Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “new”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

New photomultiplier active base for Hall C Jefferson Lab lead tungstate calorimeter

A new photomultiplier tube active base was designed and tested. The base combines active voltage division circuit and fast amplifier, powered by the current flowing through voltage divider. This base is developed to upgrade older photomultiplier bases of Jefferson Lab lead-tungsten calorimeter (about ˜1200 crystals of PbWO{sub 4} from the PrimEx experimental setup). This is needed for the extension of detectors' rate capability to meet requirements of new Hall C proposal PR12-11-102 of measurements of the L/T separated cross sections and their ratio R = πL/πT in neutral-pion p(e,e'π0)p deep exclusive and p(p(e,e'π{sup 0})p)X semi-inclusive scattering regions. New active base is direct replacement of older passive base circuit without adding of additional power or signal lines. However, it extends detectors rate capability with factor over 20. Moreover, transistorized voltage divider improves detector's amplitude resolution due to reduction of photomultiplier gain dependence from tube anode current. The PMT active base is the invention disclosed in V. Popov's U.S. Patent No. 6,791,269, which successfully works over ten years in several Jefferson Lab Cherenkov detectors. The following design is a new revised and improved electronic circuit with better gain stability and linearity in challenge to meet requirements of new Hall C experimental setup. New active base performance was tested using fast LED light source and Pr:LuAG scintillator and gamma sources. Electronics radiation hardness was tested on JLab accelerator. Results of testing R4125 Hamamatsu photomultiplier tube in new active base are presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

SU-E-T-376: Evaluation of a New Stereotactic Diode for Small Field Dosimetry

Purpose: To evaluate the performance of a new stereotactic diode for dosimetry of small photon fields. Methods: A new stereotactic diode, consisting of an unshielded p-type silicon chip, and with improved radiation hardness energy dependence was recently developed (IBA Dosimetry, Schwarzenbruch, Germany). The diode has an active volume of 0.6 mm dia. x 0.02 mm thick. Two new diodes were evaluated, one which was pre-irradiated to 100kGy with 10 MeV electrons and another which received no prior irradiation. Sensitivity, stability, reproducibility, and linearity as a function of dose were assessed. Beam profiles and small field output factors were measured on a CyberKnife (CK) and compared with measurements using two commercially available diodes. Results: The new diodes exhibit linear behavior (within 0.6%) over a dose range 0.02 – 50 Gy; a commercially available device exhibits excursions of up to 4% over the same range. The sensitivity is 4.1 and 3.8 nC/Gy for the un-irradiated and pre-irradiated diodes, respectively. When irradiated with 150 Gy in dose increments of 5, 20 and 35 Gy, both new diodes provide a stable response within 0.5%. Output factors measured with the two new diodes are identical and compare favorably with other commercially available diodes and published data. Similarly, no differences in measured field size or penumbra were observed among the devices tested. Conclusion: The new diodes show excellent stability and sensitivity. The beam characterization in terms of output factors and beam profiles is consistent with that obtained with commercially available diodes.

60 APPLIED LIFE SCIENCES↗

TU-CD-303-02: Beyond Radiation Induced Double Strand Breaks - a New Horizon for Radiation Therapy Research

