Unstructured low-Mach number viscous flow solver
The topics are presented in viewgraph form and include the following: governing equations; grid generation; numerical approach; results; and conclusions.
Philip C E Jorgenson↗
SEARCH · Engineering Papers
Results for “flow forming”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An Investigation of the Icing and Heated-air De-icing Characteristics of the R-2600-13 Induction System
A laboratory investigation was made on a Holley 1685-HB carburetor mounted on an R-2600-13 supercharger assembly to determine the icing characteristics and the heated-air de-icing requirements of this portion of the B-25D airplane induction system. Icing has been found to be most prevalent at relatively small throttle openings and, consequently, all runs were made at simulated 60-percent normal rated power condition. Icing characteristics were determined during a series of 15-minute runs over a range of inlet-air conditions. For the de-icing investigation severe impact ice was allowed to form in the induction system and the time required for the recovery of 95 percent of the maximum possible air flow at the original throttle setting was then determined for a range of wet-bulb temperatures. Results of these runs showed that ice on the walls of the carburetor adapter and on the rim of the impeller-shroud portion of the supercharger diffuser plate did not affect engine operation at 60-percent normal rated power. Ice that adversely affected the air flow and the fuel-air ratio was formed only on the central web of the carburetor and then only when the inlet air was saturated or contained free moisture in excess of saturation. No serious ice formations were observed at inlet-air temperatures above 66 0 F or with an inlet-air enthalpy greater than 34 Btu per pound. The maximum temperature at. which any trace of icing could be detected was 1110 F with a relative humidity of approximately 28 percent, The air-flow recovery time for emergency de-icing was 0.3 minute for.an enthalpy of 35 Btu per pound or wet-bulb temperature of 68 0 F. Further increase in enthalpy and wet-bulb temperature above these values resulted in very slight improvement in recovery time. The fuel-air ratio restored by a 5-Minute application of heated air was approximately 7 percent less than the initial value for cold-air conditions.
Chapman, Gilbert E.↗
Application of rotor mounted pressure transducers to analysis of inlet turbulence
Miniature pressure transducers installed near the leading edge of a fan blade were used to diagnose the non-uniform flow entering a subsonic tip speed turbofan on a static test stand. The pressure response of the blade to the inlet flow variations was plotted in a form which shows the space-time history of disturbances ingested by the rotor. Also, periodically sampled data values were auto- and cross-correlated as if they had been acquired from fixed hot wire anemometers at 150 equally spaced angles around the inlet. With a clean inlet and low wind, evidence of long, narrow turbulence eddies was easily found both in the boundary layer of the fan duct and outside the boundary layer. The role of the boundary layer was to follow and amplify disturbances in the outer flow. These eddies frequently moved around the inlet with a corkscrew motion as they passed through.
Hanson, D. B.↗
Investigation of Technologies to Improve Condenser Heat Transfer and Performance in a Relevant Coal-Fired Power Plant
Improvements in thermal power-generating plant performance is correlated directly to societal benefits including lower cost of reduced fuel consumption, resulting in lower cost of electricity for the consumer and reduced carbon emissions to the atmosphere. Warm steam exhausted from low-pressure steam turbines is condensed to liquid water on the exterior of thin-walled metal condenser tubes with cooling water passing through the tube interior. The condensation of steam creates a vacuum that supports turbine rotation and the concurrent generation of electricity. This vacuum is optimized when heat transfer across the wall of condenser tube is maximized. Common hindrances to heat transfer include foulants in cooling water that may form and adhere to the interior of condenser tubes, including mineral scale, microbiological films, and particulate deposition. Flowing cooling water may also include a laminar layer at the interior metal surfaces that travels more slowly than bulk water flow, serving to impede heat transfer. On the tube exterior, condensing steam forms an insulating layer of water that flows down the tube and reduces the effectiveness of cooling. Both the interior and exterior barriers to optimal heat transfer may be alleviated to some extent by surface treatments. On the tube interior, hydrophobic coatings may be applied that can reduced the adherence of foulants and of the laminar flow layer to the tube surface. On the tube exterior, hydrophobic coatings or mechanical treatments can be applied that may result in the termination of droplet growth and the departure of droplets from the surface rather than coalescence into a continuous layer of flowing water. Fourteen surface treatments were applied to condenser tubes in this study, including eight interior coatings and six exterior treatments, five of which were coatings and one a microstructural texture. Heat transfer measurement equipment simulating conditions in the condenser of an operating power plant was used to determine heat transfer coefficients by measuring sufficient flow, temperature, water chemistry and other data. Several of the tubes with interior surface treatments showed improvement in heat transfer coefficients compared with a plain (uncoated) tube, and several of the tubes with exterior surface treatments also showed enhanced heat transfer coefficients.
