Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “minimum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al{sub 2}O{sub 3}-TiN and MgAl{sub 2}O{sub 4}-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl{sub 2}O{sub 4}-TiN interface rather than that of Al{sub 2}O{sub 3}-TiN interface. When ∆T{sub TiN} (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

36 MATERIALS SCIENCE↗

Modified DHTT Equipment for Crystallization Studies of Mold Slags

The double hot thermocouple technique (DHTT) enables simulations of the temperature gradient at near-service conditions during continuous casting of steel. With the equipment applied so far, a rectangular slag film of even thickness often cannot be achieved. Further, the minimum temperature frequently lies within the slag film. Modified equipment can avoid these disadvantages via the following design features. The entire furnace chamber is heated to the selected temperature of the cold wire, and the minimum temperature is not located within the slag film. Furthermore, the shape of the heating wire is improved, which enables mounting of a thin, rectangular slag film between four platinum wires. This modification allows for investigations on transparent and translucent slags. So far, the results from DHTT investigations were represented via snapshots of the samples at certain experimental times. Therefore, appropriate methods for the graphical representation of the results were suggested: the maximum crystallinity, the time related to certain crystallinities with a dependence on the position within the slag film, and the crystal growth rate. The CaO-MgO-Al{sub 2}O{sub 3}-SiO{sub 2} slag investigated with this equipment was mineralogically examined additionally, and based on thermodynamic calculations, the allocation of temperatures to certain positions within the crystallized slag film was possible.

36 MATERIALS SCIENCE↗

Optimized Electromagnetic Fields Levitate Bulk Metallic Materials

The bulk metallic electromagnetic levitation technique has a promising application prospect in condensed physics and materials science. In order to resolve the problem of weak levitation force and the small size of samples, an optimized solution based on finite element analysis (FEA) is developed to seek the best electromagnetic field distribution in the levitation zone. The influence of material properties on the distribution of magnetic flux density, surface pressure, and the Lorentz force were studied by the FEA method with various sample sizes of titanium and copper balls. The levitation capability of cylindrical coil system which consists of a single-layer coil with an inner diameter of 30 mm and the levitated object with a diameter of 20 mm was analyzed. To keep a balance between the turn number and increment efficiency of force, the best number of 7 turns is confirmed. Then, two types of optimized coils were predicted by numerical simulations, and the levitation force is improved drastically. The double-layer coil displays an outstanding levitation capability owing to the strong electromagnetic field generated by multilayer turns. In addition, 5 to 50 g aluminum, titanium, copper, and nickel are levitated by the above three kinds of coils and the levitation capacities are validated from the recorded data of the minimum operating current that can levitate the samples. The experimental results show good agreements with the simulation results, and the minimum current for optimized coils is reduced efficiently.

36 MATERIALS SCIENCE↗

The Dissolution of Fe in HCl from the Ilmenite Concentrate; Evaluating the Effect of Operating Parameters and Mutual Interactions

Selective HCl dissolution of ilmenite components for obtaining Ti or titanium dioxide (TiO{sub 2}) has been highly recognized due to its advantages, greater environmental friendliness, and simplicity, compared to H{sub 2}SO{sub 4} and Cl{sub 2} methods. The effect of numerous parameters has been studied with the one-factor-at-a-time method. The present study aimed to evaluate the effect of key operation parameters, such as acid-to-solid ratio (A/S: 5 to 20 mL/g), reaction temperature (T: 70 °C to 100 °C), and acid concentration (A pct: 15 to 30 wt pct), on the dissolution of Fe in HCl solution with the minimum Ti losses to the leachate from its abundant, domestic, and low-cost mineral source (Kahnooj ilmenite concentrate) using central composite design–response surface methodology. After 90 minutes of leaching, the Ti/Fe (pct) in terms of dissolved amounts was selected as the process assessment response function. Based on the conducted experimental and statistical analysis, increasing the levels of parameters in the studied domain leads to an increase in Ti/Fe (pct), in the order of A pct > T > A/S. Two statistically significant mutual interactions between A/S-T and T-A pct, with 95 pct confidence level, were revealed for the first time in this study. The optimization strategy was set to the minimization of Ti/Fe (pct) by considering the objective of study and the selected response function. The A/S, T, and A pct were determined to be 5 mL/g, 70 °C, and 15 pct, respectively, for maximum impurity dissolution and minimum Ti loss to the leachate.

