Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical pulses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Application of optical fibers to wide-band differential interferometry

A broadband differential optical interferometer that uses an optical-fiber waveguide to transmit coherent light to a surface under inspection is discussed. Input laser light is coupled into two single-mode optical fibers in a stationary input optics enclosure. The fibers transmit the light to a small, remote detection head where it is used in a wide-band differential interferometer to detect continuous and pulsed surface-particle displacements. The effective separation between the input optics and the detection head allows simple surface scanning and probe alignment. Detection of simulated acoustic emission pulses by a prototype test unit is reported.

Garg, A. O.↗
NASA NTRS1995

Laser-Induced Incandescence Calibration via Gravimetric Sampling

Various beam imaging and/or sheet forming optics delivered light at 1064 nm from a pulsed Nd:YAG laser for use either as a beam of 3 mm radius or as a laser sheet. Imaging measurements were performed with a grated intensified array camera equipped with an ultraviolet f4.5 lens and a 40 mm extension tube. Point measurements were performed using an ultraviolet 250 mm focal length lens to collect and focus the laser induced incandescence (LII) signal into a 1 meter long quartz optical fiber which directed the LII signal to a 1/4 meter monochromator. An aperture preceding the lens restricted the signal collection region to 1 cm along the laser beam at the center of the gravimetric chimney. Signals from the PMT were processed by a boxcar integrator whereas the images were captured digitally using a frame-grabber with 16 MByte of on-board memory. Both 'point' and planar measurements were made with detector gates of 250 ns to minimize possible morphology bias in collection of the LII signal. Additionally, the imaging measurements were performed with broadband spectral collection of the LII signal to maximize the signal and again minimize any potential effects of morphology dependent heating and/or cooling rates. Digital delay generators controlled the firing of he laser, detector gates and data acquisition. Neutral density filters were used for both sets of measurements to maintain signal levels within linear dynamic ranges of the detectors, the range being determined prior to experiments.

VanderWal, R. L.↗
DOE OSTI2024

Circularly Polarized Attosecond Pulses Enabled by an Azimuthal Phase and Polarization Grating

High-harmonic generation (HHG) is an extreme nonlinear optical process that can map the properties of an infrared driving laser beam onto short wavelength attosecond pulse trains. However, current techniques for generating circularly polarized high harmonics for probing magnetic materials and chiral systems have limitations: two-color collinear counter-rotating driving lasers result in a low cutoff photon energy, while single-color non-collinear counter-rotating schemes suffer from low conversion efficiency. In this work, we generate circularly polarized attosecond pulse trains by using a structured laser driver which has a rotating polarization and phase grating along the azimuthal coordinate. Furthermore, our experimental and numerical results demonstrate the production of left and right circularly polarized harmonics, which naturally separate upon propagation. Our approach uses a single laser color in a collinear geometry, that can be scaled for high efficiency. Simulations show this scheme can extend into the soft x-ray region when driven by mid-infrared driving lasers, while preserving the same high phase-matching cutoff photon energy as for linearly-polarized high harmonics.

attosecond science↗
DOE OSTI2020

Acousto-optic modulators of high-power laser radiation on the basis of KGW and KYW crystals

Different modifications of acousto-optic modulators (AOMs) based on KG(WO{sub 4}){sub 2} (KGW) and KY(WO{sub 4}){sub 2} (KYW) crystals, designed for Q switching of high-power pulsed lasers, is developed and investigated. It is shown that AOMs based on these crystals are universal, can be combined with different lasers in the wavelength range of 1 – 3 μm, and have a high radiation resistance in the absence of antireflection coatings and light input at Brewster’s angle. The operation efficiency of KGW-based AOMs is experimentally demonstrated. Solid-state lasers based on Cr : Er : YSGG (λ = 2.78 μm), Cr : Yb : Ho : YSGG (λ = 2.87 μm), Cr : Tm : Ho : YSGG (λ = 2.09 μm), and Nd : YAG (λ = 1.064 μm) crystals with active acousto-optic Q switching, operating in the repetitively pulsed regime with a high beam quality and without surface destruction, are investigated. Lasing pulses (30 – 60)-ns long with energy up to 32 mJ at a repetition rate from 1 to 1000 Hz are obtained. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1981

Detection of acoustic emission in composites by optical fiber interferometry

Acoustic emission in prestressed composite panels using embedded single mode optical fiber was detected. Static loading of the composite matrix produces acoustic emission events, pulsed ultrasonic waves, which mechanically modulate the embedded fiber geometry and phase modulate the transmitted optical field. The modulation is detected by optical interferometry and Fourier optical processing techniques to produce an electronic signal proportional to acoustic field amplitude integrated along the length of the fiber in the specimen. Static and dynamic calibration of the detection system is discussed and frequency domain characterization of the acoustic field interaction with the fiber is presented.