01 COAL, LIGNITE, AND PEAT↗
Nonlinear computation of wing-body-vertical tail-wake flows at low supersonic speeds
A numerical method based on the conservation form of the full potential equation has been applied to the problem of three-dimensional supersonic flows with embedded subsonic regions. The governing equation is cast in a nonorthogonal coordinate system, and the theory of characteristics is used to accurately monitor the type-dependent flow field. A conservative switching scheme is employed to transition from the supersonic marching procedure to a subsonic relaxation algorithm and vice versa. The newly developed computer program can handle arbitrary geometries with fuselage, wing, vertical tail and wake components at combined angle of attack and sideslip. Results are presented for a low supersonic Mach numbers flow over the Shuttle orbiter (including the OMS pods and vertical tail), and for flows over a realistic fighter type configuration. Comparisons with experimental data are shown to be in good agreement for various cases.
Szema, K.-Y.↗
Applicability of linearized-theory attached-flow methods to design and analysis of flap systems at low speeds for thin swept wings with sharp leading edges
Low-speed experimental force and data on a series of thin swept wings with sharp leading edges and leading and trailing-edge flaps are compared with predictions made using a linearized-theory method which includes estimates of vortex forces. These comparisons were made to assess the effectiveness of linearized-theory methods for use in the design and analysis of flap systems in subsonic flow. Results demonstrate that linearized-theory, attached-flow methods (with approximate representation of vortex forces) can form the basis of a rational system for flap design and analysis. Even attached-flow methods that do not take vortex forces into account can be used for the selection of optimized flap-system geometry, but design-point performance levels tend to be underestimated unless vortex forces are included. Illustrative examples of the use of these methods in the design of efficient low-speed flap systems are included.
Carlson, Harry W.↗
Model equation for simulating flows in multistage turbomachinery
A steady, three-dimensional average-passage equation system is derived for use in simulating multistage turbomachinery flows. These equations describe a steady, viscous flow that is periodic from blade passage to blade passage. From this system of equations, various reduced forms can be derived for use in simulating the three-dimensional flow field within multistage machinery. It is suggested that a properly scaled form of the average-passage equation system would provide an improved mathematical model for simulating the flow in multistage machines at design and, in particular, at off-design conditions.
Adamczyk, J. J.↗
Model equation for simulating flows in multistage turbomachinery
A steady, three-dimensional average-passage equation system is derived for use in simulating multistage turbomachinery flows. These equations describe a steady, viscous flow that is periodic from blade passage to blade passage. From this system of equations, various reduced forms can be derived for use in simulating the three-dimensional flow field within multistage machinery. It is suggested that a properly scaled form of the averaged-passage equation system would provide an improved mathematical model for simulating the flow in multistage machines at design and, in particular, at off-design conditions.
Adamczyk, J. J.↗
Probing Supraglacial Debris on Mars 2: Crater Morphology
Lobate debris aprons (LDA), lineated valley fill (LVF), and concentric crater fill (CCF) on Mars, interpreted to bedebris-covered glaciers, possess craters with a suite of distinct interior landforms (called "ring-mold craters")that have been attributed to the presence of glacial ice at depth or surface modification processes. We testedcurrent hypotheses for the formation of ring-mold craters by conducting a comprehensive analysis of the size andmorphology of 16,457 impact craters 125m in diameter formed within glacial deposits in DeuteronilusMensae. Two major groups, bowl-shaped craters and ring-mold craters, are found, with at least nine distinctcrater types. While there is statistical difference in median diameters between these crater types, this differenceis relatively small and is within the estimated uncertainty in diameter measurements and may be related to moreenhanced erosion of the rims of ring-mold craters. Clear degradation sequences are observed, supporting a rolefor post-impact modification in producing at least some of the diversity in crater landforms. The spatial densityof ring-mold craters is also directly correlated with the development of LDA, LVF, and CCF surface textures. Flowlineations cross-cut two ring-mold crater types but they maintain their circular planforms in some cases, suggestingthat the craters initially formed completely within mantling layers deposited after glacial flow hadceased. We also find analogous craters in non-glacial units; glacial ice is therefore not required to form theobserved morphologic diversity. Our observations are most consistent with formation of crater landforms byemplacement and modification of at least two depositional episodes of icy dust (i.e., "mantle"). This mantle wasinitially tens of meters in thickness to support crater formation, and has experienced much downwasting anderosion since emplacement. Derived crater retention ages of 460 Ma for LDA, LVF, and CCF features in the regiontherefore reflect deposition of mantle units and only give a very minimum age for the formation of LDA, LVF, andCCF
