Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “control simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Non-linear controls influence functions in an aircraft dynamics simulator

In the development and testing of novel structural and controls concepts, such as morphing aircraft wings, appropriate models are needed for proper system characterization. In most instances, available system models do not provide the required additional degrees of freedom for morphing structures but may be modified to some extent to achieve a compatible system. The objective of this study is to apply wind tunnel data collected for an Unmanned Air Vehicle (UAV), that implements trailing edge morphing, to create a non-linear dynamics simulator, using well defined rigid body equations of motion, where the aircraft stability derivatives change with control deflection. An analysis of this wind tunnel data, using data extraction algorithms, was performed to determine the reference aerodynamic force and moment coefficients for the aircraft. Further, non-linear influence functions were obtained for each of the aircraft s control surfaces, including the sixteen trailing edge flap segments. These non-linear controls influence functions are applied to the aircraft dynamics to produce deflection-dependent aircraft stability derivatives in a non-linear dynamics simulator. Time domain analysis of the aircraft motion, trajectory, and state histories can be performed using these nonlinear dynamics and may be visualized using a 3-dimensional aircraft model. Linear system models can be extracted to facilitate frequency domain analysis of the system and for control law development. The results of this study are useful in similar projects where trailing edge morphing is employed and will be instrumental in the University of Maryland s continuing study of active wing load control.

Guerreiro, Nelson M.↗
NASA NTRS2012

Intelligent Systems Approach for Automated Identification of Individual Control Behavior of a Human Operator

Results have been obtained using conventional techniques to model the generic human operator?s control behavior, however little research has been done to identify an individual based on control behavior. The hypothesis investigated is that different operators exhibit different control behavior when performing a given control task. Two enhancements to existing human operator models, which allow personalization of the modeled control behavior, are presented. One enhancement accounts for the testing control signals, which are introduced by an operator for more accurate control of the system and/or to adjust the control strategy. This uses the Artificial Neural Network which can be fine-tuned to model the testing control. Another enhancement takes the form of an equiripple filter which conditions the control system power spectrum. A novel automated parameter identification technique was developed to facilitate the identification process of the parameters of the selected models. This utilizes a Genetic Algorithm based optimization engine called the Bit-Climbing Algorithm. Enhancements were validated using experimental data obtained from three different sources: the Manual Control Laboratory software experiments, Unmanned Aerial Vehicle simulation, and NASA Langley Research Center Visual Motion Simulator studies. This manuscript also addresses applying human operator models to evaluate the effectiveness of motion feedback when simulating actual pilot control behavior in a flight simulator.

Zaychik, Kirill B.↗
NASA NTRS2004

Addressing Control Research Issues Leading to Piloted Simulations in Support of the IFCS F-15

This report summarizes the research effort by a team of researchers at West Virginia University in support of the NASA Intelligent Flight Control System (IFCS) F-15 program. In particular, WVU researchers assisted NASA Dryden researchers in the following technical tasks leading to piloted simulation of the 'Gen_2' IFCS control laws. Task #1- Performance comparison of different neural network (NN) augmentation for the Dynamic Inversion (DI) -based VCAS 'Gen_2' control laws. Task #2- Development of safety monitor criteria for transition to research control laws with and without failure during flight test. Task #3- Fine-tuning of the 'Gen_2' control laws for cross-coupling reduction at post-failure conditions. Matlab/Simulink-based simulation codes were provided to the technical monitor on a regular basis throughout the duration of the project. Additional deliverables for the project were Power Point-based slides prepared for different project meetings. This document provides a description of the methodology and discusses the general conclusions from the simulation results.

Napolitano, Marcello↗
NASA NTRS1986

Flight training for Space Shuttle missions

The training performed for flights of the Space Shuttle is intensive and extremely complicated. The training is totally dependent on computer generated training situations in both cockpit simulations and in integrated simulations between the simulators and the Mission Control Center (MCC). These simulations form a complex set of dress rehearsals of the actual spaceflight allowing the participants to address problems in a real world situation and utilize problem solving rationale just as they will be called upon to do during the real flight. The benefits of this type of training have been demonstrated during the flights of the Shuttle as individual flight controllers and whole teams have been tested by various untoward situations. This system of integrated simulation and training, more complex than ever, will be continued in use in the future using even more intricate man-machine interactions required to initialize, control, and operate it.

