SEARCH · Engineering Papers

Results for “content”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Uniaxial stress increases layer stacking disorder in calcium silicate hydrates with low calcium content

The long-term stress response of concrete is controlled by the intergrain and intragrain interactions of calcium-silicate-hydrates (C-S-H), nanocrystalline forms of tobermorites. To investigate both types of interactions, we examined the deviatoric stress response of 11 Å tobermorite powder with X-ray diffraction, finding that its layer stacking (i.e., sliding) disorder significantly increases. A similar experiment was performed on nanocrystalline C-S-H powders before and after applying a 360 MPa uniaxial stress. Layer stacking disorder (in the form of intragrain deformation) increases when there is low water content and when the basal spacing is large. We also find that grains with a smaller thickness-to-diameter aspect ratio are first to develop preferred orientation (in the form of intergrain sliding), facilitated by gel water. Furthermore, these findings show that intragrain deformations in C-S-H can occur at relatively low stresses and provide insights into the creep mechanism of C-S-H.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Incorporating leaf chlorophyll content into a two-leaf terrestrial biosphere model for estimating carbon and water fluxes at a forest site

Chlorophyll is the main light-harvesting pigment in leaves, facilitating photosynthesis and indicating the supply of nitrogen for photosynthetic enzymes. In this study, we explore the feasibility of integrating leaf chlorophyll content (Chl leaf ) into a Terrestrial Biosphere Model (TBM), as a proxy for the leaf maximum carboxylation rate at 25 °C (V$_{max}^{25}$), for the purpose of improving carbon and water flux estimation. Measurements of Chl leaf and V$_{max}^{25}$ were made in a deciduous forest stand at the Borden Forest Research Station in southern Ontario, Canada, where carbon and water fluxes were measured by the eddy covariance method. The use of Chl leaf -based V$_{max}^{25}$ in the TBM significantly reduces the bias of estimated gross primary productivity (GPP) and evapotranspiration (ET) and improves the temporal correlations between the simulated and the measured fluxes, relative to the commonly employed cases of using specified constant V$_{max}^{25}$, leaf area index (LAI)-based V$_{max}^{25}$ or specific leaf area (SLA)-based V$_{max}^{25}$. The biggest improvements are found in spring and fall, when the mean absolute errors (MAEs) between modelled and measured GPP are reduced from between 2.2–3.2 to 1.8 g C m -2 d -1 in spring and from between 2.1–2.8 to 1.8 g C m -2 d -1 in fall. The MAEs in ET estimates are reduced from 0.7–0.8 mm d -1 to 0.6 mm d -1 in spring, but no significant improvement is noted in autumn. A two-leaf upscaling scheme is used to account for the uneven distribution of incoming solar radiation inside canopies and the associated physiological differences between leaves. We found that modelled V$_{max}^{25}$ in sunlit leaves is 34% larger than in the shaded leaves of the same Chl leaf , which echoes previous physiological studies on light acclimation of plants. This study represents the first case of the incorporation of chlorophyll as a proxy for V$_{max}^{25}$ in a two-leaf TBM at a forest stand and demonstrates the efficacy of using chlorophyll to constrain V$_{max}^{25}$ and reduce the uncertainties in GPP and ET simulations.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

Overexpression of NblA decreases phycobilisome content and enhances photosynthetic growth of the cyanobacterium Synechococcus elongatus PCC 7942

Many research groups have considered whether decreasing photosynthetic antenna content in cyanobacteria can improve photosynthetic oxygen evolution and biomass accumulation. In this work, we describe a genetic strategy for truncating light harvesting antennae based on engineered alterations in the expression of NblA, a native protein naturally used by cyanobacteria to disassemble phycobilisomes antennae in response to environmental changes. We show that if enforced overexpression is fine-tuned, it is possible to realize gains in photosynthesis in a model cyanobacterium Synechococcus elongatus PCC 7942. We also show that antennae truncation helps protect cells from photodamage and that a strain overexpressing NblA can outcompete wild type in a mixed population. We propose approaches for future applications of these findings.

09 BIOMASS FUELS↗

DOE OSTI2017

Determining the minimum required uranium carbide content for HTGR UCO fuel kernels

There are three important failure mechanisms that must be controlled in high-temperature gas-cooled reactor (HTGR) fuel for certain higher burnup applications are SiC layer rupture, SiC corrosion by CO, and coating compromise from kernel migration. All are related to high CO pressures stemming from free O generated when uranium present as UO 2 fissions and the O is not subsequently bound by other elements. Furthermore, in the HTGR UCO kernel design, CO buildup from excess O is controlled by the inclusion of additional uranium in the form of a carbide, UC x . An approach for determining the minimum UC x content to ensure negligible CO formation was developed and demonstrated using CALPHAD models and the Serpent 2 reactor physics and depletion analysis tool. Our results are intended to be more accurate than previous estimates by including more nuclear and chemical factors, in particular the effect of transmutation products on the oxygen distribution as the fuel kernel composition evolves with burnup.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

