Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data inventory”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

A preliminary training guide for utilizing high-altitude, color-infrared photography in compiling soil maps

Instruction for acquiring and analytically processing small-scale color-infrared photography to perform a soil resources inventory over forests of the southern U.S. is provided. Planning the project; acquiring aerial photography, materials, equipment and supplemental data; and preparing the photography for analysis are discussed. The procedures for preparing ancillary and primary component overlays are discussed. The use of correlation charts and dichotomous keys for mountain landforms, water regime, and vegetation is explained.

Weaver, J. E.↗

Orbital performance of communication satellite microwave power amplifiers (MPAs)

This paper presents background data on the performance of microwave power amplifiers (MPAs) used as transmitters in currently operating commercial communication satellites. Specifically aspects of two competing MPA types are discussed. These are well known TWTA (travelling wave tube amplifier) and the SSPA (solid state power amplifier). Extensive in-orbit data has been collected from over 2000 MPAs in 1991 and 1993. The study in 1991 invovlved 75 S/C (spacecraft) covering 463 S/C years. The 1993 'second-look' study encompassed a slightly different population of 72 S/C with 497 S/C years of operation. A surprising result of both studies was that SSPAs, although quite reliable, did not achieve the reliability of TWTAs were one-third more reliable in the 1993 study. This was at C-band with comparable power amplifiers, e.g. 6-16W of RF output power and similar gains. Data at K(sub u)-band is for TWTAs only since there are no SSPAs in the current S/C inventory. The other complementary result was that the projected failure rates used as S/C payload design guidelines were, on average, somewhat higher for TWTAs than the actual failure rates uncovered by this study. SSPA rates were as projected.

Strauss, R.↗

Fall, Recovery and Characterization of the Novato L6 Chondrite Breccia

The Novato L6 chondrite fragmental breccia fell in California on 17 October 2012, and was recovered after the Cameras for Allsky Meteor Surveillance (CAMS) project determined the meteor's trajectory between 95 and 45 km altitude. The final fragmentation at 33 1 km altitude was exceptionally well documented by digital photographs. The first sample was recovered before rain hit the area. First results from a consortium study of the meteorite's characterization, cosmogenic and radiogenic nuclides, origin and conditions of the fall are presented. Some meteorites did not retain fusion crust and show evidence of spallation. Before entry, the meteoroid was 35+/-5 cm in diameter (mass 80+/-35 kg) with a cosmic ray exposure age of 9+/-1 Ma, if it had a one-stage exposure history. However, based on the cosmogenic nuclide inventory, a two-stage exposure history is more likely, with lower shielding in the last few Ma. Thermoluminescence data suggest a collision event within the last approx. 0.1 Ma. Novato likely belonged to the class of shocked L chondrites that have a common shock age of 470 Ma, based on the U,Th-He age of 460+/-220 Ma. The measured orbits of Novato, Jesenice and Innisfree are consistent with a proposed origin of these shocked L chondrites in the Gefion asteroid family, but leave open the possibility that they came to us directly from the 5:2 mean motion resonance with Jupiter. Novato experienced a stronger compaction than did other L6 chondrites of shock-stage S4. Despite this, a freshly broken surface shows a wide range of organic compounds.

meteorites↗

Logistics Reduction: RFID Enabled Autonomous Logistics Management (REALM) (LR-REALM)

The Advanced Exploration Systems (AES) Logistics Reduction (LR) project Radio-frequency identification (RFID) Enabled Autonomous Logistics Management (REALM) task focuses on the subset of autonomous logistics management functions pertaining to automated localization and inventory of all physical assets pertaining to, or within, a vehicle utilizing RFID technologies. REALM technology can provide detailed data to enable autonomous operations such as automated crew procedure generation and robotic interaction with logistics and deep space habitats; this is especially of value where communication delays with Earth drive the need for self-reliance. The REALM project will conduct a series of ISS technology demonstrations. The first ISS demonstration, REALM-1, started in February 2017 and was completed at the end of FY19 when it was transitioned to the ISS program for sustaining operations. The second ISS demonstration, REALM-2, started late2019 and will continue for at least one year.