Wade, J. C.↗
NASA NTRS1991

Pulse-Width-Modulating Driver for Brushless dc Motor

High-current pulse-width-modulating driver for brushless dc motor features optical coupling of timing signals from low-current control circuitry to high-current motor-driving circuitry. Provides high electrical isolation of motor-power supply, helping to prevent fast, high-current motor-driving pulses from being coupled through power supplies into control circuitry, where they interfere with low-current control signals.

Salomon, Phil M.↗
NASA NTRS2012

Dark Material at the Surface of Polar Crater Deposits on Mercury

Earth-based radar measurements [1-3] have yielded images of radar-bright material at the poles of Mercury postulated to be near-surface water ice residing in cold traps on the permanently shadowed floors of polar impact craters. The Mercury Laser Altimeter (MLA) on board the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft has now mapped much of the north polar region of Mercury [4] (Fig. 1). Radar-bright zones lie within polar craters or along poleward-facing scarps lying mainly in shadow. Calculations of illumination with respect to solid-body motion [5] show that at least 0.5% of the surface area north of 75deg N lies in permanent shadow, and that most such permanently shadowed regions (PSRs) coincide with radar-bright regions. MLA transmits a 1064-nm-wavelength laser pulse at 8 Hz, timing the leading and trailing edges of the return pulse. MLA can in some cases infer energy and thereby surface reflectance at the laser wavelength from the returned pulses. Surficial exposures of water ice would be optically brighter than the surroundings, but persistent surface water ice would require temperatures over all seasons to remain extremely low (<110 K). Thermal models [6,7] incorporating direct and scattered radiation, Mercury s eccentric orbit, 3:2 spin-orbit resonance, and near-zero obliquity generally do not support such conditions in all permanently shadowed craters but suggest that water ice buried near the surface (<0.5 m depth) could survive for > 1 Gy. We describe measurements of reflectivity derived from MLA pulse returns. These reflectivity data show that surface materials in the shadowed regions are darker than their surroundings, enough to strongly attenuate or extinguish laser returns. Such measurements appear to rule out widespread surface exposures of water ice. We consider explanations for the apparent low reflectivity of these regions involving other types of volatile deposit.

Neumann, Gregory A.↗
DOE OSTI2022

Influence of Annealing and Composition on the Crystal Structure of Mixed-Halide, Ruddlesden–Popper Perovskites

Mixed-halide two-dimensional (2D) hybrid organic–inorganic perovskites offer an important opportunity to control the band gap for applications in optoelectronic devices. In this study, we focus on phenethylammonium lead halide [(PEA) 2 Pb(I 1– x Br x ) 4 ] films, the pure iodide form of which is one of the most widely studied optically active 2D perovskite systems. Resonant infrared, matrix-assisted pulsed laser evaporation is used to grow films to explore the effects of post-growth annealing and mixed-halide composition. The composition, crystal structure, and optical properties are studied for as-grown and annealed films of (PEA) 2 Pb(I 1– x Br x ) 4 for x = 0, 0.25, 0.5, 0.75, and 1. First-principles calculations are used in conjunction with the experimental data to explain the mixed-halide behavior that does not trend monotonically with the bromide content. Important results of this work are as follows: (i) X-ray diffraction reveals evidence for halide phase separation around x = 0.25, consistent with first-principles calculations, whereas no phase separation is observed for x = 0.5 and above and (ii) a unique photoluminescence (PL) peak splitting is observed for x = 0.75, a composition for which no compositional phase separation is observed. The PL splitting is tentatively explained by the coexistence of two distinct types of halide short-range ordering at x = 0.75. Overall, this study demonstrates that mixed-halide n = 1 Ruddlesden–Popper perovskites are not simple random alloys but that instead, they display distinct sites and ordering preferences of the different halide anions. These preferences are critical to understand and rationally tune the properties of the materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Identification of contamination in the pulse-compression chamber of the OMEGA EP Laser System originating from clean room garments

The contamination of optical components with microscopic particles strongly impacts their ability to handle high-power or high-intensity laser pulses via an array of mechanisms. This work explores the nature and origin of a subset of contamination particles found inside the pulse-compression chamber of the OMEGA EP Laser System. Using Raman microscopy accompanied by other analytical methods, it was shown that sodium nitrate constitutes a significant fraction of the particles that possess diameters on the order of a few micrometers. Further investigation aiming to reveal the origin of these particles suggests that these sodium nitrate particles are deposited via shedding from the reusable clean room garments worn in the Laser Bay and compression chamber. Raman microscopy also revealed various plastic particles such as polystyrene, polyethylene, and poly(diallyl isophthalate).