36 MATERIALS SCIENCE↗

An improved Armstrong–Frederick-Type Plasticity Model for Stable Cyclic Stress–Strain Responses Considering Nonproportional Hardening

This paper modified an Armstrong–Frederick-type plasticity model for investigating the stable cyclic deformation behavior of metallic materials with different sensitivity to nonproportional loadings. In the modified model, the nonproportionality factor and nonproportional cyclic hardening coefficient coupled with the Jiang–Sehitoglu incremental plasticity model were used to estimate the stable stress–strain responses of the two materials (1045HR steel and 304 stainless steel) under various tension–torsion strain paths. A new equation was proposed to calculate the nonproportionality factor on the basis of the minimum normal strain range. Procedures to determine the minimum normal strain range were presented for general multiaxial loadings. Then, the modified model requires only the cyclic strain hardening exponent and cyclic strength coefficient to determine the material constants. It is convenient for predicting the stable stress–strain responses of materials in engineering application. Comparisons showed that the modified model can reflect the effect of nonproportional cyclic hardening well.

36 MATERIALS SCIENCE↗

A Simplified Procedure to Determine Post-necking True Stress–Strain Curve from Uniaxial Tensile Test of Round Metallic Specimen Using DIC

Triaxial state of stress is usually generated in the necked zone because of neck geometry, and as a consequence proper correction of true tensile stress–strain curve after necking is mandatory. Various correction factors like Bridgman, Davidenkov and Spiridonova, Siebel and Schwaigere are available in the published literature to calculate true stress from mean axial stress. Similarly true strains can be calculated from the minimum diameters of the round specimen in the necked region for various true stress levels. But experimental determination of correction factors and minimum diameters of the round specimen in the necked region is a cumbersome task. This investigation shows a simplified procedure to determine true strains and the correction factors from digital image correlation-based local strain measurement in the necked region. The present procedure is validated by experimental results of rail steel.

36 MATERIALS SCIENCE↗

Nonlinear Resonance Response of Porous Beam-Type Implants Corresponding to Various Morphology Shapes for Bone Tissue Engineering Applications

Having excellent biocompatibility and apatite mineralization as well as efficient mechanical properties makes bredigite as one of the most attractive bioceramics. A beam-type porous biological implant in a 3D-printed architecture is designed with micron pore size. The surface properties, morphology, and size of the composed powders are evaluated using Scherrer and Williamson-Hall equation. The effect of MNPs deposition into the bredigite bioceramics and correlation with temperature effect on roughness of the prepared bio-nanocomposite are also investigated for hyperthermia application potential. The composed powders are characterized by x-ray diffraction, and then scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis (weight change, TGA), and atomic force microscopy are utilized to evaluate the surface topography. The resonance response is the tendency of a bone scaffold to respond at prominent amplitude while the frequency of its oscillations is equal to the structure’s natural frequency of vibration. Therefore, based on the obtained mechanical properties via the experimental approach for the bio-nanocomposite material, an analytical solution based upon the multiple-timescale method is carried out to analyze the nonlinear primary resonance of a 3D-printed porous beam-type biological implant under uniform-distributed load. According to SEM observations, there are hard agglomerates in the bredigite-magnetite nanoparticles (Br-MNPs) bio-nanocomposite material with low weight fraction of MNPs. However, they are broken down by increasing the amount of MNPs. Also, it is displayed that for lower MNPs weight fraction, the height of jump phenomenon related to the nonlinear resonance response is maximum and minimum for, respectively, irregular and mesoporous shapes of morphology, but their associated forcing amplitudes related to the bifurcation points are minimum and maximum, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Long-Term Creep Behavior of a CoCrFeNi Medium-Entropy Alloy

