Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Supercritical Carbon Dioxide Power Cycle Design and Configuration Optimization to Minimize Levelized Cost of Energy of Molten Salt Power Towers Operating at 650 °C

This analysis investigates the design, cost, and performance of the simple, recompression, and partial-cooling configurations of the supercritical carbon dioxide power cycle integrated with a molten salt power tower concentrating solar power system. This paper uses a steady-state model to design each cycle with varying amounts of recuperator conductance to understand performance and cost trade-offs. The recompression cycle can achieve a higher thermal efficiency than the partial-cooling cycle, and the partial-cooling cycle achieves a higher thermal efficiency than the simple cycle. The partial-cooling cycle is the most expensive cycle because it requires more total turbomachinery capacity. However, the partial-cooling cycle has the largest temperature range of heat input. This feature leads to cheaper two-tank thermal energy storage, higher receiver efficiencies, and lower mass flow rates in the power tower. Crucially, the lower mass flow rates significantly reduce pump electricity consumption relative to the recompression-cycle system. Consequently, this study finds that the power tower system integrated with the partial-cooling cycle is both cheaper and generates more net electricity than systems integrated with the other two cycles. Finally, this paper presents a parametric study on the air-cooler approach temperature and shows that small approach temperatures can improve cycle efficiency and increase the temperature range of heat input, which can lead to smaller optimal approach temperatures than may be expected.

14 SOLAR ENERGY↗

Improving low-level plasma protein mass spectrometry-based detection for candidate biomarker discovery and validation

Methods. To improve the detection of low abundance protein candidate biomarker discovery and validation, particularly in complex biological fluids such as blood plasma, increased sensitivity is desired using mass spectrometry (MS)-based instrumentation. A key current limitation on the sensitivity of electrospray ionization (ESI) MS is due to the fact that many sample molecules in solution are never ionized, and the vast majority of the ions that are created are lost during transmission from atmospheric pressure to the low pressure region of the mass analyzer. Two key technologies, multi-nanoelectrospray emitters and the electrodynamic ion funnel have recently been developed and refined at Pacific Northwest National Laboratory (PNNL) to greatly improve the ionization and transmission efficiency of ESI MS based analyses. Multi-emitter based ESI enables the flow from a single source (typically a liquid chromatography [LC] column) to be divided among an array of emitters (Figure 1). The flow rate delivered to each emitter is thus reduced, allowing the well-documented benefits of nanoelectrospray 1 for both sensitivity and quantitation to be realized for higher flow rate separations. To complement the increased ionization efficiency afforded by multi-ESI, tandem electrodynamic ion funnels have also been developed at PNNL, and shown to greatly improve ion transmission efficiency in the ion source interface.2, 3 These technologies have been integrated into a triple quadrupole mass spectrometer for multiple reaction monitoring (MRM) of probable biomarker candidates in blood plasma and show promise for the identification of new species even at low level concentrations.

59 BASIC BIOLOGICAL SCIENCES↗

Performance of Typical Rear-Stage Axial-Flow Compressor Rotor Blade Row at Three Different Blade Setting Angles

A comparison of the performance of a single-stage rotor run at three different blade setting angles is presented. The rotor was of a design typical for a last stage of a multistage compressor. At each setting angle, the rotor blade row was operated from 53 to 100 percent of equivalent maximum speed (850 ft/sec tip speed) at constant inlet pressure. Hot-wire anemometry was used to observe rotating-stall and surge patterns in time unsteady flow. Results indicated that an increase in peak pressure ratio and an increase in maximum equivalent weight flow were obtained at each speed investigated when the blade setting angle was decreased. An increase in peak efficiency was achieved with decrease in blade setting angle for part of the range of speeds investigated. However, the peak efficiencies for the three blade setting angles were approximately the same at the maximum speed investigated. The flow ranges for all three configurations were about the same at minimum speed and decreased at almost the same rate when the rotative speed was increased through part of the range of speeds investigated. At maximum speed, the flow range for the smallest setting angle was considerably less than the flow range for the other two configurations. A decrease in efficiency and flow range for the smallest blade setting angle at maximum speed can be attributed primarily to a Mach number effect. In addition, because of the difference in projected axial chord lengths at the casing wall, some effect on performance could be expected from the change in three-dimensional flow occurring at the tip. Rotating-stall characteristics for the two smaller blade setting angles were essentially the same. Only surge could be detected for the largest blade setting angle in the unstable-flow region of operation.