Hughes, F. E.↗
NASA NTRS1991

Designing low bandwidth propulsive-only flight controllers

Results from an investigation of using engine commands to control flight attitude are described. In-flight operation with simulated failed flight controls is reviewed and ground simulations of piloted propulsive-only control to touchdown are analyzed. A design of an optimal control law to assist the pilot is presented. Recommendations are made for more robust design and implementation. Results to date indicate that simple and effective augmented control can be achieved in a wide variety of failed configurations.

Biezad, Daniel J.↗
NASA NTRS1996

Designing Low Bandwidth Propulsive-Only Flight Controllers

Results from an investigation of using engine commands to control flight attitude are described. In-flight operation with simulated failed flight controls is reviewed and ground simulations of piloted propulsive-only control to touchdown are analyzed. A design of an optimal control law to assist the pilot is presented. Recommendations are made for more robust design and implementation. Results to date indicate that simply and effective augmented control can be achieved in a wide variety of failed configurations.

Biezad, Daniel J.↗
NASA NTRS2015

Automated Cooperative Trajectories

This presentation is an overview of the Automated Cooperative Trajectories project. An introduction to the phenomena of wake vortices is given, along with a summary of past research into the possibility of extracting energy from the wake by flying close parallel trajectories. Challenges and barriers to adoption of civilian automatic wake surfing technology are identified. A hardware-in-the-loop simulation is described that will support future research. Finally, a roadmap for future research and technology transition is proposed.

fuel comsumption↗
NASA NTRS2014

UAS Measured Response: The Effect of GCS Control Mode Interfaces on Pilot Ability to Comply with ATC Clearances

The present study examines the effects of three different control mode interfaces on unmanned aerial system (UAS) pilots ability to comply with air traffic controller traffic clearances. Pilots controlled a simulated UAS with a waypoint-only interface, an auto-pilot interface and a manual, stick and throttle interface. Results indicate that pilots are best able to get in-the-loop when provided with auto-pilot and manual control inputs. Limitations to the present study and future analyses are discussed.

Measured Response↗
NASA NTRS1995

Computer-Controlled Movable Spotlight

Spotlight simulates reduced solar illumination at changing angles of incidence. Different from typical solar simulators in that light source mobile, controlled, and calibrated, while illuminated environment stationary. Computer-controlled movable spotlight resembles ordinary spotlight, but translated, tilted, and focused (brightness controlled) by computerized control system to obtain effect of sunlight with reduced but constant intensity, with slowly varying angles of incidence.

Volpe, Richard↗
NASA NTRS2012

ISRU Soil Mechanics Vacuum Facility: Soil Bin Preparation and Simulant Strength Characterization

Testing in relevant environments is key to exploration mission hardware development. This is true on both the component level (in early development) and system level (in late development stages). During ISRU missions the hardware will interface with the soil (digging, roving, etc) in a vacuum environment. A relevant test environment will therefore involve a vacuum chamber with a controlled, conditioned simulant bed. However, in earth-based granular media, such as lunar soil simulant, gases trapped within the material pore structures and water adsorbed to all particle surfaces will release when exposed to vacuum. Early vacuum testing has shown that this gas release can occur violently, which loosens and weakens the simulant, altering the consolidation state. The Vacuum Facility #13, a mid-size chamber (3.66m tall, 1.5m inner diameter) at the NASA Glenn Research Center has been modified to create a soil mechanics test facility. A 0.64m deep by 0.914m square metric ton bed of lunar simulant was placed under vacuum using a variety of pumping techniques. Both GRC-3 and LHT-3M simulant types have been used. An electric cone penetrometer was used to measure simulant strength properties at vacuum including: cohesion, friction angle, bulk density and shear modulus. Simulant disruptions, caused by off gassing, affected the strength properties, but could be mitigated by reducing pump rate. No disruptions were observed at pressures below 2.5Torr, regardless of the pump rate. However, slow off gassing of the soil lead to long test times, a full week, to reach 10-5Torr. This work highlights the need for robotic machine-simulant hardware and operations in vacuum to expeditiously perform (sub-)systems tests.