NASA TechPort↗

A Sulfur Dioxide Covariance-Based Retrieval Algorithm (COBRA): Application to TROPOMI Reveals New Emission Sources

Sensitive and accurate detection of sulfur dioxide (SO 2 ) from space is important for monitoring and estimating global sulfur emissions. Inspired by detection methods applied in the thermal infrared, we present here a new scheme to retrieve SO 2 columns from satellite observations of ultraviolet back-scattered radiances. The retrieval is based on a measurement error covariance matrix to fully represent the SO 2 -free radiance variability, so that the SO 2 slant column density is the only retrieved parameter of the algorithm. We demonstrate this approach, named COBRA, on measurements from the TROPOspheric Monitoring Instrument (TROPOMI) aboard the Sentinel-5 Precursor (S-5P) satellite. We show that the method reduces significantly both the noise and biases present in the current TROPOMI operational DOAS SO 2 retrievals. The performance of this technique is also benchmarked against that of the Principal Component Algorithm (PCA) approach. We find that the quality of the data is similar and even slightly better with the proposed COBRA approach. The ability of the algorithm to retrieve SO 2 accurately is also further supported by comparison with ground-based observations. We illustrate the great sensitivity of the method with a high-resolution global SO 2 map, considering two and a half years of TROPOMI data. In addition to the known sources, we detect many new SO 2 emission hotspots worldwide. For the largest sources, we use the COBRA data to estimate SO 2 emission rates. Results are comparable to other recently published TROPOMI-based SO 2 emissions estimates, but the associated uncertainties are significantly lower than with the operational data. Next, for a limited number of weak sources, we demonstrate the potential of our data for quantifying SO 2 emissions with a detection limit of about 8 kt yr -1 , a factor of 4 better than the emissions derived from the Ozone Monitoring Instrument (OMI). We anticipate that the systematic use of our TROPOMI COBRA SO 2 column data set at a global scale will allow identifying and quantifying missing sources, and help improving SO 2 emission inventories.

SO2↗

Risk-Informed Operations and Maintenance Decision Making Using Deep Reinforcement Learning

A challenge for operating nuclear power plants is the significant cost of operations and maintenance, at times consuming up to 66% of annual operating costs. This project aims to build a framework for a risk-informed asset-management tool that integrates inspections, repairs, spare-part inventory, supply chain, and business choices to lower overall O&M costs. Our approach uses a combination of data-driven modeling and deep reinforcement learning to create and implement optimal maintenance policies for the existing nuclear fleet, as well as new advanced reactors. The creation of an asset management tool that uses these advanced methods will give operators new capabilities to help reduce the burden of O&M spending in nuclear power plants.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Air Quality Analysis and Tools For Policy

South Asia is home to some of the most significant air quality challenges in the world. More than 99% of the region’s population is exposed to unhealthy fine particulate matter (PM2.5) concentrations, as defined by the World Health Organization. Recent policy initiatives in South Asia show that air quality policy is a priority, given the health impacts of air pollution. At the same time, capacity and data to assess and address air pollution remains limited in many areas. The main objective of this report is to outline a set of publicly-available tools that can be used to inform policies to improve air quality in South Asia. The report primarily focuses on tools such as emission inventories and integrated modeling systems with country-level resolution and illustrates their air quality assessment capabilities through examples and brief technical summaries. The report focuses on: (a) the Community Emissions Data System (CEDS) that provides historical emissions of key pollutants for all countries in South Asia, and (b) profiles an analysis of Indian air pollution and policy scenarios, using several integrated modeling tools. Both of these examples draw on recent research and data that outlines the scale of the challenge as well as the policy options for reducing air pollution in the region. The report concludes with key recommendations for regional stakeholders working towards mitigating air pollution in South Asia.

54 ENVIRONMENTAL SCIENCES↗

Quantifying Annual Industrial Locomotive Energy Consumption in the United States

While US Class 1 railroad locomotive rosters and annual fuel consumption are well-documented, considerably less is known regarding the overall energy consumption of operations involving industrial locomotives. To determine the energy savings potential of this rail operating sector, the objective of this research is to develop an inventory of US industrial locomotives and a baseline estimate of their annual energy consumption. Creating an industrial locomotives roster from public data is challenging given their diverse ownership by shippers or leasing companies, and operating locales largely out of public view. By cross-referencing public data on locomotive reporting marks, serial numbers, online images and aerial images, the project team confirmed the age, model and horsepower of over one thousand industrial locomotives. Estimating energy consumption is complicated by the variability in industrial locomotive types and power ratings, and extreme differences in duty cycles and utilization. Given these limitations, using quantified case study examples and adjustments to standard EPA line-haul and switching duty cycles, bounds on the magnitude of annual US industrial locomotive energy consumption were estimated.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Simutaneous adsorption of CO2 and H2O under Mars-like conditions and application to the evolution of the Martian climate

The Martian regolith is the most substantial volatile reservoir on the planet; estimates of its adsorbed inventory have been based on simple measurements of the adsorption of either water or CO2 in isolation. Under some conditions, H2O can poison adsorbate surfaces, such that CO2 uptake is greatly reduced. We have made the first measurements of the simultaneous adsorption of CO2 and H2O under conditions appropriate to the Martian regolith and have found that at H2O monolayer coverage above about 0.5, CO2 begins to be displaced into the gas phase. We have developed an empirical expression that describes our co-adsorption data and have applied it to standard models of the Martian regolith. We find that currently, H2O does not substantially displace CO2, implying that the adsorbate inventories previously derived may be accurate, not more than 3-4 kPa (30-40 mbar). No substantial increase in atmospheric pressure is predicted at higher obliquities because high-latitude ground ice buffers the partial pressure of H2O in the pores, preventing high monolayer coverages of H2O from displacing CO2. The peak atmospheric pressure at high obliquity does increase as the total inventory of exchangeable CO2 increases.

