Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “inlet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Oblique inlet pressure loss for swirling flow entering a catalyst substrate

This experimental study investigates the oblique inlet pressure loss for the entry of an annular swirling flow into an automotive catalyst substrate. The results are applicable to a wide range of compact heat exchangers. For zero swirl, the total pressure loss agrees with established expressions for pressure loss in developing laminar flow in parallel channels with finite wall thickness. For positive swirl, the additional pressure loss due to oblique flow entry is correlated to the tangential velocity upstream of the catalyst, measured using laser-Doppler anemometry. The obtained oblique inlet pressure loss correlation can improve the accuracy of numerical calculations of the flow distribution in catalysts. (author)

33 ADVANCED PROPULSION SYSTEMS↗

High-Fidelity Simulations of a Linear HPT Vane Cascade Subject to Varying Inlet Turbulence

The effect of inflow turbulence intensity and turbulence length scales have been studied for a linear high-pressure turbine vane cascade at Reis = 590,000 and Mis = 0.93, using highly resolved compressible large-eddy simulations employing the WALE turbulence model. The turbulence intensity was varied between 6% and 20% while values of the turbulence length scales were prescribed between 5% and 20% of axial chord. The analysis focused on characterizing the inlet turbulence and quantifying the effect of the inlet turbulence variations on the vane boundary layers, in particular on the heat flux to the blade. The transition location on the suction side of the vane was found to be highly sensitive to both turbulence intensity and length scale, with the case with turbulence intensity 20% and 20% length scale showing by far the earliest onset of transition and much higher levels of heat flux over the entire vane. It was also found that the transition process was highly intermittent and local, with spanwise parts of the suction side surface of the vane remaining laminar all the way to the trailing edge even for high turbulence intensity cases.

Pichler, Richard↗

AmeriFlux FLUXNET-1F US-HB1 North Inlet Crab Haul Creek

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site US-HB1 North Inlet Crab Haul Creek. This is the FLUXNET version of the carbon flux data for the site US-HB1 North Inlet Crab Haul Creek produced by applying the standard ONEFlux (1F) software. Site Description - The flux footprint includes a tidal salt marsh with approximately 40% tall form Spartina alterniflora, 40% short form Spartina alterniflora and 20% creek.

Schermaier, Daniel↗

AmeriFlux FLUXNET-1F CA-Mtk Mittimatalik (Pond Inlet) Tundra

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site CA-Mtk Mittimatalik (Pond Inlet) Tundra. This is the FLUXNET version of the carbon flux data for the site CA-Mtk Mittimatalik (Pond Inlet) Tundra produced by applying the standard ONEFlux (1F) software. Site Description - Mesic to dry tundra with dwarf shrubs, grasses, forbs, and moss vegitation. Thin organic soil layer of 10 cm with sandy soils.

Arndt, Kyle [Woodwell Climate Research Center]↗

Characterization of Inlet Guide Vane Performance for Discharge Compressor Operation near the Dome of an sCO 2 Pumped Heat Energy Storage

Southwest Research Institute® (SwRI®) developed and tested a Variable Inlet Guide Vane (IGV herein) assembly on an integrally-geared sCO 2 compressor (IGC) to demonstrate compressor operation at both the compressor design point and near the dome and to define the operating limits of the compressor by monitoring for two-phase flow, flow turbulence from the IGVs, and compressor choke and surge as the CO 2 inlet temperature is varied. Performance testing was conducted on an existing integrally-geared, two-stage main compressor designed for near-critical-point operation with CO 2 . This testing campaign validated the IGV design and operation, as well as improved the understanding and confidence in operating compressors and predicting performance characteristics near the critical point where fluid properties change rapidly with temperature. In addition to improving the robust operating limits of an sCO 2 compressor, the development of an IGV for the IGC system improved off-design compressor efficiency by 12%.

25 ENERGY STORAGE↗

Isokinetic Inlet Aboard Aircraft (INLETISOK-AIR) Instrument Handbook

Isokinetic Inlet aboard the aircraft designed by Brechtel (Hayward, California) and modified by Pacific Northwest National Laboratory (PNNL). Additional information can be found on the manufacturer’s website. An earlier model was used on the Gulfstream-159 (G-1) aircraft operated by the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Aerial Facility (AAF) until 2019. A newer version of this instrument will be deployed on the replacement Challenger 850 aircraft. Modifications to the inlet involve making the software compatible with the aircraft’s data acquisition system.

47 OTHER INSTRUMENTATION↗

Evaluations of Connectors, Inlets, and Adapters on Side-Load and Withstand Force

This report examines the mechanical forces that direct current fast charging (DCFC) electric vehicle supply equipment (EVSE) connectors and electric vehicle (EV) inlet ports experience during normal usage. As we witness the fast and growing variety of EVs, charge port locations, and bigger and more powerful EVSE configurations including the SAE J3400 North American Charging Standard (NACS), which has increased the use of adapters with J3400 and J1772 compatibility. These new conditions contribute to increased mechanical forces due to their size, weight and lever arm effect, which creates the need to study and compare these forces to the limits on UL2251 and IEC 62196-1 standards. This report focuses solely on high power DC charging EVSE connectors, EV inlets and adapters for the specific compatibility cases on J3400 with J1772. We first describe the details of the 100N and the 750N side-load evaluations as described in the standards, then present the data obtained by replicating these tests to finally go into more detail on the findings and our recommendations.