Kleinhenz, Julie↗
NASA NTRS2021

Between-Simulator Comparison of Motion Filter Order and Break Frequency Interaction Effects on Pilot Control Behavior

This paper investigates the interaction effects of motion filter order and break frequency on pilots' manual control behavior and control performance using two simulators. Eighteen pilots performed the experiment in the Vertical Motion Simulator (VMS) at NASA Ames Research Center and twenty pilots in the SIMONA Research Simulator at Delft University of Technology. The experiment used a full-factorial design with three motion filter orders (first-, second-, and third-order) and two filter break frequencies (0.5 and 2.0 rad/s), in addition to reference no-motion and full-motion conditions. Key task variables, such as the quality of the motion and visual cues and the characteristics of the sidestick, were matched across both simulators. Overall, the expected effects of filter order and break frequency variations were found, with both increasing order and increasing break frequency causing pilots to use less motion feedback in their control strategy, resulting in lower tracking performance. Furthermore, across the wide range of filter orders tested in the experiment, the existing Sinacori-Schroeder motion fidelity criterion was found to be a good predictor of the interaction effects of both filter settings on pilot control behavior. For the same motion condition, there was a consistent offset in the results between simulators, due to the more high-gain control strategy adopted by a number of the VMS pilots. Still, the observed relative trends in pilot control behavior and performance between motion conditions were equivalent in both simulators and thus accurately replicated.

manual control↗
NASA NTRS2016

Vibration Control via Stiffness Switching of Magnetostrictive Transducers

In this paper, a computational study is presented of structural vibration control that is realized by switching a magnetostrictive transducer between high and low stiffness states. Switching is accomplished by either changing the applied magnetic field with a voltage excitation or changing the shunt impedance on the transducer's coil (i.e., the magnetostrictive material's magnetic boundary condition). Switched-stiffness vibration control is simulated using a lumped mass supported by a damper and the magnetostrictive transducer (mount), which is represented by a nonlinear, electromechanical model. Free vibration of the mass is calculated while varying the mount's stiffness according to a reference switched-stiffness vibration control law. The results reveal that switching the magnetic field produces the desired change in stiffness, but also an undesired actuation force that can significantly degrade the vibration control. Hence, a modified switched-stiffness control law that accounts for the actuation force is proposed and implemented for voltage-controlled stiffness switching. The influence of the magneto-mechanical bias condition is also discussed. Voltage-controlled stiffness switching is found to introduce damping equivalent to a viscous damping factor up to about 0.13; this is shown to primarily result from active vibration reduction caused by the actuation force. The merit of magnetostrictive switched-stiffness vibration control is then quantified by comparing the results of voltage- and shunt-controlled stiffness switching to the performance of optimal magnetostrictive shunt damping. For the cases considered, optimal resistive shunt damping performed considerably better than both voltage- and shunt-controlled stiffness switching.

vibration control↗
NASA NTRS2016

Vibration Control via Stiffness Switching of Magnetostrictive Transducers

This paper presents a computational study of structural vibration control that is realized by switching a magnetostrictive transducer between high and low stiffness states. Switching is accomplished by either changing the applied magnetic field with a voltage excitation or changing the shunt impedance on the transducer's coil (i.e., the magnetostrictive material's magnetic boundary condition). Switched-stiffness vibration control is simulated using a lumped mass supported by a damper and the magnetostrictive transducer (mount), which is represented by a nonlinear, electromechanical model. Free vibration of the mass is calculated while varying the mount's stiffness according to a reference switched-stiffness vibration control law. The results reveal that switching the magnetic field produces the desired change in stiffness, but also an undesired actuation force that can significantly degrade the vibration control. Hence, a modified switched-stiffness control law that accounts for the actuation force is proposed and implemented for voltage-controlled stiffness switching. The influence of the magnetomechanical bias condition is also discussed. Voltage-controlled stiffness switching is found to introduce damping equivalent to a viscous damping factor up to about 0.25; this is shown to primarily result from active vibration reduction caused by the actuation force. The merit of magnetostrictive switched-stiffness vibration control is then quantified by comparing the results of voltage- and shunt-controlled stiffness switching to the performance of optimal magnetostrictive shunt damping.