Recent advances in cancer research have shed new light on the complex processes of how therapeutic radiation initiates changes at cellular, tissue, and system levels that may lead to clinical effects. These new advances may transform the way we use radiation to combat certain types of cancers. For the past two decades many technological advancements in radiation therapy have been largely based on the hypothesis that direct radiation-induced DNA double strand breaks cause cell death and thus tumor control and normal tissue damage. However, new insights have elucidated that in addition to causing cellular DNA damage, localized therapeutic radiation also initiates cascades of complex downstream biological responses in tissue that extend far beyond where therapeutic radiation dose is directly deposited. For instance, studies show that irradiated dying tumor cells release tumor antigens that can lead the immune system to a systemic anti-cancer attack throughout the body of cancer patient; targeted irradiation to solid tumor also increases the migration of tumor cells already in bloodstream, the seeds of potential metastasis. Some of the new insights may explain the long ago discovered but still unexplained non-localized radiation effects (bystander effect and abscopal effect) and the efficacy of spatially fractionated radiation therapy (microbeam radiation therapy and GRID therapy) where many “hot” and “cold” spots are intentionally created throughout the treatment volume. Better understanding of the mechanisms behind the non-localized radiation effects creates tremendous opportunities to develop new and integrated cancer treatment strategies that are based on radiotherapy, immunology, and chemotherapy. However, in the multidisciplinary effort to advance new radiobiology, there are also tremendous challenges including a lack of multidisciplinary researchers and imaging technologies for the microscopic radiation-induced responses. A better grasp of the essence of these advances in cancer biology research will give medical physicists a new perspective in daily clinical physics practice and in future radiation therapy technological development. Furthermore, academic medical physics should continue to be an integral part of the multidisciplinary cancer research community, harnessing our newly acquired understanding of radiation effects, and developing novel cost-effective treatment strategies to better combat cancer. Learning Objectives: Understand that localized radiation can lead to non-localized secondary effects such as radiation-induced immune response, bystander effect, and abscopal effect. Understand that the non-localized radiation effects may be harnessed to improve cancer treatment. Learn examples of physics participation in multidisciplinary research to advance cancer biology. Recognize the challenges and possibilities of physics applications in cancer research. Chang: NIH 5RC2CA148487-02 and 1U54CA151652-01 Graves: IDEA award (19IB-0106) from the California Breast Cancer Research Program (CBCRP), and by NIH P01 CA67166.

60 APPLIED LIFE SCIENCES↗

A new form of the calibration curve in radiochromic dosimetry. Properties and results

Purpose: This work describes a new form of the calibration curve for radiochromic dosimetry that depends on one fit parameter. Some results are reported to show that the new curve performs as well as those previously used and, more importantly, significantly reduces the dependence on the lot of films, the film orientation on the scanner, and the time after exposure. Methods: The form of the response curve makes use of the net optical densities ratio against the dose and has been studied by means of the Beer–Lambert law and a simple modeling of the film. The new calibration curve has been applied to EBT3 films exposed at 6 and 15 MV energy beams of linear accelerators and read-out in transmission mode by means of a flatbed color scanner. Its performance has been compared to that of two established forms of the calibration curve, which use the optical density and the net optical density against the dose. Four series of measurements with four lots of EBT3 films were used to evaluate the precision, accuracy, and dependence on the time after exposure, orientation on the scanner and lot of films. Results: The new calibration curve is roughly subject to the same dose uncertainty, about 2% (1 standard deviation), and has the same accuracy, about 1.5% (dose values between 50 and 450 cGy), as the other calibration curves when films of the same lot are used. Moreover, the new calibration curve, albeit obtained from only one lot of film, shows a good agreement with experimental data from all other lots of EBT3 films used, with an accuracy of about 2% and a relative dose precision of 2.4% (1 standard deviation). The agreement also holds for changes of the film orientation and of the time after exposure. Conclusions: The dose accuracy of this new form of the calibration curve is always equal to or better than those obtained from the two types of curves previously used. The use of the net optical densities ratio considerably reduces the dependence on the lot of films, the landscape/portrait orientation, and the time after exposure. This form of the calibration curve could become even more useful with new optical digital devices using monochromatic light.