Multi-atom Pt and PtRu catalysts for high performance AEMFCs with ultra-low PGM content

To reduce the platinum group metal (PGM) loading in anion exchange membrane fuel cells (AEMFCs), it is important to transition to catalysts with very low PGM content, and eventually to catalysts that are completely PGM-free. Here, in this work, four supported low-PGM Pt and PtRu catalysts were prepared using a new, simple, scalable technique: Controlled Surface Tension (CST) method. CST allows for a high density of very small multi-atom clusters. Catalysts were physically characterized using a wide array of techniques and tested for their ORR and HOR activity both ex-situ and integrated into operating AEMFCs. The PGM loading was reduced by a factor of 14 while achieving comparable performance to commercial catalysts. AEMFCs were also assembled with ultralow PGM loading (0.05 mgPGM cm -2 ), where PtRu anodes were paired with Fe–N–C cathodes to achieve a specific power of 25 W/mg PGM (40 W/mg Pt ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2016

Effect of aging on lignin content, composition and enzymatic saccharification in Corymbia hybrids and parental taxa between years 9 and 12

Corymbia (a eucalypt) is an important forestry genus and a potential lignocellulosic bioenergy feedstock. The composition of the lignocellulosic cell wall significantly impacts pretreatment efficiency and conversion to biofuel but is variable and changes with age. In this study, we estimated Klason lignin content, composition, and monosaccharide (glucose and xylose) release after enzymatic saccharification of untreated and hydrothermally pretreated biomass from Corymbia parental species Corymbia torelliana (CT), Corymbia citriodora subsp. variegata (spotted gum; CCV), and interspecific F1 hybrids (CT x CCV) at ages 9 and 12 years from planting. Analysis of lignin composition derived from syringyl/guaiacyl monolignols (S/G) found significant differences among taxa, with CT S/G ratios (2.2 and 2.0) being significantly lower than CCV (2.6 and 2.3) or hybrids (2.5 and 2.3) at ages 9 and 12 respectively. In general, enzymatic saccharification yields from untreated biomass were significantly different among taxa, with CT (113 and 75 mg g -1 ) and hybrids (108 and 81 mg g -1 ) yielding significantly higher glucose from untreated biomass than CCV (82 and 56 mg g -1 ) at ages 9 and 12 respectively. Comparison of traits within taxa between ages 9 and 12 found S/G ratios and glucose yields from untreated biomass were significantly lower in CT, CCV and hybrid taxa. As a result, the formation of lignocellulosic cell walls is complex, influenced by genetics and age of material, requiring optimization of rotation age for biofuel production and other industrial processes.

09 BIOMASS FUELS↗

DOE OSTI2013

Micro- and meso-scale pore structure in mortar in relation to aggregate content

Mortar is often viewed as a three-phase composite consisting of aggregate, bulk paste, and an interfacial transition zone (ITZ). However, this description is inconsistent with experimental findings because of the basic assumption that larger pores are only present within the ITZ. In this paper, we use backscattered electron (BSE) imaging to investigate the micro- and meso-scale structure of mortar with varying aggregate content. The results indicate that larger pores are present not only within the ITZ but also within areas far from aggregates. This phenomenon is discussed in detail based on a series of analytical calculations, such as the effective water binder ratio and the inter-aggregate spacing. We developed a modified computer model that includes a two-phase structure for bulk paste. This model interprets previous mercury intrusion porosimetry data very well. -- Highlights: •Based on BSE, we examine the HCSS model. •We develop the HCSS-DBLB model. •We use the modified model to interpret the MIP data.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Chloride diffusivity, chloride threshold, and corrosion initiation in reinforced alkali-activated mortars: Role of calcium, alkali, and silicate content

The aim of this study is to investigate systematically the chloride diffusivity and chloride threshold of a wide range of calcium-rich and fly ash-dominated alkali-activated samples in light of their compositional differences. To this end, the effects of various fly ash (FA)-to-slag ratios, of alkali concentrations and of silicate content in the activator were investigated. The electrochemical aspects of the passive samples were also assessed. Results show the prominent role of calcium in the matrix to reduce the chloride diffusivity. While higher alkali concentration increased the porosity and chloride diffusivities in general, lower modulus ratios provided considerably better performance in the FA-dominated samples. Chloride threshold values range between 0.19 (wt% binder mass) for calcium-rich mortars fabricated at low levels of alkalinities and 0.69 for FA-dominated mortars fabricated with highly alkaline activators. Half-cell potential and polarization resistance of alkali-activated samples were in general lower than their Portland cement counterparts.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content