Raman spectroscopy↗
DOE OSTI2022

A cryogenic torsion balance using a liquid-cryogen free, ultra-low vibration cryostat

We describe a liquid-cryogen free cryostat with ultra-low vibration levels, which allows for continuous operation of a torsion balance at cryogenic temperatures. The apparatus uses a commercially available two-stage pulse-tube cooler and passive vibration isolation. Here, the torsion balance exhibits torque noise levels lower than room temperature thermal noise by a factor of about four in the frequency range of 3–10 mHz, limited by residual seismic motion and by radiative heating of the pendulum body. In addition to lowering thermal noise below room-temperature limits, the low-temperature environment enables novel torsion balance experiments. Currently, the maximum duration of a continuous measurement run is limited by accumulation of cryogenic surface contamination on the optical elements inside the cryostat.

47 OTHER INSTRUMENTATION↗
NASA NTRS2004

Reflectance Spectra of CM2 Chondrite Mighei Irradiated with Pulsed Laser and Implications for Low-Albedo Asteroids and Martian Moons

Micrometeoritic bombardment is an important space weathering process modifying surface optical properties of airless solar system bodies. We have used irradiation with a microsecond pulsed laser as an experimental method to simulate such a process on various targets. The experiment discussed here was performed on a powdered sample of CM2 carbonaceous chondrite Mighei. Shingareva et al. report the details of experimental procedure as well as the results of mineralogical and chemical studies of the irradiated material. Here we present reflectance spectra of irradiated Mighei samples and discuss their spectral properties compared to those of non-irradiated meteorite and low-albedo small solar system bodies.

Moroz, L. V.↗
DOE OSTI2020

Technology of thin-rod Yb : YAG amplifiers with a high pulse energy and average power

Technology for producing thin-rod Yb : YAG laser amplifiers is improved, which is aimed at increasing the output pulse energy and includes the development of a new method for mounting active elements into a cooling system and employment of more persistent dielectric coatings of rod ends. An influence of a thermal lens on the beam size in an active element is theoretically studied and the parameters are found, which provide equal beam sizes at input and output rod ends. The output pulse energy of 4 mJ is obtained without optical breakdown of the output end, which substantially exceeds the previously obtained results. The amplifier demonstrates an average power of 60 W and maintains a high beam quality. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1974

Electron beam fluorescence system to measure gas density in impulse facilities

Very rapid measurements, ranging from a few microsecond to milliseconds in duration, characterize studies made in shock regions or behind them. A system to measure gas density under such conditions in a 15.24-cm (6-in.) expansion tube is described. The basic elements are an electron beam of moderate energy and high current capability, an optical detector, and the associated electronics and data readout equipment. A heated-cathode electron gun, capable of pulsed operation and delivering up to 200 milliamperes current, provides the source of electrons. Optics include a simple collector lens, aperture, collimator lens, filters, and a photomultiplier tube. The photomultiplier output signal was recorded by means of photographed oscilloscope traces for pulsed beam operation.

Hoppe, J. C.↗
DOE OSTI2025

Laser-Induced Spectral Diffusion of T Centers in Silicon Nanophotonic Devices

Color centers in silicon are emerging as spin-photon interfaces operating at telecommunication wavelengths. The nanophotonic device integration of silicon color centers via ion implantation leads to significant optical-linewidth broadening, which makes indistinguishable photon generation challenging. Here, we study the optical spectral diffusion of T centers in a silicon photonic crystal cavity. We investigate the linewidth-broadening timescales and origins by measuring the temporal correlations of the resonance frequency under different conditions. Spectral hole-burning measurements reveal no spectral broadening at short timescales from 102 ns to 725 ns. We probe broadening at longer timescales using a check pulse to herald the T-center frequency and a probe pulse to measure the frequency after a wait time. The optical resonance frequency is stable up to 3 ms in the dark. Laser pulses below the silicon band gap applied during the wait time lead to linewidth broadening. Our observations establish laser-induced processes as the dominant spectral-diffusion mechanism for T centers in devices and inform materials and feedback strategies for indistinguishable photon generation.