60 APPLIED LIFE SCIENCES↗

Search for New Light Bosons in Higgs Boson Decays

The Standard Model (SM) of particle physics is a theory that summarizes our current knowledge about the most fundamental constituents of matter and interactions between them. The Higgs boson is a central part of the SM as it provides masses to all other particles. After many decades of searches for it, on the 4th of July 2012 CERN announced a discovery of a new particle by CMS and ATLAS collaborations at the Large Hadron Collider (LHC). The properties of the new particle and the properties of the Higgs boson predicted by the SM are consistent at the level of precision of current measurements. The extensive physics program of the LHC experiments includes searches for new physics beyond the SM which complement further precision measurements of the properties of the new particle. These searches may lead to earlier confirmation that the particle is not the SM Higgs boson in case the new physics is found. This dissertation is dedicated to a search for decays of the newly discovered particle to pairs of new light bosons, each of which decays into the μ+μ- final state. The data set corresponds to an integrated luminosity of 5.3 fb^-1 of proton-proton collisions at √s = 7 TeV, recorded by the CMS experiment at the LHC in 2011. No excess of events above the SM predictions is observed. A model-independent upper limit of 0.86 fb on the product of the cross section times branching fraction times acceptance is set. The obtained limit is applicable to models where the new light bosons have lifetimes corresponding to flight distances within a few cm from the proton beamline before their decay. The recipe for application of the results to an arbitrary model with the same final state is provided. Interpretation of the results in the context of two benchmark models significantly surpasses the sensitivity of previous similar searches.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Demonstration of new PCSD capabilities

The new, more flexible and more friendly graphics capabilities to be available in later releases of the Pilot Climate Data System were demonstrated. The LIMS-LAMAT data set was chosen to illustrate these new capabilities. Pseudocolor and animation were used to represent the third and fourth dimensions, expanding the analytical capabilities available through the traditional two-dimensional x-y plot. In the new version, variables for the axes are chosen by scrolling through viable selections. This scrolling feature is a function of the new user interface customization. The new graphics are extremely user friendly and should free the scientist to look at data and converse with it, without doing any programming. The system is designed to rapidly plot any variable versus any other variable and animate by any variable. Any one plot in itself is not extraordinary; however, the fact that a user can generate the plots instead of a programmer distinguishes the graphics capabilities of the PCDS from other software packages. In addition, with the new CDF design, the system will become more generic, and the new graphics will become much more rigorous in the area of correlative studies.

Gough, M.↗

New Space Industries for the Next Millennium

New Space Industries For the Next Millennium is a final report of the findings from the New Space Industries Workshop held in Washington, DC, in February 1998. The primary purpose of this workshop was to identify what must be done to develop new markets, and to generate plans, milestones and new organizational relationships designed to facilitate the goal of space development. This document provides a summary report on the results of that workshop and is not intended as a statement of NASA or government policy. Previous studies had shown great potential for the development of new markets in space (e.g., travel and entertainment, space solar power, satellite and space transfer services, research and development in space, space manufacturing, and space resources), and a great need for coordination and formation of infrastructures (e.g., space transportation, space business parks, and space utilities), to facilitate the growth of new space businesses. The New Space Industries Workshop brought together government, academia, and industry participants from several previous studies and other professionals interested in the development of space for commercial purposes. Their participation provided input into the role of government and industry in space development as well as the technology needs that will enable space development. The opening of the frontier of space, not just to government missions but to private individuals and commercial business, is a challenge of overarching importance. It is our hope that the workshop and this final report continue in earnest the process of identifying and overcoming the barriers to large-scale public access and development of space in the early years of the next century.

Smitherman, D. V., Jr.↗

Operational Considerations when Designing New Ground Systems

The Hubble Space Telescope (HST) launched in April of 1991 with a nominal 15-year old mission. Since then, the HST mission life has been extended to 2010. As is true for all NASA missions, HST is being asked to decrease its operational costs for the remainder of its mission life. Various techniques are being incorporated for cost reductions, with one of the core means being the design of a new and more efficient ground system for HST operations. This new ground system, "Vision 2000", will reduce operational and maintenance costs and also provide the HST Project with added flexibility to react to future changes. Vision 2000 began supporting HST Operations in January of 1999 and will support the mission for the remainder of the mission life. Upgrading a satellite's ground system is a popular approach for reducing costs, but it is also inherently risky. Validating a new ground system can be a severe distraction to a flight team while operating a satellite. Mission data collection and health and safety requirements are rarely, if ever, relaxed during this validation period, forcing flight teams to undertake an additional task while operating the satellite. Additionally, flight teams must usually undergo extensive training to effectively utilize the new system. Once again, this training usually occurs as an additional task, in addition to the nominal satellite operations. While operating the spacecraft, the Flight Team typically assists in the design, validation, and verification of a new ground system. This is a distraction and strain on the Flight Team, but the benefit of using the Flight Team in all phases of ground system development far outweigh the negative aspects. Finally, above the cost of the new system, the integration into the facility with the current control center system are resources and costs not normally taken into account in the design phase of the new system. In addition to the standard issues faced by a Project when upgrading its ground system, the HST Project also must continue to support Space Shuttle servicing missions, which occur approximately every two to three years. This paper will address many of the issues common to all missions when re-hosting ground systems, and those faced by the HST Project in particular.