3D printing with cementitious materials is an emerging technology and provides an active area of research. Despite this, there are only limited studies that examine the pumping behaviour of high yield stress fluids such as printable concrete. We present a study on the rheological behaviour of 3D printable cementitious materials with different aggregate-to-binder ratios (a/b) and analyse the pumping and printing characteristics with the measured rheological parameters. We observed that an increase in a/b resulted in a significant increase of plastic viscosity, and a nominal increase in yield stress and storage modulus. The variation in plastic viscosity and yield stress with increasing aggregate content was analysed with the Krieger-Dougherty and Chateau-Ovarlez-Trung model, respectively. Also, the rheological properties of the paste rich lubrication layer during pumping were determined with the help of a tribometer. The yield stress and viscous constant of the lubrication layer increase with the increase in a/b. The pumping pressure predictions were carried out by a suitable theoretical model by considering appropriate flow conditions for different mixtures. The variation in critical height of printed elements with an increase in a/b was correlated with the observed rheological parameters.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Measure this, not that: Optimizing the cost and model-based information content of measurements

Model-based design of experiments (MBDoE) is a powerful framework for selecting and calibrating science-based mathematical models from data. Here, this work extends popular MBDoE workflows by proposing a convex mixed integer (non)linear programming (MINLP) to optimize the selection of measurements. The solver MindtPy is modified to support calculating the D-optimality objective and its gradient via an external package, scipy, using the grey-box module in Pyomo. The new approach is demonstrated in two case studies: estimating highly correlated kinetics from a batch reactor and estimating transport parameters in a large-scale rotary packed bed for CO 2 capture. Both case studies show how examining the Pareto optimal trade-offs between information content measured by A- and D-optimality versus measurement budget offers practical guidance for selecting measurements for scientific experiments.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2015

Size-segregated emissions and metal content of vehicle-emitted particles as a function of mileage: Implications to population exposure

The study aims at investigating the characteristics (size distribution, active surface and metal content) of particles emitted by cars as a function of mileage using a novel methodology for characterizing particulate emissions captured by Exhaust Gas Suspension (EGS). EGS was obtained by passing the exhaust gases through a container of deionized water. EGS analysis was performed using laser granulometry, electron scanning microscopy, and high resolution mass spectrometry. Implications of the differences in key features of the emitted particles on population exposure were investigated using numerical simulation for estimating size-segregated PM deposition across human respiratory tract (HRT). It was found that vehicle mileage, age and the respective emissions class have almost no effect on the size distribution of the exhaust gas particulate released into the environment; about half of the examined vehicles with low mileage were found to release particles of aerodynamic diameter above 10 μm. The exhaust gas particulate detected in the EGS of all cars can be classified into three major size classes: (1) 0.1–5 µm – soot and ash particles, metals (Au, Pt, Pd, Ir); (2) 10–30 µm – metal (Cr, Fe, Cu, Zr, Ni) and ash particles; (3) 400–1,000 µm – metal (Fe, Cr, Pb) and ash particles. Newer vehicles with low mileage are substantial sources of soot and metal particles with median diameter of 200 nm with a higher surface area (up to 89,871.16 cm{sup 2}/cm{sup 3}). These tend to deposit in the lower part of the human respiratory tract. - Highlights: • Car mileage has virtually no effect on the size of the solid particles released. • Newer diesel vehicles emit particles of lower aerodynamic diameter. • Particle active surface emitted by newer vehicles is on average 3 times higher. • Real-life emissions were translated into actual internal PM exposure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2012

Properties of impurity-bearing ferrihydrite I. Effects of Al content and precipitation rate on the structure of 2-line ferrihydrite

The association of Al with ferrihydrite (Fh) may have a considerable effect on the composition, structure, and surface properties of Fh nanoparticles, and thus impact its reactivity and interaction with pollutant species. Aluminous Fh is abundant in natural environments, but the mode of association of Al with this nanomineral is not yet fully understood. Al{sup 3+} speciation may vary from true chemical substitution for Fe{sup 3+}, to adsorption or surface precipitation, and/or to formation of a mixture of two (or more) individual nanoscale phases. The conditions of formation (i.e. slow vs. rapid precipitation) may also affect the nature of Fh nanoparticles in terms of their crystallinity, phase purity, and Al speciation. In this study we used a variety of laboratory (TEM, NMR, ICP-AES) and synchrotron-based techniques (X-ray total scattering and PDF analysis, scanning transmission X-ray microscopy, Al K-edge XANES spectroscopy) to characterize two synthetic Al-bearing Fh series formed at different precipitation rates in the presence of 5-40 mol% Al. We find that Al is dominantly octahedrally coordinated in the synthetic Fh samples and that up to 20-30 mol% Al substitutes for Fe in the Fh structure, regardless of the synthesis method we used. Formation of separate aluminous phases (e.g., gibbsite) was most significant at Al concentrations above 30 mol% Al in slowly precipitated samples. However, small amounts (<6% of total Al) of Al-hydroxide phases were also detected by NMR spectroscopy in samples with lower Al content (as low as 15 mol% Al), particularly in the Fh series that was precipitated slowly. Furthermore, it appears that the amount of Al incorporated in Fh is not affected by the synthesis methods we used and is more likely controlled by the accumulated strain caused by Al substitution in the Fh lattice. Given the prevalence of naturally occurring aluminous ferrihydrite, assumptions about ferrihydrite reactivity in natural environments should consider the impact of Al substitution on reduction potential, Fe bioavailability, as well as sorption reactions.

