicle weight for more energy savings and less greenhouse gas emission. However, mismatch of thermal expansion coefficient for dissimilar materials during the paint baking process can induce part distortion and joint failure for adhesive bonding. Here, in the present work, a thermomechanical model based on contact mechanics and large deformation theory was developed for dissimilar high-strength Al alloy and steel components to study the distortion mechanism and influential factors of the residual gap. The established model was used to optimize joint conditions, such as pitch distance and part geometry. When a weld pitch is shorter than 100 mm, the maximum gap between Al and steel part can be greatly reduced to 0.1 mm, and the local stress and plastic strain around the joint during the oven heating and cooling cycle are also substantially reduced compared with the long pitch case (900 mm). The numerical modeling results revealed that a comparable bending stiffness ratio between the steel and Al cross sections is critical to the minimization of gap and distortion under paint baking condition. Digital image correlation technique was used to measure the overall part distortion and local strain distribution that were used to validate the model prediction. Weld bonding (adhesive bonding with friction bit joining) process was successfully employed to join Al to steel component without gap opening in adhesive after the paint baking and cooling.

36 MATERIALS SCIENCE↗

NASA NTRS1978

A case of elasto-plastic flow using a new special element

Using a new special element for elasto-plastic flow, a nearly square, center-cracked plate of simulated A533 steel is analyzed. Selected results are examined locally to the crack's tip. It is found that a sharp transition in the distribution of deformation and stress occurs after the initial elastic response, and that this state is followed by fairly stable behavior over a considerable portion of the load range. Distribution of strain energy density is noted, and implications for use of the parameter J and for additional work are discussed briefly.

Swedlow, J. L.↗

DOE OSTI2021

Enhanced biomechanical performance of additively manufactured Ti-6Al-4V bone plates

As the global trauma fixation devices market expands rapidly, it is imperative to improve the production of fixation devices through enhanced design accuracy and fit for best performance and maximum patient comfort. Selective laser melting (SLM) is one of the mature additive manufacturing methods, which provides a viable route for the rapid production of such devices. In this work, the ability of SLM to produce near-net-shape parts, as desired for medical implants, was utilized for the fabrication of bone plates from Ti-6Al-4V alloy powder. Martensitic microstructure obtained after the printing of alloy resulted in poor ductility, limiting its application in the field of orthopedics. A specially designed repeated cyclic heating and cooling close to but below the β-transus was used to transform from acicular to a bimodal microstructure without the need for plastic deformation prior to heat treatment for improving the ductility. Bone plates subjected to this heat treatment were mechanically tested by means of tensile and 3-point bend tests and demonstrated large improvement in ductility, and the values were comparable to those similar plates prepared from wrought alloy. Other important properties required for implants were assessed, such as corrosion resistance in simulated body fluid and cytocompatibility in vitro using MC3T3-E1 cells. These results for the bone plate after heat treatment were excellent and similar to those of the additively manufactured and wrought plates. Taken together, the performance of the additively manufactured bone plates after subjecting to heat treatment was similar to those of bone plate manufactured using wrought alloy. These results have important implications for the fabrication of patient-specific metallic orthopedic devices using SLM without compromising their biomechanical performance by subjecting them to a tailored heat treatment.

36 MATERIALS SCIENCE↗

NASA NTRS2005

Experiments and Models for Polymeric Microsphere Foams

The current project was performed under the direction of Dr. Byron Pipes as its lead investigator from January 2001 to August 2004. With the permission of the NASA, the project was transferred to Dr. Thein Kyu as the principle investigator for the period of September 2004 - June 2005. There were two major thrust areas in the original proposal; (1) experimental characterization and kinematics of foam structure formation and (2) determination of the mechanical, physical, and thermal properties, although these thrust areas were further sub- divided into 7 tasks. The present project has been directed primarily to elucidate kinematics of micro-foam formation (tasks 1 and 3) and to characterize micro-foam structures, since the control of the micro-structure of these foams is of paramount importance in determining their physical, mechanical and thermal properties. The first thrust area was accomplished in a timely manner; however, the second thrust area of foam properties (tasks 2,4-7) has yet to be completed because the area of kinematics of foam structure formation turned out to be extremely complex and thus consumed more time than what have been anticipated. As will be reported in what follows, the present studies have greatly enhances the in-depth understanding of mechanisms and kinematics of the micro-foam formation from solid powders. However, in order to implement all objectives of the second thrust areas regarding investigations of mechanical, physical, and thermal properties and establishment of the correlation of structure - properties of the foams, the project needs additional time and resources. The technical highlights of the accomplishment are summarized as follows. The present study represents a first approach to understanding the complexities that act together in the powder foaming process to achieve the successful inflation of polyimide microstructures. This type of study is novel as no prior work had dissected the fundamentals that govern the inflation process in this type of systems. The systematic approach to each of the different phenomena (i.e. morphological, diffusive, kinetic and dynamic) brings into context each of them in a way that allows separate understanding and analysis. Of the different phenomena studied, probably the one that gives a higher level of control over the inflation process has been shown to be the morphological aspects of the precursor particles. It is a major contribution of the present work to isolate and identify this phenomenon and highlight the features that with careful control during the synthesis of the precursor material can lead to a highly optimized and specialized final product (neat foam or microstructure). Some of these accomplishments have been presented in various national meetings and some of which are either published in refereed journals or still in various stages of publications. One of the presentations was selected for "Best of ANTEC 2004" Online Presentation Series of the Society of Plastics Engineers (SPE) (September 2004)