Geological↗
Split Space-Marching Finite-Volume Method for Chemically Reacting Supersonic Flow
A space-marching finite-volume method employing a nonorthogonal coordinate system and using a split differencing scheme for calculating steady supersonic flow over aerodynamic shapes is presented. It is a second-order-accurate mixed explicit-implicit procedure that solves the inviscid adiabatic and nondiffusive equations for chemically reacting flow in integral conservation-law form. The relationship between the finite-volume and differential forms of the equations is examined and the relative merits of each discussed. The method admits initial Cauchy data situated on any arbitrary surface and integrates them forward along a general curvilinear coordinate, distorting and deforming the surface as it advances. The chemical kinetics term is split from the convective terms which are themselves dimensionally split, thereby freeing the fluid operators from the restricted step size imposed by the chemical reactions and increasing the computational efficiency. The accuracy of this splitting technique is analyzed, a sufficient stability criterion is established, a representative flow computation is discussed, and some comparisons are made with another method.
Rizzi, Arthur W.↗
On the Maximum Stellar Rotation to Form a Black Hole without an Accompanying Luminous Transient
The collapse of a massive star with low angular momentum content is commonly argued to result in the formation of a black hole without an accompanying bright transient. Our goal in this Letter is to understand the flow in and around a newly-formed black hole, involving accretion and rotation, via general relativistic hydrodynamics simulations aimed at studying the conditions under which infalling material can accrete without forming a centrifugally supported structure and, as a result, generate no effective feedback. If the feedback from the black hole is, on the other hand, significant, the collapse would be halted and we suggest that the event is likely to be followed by a bright transient. We find that feedback is only efficient if the specific angular momentum of the infalling material at the innermost stable circular orbit exceeds that of geodesic circular flow at that radius by at least≈20%. We use the results of our simulations to constrain the maximal stellar rotation rates of the disappearing massive progenitors PHL293B-LBV and N6946-BH1, and to provide an estimate of the overall rate of disappearing massive stars. We find that about a few percent of single O-type stars with measured rotational velocities are expected to spin below the critical value before collapse and are thus predicted to vanish without a trace.
Scott C Noble↗
Thermal convection in a rotating shear flow
The dynamics of thermal convection in a rotating shear flow was studied using a three-dimensional time-dependent numerical model of the flow. The model assumes a sheared zonal wind in the form of an atmospheric jet stream and considers convective motions imbedded in this flow. It was found that rotation plays a vital role in the dynamics. Without rotation, the convective motions extract energy and momentum from the mean zonal flow. With rotation, the convective motions feed the energy and momentum into the mean flow. The results show how the small-scale convection might influence the large-scale dynamics of rotating stars and planets.
Hathaway, David H.↗
Fluid volcanism on Miranda and Ariel - Flow morphology and composition
Several types of volcanic units have been recognized on the icy Uranian satellites Miranda and Ariel. On Miranda, ridges characterized by crest grooves are up to 10 km wide and 500 m high. A continuous flat-topped flow band also 10 km wide and 500 m high forms the outer southern margin of Elsinore Corona, which appears to comprise coalesced flow bands and ridges. On Ariel, in addition to at least one ridge unit similar to those on Miranda, flood plains material has covered the floors of deep chasmata (grabens) and an irregular depression. Flows on both satellites are characterized by linear vent geometries and distinct topographic margins, which indicate extrusion of a relatively viscous material. The topography of the flows can be used to estimate flow viscosity or yield strength using a Bingham plastic model. Extrusion viscosity estimates, incorporating plausible volcanologically based emplacement time scales and a rigid crust correction, range from 10 MP to 1 GP (10 TP in the unlikely absence of a chilled crust). Viscosity estimates are dependent on the assumed emplacement time scale, however, and could be as high as 10 PP, if a solid-state-based time scale is assumed.