Kussoy, Marvin I.↗

Core compressor exit stage study, 2

A total of two three-stage compressors were designed and tested to determine the effects of aspect ratio on compressor performance. The first compressor was designed with an aspect ratio of 0.81; the other, with an aspect ratio of 1.22. Both compressors had a hub-tip ratio of 0.915, representative of the rear stages of a core compressor, and both were designed to achieve a 15.0% surge margin at design pressure ratios of 1.357 and 1.324, respectively, at a mean wheel speed of 167 m/sec. At design speed the 0.81 aspect ratio compressor achieved a pressure ratio of 1.346 at a corrected flow of 4.28 kg/sec and an adiabatic efficiency of 86.1%. The 1.22 aspect ratio design achieved a pressure ratio of 1.314 at 4.35 kg/sec flow and 87.0% adiabatic efficiency. Surge margin to peak efficiency was 24.0% with the lower aspect ratio blading, compared with 12.4% with the higher aspect ratio blading.

Behlke, R. F.↗

Development of Efficient Real-Fluid Model in Simulating Liquid Rocket Injector Flows

The characteristics of propellant mixing near the injector have a profound effect on the liquid rocket engine performance. However, the flow features near the injector of liquid rocket engines are extremely complicated, for example supercritical-pressure spray, turbulent mixing, and chemical reactions are present. Previously, a homogeneous spray approach with a real-fluid property model was developed to account for the compressibility and evaporation effects such that thermodynamics properties of a mixture at a wide range of pressures and temperatures can be properly calculated, including liquid-phase, gas- phase, two-phase, and dense fluid regions. The developed homogeneous spray model demonstrated a good success in simulating uni- element shear coaxial injector spray combustion flows. However, the real-fluid model suffered a computational deficiency when applied to a pressure-based computational fluid dynamics (CFD) code. The deficiency is caused by the pressure and enthalpy being the independent variables in the solution procedure of a pressure-based code, whereas the real-fluid model utilizes density and temperature as independent variables. The objective of the present research work is to improve the computational efficiency of the real-fluid property model in computing thermal properties. The proposed approach is called an efficient real-fluid model, and the improvement of computational efficiency is achieved by using a combination of a liquid species and a gaseous species to represent a real-fluid species.

Cheng, Gary↗

Performance of Compressor of XJ-41-V Turbojet Engine: Compressor Static-Pressure Rise at Equivalent Compressor Speeds of 5000, 7000, 8000, and 9000 rpm - 3

At the request of the Air Materiel Command, Army Air Forces, an investigation is being conducted at the NACA Cleveland laboratory to determine the performance characteristics of the XJ-41-V turbojet-engine compressor. The static-pressure variation in the direction of flow through the compressor was presented in reference 1 for an equivalent speed of 8000 rpm. An analysis of these pressure indicated that the maximum-flow limitation of the compressor was caused by separation, which reduced the effective flow area at the vaned-collector entrance. As a result of this analysis, the flow area at the vaned-collector entrance was increased to obtain larger mass flows. The area increase was obtained by cutting back the entrance edges of the collector vanes, which resulted in an increased vaneless-diffuser radius. Comparative performance of the original and revised compressors at an equivalent speed of 8000 rpm is presented. The static-pressure rise through the compressor, determined from static pressures at the impeller entrance and the vaned-collector exit, is also presented together with the compressor adiabatic efficiency and the mass flow over an equivalent speed range from 5000 to 9000 rpm. These static-pressure data are presented for the purpose of correlating the compressor performance with the turbojet-engine performance.

Creagh, John W. R.↗

Aerodynamic performance of 0.4066-scale model to JT8D refan stage

The aerodynamic performance of a scale model of the split flow JT8D rafan stage is presented over a range of flows at speeds from 40 to 100 percent design. The bypass stage peak efficiency of 0.800 occurred at a total weight flow of 35.82 kilograms per second and a pressure ratio of 1.697. The stall margin was 15 percent based on pressure ratio and weight flow at stall and peak efficiency conditions. The data indicated that the hub region of the core stators was choked at design speed over the entire flow range tested.

Moore, R. D.↗

Calculation of plasma properties in ion sources

Simple algebraic equations are developed that can be used to calculate the average primary electron density, the average primary to Maxwellian density ratio, and the average Maxwellian electron temperature in the discharge chamber of a cusped magnetic field ion source. These properties may be calculated as functions of the propellant gas flow rate and the propellant utilization efficiency. Each of the plasma properties calculated using the model agrees well with the corresponding experimental data for both argon and xenon gases over a wide range of propellant flow rates and utilization efficiencies.