Zhang, Xueyue↗
NASA NTRS1994

Numerical Simulations of Self-Focused Pulses Using the Nonlinear Maxwell Equations

This paper will present results in computational nonlinear optics. An algorithm will be described that solves the full vector nonlinear Maxwell's equations exactly without the approximations that are currently made. Present methods solve a reduced scalar wave equation, namely the nonlinear Schrodinger equation, and neglect the optical carrier. Also, results will be shown of calculations of 2-D electromagnetic nonlinear waves computed by directly integrating in time the nonlinear vector Maxwell's equations. The results will include simulations of 'light bullet' like pulses. Here diffraction and dispersion will be counteracted by nonlinear effects. The time integration efficiently implements linear and nonlinear convolutions for the electric polarization, and can take into account such quantum effects as Kerr and Raman interactions. The present approach is robust and should permit modeling 2-D and 3-D optical soliton propagation, scattering, and switching directly from the full-vector Maxwell's equations. Abstract of a proposed paper for presentation at the meeting NONLINEAR OPTICS: Materials, Fundamentals, and Applications, Hyatt Regency Waikaloa, Waikaloa, Hawaii, July 24-29, 1994, Cosponsored by IEEE/Lasers and Electro-Optics Society and Optical Society of America

Goorjian, Peter M.↗
DOE OSTI2022

Dispersive optical systems for scalable Raman driving of hyperfine qubits

Hyperfine atomic states are among the most promising candidates for qubit encoding in quantum information processing. In atomic systems, hyperfine transitions are typically driven through a two-photon Raman process by a laser field which is amplitude modulated at the hyperfine qubit frequency. Here we introduce a method for generating amplitude modulation by phase modulating a laser and reflecting it from a highly dispersive optical element known as a chirped Bragg grating. This approach is passively stable, offers high efficiency, and is compatible with high-power laser sources, enabling large Rabi frequencies and improved quantum coherence. We benchmark this approach by globally driving an array of approximately 300 neutral 87 Rb atomic qubits trapped in optical tweezers and obtain Rabi frequencies of 2 MHz with photon-scattering error rates of less than 2×10 -4 per π pulse. This robust approach can be directly integrated with local addressing optics in both neutral atom and trapped ion systems to facilitate high-fidelity single-qubit operations for quantum information processing.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRS1993

Data analysis for GOPEX image frames

The data analysis based on the image frames received at the Solid State Imaging (SSI) camera of the Galileo Optical Experiment (GOPEX) demonstration conducted between 9-16 Dec. 1992 is described. Laser uplink was successfully established between the ground and the Galileo spacecraft during its second Earth-gravity-assist phase in December 1992. SSI camera frames were acquired which contained images of detected laser pulses transmitted from the Table Mountain Facility (TMF), Wrightwood, California, and the Starfire Optical Range (SOR), Albuquerque, New Mexico. Laser pulse data were processed using standard image-processing techniques at the Multimission Image Processing Laboratory (MIPL) for preliminary pulse identification and to produce public release images. Subsequent image analysis corrected for background noise to measure received pulse intensities. Data were plotted to obtain histograms on a daily basis and were then compared with theoretical results derived from applicable weak-turbulence and strong-turbulence considerations. Processing steps are described and the theories are compared with the experimental results. Quantitative agreement was found in both turbulence regimes, and better agreement would have been found, given more received laser pulses. Future experiments should consider methods to reliably measure low-intensity pulses, and through experimental planning to geometrically locate pulse positions with greater certainty.

Levine, B. M.↗
NASA NTRS1982

PPM demodulation for Reed-Solomon decoding for the optical space channel

The use of Reed-Solomon (RS) block codes over the pulse position modulated (PPM) frames to obtain the largest degree of error correction is considered. Since RS codes can correct both symbol errors and symbol erasures, a question arises as to the best way to demodulate the PPM laser fields in order to generate the input symbols for the RS decoder. The method selected for demodulating (converting the received laser field to digital symbols) defines the erasure and transmitted symbols of the laser link, and therefore determines the work error probabilities of the system. Several demodulating schemes are considered, and the effect of each on RS decoding performance computed. This computation was carried out for various optical receiver models. It is shown that simple threshold decisioning of pulse slots produces performance that degrades as the background noise increases. This is caused by the generation of too many erasures for the RS decoder to handle. A decision scheme, delta-max demodulation which offers improvement over threshold decisioning by redefining the generation of an erasure is proposed.

Divsalar, D.↗