Walyus, Keith↗

Mission Control Technologies: A New Way of Designing and Evolving Mission Systems

Current mission operations systems are built as a collection of monolithic software applications. Each application serves the needs of a specific user base associated with a discipline or functional role. Built to accomplish specific tasks, each application embodies specialized functional knowledge and has its own data storage, data models, programmatic interfaces, user interfaces, and customized business logic. In effect, each application creates its own walled-off environment. While individual applications are sometimes reused across multiple missions, it is expensive and time consuming to maintain these systems, and both costly and risky to upgrade them in the light of new requirements or modify them for new purposes. It is even more expensive to achieve new integrated activities across a set of monolithic applications. These problems impact the lifecycle cost (especially design, development, testing, training, maintenance, and integration) of each new mission operations system. They also inhibit system innovation and evolution. This in turn hinders NASA's ability to adopt new operations paradigms, including increasingly automated space systems, such as autonomous rovers, autonomous onboard crew systems, and integrated control of human and robotic missions. Hence, in order to achieve NASA's vision affordably and reliably, we need to consider and mature new ways to build mission control systems that overcome the problems inherent in systems of monolithic applications. The keys to the solution are modularity and interoperability. Modularity will increase extensibility (evolution), reusability, and maintainability. Interoperability will enable composition of larger systems out of smaller parts, and enable the construction of new integrated activities that tie together, at a deep level, the capabilities of many of the components. Modularity and interoperability together contribute to flexibility. The Mission Control Technologies (MCT) Project, a collaboration of multiple NASA Centers, led by NASA Ames Research Center, is building a framework to enable software to be assembled from flexible collections of components and services.

Trimble, Jay↗

A Full-Scale Fire Program to Evaluate New Furnishings and Textile Materials Developed by the National Aeronautics and Space Administration