100N↗

Parametric Evaluation of RDE Inlet Performance using a Reduced-Order Model

This paper presents the results of a parametric study on the effects of inlet restriction, along with a number of other controlling parameters, using a previously developed reduced-order RDE inlet model. The results of this study will be used to inform subsequent high-fidelity CFD simulations and/or selection of experimental operating conditions which may be conducive to maximizing performance.

Bedick, Clinton↗

Perforations in jet engine supersonic inlet increase shock stability

Modification of a conventional jet engine internal compression supersonic inlet results in increased shock stability and thus, engine instantaneous response to changes in inlet air properties. This technique provides a large amount of bleed near the maximum pressure recovery at the expense of minor bleed flow during critical operation.

Keppler, C. R.↗

Effects of radial and circumferential inlet velocity profile distortions on performance of a short-length double-annular ram induction combustor

Inlet air velocity profile tests were conducted on a full-scale short-length 102-centimeter-diameter annual combustor designed for advanced gas turbine engine applications. The inlet profiles studied include radial distortions that were center peaked, and tip peaked, as well as a circumferential distortion which was center peaked for one-third of the circumference and flat for the other two-thirds. An increase in combustor pressure loss was the most significant effect of the radial air velocity distortions. With the circumferential distortion, exit temperature pattern factor doubled when compared to a flat velocity profile.

Schultz, D. F.↗

Performance comparison of three normal-shock position sensors for mixed-compression inlets

The performance of three types of normal shock position sensors for supersonic inlets is described. All three sensors determined the shock position from the presence of the large pressure gradient at the normal shock location. The logic means for the three sensors were: (1) electronic, using pressure transducers, (2) fluidic, and (3) direct-coupled pressure switches. The sensors were evaluated in a two-dimensional, Mach 2.7, supersonic inlet having 30-percent internal supersonic area contraction. Both dynamic (from 1 to 80 Hz) and static tests were conducted.

Dustin, M. O.↗

Theoretical and experimental internal flow characteristics of a 13.97-centimeter-diameter inlet at STOL takeoff and approach conditions

The theoretical and experimental internal flow characteristics of a 13.97-cm-diam inlet with centerbody retracted and extended are presented at STOL takeoff and approach operating conditions. The theoretical results were obtained from incompressible potential flow corrected for compressibility and boundary layer. Comparisons between theoretical internal surface static-pressure distributions and experimental data are presented for free-stream velocities of 0, 24, 32, and 45 m/sec for a range of inlet incidence angles from 0 to 50 deg. Surface static-pressure distributions are illustrated at circumferential locations of 0, 60, 120, and 180 deg. Surface Mach number distributions from the stagnation point to the diffuser exit are presented along with turbulent boundary-layer shape factors. In general, good agreement was found between the theoretical and experimental surface static pressure distributions.

Albers, J. A.↗

Investigation of flow fields within large scale hypersonic inlet models

Analytical and experimental investigations were conducted to determine the internal flow characteristics in model passages representative of hypersonic inlets for use at Mach numbers to about 12. The passages were large enough to permit measurements to be made in both the core flow and boundary layers. The analytical techniques for designing the internal contours and predicting the internal flow-field development accounted for coupling between the boundary layers and inviscid flow fields by means of a displacement-thickness correction. Three large-scale inlet models, each having a different internal compression ratio, were designed to provide high internal performance with an approximately uniform static-pressure distribution at the throat station. The models were tested in the Ames 3.5-Foot Hypersonic Wind Tunnel at a nominal free-stream Mach number of 7.4 and a unit free-stream Reynolds number of 8.86 X one million per meter.

Gnos, A. V.↗

Local flow measurements at the inlet spike tip of a Mach 3 supersonic cruise airplane

The flow field at the left inlet spike tip of a YF-12A airplane was examined using at 26 deg included angle conical flow sensor to obtain measurements at free-stream Mach numbers from 1.6 to 3.0. Local flow angularity, Mach number, impact pressure, and mass flow were determined and compared with free-stream values. Local flow changes occurred at the same time as free-stream changes. The local flow usually approached the spike centerline from the upper outboard side because of spike cant and toe-in. Free-stream Mach number influenced the local flow angularity; as Mach number increased above 2.2, local angle of attack increased and local sideslip angle decreased. Local Mach number was generally 3 percent less than free-stream Mach number. Impact-pressure ratio and mass flow ratio increased as free-stream Mach number increased above 2.2, indicating a beneficial forebody compression effect. No degradation of the spike tip instrumentation was observed after more than 40 flights in the high-speed thermal environment encountered by the airplane. The sensor is rugged, simple, and sensitive to small flow changes. It can provide accurate imputs necessary to control an inlet.

Johnson, H. J.↗