Schenk, Paul M.↗
Low Reynolds number kappa-epsilon and empirical transition models for oscillatory pipe flow and heat transfer
Stirling engine heat exchangers are shell-and-tube type with oscillatory flow (zero-mean velocity) for the inner fluid. This heat transfer process involves laminar-transition turbulent flow motions under oscillatory flow conditions. A low Reynolds number kappa-epsilon model, (Lam-Bremhorst form), was utilized in the present study to simulate fluid flow and heat transfer in a circular tube. An empirical transition model was used to activate the low Reynolds number k-e model at the appropriate time within the cycle for a given axial location within the tube. The computational results were compared with experimental flow and heat transfer data for: (1) velocity profiles, (2) kinetic energy of turbulence, (3) skin friction factor, (4) temperature profiles, and (5) wall heat flux. The experimental data were obtained for flow in a tube (38 mm diameter and 60 diameter long), with the maximum Reynolds number based on velocity being Re(sub max) = 11840, a dimensionless frequency (Valensi number) of Va = 80.2, at three axial locations X/D = 16, 30 and 44. The agreement between the computations and the experiment is excellent in the laminar portion of the cycle and good in the turbulent portion. Moreover, the location of transition was predicted accurately. The Low Reynolds Number kappa-epsilon model, together with an empirical transition model, is proposed herein to generate the wall heat flux values at different operating parameters than the experimental conditions. Those computational data can be used for testing the much simpler and less accurate one dimensional models utilized in 1-D Stirling Engine design codes.
Bauer, Christopher↗
Three-Dimensional Transonic Flow Theory Applied to Slender Wings and Bodies
The present paper re-examines the derivation of the integral equations for transonic flow around slender wings and bodies of revolution, giving special attention to conditions resulting from the presence of shock waves and to the reduction of the relations to the special forms necessary for the discussion of sonic flow, that is, flow at free-stream Mach number 1.
Heaslet, Max A↗
Forming Weld Lands On Metal Plates
Forming shoe pounds edge of newly inserted plate workpiece. After many passes of shoe and advances of plate, thick land builds up at edge. Workpiece heated to enable metal to flow without strain hardening. Proposed upset-forming process replaces relatively expensive, time-consuming, and wasteful process in which integral weld lands created by machining metal away from plates everywhere except at lands.
Weddendorf, Bruce↗
Concerning the flow about ring-shaped cowlings of finite thickness Part I
It is shown how one may obtain, in a simple manner, the forms of ring-shaped bodies from existing tables of functions according to the customary method of superposition of flow due to singularities and parallel flow. A number of examples of the forms and pressure distributions of annular source bodies with and without hub body are given, and the inlet conditions of such ring-shaped cowlings are investigated. Furthermore, the annular bodies of finite length are indicated that correspond to Joukowsky profiles for the two-dimensional case. The examples are to give a basis for the design of cross-sectional forms of ring-shaped cowlings and a survey of the flows to be expected.
FLOW, INCOMPRESSIBLE↗
The origin of the solar wind
The high speed solar wind, which is associated with coronal holes and unipolar interplanetary magnetic field, has now been observed in situ beyond 0.3 a.u. and at latitudes up to 80 degrees. Its important characteristics are that it is remarkably steady in terms of flow properties and composition and that the ions, especially minor species, are favored in terms of heating and acceleration. We have proposed that the high speed wind, with its associated coronal holes, forms the basic mode of solar wind flow. In contrast, the low speed wind is inherently non-stationary, filamentary and not in equilibrium with conditions at the coronal base. It is presumably the result of continual reconfigurations of the force-free magnetic field in the low-latitude closed corona which allow trapped plasma to drain away along transiently open flux tubes. Observations of high speed solar wind close to its source are hampered by the essential heterogeneity of the corona, even at sunspot minimum. In particular it is difficult to determine more than limits to the density, temperature and wave amplitude near the coronal base as a result of contamination from fore- and back-ground plasma. We interpret the observations as indicating that the high speed solar wind originates in the chromospheric network, covering only about 1% of the surface of the sun, where the magnetic field is complex and not unipolar. As a result of small-scale reconnection events in this 'furnace', Alfven waves are generated with a flat spectrum covering the approximate range 10 kHz to 10 Hz. The plasma is likely to be produced as a result of downwards thermal conduction and possibly photoionization at the top of the low density chromospheric interface to the furnace, thus controlling the mass flux in the wind. The immediate source of free (magnetic) energy is in the form of granule-sized loops which are continually carried into the network from the sides. The resulting wave spectrum is such that energy can be efficiently transferred to the ions within a few solar radii of the base of the corona, favoring heavy species and creating stable, fast solar wind.
Axford, W. I.↗