The plans for the present series of full-scale experimental fires were initiated at the suggestion of NASA following the presentation of a film and discussion illustrating Battelle-Columbus' recent work in fire research. That film showed bedroom-type fires carried out as a part of a program to determine the influence of the cyclic characteristics of real fires under limited ventilation on the burning and pyrolysis properties of the room furnishings. A new series of fires was suggested by NASA designed to show the performance of new fire resistant and fire retardant materials by providing comparative fire and smoldering environmental conditions. More recently, the goal for the new series of fires was written in a meeting with NASA personnel and others at Battelle on May 3 and 4, 1972. The goal was as follows: To establish the need for special materials of improved fire safety in domiciliary settings of public concern, and to assess, in a professionally acceptable manner, the potential of materials arising from the new space-age technology for this purpose. It was anticipated that some new materials arising from the space-age technology and not yet available through conventional commercial channels might provide significant improvements in fire safety if the best of the commercially available materials showed important shortcomings in this area. It was the intent of this program to assess the benefits that could accrue from the use of these new materials. Fire safety is a matter requiring the evaluation of a number of factors. For example, fire resistance and fire spread, visibility during the fire, toxicity of evolved gases, and the fire-fighting problem that is created must be evaluated before the relative hazard can be assessed. The plan of the program provided for sampling and instrumentation to evaluate these factors, consistent with the goal of technological utilization that has been specified. Arrangements were made with the Columbus Fire Department to use an existing six-story concrete building', designed and used as a fire training tower, as the site for the experimental fires. The visual evidence provided by TV and photographic coverage of the four experimental room fires showed clearly that the rooms responded very differently to a common ignition condition. In particular: (1) The Typical room, furnished from conventional retail sources, ignited easily and burned rapidly so that after 8 minutes the contents of the room were nearly destroyed. (2) The Improved room, furnished with materials selected as being among the best commercially available, showed substantial improvement over the Typical room in that there was slower fire spread. However, the relatively complete destruction of the room contents that resulted, and the large amounts of smoke, made it clear that substantial further improvements were needed. This fire was stopped after 29 minutes. (3) The Space-age room, furnished completely with new materials that were not yet commercially available, did not ignite under the common ignition condition and soon demonstrated the substantial improvement in fire resistance available for those components close to the ignition source. A second and larger ignition arrangement showed that this room can burn, but the difficulty with which this was brought about confirmed the improved fire resistance available with use of these materials. (4) The Mixed room ensemble, furnished with 'materials identical to the Typical room except for the substitution of the bed from the Space-age room, illustrated the improvement in control of fire spread available by careful placement of fire materials in the important paths of fire development of an otherwise ordinary room. The most significant hazards at early times in each fire were due to the rapid rise in heat flux and the abrupt obscuration of vision by smoke. The most consistent toxicity hazard was due to CO and its importance would depend on the ability of the occupant to survive the initial heat and smoke menace which characterized each fire room. Other gases and vapors were shown to reach hazardous levels in certain fire rooms and, again, their significance to an occupant, would relate to the times in which such hazards occurred, and probably to the synergistic nature of the hazard arising from mixtures of such gases. Fire retardant items in the room are caused to pyrolyze by the heat of burning from other items in the room and so contribute to combustible and toxic vapor accumulations, even though they may not have entered into the burning process. This effect of a mixture of combustible materials to produce burning and pyrolysis not characteristic of any one item individually we have chosen to call the "ensemble effect". Further full-scale fire trials may be expected to show the significant changes that control the burning and pyrolytic processes and in that event a programmed fire chamber should be developed to yield realistic laboratory results.

Hillenbrand, L. J.↗

A New Formulation of Time Domain Boundary Integral Equation for Acoustic Wave Scattering in the Presence of a Uniform Mean Flow

It has been well-known that under the assumption of a constant uniform mean flow, the acoustic wave propagation equation can be formulated as a boundary integral equation, in both the time domain and the frequency domain. Compared with solving partial differential equations, numerical methods based on the boundary integral equation have the advantage of a reduced spatial dimension and, hence, requiring only a surface mesh. However, the constant uniform mean flow assumption, while convenient for formulating the integral equation, does not satisfy the solid wall boundary condition wherever the body surface is not aligned with the uniform mean flow. In this paper, we argue that the proper boundary condition for the acoustic wave should not have its normal velocity be zero everywhere on the solid surfaces, as has been applied in the literature. A careful study of the acoustic energy conservation equation is presented that shows such a boundary condition in fact leads to erroneous source or sink points on solid surfaces not aligned with the mean flow. A new solid wall boundary condition is proposed that conserves the acoustic energy and a new time domain boundary integral equation is derived. In addition to conserving the acoustic energy, another significant advantage of the new equation is that it is considerably simpler than previous formulations. In particular, tangential derivatives of the solution on the solid surfaces are no longer needed in the new formulation, which greatly simplifies numerical implementation. Furthermore, stabilization of the new integral equation by Burton-Miller type reformulation is presented. The stability of the new formulation is studied theoretically as well as numerically by an eigenvalue analysis. Numerical solutions are also presented that demonstrate the stability of the new formulation.