Pipes, R. Byrona↗

DOE OSTI2020

An Integrated Multiscale Experimental-Numerical Analysis on Reconsolidation of Salt-Clay Mixture for Disposal of Heat-Generating Waste (Final NEUP Technical Report)

The overall purpose of this research is to improve understanding of THMC coupling effect on the reconsolidation of granular (or crushed) salt-clay mixture used for seal systems of shafts and drifts in salt repositories. This proposed work is partially motivated by the recent work on the Waste Isolation Pilot Plant (WIPP) that shows the promising sealing capability of clay-salt mixture compared to crushed salt. In particular, primary emphasis is to develop a fully integrated multiscale experiment-numerical study to determine and explain what leads to the superior sealing ability of the clay-salt mixture. These research activities are designed to seek further understanding of (1) why clay additives may enhance the fluid trapping and (2) whether this flow barrier effect may prevail under different combinations of temperature, confining pressure, deviatoric stress and other foreseeable environmental factors. If successful, this enhanced flow trapping ability of the seal provides significant improvement to the seal and repository performance and therefore make the repository safer in the long-term. The experiment component includes microstructural investigation and macroscopic tests on a reconsolidated salt-clay mixture. In the microstructural study, the goal is to (1) characterize microscopic distributions of distinct phases (e.g., clay, salt crystal boundaries, trapped brine, and pore) to examine the connectivity of the pore network inside the salt-clay mixture with different amounts of clay additive and moisture content and (2) analyze multiscale imaging data to reconstruct the polycrystalline microstructures for numerical simulations. Meanwhile, macroscopic tests are performed to analyze how clay alters the failure/creep mechanisms in the salt-clay mixture. Microscopic and macroscopic experimental observations will both be used to calibrate and validate a multiscale model that explicitly simulates the capillary and multiphase flow in the connected pores and the deformation due to the presence of intra-crystalline brine at the pore scale via a new polyhedral discrete element–lattice Boltzmann method (DEM-LBM) coupling model. The pore-scale simulations are homogenized via an upscaling procedure that converts pore-scale information (e.g. force exerted on grain boundary, sliding, pressure-solution) to continuum measures (e.g. Cauchy stress, Darcy’s flow) at each integration point in the macroscopic multiphase TMHC model. This multiscale scheme will allow coupling be- tween high-fidelity simulations of brine-salt-clay interaction and the macroscopic TMHC model. The multiscale model helps the understanding of how the trapped brine inclusion affects the pressure-solution mechanism with the presence of clay and moisture. This work brings new insight into the sealing capacity of salt-clay mixture under elevated temperature over a long period of time - a key to evaluating the potential of salt-clay mixture usage for salt repositories.

42 ENGINEERING↗

DOE OSTI2023

Friction Extrusion: Solid-State Metal Synthesis and Recycling in Sustainable Manufacturing

Friction extrusion (FE) is a novel solid-state process for synthesis and recycling of metals and alloys. The novelty of FE is that it utilizes the frictional heating and extensive plastic deformation intrinsic in the process to stir, mechanically alloy, consolidate, and convert powders, chips, and other recyclable feedstock metals into a usable product form of highly engineered materials. FE represents a potentially transformational sustainable manufacturing technology. Being a solid-state process, it eliminates the energy-intensive melting and solidification steps, which are necessary in the conventional metal recycle and synthesis processes. Therefore, FE is a highly energy-efficient, practically zero-emission, and economically competitive process. Here, in this work, the concept and configuration of FE are introduced, the energy-saving advantage of FE is analyzed, the feasibility of FE is demonstrated with synthesizing Al alloys, and the results of some metallographic and mechanical properties studies are presented. A prognosis of the friction extrusion technology is outlined.

36 MATERIALS SCIENCE↗

NASA NTRS2014

Test Facility Simulation Results for Aerospace Loss-of-Lubrication of Spur Gears

Prior to receiving airworthiness certification, extensive testing is required during the development of rotary wing aircraft drive systems. Many of these tests are conducted to demonstrate the drive system's ability to operate at extreme conditions, beyond that called for in the normal to maximum power operating range. One of the most extreme tests is referred to as the loss-of-lubrication or run dry test. During this test, the drive system is expected to last at least 30 min without failure while the primary lubrication system is disabled for predetermined, scripted flight conditions. Failure of this test can lead to a partial redesign of the drive system or the addition of an emergency lubrication system. Either of these solutions can greatly increase the aircraft drive system cost and weight and extend the schedule for obtaining airworthiness certification. Recent work at NASA Glenn Research Center focused on performing tests, in a relevant aerospace environment, to simulate the behavior of spur gears under loss-of-lubrication conditions. Tests were conducted using a test facility that was used in the past for spur gear contact fatigue testing. A loss-oflubrication test is initiated by shutting off the single into mesh lubricating jet. The test proceeds until the gears fail and can no longer deliver the applied torque. The observed failures are typically plastically deformed gear teeth, due to the high tooth temperatures, that are no longer in mesh. The effect of several different variables to gear tooth condition during loss-of-lubrication have been tested such as gear pitch, materials, shrouding, lubrication condition, and emergency supplied mist lubrication in earlier testing at NASA. Recent testing has focused on newer aerospace gear steels and imbedding thermocouples in the shrouding to measure the air-oil temperatures flung off the gear teeth. Along with the instrumented shrouding, an instrumented spur gear was also tested. The instrumented spur gear had five thermocouples installed at different locations on the gear tooth and web. The data from these two types of measurements provided important information as to the thermal environment during the loss-of-lubrication event. This data is necessary to validate on-going modeling efforts.

Gears↗