Brophy, J. R.↗

Viscous Shock-Layer Analysis of Two-Dimensional and Axisymmetric Flows

Results are obtained for cylindrical leading edges of proposed transatmospheric vehicles by employing a two-dimensional viscous shock-layer code for nonequilibrium gas flows. The accuracy and efficiency of the planar code is verified through detailed comparisons with other predictions. This study includes results for 6-deg half-angle bodies with nose radii ranging from 0.01 to 2.0 ft for both cylindrically blunted wedges and spherically blunted cones (included for comparison). Some results are presented as a ratio of the noncatalytic to the corresponding fully catalytic heating value to illustrate the maximum potential for a heating reduction in dissociated nonequilibrium flows. Generally, this ratio and the individual heating rates are smaller for cylindrically blunted wedges with small nose radii as compared to the spherically blunted cones (for the same nose radius). Therefore, a larger potential exists for heating reduction in cylindrically blunted as compared with the spherically blunted surfaces. However, the results presented at higher altitudes (where the slip effects become important) show that the spherically, blunted nose gives lower stagnation-point heating due to stronger merged shock-layer effects as compared with a cylindrically blunted nose.

Gupta, Roop N.↗

An experimental study of a three-dimensional thrust augmenting ejector using laser Doppler velocimetry

Flow field measurements were obtained in a three-dimensional thrust augmenting ejector using laser Doppler velocimetry and hot wire anemometry. The primary nozzle, segmented into twelve slots of aspect ratio 3.0, was tested at a pressure ratio of 1.15. Results are presented on the mean velocity, turbulence intensity, and Reynolds stress progressions in the mixing chamber of the constant area ejector. The segmented nozzle was found to produce streamwise vortices that may increase the mixing efficiency of the ejector flow field. Compared to free jet results, the jet development is reduced by the presence of the ejector walls. The resulting thrust augmentation ratio of this ejector was also calculated to be 1.34.

Storms, Bruce Lowell↗

Bridging Scales in Black Hole Accretion and Feedback: Relativistic Jet Linking the Horizon to the Host Galaxy

Simulating black hole (BH) accretion and feedback from the BH horizon to galactic scales is extremely challenging, as it involves a vast range of scales. Recently, our multizone method has successfully achieved global dynamical steady states of hot accretion flows in 3D general relativistic magnetohydrodynamic simulations by tracking the bidirectional interaction between a nonspinning BH and its host galaxy. In this paper, we present technical improvements to the method and apply it to spin a * = 0.9 BHs, which power relativistic jets. We first test the new multizone setup with a smaller Bondi radius, R B ≈ 400 r g , where r g is the gravitational radius. The strongly magnetized accretion launches a relativistic jet with an intermediate feedback efficiency η ∼ 30%, in between that of a prograde (η ∼ 100%) and retrograde (η ∼ 10%) torus. Interestingly, both prograde and retrograde simulations also eventually converge to the same intermediate efficiency when evolved long enough, as accumulated magnetic fields remove gas rotation. We then extend strongly magnetized simulations to larger Bondi radii, R B ≈ 2 × 10 3 , 2 × 10 4 , 2 × 10 5 r g . We find that the BH accretion rate $\dot{M}$ is suppressed with respect to the Bondi rate as $\dot{M}_{\textrm{B}}$ as $\dot{M}/\dot{M}_{\textrm{B}} ∝ R_{\textrm{B}}^{-1/2}$. However, despite some variability, the time-averaged feedback efficiency remains at η ∼ 30%, independent of R B . This suggests that BH feedback efficiency in hot accretion flows is mainly governed by the BH spin (a * ) rather than by the galactic properties (R B ). From these first-principles simulations, we provide a feedback subgrid prescription for cosmological simulations: $\dot{E}_{\textrm{fb}} = 2$ x $10^{-3}[R_{\textrm{B}}/(2$ x $10^5 r_g)]^{-1/2}$ $\dot{M}_{\textrm{B}}c^2$ for BH spin a * = 0.9.

79 ASTRONOMY AND ASTROPHYSICS↗

An upwind multigrid method for solving viscous flows on unstructured triangular meshes

A multigrid algorithm is combined with an upwind scheme for solving the two dimensional Reynolds averaged Navier-Stokes equations on triangular meshes resulting in an efficient, accurate code for solving complex flows around multiple bodies. The relaxation scheme uses a backward-Euler time difference and relaxes the resulting linear system using a red-black procedure. Roe's flux-splitting scheme is used to discretize convective and pressure terms, while a central difference is used for the diffusive terms. The multigrid scheme is demonstrated for several flows around single and multi-element airfoils, including inviscid, laminar, and turbulent flows. The results show an appreciable speed up of the scheme for inviscid and laminar flows, and dramatic increases in efficiency for turbulent cases, especially those on increasingly refined grids.