Hu, Fang↗

New York City Panel on Climate Change 2019 Report Chapter 1: Introduction

While urban areas like New York City and its surrounding metropolitan region are key drivers of climate change through emissions of greenhouse gases, cities are also significantly impacted by climate shifts, both chronic changes and extreme events. These are already affecting the New York metropolitan region, including the five boroughs of New York City through higher temperatures, more intense precipitation, and higher sea levels, and will increasingly do so in the coming decades. The City of New York has embarked on a flexible adaptation pathway (i.e., strategies that can evolve through time as climate risk assessment, evaluation of adaptation strategies, and monitoring continues) to respond to climate change challenges. This entails significant programs to develop resilience in communities and critical infrastructure to observed and projected changes in temperature, precipitation, and sea level. The first NPCC Report laid out the risk management framing for the city and region via flexible adaptation pathways. The second New York City Panel on Climate Change Report (NPCC2) developed the “climate projections of record” that are currently being used by the City of New York in its resilience programs . The NPCC3 2019 Report co-generates new tools and methods for the next generation of climate risk assessments and implementation of region-wide resilience. Co-generation is an interactive process by which stakeholders and scientists work together to produce climate change information that is targeted to decision-making needs. These tools and methods can be used to observe, project, and map climate extremes; monitor risks and responses; and engage with communities to develop effective programs. They are especially important at “transformation points” in the adaptation process when large changes in the structure and function of physical, ecological, and social systems of the city and region are undertaken.

Rosenzweig, Cynthia↗

New York City Panel on Climate Change 2019 Report Chapter 9: Perspectives on a City in a Changing Climate 2008-2018

Cities experience multiple environmental shifts, stresses, and shocks—such as air and water pollution—and a variety of extreme events simultaneously and continuously. Current urban programs have focused on limiting the impacts of these conditions through a portfolio of multifaceted strategies, such as regulations and codes, management and restoration projects, and citizen engagement. Global climate change represents a new environmental dynamic to which cities now have to respond. While global climate change by definition has impacts world wide, residents and managers of cities, like New York, typically perceive changes in their own local environments. In most cities, temperature is warming with increasingly hotter and longer heatwaves, and heavier downpours are leading to more frequent inland flooding. In coastal cities, sea levels are rising, exacerbating coastal flooding. Analyzing and understanding the impacts of climate change on cities is important because of the dramatic growth in urban populations throughout the world. An estimated nearly 4.0 billion people reside in urban areas, accounting for 52% of the world’s population (UN, 2017). That percentage will increase dramatically in the coming decades as almost all of the growth to take place up to 2050 will be in urban areas (UN, 2017). The New York City metropolitan region (NYMR)—the five boroughs (equivalent to counties) of New York City and the adjacent 26 counties in the states of New York, New Jersey, and Connecticut—is an ideal model of an urban agglomeration. Approximately 8.6 million people live in the five boroughs and more than 15 million people live in the neighboring smaller cities, towns, and villages (City of New York, 2018a; US Census, 2017). The population of the five boroughs is projected to add 1 million people by 2030, while the total region is projected to reach 26.1 million (NYTC, 2015).

Solecki, William↗

The New Landsat Collection-2 Digital Elevation Model

The Landsat Collection-2 distribution introduces a new global Digital Elevation Model (DEM) for scene orthorectification. The new global DEM is a composite of the latest and most accurate freely available DEM sources and will include reprocessed Shuttle Radar Topographic Mission (SRTM) data (called NASADEM), high-resolution stereo optical data (ArcticDEM), a new National Elevation Dataset(NED) and various publicly available national datasets including the Canadian Digital Elevation Model (CDEM) and DEMs for Sweden, Norway and Finland (SNF). The new DEM will be available world-wide with few exceptions. It is anticipated that the transition from theCollection-1 DEM at 3 arcsecond to the new DEM will be seamless because processing methods to maintain a seamless transition were employed, void filling techniques were used, where persistent gaps were found, and the pixel spacing is the same between the two collections. Improvements to the vertical accuracy were realized by differencing accuracies of other elevation datasets to the new DEM. The greatest improvement occurred where ArcticDEM data were used, where an improvement of 35 meters was measured. By using theses improved vertical values in a line of sight algorithm, horizonta improvements were noted in some of the most mountainous regions over multiple 30-meter Landsat pixels. This new DEM will be used to process all of the scenes from Landsat 1-8 in Collection-2 processing and will be made available to the public by the end of 2020.