We report that current research shows that high-entropy alloys (HEAs) can offer superior oxidation resistance compared to more traditional austenitic stainless steels with equivalent tensile mechanical performance. While many reports have been published on creep of CoCrFeNiMn, few focus on the CoCrFeNi family of low to medium entropy alloys. In this manuscript, uniaxial tensile creep test results for more than 46,000 accumulated hours are presented on the equiatomic CoCrFeNi alloy. The alloy was manufactured at NETL using a vacuum induction melt solidification approach with a computationally designed homogenization cycle. After completing the homogenization cycle, the ingot was first hot forged and then hot rolled into 10 mm thick plate, a product form that is relevant to many industries. Creep tests were performed in the temperature range of 600-650 °C using applied stresses from 120 to 189 MPa. This study builds upon previous results on the CoCrFeNiMn family of high-entropy alloys and offers a modicum of clarification about performance compared to small button melts by using ASTM standard test procedures and mechanical test specimens. The apparent creep activation energy and creep stress exponent were similar to those for CoCrFe medium-entropy and CoCrFeNiMn high-entropy alloys. The post-test creep microstructure showed some Cr segregation, which has also been noted for other CoCrFe alloys. The CoCrFeNi alloy also presents a double minimum or two minimum creep rate phenomena.

36 MATERIALS SCIENCE↗

Relationship between Grain Size and Sample Thickness on the Creep-Rupture Performance of Thin Metallic Sheets of INCONEL Alloy 740H

A study was conducted on INCONEL® alloy 740H® to examine the role of grain size and sheet thickness on the alloy’s creep-rupture behavior. Three different starting sheet thicknesses were utilized and multiple heat-treatment conditions anticipated for compact heat exchanger (CHX) manufacturing were applied to produce a range of grain sizes. Creep-rupture testing was conducted at 750 °C for times up to about 6000 h and the results were compared to wrought databases. The data show that both creep strength and ductility were important factors in the overall creep performance of the sheets. Reductions in performance were observed due either to accelerated creep when grain size was fine or loss of rupture ductility when grain sizes approached the sheet thickness. Some combinations of heat-treatment and thickness were able to produce typical expected wrought creep properties. Historically a ‘rule-of-thumb’ requirement for creep testing suggests 3-5 grains per sample minimum dimension to ensure homogeneous behavior. This research shows that to ensure representative wrought creep performance (i.e. no effect of sample size), the sample minimum cross-section should be 10 times the average ASTM grain size. Statistical analysis of the microstructures suggests the population of larger grains as a controlling feature in creep failure.

14 SOLAR ENERGY↗

Optimizing biomass feedstock blends with respect to cost, supply, and quality for catalyzed and uncatalyzed fast pyrolysis applications

Here, biomass cost, quality and quantity are important parameters to consider when choosing feedstocks and locations for biorefineries. Biomass cost is dependent upon type, location, quantities available in a given area and logistics costs as well the quality needed for the biorefinery. Biomass quality depends upon type, growth conditions, weather, harvesting methods, storage conditions as well as any preprocessing methods used to improve quality. Biomass quantity depends heavily on location as well as growth conditions, weather, harvesting methods and storage conditions. This study examines how all three of these parameters affect the biomass mixture that is needed in a biomass depot or biorefinery to achieve the lowest cost with the highest quality and at the quantities needed for biorefinery operation. Four biomass depots were proposed in South Carolina that would each process the predominant type of biomass available in that area and each produce 200,000 tons of feedstock per year. These depots would then feed a centrally located 800,000 ton biorefinery that would convert the feedstocks to pyrolysis oil using either catalyzed or uncatalyzed fast pyrolysis. The four depots each needed to produce different blends of biomass based upon the quantities available to them but still meet the minimum quality requirements for the biorefinery. Costs were minimized by using waste biomass resources such as construction and demolition waste, logging residues and forest residuals. Depending upon the quality specification required by the biorefinery, it was necessary to utilize preprocessing methods such as air classification and acid leaching to upgrade biomass quality. In the case of uncatalyzed fast pyrolysis, all four depots could produce biomass blends that were lower cost than the the preferred pyrolysis feedstock, clean pine, and meet quality and quantity specifications. For catalyzed fast pyrolysis, three of the four depots were able to produce blends that met both quality and quantity specifications at minimum cost. The fourth depot would not be able to produce a blend meeting specifications without increasing the supply radius for the depot.