stiffness tuning↗
NASA NTRSDate not supplied

Developing Urban Air Mobility Vehicle Models to Support Air Traffic Management Concept Development

To support Urban Air Mobility (UAM) research efforts at NASA, the Airspace Target Generator (ATG) software used in the FutureFlight Central (FFC) air traffic control tower simulator is undergoing updates to support physics-based UAM vehicle models. A process was developed to integrate UAM vertical takeoff and landing (VTOL) aircraft into the fixed-wing ATG modeling environment without significant change to the underlying equations of motion and vehicle model database. The VTOL aircraft models were converted from a six degrees-of-freedom (6-DOF) representation into a four degrees-of-freedom (4-DOF) representation for integration within ATG. Three vehicle designs from the NASA Revolutionary Vertical-Lift Technologies (RVLT) project were selected: a lift-plus-cruise (LPC) aircraft model and quadrotor, electric-powered (QEP) 1-seater and 6-seater models. With the LPC model comprised of a nonlinear force and moment build-up, and the QEP models comprised of linearized stability derivatives, two separate processes were developed to convert the lift, drag, and propulsion characteristics of each model into the ATG model database. Key aircraft performance characteristics including climb, cruise, and descent performance were preserved during the conversion process. Because ATG simulates fixed-wing aircraft through ground taxi and takeoff to approach and landing, acceleration command algorithms were developed to model the vertical takeoff and vertical landing phase of UAM operations. A strategy was then developed to transition the aircraft model to- and from- the new control mode.

urban air mobility↗
NASA NTRS1979

Systems development of a stall/spin research facility using remotely controlled/augmented aircraft models. Volume 1: Systems overview

A ground based, general purpose, real time, digital control system simulator (CSS) is specified, developed, and integrated with the existing instrumentation van of the testing facility. This CSS is built around a PDP-11/55, and its operational software was developed to meet the dual goal of providing the immediate capability to represent the F-18 drop model control laws and the flexibility for expansion to represent more complex control laws typical of control configured vehicles. Overviews of the two CSS's developed are reviewed as well as the overall system after their integration with the existing facility. Also the latest version of the F-18 drop model control laws (REV D) is described and the changes needed for its incorporation in the digital and analog CSS's are discussed.

Montoya, R. J.↗
NASA NTRS1992

System for Anomaly and Failure Detection (SAFD) system development

This task specified developing the hardware and software necessary to implement the System for Anomaly and Failure Detection (SAFD) algorithm, developed under Technology Test Bed (TTB) Task 21, on the TTB engine stand. This effort involved building two units; one unit to be installed in the Block II Space Shuttle Main Engine (SSME) Hardware Simulation Lab (HSL) at Marshall Space Flight Center (MSFC), and one unit to be installed at the TTB engine stand. Rocketdyne personnel from the HSL performed the task. The SAFD algorithm was developed as an improvement over the current redline system used in the Space Shuttle Main Engine Controller (SSMEC). Simulation tests and execution against previous hot fire tests demonstrated that the SAFD algorithm can detect engine failure as much as tens of seconds before the redline system recognized the failure. Although the current algorithm only operates during steady state conditions (engine not throttling), work is underway to expand the algorithm to work during transient condition.

Oreilly, D.↗
NASA NTRS1982

An experimental study of human pilot's scanning behavior

The scanning behavior and the control behavior of the pilot who manually controls the two-variable system, which is the most basic one of multi-variable systems are investigated. Two control tasks which simulate the actual airplane attitude and airspeed control were set up. In order to simulate the change of the situation where the pilot is placed, such as changes of flight phase, mission and others, the subject was requested to vary the weightings, as his control strategy, upon each task. Changes of human control dynamics and his canning properties caused by the modification of the situation were investigated. By making use of the experimental results, the optimal model of the control behavior and the scanning behavior of the pilot in the two-variable system is proposed from the standpoint of making the performance index minimal.

Washizu, K.↗