Shannon Franks↗

Solar Power System and Radioisotope Thermoelectric Generation Technologies at Jupiter-Saturn-Uranus Environments: New Insights and Paradigms

Power system selection for outer planet destinations, such as Jupiter, Saturn, and Uranus and beyond, is complex, involving and dependent on many interdisciplinary factors such as power system mass, specific power, cost, mechanical and electrical integration, and natural radiation environment. Low solar irradiance at Jupiter, Saturn, and Uranus systems (i.e., 50, 15, and 4 W/m2 , respectively) makes solar power systems challenging in mechanical / electrical integration and accommodating radiation environments. More costly radioisotope thermoelectric generator (RTG) systems can help proposed missions overcome radiation environment and spacecraft control challenges at Jupiter, Saturn, and Uranus. NASA’s Jet Propulsion Laboratory (JPL) has recently made significant strides in demonstrating high-efficiency, radiation-hard solar cell technologies for low-irradiance, low-temperature (LILT) applications, and high-efficiency thermoelectric (TE) materials and modules for higher-specific-power RTGs. Stateof-art multi-junction solar cells now routinely demonstrate high efficiencies of 30-34% at LILT (9.5AU and -165°C), making solar arrays a viable option for many near-term Saturn mission concepts. Emerging technologies like LILToptimized solar cells have recently demonstrated even higher efficiencies of 37% at 9.5AU and -165°C and 30% lower mass than the state-of-art, offering the prospect of ~3W/kg array-level, end-of-life specific powers under Saturn conditions. Having already demonstrated the tremendous utility of RTGs on Mars and in deep-space missions (e.g., Galileo at Jupiter, New Horizons at Pluto), NASA is now developing and demonstrating new TE materials and modules (e.g., skutterudites, La3-x Te4, and Zintls) for increasing RTG specific power (up to >8.5 W/kg), which strongly impacts an RTG’s mass, fuel utilization, and modularity in the power system trade domain. New accomplishments in both areas highlight the renewed requisite for updated comparisons and trade-offs in power output, specific power and mass, cost, mechanical and electrical integration, new technology timelines, and natural radiation impacts between new LILT-optimized photovoltaic technologies and next-generation RTG technologies. This work discusses and demonstrates how new LILT-based technologies are now allowing one to consider and design solar power systems for Saturn orbit and beyond, and are changing the potential cost-mass trade-offs between emerging solar power technologies and newly-envisioned RTG technologies. Key updated system mass and cost trade-offs between high-performance LILT solar technologies and new RTG technologies are presented, reinforcing and refining power selection criteria supporting possible future NASA deep-space science and exploration missions to Mars, the Jupiter system (Europa, Ganymede), the Saturn system (Titan, Enceladus), Uranus, and beyond. Key trade-offs in other above-mentioned interdisciplinary factors between these two power technologies are also discussed.

Bairstow, Brian K.↗

UPGRADING THE CEBAF INJECTOR WITH A NEW BOOSTER, HIGHER VOLTAGE GUN, AND HIGHER FINAL ENERGY

The Continuous Electron Beam Accelerator Facility (CEBAF) accelerator at Jefferson Lab will be upgraded from 6 GeV to 12 GeV in the next few years. To meet the requirement of the new machine and to take the opportunity to improve the beam quality, the CEBAF injector will be upgraded with a higher voltage gun, a new booster, and a new accelerating RF module. The CEBAF injector creates and accelerates three beams at different currents simultaneously. The beams are interleaved, each at one third of the RF frequency, traveling through the same beam line. The higher voltage gun will lower the space charge effects. The new booster with optimized beam dynamics will complete the bunching process and provide initial acceleration matched to the new gun voltage. Using our latest SRF design, the new booster has significantly lower x/y coupling effects that should improve our beam setup and operation for the highly sensitive parity experiments scheduled for the CEBAF's future. Finally, the new accelerating RF module will roughly double the injector final energy to match the rest of the 12 GeV accelerator. In this paper we will provide more detail about this upgrade.