09 BIOMASS FUELS↗

Techno-Economic Evaluation of Cellulosic Ethanol Production Based on Pilot Biorefinery Data: a Case Study of Sweet Sorghum Bagasse Processed via L+SScF

Replacing fossil fuels with renewable fuels derived from lignocellulosic biomass can contribute to the mitigation of global warming and the economic development of rural communities. This will require lignocellulosic biofuels to become price competitive with fossil fuels. Techno-economic analyses can provide insights into which parts of the biofuel production process need to be optimized to reduce cost or energy use. Here, we used data obtained from a pilot biorefinery to model a commercial-scale biorefinery that processes lignocellulosic biomass to ethanol, with a focus on the minimum ethanol selling price (MESP). The process utilizes a phosphoric acid-catalyzed pre-treatment of sweet sorghum bagasse followed by liquefaction and simultaneous saccharification and co-fermentation (L+SScF) of hexose and pentose sugars by an engineered Escherichia coli strain. After validating a techno-economic model developed with the SuperPro Designer software for the conversion of sugarcane bagasse to ethanol by comparing it to a published Aspen Plus model, six different scenarios were modeled for sweet sorghum bagasse Under the most optimistic scenario, the ethanol can be produced at a cost close to the energy-equivalent price of gasoline. Aside from an increase in the price of gasoline, the gap between ethanol and gasoline prices could also be bridged by either a decrease in the cost of cellulolytic enzymes or development of value-added products from lignin.

Biofuel↗

Asynchronously parallel optimization solver for finding multiple minima

This paper proposes and analyzes an asynchronously parallel optimization algorithm for finding multiple, high-quality minima of nonlinear optimization problems. Our multistart algorithm considers all previously evaluated points when determining where to start or continue a local optimization run. Theoretical results show that, under certain assumptions, the algorithm almost surely starts a finite number of local optimization runs and identifies, or has a single local optimization run converging to, every minimum. The algorithm is applicable to general optimization settings, but our numerical results focus on the case when derivatives are unavailable. In numerical tests, a PYTHON implementation of the algorithm is shown to yield good approximations of many minima (including a global minimum), and this ability scales well with additional resources. Our implementation’s time to solution is shown also to scale well even when the time to evaluate the function evaluation is highly variable.

97 MATHEMATICS AND COMPUTING↗

Bounds for the l{sub 1}-distance of q-ary lattices obtained via Constructions D, D{sup ′} and ( D )-bar

Lattices have been used in several problems in coding theory and cryptography. In this paper, we approach q-ary lattices obtained via Constructions D, D {sup ′} and ( D )-bar . It is shown connections between Constructions D and D {sup ′}. Bounds for the minimum l{sub 1}-distance of lattices Λ{sub D}, Λ{sub D{sup ′}} and Λ{sub D̄} and, under certain conditions, a generator matrix for Λ{sub D{sup ′}} are presented. In addition, when the chain of codes used is closed under the zero-one addition, we derive explicit expressions for the minimum l{sub 1}-distances of the lattices Λ{sub D} and Λ{sub D̄} attached to the distances of the codes used in these constructions.

97 MATHEMATICS AND COMPUTING↗

Optimization of collision-free paths in a differential-drive robot by a smoothing piecewise-linear approach

This paper presents a methodology for optimizing pre-calculated collision-free paths of differential-drive wheeled robots. The main advantage of this methodology is that optimization is done by considering the kinematics and mechanical constraints of the mobile robot. In accordance to this proposal, the optimized path is achieved by applying recursively a local smoothing on an initial path which is originally modeled as a one-dimensional piecewise linear function. By this recursive smoothing, it can be ensured that the original piecewise linear function can be transformed into a smooth one that fulfill the constraints established by the kinematic equations of the wheeled mobile in terms of a minimum radius of curvature. As a result of this, a trajectory which guarantees lower power consumption and lower mechanical wear, is obtained. To show the better performance of the proposed approach, numerical simulation results are contrasted to those obtained from other reported methods with regards to path length, minimum radius of curvature, cross track error, continuity and resulting acceleration.