Zent, Aaron P.↗

Simultaneous adsorption of CO2 and H2O under Mars-like conditions and application to the evolution of the Martian climate

The Martian regolith is the most substantial volatile reservoir on the planet; estimates of its adsorbed inventory have been based on simple measurements of the adsorption of either water or CO2 in isolation. Under some conditions, H2O can poison adsorbate surfaces, such that CO2 uptake is greatly reduced. We have made the first measurements of the simultaneous adsorption of CO2 and H2O under conditions appropriate to the Martian regolith and have found that at H2O monolayer coverage above about 0.5, CO2 begins to be displaced into the gas phase. We have developed an empirical expression that describes our co-adsorption data and have applied it to standard models of the Martian regolith. We find that currently, H2O does not substantially displace CO, implying that the adsorbate inventories previously derived may be accurate, not more than 3-4 kPa (30-40 mbar). No substantial increase in atmospheric pressure is predicted at higher obliquities because high-latitude ground ice buffers the partial pressure of H2O in the pores, preventing high monolayer coverages of H2O from displacing CO2. The peak atmospheric pressure at high obliquity does increase as the total inventory of exchangeable CO2 increases.

Zent, Aaron, P.↗

Design and Impacts of Land-Biogenic-Atmosphere Coupling in the NASA-Unified WRF (NU-WRF) Modeling System

Land-Atmosphere coupling is typically designed and implemented independently for physical (e.g. water and energy) and chemical (e.g. biogenic emissions and surface depositions)-based models and applications. Differences in scale, data requirements, and physics thus limit the ability of Earth System models to be fully coupled in a consistent manner. In order for the physical-chemical-biological coupling to be complete, treatment of the land in terms of surface classification, condition, fluxes, and emissions must be considered simultaneously and coherently across all components. In this study, we investigate a coupling strategy for the NASA-Unified Weather Research and Forecasting (NU-WRF) model that incorporates the traditionally disparate fluxes of water and energy through NASA's LIS (Land Information System) and biogenic emissions through BEIS (Biogenic Emissions Inventory System) and MEGAN (Model of Emissions of Gases and Aerosols from Nature) into the atmosphere. In doing so, inconsistencies across model inputs and parameter data are resolved such that the emissions from a particular plant species are consistent with the heat and moisture fluxes calculated for that land cover type. In turn, the response of the atmospheric turbulence and mixing in the planetary boundary layer (PBL) acts on the identical surface type, fluxes, and emissions for each. In addition, the coupling of dust emission within the NU-WRF system is performed in order to ensure consistency and to maximize the benefit of high-resolution land representation in LIS. The impacts of those self-consistent components on' the simulation of atmospheric aerosols are then evaluated through the WRF-Chem-GOCART (Goddard Chemistry Aerosol Radiation and Transport) model. Overall, this ambitious project highlights the current difficulties and future potential of fully coupled. components. in Earth System models, and underscores the importance of the iLEAPS community in supporting improved knowledge of processes and innovative approaches for models and observations.

Tan, Qian↗

Alternative stable states of the forest mycobiome are maintained through positive feedbacks

Most trees on Earth form a symbiosis with either arbuscular mycorrhizal or ectomycorrhizal fungi. By forming common mycorrhizal networks, actively modifying the soil environment and other ecological mechanisms, these contrasting symbioses may generate positive feedbacks that favour their own mycorrhizal strategy (that is, the con-mycorrhizal strategy) at the expense of the alternative strategy. Positive con-mycorrhizal feedbacks set the stage for alternative stable states of forests and their fungi, where the presence of different forest mycorrhizal strategies is determined not only by external environmental conditions but also mycorrhiza-mediated feedbacks embedded within the forest ecosystem. Here, in this work, we test this hypothesis using thousands of US forest inventory sites to show that arbuscular and ectomycorrhizal tree recruitment and survival exhibit positive con-mycorrhizal density dependence. Data-driven simulations show that these positive feedbacks are sufficient in magnitude to generate and maintain alternative stable states of the forest mycobiome. Given the links between forest mycorrhizal strategy and carbon sequestration potential, the presence of mycorrhizal-mediated alternative stable states affects how we forecast forest composition, carbon sequestration and terrestrial climate feedbacks.