Bonhaus, Daryl Lawrence↗

Computer program for design analysis of radial-inflow turbines

A computer program written in FORTRAN that may be used for the design analysis of radial-inflow turbines was documented. The following information is included: loss model (estimation of losses), the analysis equations, a description of the input and output data, the FORTRAN program listing and list of variables, and sample cases. The input design requirements include the power, mass flow rate, inlet temperature and pressure, and rotational speed. The program output data includes various diameters, efficiencies, temperatures, pressures, velocities, and flow angles for the appropriate calculation stations. The design variables include the stator-exit angle, rotor radius ratios, and rotor-exit tangential velocity distribution. The losses are determined by an internal loss model.

Glassman, A. J.↗

LDV measurements on propellers

Laser Doppler velocimeter (LDV) measurements of the flow velocity around high-efficiency propeller blades for high disk loading turboprop propulsion systems are reported. The wind-tunnel flow around sets of eight straight and swept propeller blades with the same twist and chord distributions was measured using a conventional two-color dual scatter LDV system. The measurements of the axial flow velocities a small distance in front of the propeller blade, between the blade row, and downstream of the propeller are shown to provide information necessary for the determination of overall performance, swirl angle distribution, blade loading distributions, local lift and drag coefficients, interference effects, shock location, local induced velocities, wake characteristics and stall pattern.

Sullivan, J. P.↗

Performance sensitivity analysis of Department of Energy-Chrysler upgraded automotive gas turbine engine, S/N 5-4

The performance sensitivity of a two-shaft automotive gas turbine engine to changes in component performance and cycle operating parameters was examined. Sensitivities were determined for changes in turbomachinery efficiency, compressor inlet temperature, power turbine discharge temperature, regenerator effectiveness, regenerator pressure drop, and several gas flow and heat leaks. Compressor efficiency was found to have the greatest effect on system performance.

Johnsen, R. L.↗

An approximate factorization solution of the Navier-Stokes equations for transonic flow using body-fitted coordinates with application to NACA 64A010 airfoils

The implementation of the approximate factorization algorithm and its ability to efficiently and accurately describe transonic flow about an NACA 64A010 airfoil section is examined. The approximate factorization algorithm is developed from the nondimensional, conservative, vectorized Navier-Stokes equations expressed in curvilinear coordinates. Equations of state and transport coefficient relations appropriate to atmospheric air are appended to close the system of partial differential equations. An algebraic turbulence model is also incorporated into the equation set. This algorithm was verified by investigating the flow about an NACA 64A010 airfoil at 0, 2, and 3.5 deg angle of attack for free-stream conditions of 2,000,000 Reynolds number and 0.8 Mach number. Overall results were in good qualitative agreement with wind tunnel data sets. However, while nondimensional times of six were attained, numerical difficulties prevented any case from reaching a true steady state.

Copper, G. K.↗

Heat Transfer and Fluid Dynamics Measurements in the Expansion Space of a Stirling Cycle Engine

The heater (or acceptor) of a Stirling engine, where most of the thermal energy is accepted into the engine by heat transfer, is the hottest part of the engine. Almost as hot is the adjacent expansion space of the engine. In the expansion space, the flow is oscillatory, impinging on a two-dimensional concavely-curved surface. Knowing the heat transfer on the inside surface of the engine head is critical to the engine design for efficiency and reliability. However, the flow in this region is not well understood and support is required to develop the CFD codes needed to design modern Stirling engines of high efficiency and power output. The present project is to experimentally investigate the flow and heat transfer in the heater head region. Flow fields and heat transfer coefficients are measured to characterize the oscillatory flow as well as to supply experimental validation for the CFD Stirling engine design codes. Presented also is a discussion of how these results might be used for heater head and acceptor region design calculations.

Jiang, Nan↗

A Streaming Language Implementation of the Discontinuous Galerkin Method

We present a Brook streaming language implementation of the 3-D discontinuous Galerkin method for compressible fluid flow on tetrahedral meshes. Efficient implementation of the discontinuous Galerkin method using the streaming model of computation introduces several algorithmic design challenges. Using a cycle-accurate simulator, performance characteristics have been obtained for the Stanford Merrimac stream processor. The current Merrimac design achieves 128 Gflops per chip and the desktop board is populated with 16 chips yielding a peak performance of 2 Teraflops. Total parts cost for the desktop board is less than $20K. Current cycle-accurate simulations for discretizations of the 3-D compressible flow equations yield approximately 40-50% of the peak performance of the Merrimac streaming processor chip. Ongoing work includes the assessment of the performance of the same algorithm on the 2 Teraflop desktop board with a target goal of achieving 1 Teraflop performance.

Barth, Timothy↗