97 MATHEMATICS AND COMPUTING↗

Cultivating clarity: understanding the impact of land cost assumptions on biofuel viability

The transition to sustainable energy has increased interest in biofuel production to reduce greenhouse gas emissions, decrease reliance on imported oil, and ensure energy resilience. Here, this study examines the often-overlooked impact of land cost assumptions on the economic viability of biofuel production. Using a discounted cash flow techno-economic framework, we evaluated three land cost scenarios—no land costs, land rental costs, and land purchase costs—across six bioenergy feedstocks (corn, soybeans, switchgrass, miscanthus, poplar, and microalgae) and three biofuel products (corn ethanol, soybean biodiesel, and sustainable aviation fuel) at the county level for the contiguous United States. The analysis reveals substantial variation in minimum fuel selling prices due to these scenarios. High-yield crops like algae showed low sensitivity to land costs, while low-yield crops such as soybeans were highly sensitive. Geographical differences were significant, with minimum fuel selling price increases most pronounced in high-value land regions like the Corn Belt. Case studies further illustrate the influence of local productivity and land costs on economic outcomes across the United States. These findings emphasize the importance of maintaining consistent land cost assumptions in biofuel economic assessments. By quantifying the interplay between land value, crop productivity, and economic feasibility, this study provides essential insights for policymakers and stakeholders to advance sustainable energy solutions.

09 BIOMASS FUELS↗

The maximum relaxation time of a random walk

In this paper, we show the minimum spectral gap of the normalized Laplacian over all simple, connected graphs on n vertices is ( 1 + o ( 1 ) ) 54 n 3 . This minimum is achieved asymptotically by a double kite graph. Consequently, this leads to sharp upper bounds for the maximum relaxation time of a random walk, settling a conjecture of Aldous and Fill. We also improve an eigenvalue–diameter inequality by giving a new lower bound for the spectral gap of the normalized Laplacian. Finally, this eigenvalue lower bound is asymptotically best possible.

97 MATHEMATICS AND COMPUTING↗

On the measurement of dislocations and dislocation substructures using EBSD and HRSD techniques

The accumulation of the dislocations and development of dislocation structures in plastically deformed Ni201 is examined using dedicated analyses of Electron Back-Scatter Diffraction (EBSD) acquired orientation maps, and High-Resolution Synchrotron Diffraction (HRSD) acquired patterns. The results show that the minimum detectable microstructure-averaged (bulk) total dislocation density ($ρ_T$) measured via HRSD is approximately 1E13 m -2 , while the minimum GND density ($ρ_G$) measured via EBSD is approximately 2E12 m -2 - the EBSD technique being more sensitive at low plastic strain. This highlights complementarity of the two techniques when attempting to quantify amount of plastic deformation (damage) in a material via a measurement of present dislocations and their structures. Furthermore, a relationship between EBSD-measured $ρ_G$ and the size of HRSD-measured Coherently Scattering Domains (CSDs) has been mathematically derived - this allows for an estimation of the size of CSDs from EBSD-acquired orientation maps, and conversely an estimation of $ρ_G$ from HRSD-measured size of CSDs. The measured evolution of ($ρ_T$), and $ρ_G$ is compared with plasticity theory models - the current results suggest that Ashby's single-slip model underestimates the amount of ONDs ($ρ_G$), while Taylor's model is correctly predicting the total amount of dislocation ($ρ_T$) present in the material as a function of imparted plastic strain.

36 MATERIALS SCIENCE↗

Divergent responses of spring phenology to daytime and nighttime warming

Spring phenology (i.e., start of season, SOS) has shifted earlier in response to warmer temperatures. However, the respective influences of daytime and nighttime temperatures on SOS changes remain poorly understood. Here we characterized the responses of satellite-derived SOS to minimum temperature (Tmin) and maximum temperature (Tmax) across Appalachian Trail regions in the Eastern United States during 2000-2013. We found SOS responded differently to Tmin and Tmax at 81.5% of the study area. Furthermore, the SOS responses to Tmin and Tmax both changed across space, and specifically, these two responses showed significant divergent trends from cold to warm regions (P<0.001). We propose a new framework utilizing both Tmin and Tmax, instead of daily average temperature, in modeling phenology. This study, for the first time, disentangled phenological responses to daytime temperature from nighttime temperature across a wide range of temperatures. The findings suggest that model projections of future phenological changes should incorporate the divergent phenology responses to daytime and nighttime temperatures, in order to improve the representation of land-atmosphere interactions in Earth system models in light of asymmetric diurnal warming.

asymmetric warming, temperature sensitivity, Appal↗