43 PARTICLE ACCELERATORS↗

Airport Analyses Informing New Mobility Shifts: Opportunities to Adapt Energy-Efficient Mobility Services and Infrastructure: Preprint

An airport is one of the most important assets for a region's economic development and connectivity with the rest of the nation and world. Key aspects for investigation of energy efficient mobility at airports is ground transportation including factors ranging from the infrastructure, mobility services, and associated revenues. Data is critical to understand the maturity of new mobility services that can inform both cities and airports on how to respond, approach, manage, and adapt to the challenges, opportunities, and uncertainties associated with shifts in new mobility that influence human behavior, energy-efficiency and sustainability strategies. One key question identified in this article is how quickly we are adapting to new mobility options - such as app-based ride-hailing and 'pooling' services - that may provide an opportunity to influence energy efficiency of ground transportation to and from airports. By starting with airports in the regions of four smart city finalists in the U.S. DOT Smart City Challenge, this paper focuses on key observability aspects of new modes and the rate of shifts in mobility patterns across San Francisco, Portland, Denver, and Kansas City. With the emerging megatrend of rising urbanization and rising air travel demand (a predicted doubling in demand by 2035), airports are expected to increasingly be on the front lines of adaptation to new transportation technology and services in terms of infrastructure investments, policies, and revenues. As airports have demonstrated the most potential and capability of any public institution to implement fees for new ride-hailing services, they are also a prime resource for collecting important data to help understand smart mobility transitions. Results focused on the shifts in revenues for ground transportation at airports offer one vantage point into the pace of transitions and adaptations in the new emerging mobility landscape, and present an opportunity to analyze how future adaptations could support more energy-efficient scenarios.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Status of a New Resonance Evaluation for Cerium to Support Nuclear Criticality Safety Applications

A new resonance evaluation is currently being carried out at Oak Ridge National Laboratory (ORNL) for isotopes of cerium. This new evaluation will provide a much-needed update of the resolved and unresolved resonance parameters for {sup 140}Ce and {sup 142}Ce based on new and existing experimental cross section data. The physics of the resolved resonance region will be greatly improved, and new resonance parameter covariance data will be generated. Cerium exists predominately as {sup 140}Ce and {sup 142}Ce and can be found in chemical processing streams because it is used commercially as a catalyst or additive in chemical applications (e.g., glass polishing powder). Cerium has neutron-absorbing properties that can influence the reactivity of systems with fissionable material. The need for improved cerium cross section data has been identified specifically for the Hanford Plutonium Finishing Plant as part of the Nuclear Criticality Safety Program (NCSP) nuclear data request. Furthermore, cerium is a high-yield fission product, making it relevant for reactor calculations. Currently, ENDF/B-VII.1 evaluations for cerium isotopes (described in Section II) do not include the covariance data needed to support sensitivity/uncertainty analyses of systems involving cerium. In addition, the available cerium resonance parameters in ENDF/B-VII.1 are based on parameters provided in the Atlas of Neutron Resonances: Resonance Parameters and Thermal Cross- Sections. Z = 1-100 by S. Mughabghab; hence, the 'evaluated' resonance parameters are not based on a detailed R-matrix analysis. Furthermore, differential measurements are needed in the resonance region to accurately predict the neutron resonances. ORNL has completed new differential measurements on natural samples of cerium, and measurements of an enriched {sup 142}Ce sample are planned. A corresponding resonance evaluation for {sup 140}Ce and {sup 142}Ce being conducted by ORNL will provide detailed cross section resonance parameters and corresponding evaluated covariance data in the resonance region in support of the NCSP. The target uncertainty requested by the NCSP is on the order of 1-2% for the total cross section and less than 6% for the capture cross section in the resolved resonance region. New cerium resonance evaluations will significantly improve radiation transport calculations for systems involving cerium in processes in the DOE Complex. Also, the new evaluations will provide much-needed evaluated covariance data to support sensitivity/ uncertainty analyses.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