54 ENVIRONMENTAL SCIENCES↗

2000 The Twin Cities Metropolitan Area Travel Behavior Inventory

The 2000 Twin Cities Metropolitan Area Travel Behavior Inventory, conducted by Twin Cities Metropolitan Council—Saint Paul, was the first major travel survey in the region since 1990. The 2000 inventory includes a home interview survey, an establishment survey, a transit survey, external station traffic counts, and an external station origin/destination survey. The study area under the household inventory survey included the seven counties of the regional Metropolitan Planning Organization and thirteen adjacent counties. Demographic, socioeconomic, and travel data were gathered for 6,386 households. Of these, 6,219 households completed the travel logs, which includes household members older than five years old.

1Hz data↗

INTERFUEL: FAST -- Fueling Center and EVSE Reporting Process Changes

This presentation presents an overview of coming changes to how federal agencies with motor vehicles will submit required information about fueling centers and electric vehicle supply equipment (EVSE) inventory through the Federal Automotive Statistical Tool (FAST). Historically, information covering these two areas has been provide during two separate data submissions, but is now being consolidated and simplified into a single submission due by December 15 of each year. The presentation provides background on the process, a re-cap of how the information is currently submitted, and describes the new approach for organizations to submit the required information. This presentation is intended for delivery via WebEx/GoToMeeting at the July 8, 2020 meeting of the DOE-sponsored INTERFUEL working group. FAST is a web-based information management tool developed by INL and funded by GSA's Office of Government-wide Policy and DOE's Federal Energy Management Program.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

PIPII cryoplant non thermal cycling updates

The Proton Improvement Plan-II (PIP-II) is a crucial upgrade to the Fermilab accelerator complex, featuring a new 800-MeV Superconducting Radio-Frequency (SRF) linear accelerator (LINAC) with 23 cryomodules operating at 2K. The LINAC thermohydraulic conditions are satisfied by the cryogenic subsystems: Cryogenic Distribution System (CDS), a helium refrigerator cold box (CB), a warm compression station (WCS) and a helium recovery system (RSYS). The accelerator has a strict requirement of non-thermal cycling of the LINAC cryomodules during planned and unplanned subsystem outages. This paper presents an integrated operating modes analysis of the of the LINAC/CDS thermohydraulic loads satisfied by the CB/WCS cooling system supported by the RSYS inventory management system. The study is based on latest cryoplant and CDS engineering deliverables, as well as the recent performance data from single cryomodule qualification tests performed at the Fermilab PIP-II Injector Test test s tand. The study evaluates both normal and abnormal operating modes, with a focus on identifying integrated scenarios that put subsystems components under stress. The conclusions of this study will help build redundancy to reduce the risk of thermal cycles during planned and unplanned subsystem outages.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nuclear Data Impact on Key Metrics for a Representative Molten Chloride Fast Reactor Model

Nuclear data are an essential component of the foundation on which all modeling and simulation methods and tools are relying upon, from the front end to the back end of the nuclear fuel cycle. In this study, the impact of uncertainties in nuclear data is investigated for a representative molten chloride fast reactor, for several important metrics, including eigenvalue, reactivity differences, and nuclide inventories in fuel at 5-yr irradiation. Uncertainty of keff for a full core model was found to be similar between the fresh fuel and the irradiated fuel states (1.7-1.8%), with its primary driver being the uncertainty in the 235U (n,γ) cross section. The results obtained for the reactivity differences show large uncertainties, of over 100%, in elastic scattering sensitivities of several nuclides, which led to large uncertainties of temperature reactivity differences for cladding and reflector. These results provide evidence that the currently applied methods may not be sufficiently adequate for ensuring the reliable determination of such metrics.

Procop, Germina [ORNL] (ORCID:0000000342226393)↗

Central Atlantic regional ecological test site

The work of the Central Atlantic Regional Ecological Test Site (CARETS) project is discussed. The primary aim of CARETS is to test the hypothesis that data from ERTS-A can be made an integral part of a regional land resources information system, encompassing both inventory of the resource base and monitoring of changes, along with their effects on the quality of the environment. Another objective of the project is to determine scaling factors for developing land use information and regional analysis for regions of any given size.

Alexander, R. H.↗

A summary of ERTS data applications in Alaska

ERTS has proven to be an exceedingly useful tool for the preparation of urgently needed resource surveys in Alaska. For this reason the wide utilization of ERTS data by federal, state and industrial agencies in Alaska is increasingly directed toward the solution of operational problems in resource inventories, environmental surveys, and land use planning. Examples of some applications are discussed in connection with surveys of potential agricultural lands; mapping of predicted archaeological sites; permafrost terrain and aufeis mapping; snow melt enhancement from Prudhoe Bay roads; geologic interpretations correlated ith possible new petroleum fields, with earthquake activity, and with plate tectonic motion along the Denali fault system; hydrology in monitoring surging glaciers and the break-up characteristics of the Chena River watershed; sea-ice morphology correlated with marine mammal distribution; and coastal sediment plume circulation patterns.

Miller, J. M.↗