58 GEOSCIENCES↗

DOE OSTI2016

Effect of Ti content on the microstructure and mechanical behavior of (Fe 36 Ni 18 Mn 33 Al 13 ) 100–x Ti x high entropy alloys

The microstructure and mechanical properties studies of a series of two-phase f.c.c./B2 (ordered b.c.c.) lamellar-structured, high entropy alloys (HEA) Fe 36 Ni 18 Mn 33 Al 13 Ti x with x up to 6 at. % Ti have been investigated. X-ray microanalysis in a TEM showed that the Ti resided mostly in the B2 phase. The lamellar spacing decreased significantly with increasing Ti content from 1.56 μm for the undoped alloy to 155 nm with an addition of 4 at. % Ti, leading to a sharp increase in room-temperature yield strength,σ y , from 270 MPa to 953 MPa, but with a concomitant decrease in ductility from 22% elongation to 2.3%. Annealing at 1173 K for 20 h greatly increased the lamellar spacing of Fe 36 Ni 18 Mn 33 Al 13 Ti 4 to 577 nm, producing a corresponding decrease in σy to 511 MPa. The yield strengths of all the doped alloys decreased significantly when tensile tested at 973 K with a concomitant increase in ductility due to softening of the B2 phase. The fracture mode changed from cleavage at room temperature to a ductile dimple-type rupture at 973 K. Lastly, the results are discussed in terms of the Hall-Petch-type relationship.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Impact of biomass ash content on biocomposite properties

Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). Furthermore, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0–7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Information content of spatially distributed ground-based measurements for hydrologic-parameter calibration in mixed rain-snow mountain headwaters

Parameters in hydrologic models used in mixed rain-snow regions are often uncertain to calibrate and overfitted on streamflow. To contribute addressing these challenges, we used an algorithm that assesses modeling performances through time (Dynamic Identifiability Analysis) to quantify the information content of spatially distributed ground-based measurements for identifying optimal parameter values in the Precipitation Runoff Modeling System (PRMS) model. Including spatially distributed ground-based measurements in Identifiability Analysis allowed us to unambiguously estimate more parameter values than only using streamflow (seven parameters instead of two out of a pool of thirty-three). Peaks in information gain were obtained when using dew-point temperature to identify precipitation phase-partitioning parameters. Multi-attribute identifiability analysis also yielded optimal parameter values that were temporally less variable than those estimated using streamflow alone. Overall, identifying parameter values using ground-based measurements improved the simulation of key drivers of the surface-water budget, such as air temperature and precipitation-phase partitioning. However, parameters simulating surface-to-subsurface mass fluxes like snow accumulation and melt or evapotranspiration were poorly identified by any attribute and so emerged as key sources of predictive uncertainty for this distributed-parameter hydrologic model. In conclusion, this work demonstrates the value of expanded ground-based measurements for identifying parameters in distributed-parameter hydrologic models and so diagnosing their conceptual uncertainty across the water budget.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Apolipoprotein A5 reduces clearance of VLDL by altering apolipoprotein E content

Apolipoprotein A-V (APOA5) is a critical regulator of circulating triglyceride (TG) levels. Its deletion leads to elevated plasma TG concentrations by altering the metabolism of very low-density lipoprotein (VLDL) particles in vivo. One way APOA5 exerts its effects is through modulation of lipoprotein lipase (LPL) activity, specifically by disrupting inhibitory interactions between LPL and angiopoietin-like proteins (ANGPTLs). However, the impact of APOA5 on VLDL composition and its potential to alter VLDL metabolism in other ways remains poorly understood. To address this, we investigated the influence of APOA5 on the VLDL proteome, LPL activation, and hepatic remnant uptake. Using VLDL from Apoa5 knockout (KO) and wild-type (WT) mice, we found no evidence that APOA5 directly enhances LPL activity in purified or plasma systems. However, VLDL from Apoa5 K mice was cleared significantly more slowly by cultured hepatocytes. Proteomics experiments from two independent laboratories identified consistent depletion of 17 proteins involved in lipoprotein metabolism, inflammation, and immune response in Apoa5 KO VLDL, including APOE and serum amyloid A1 (SAA1). Remarkably, reintroduction of recombinant mouse APOA5 to the KO plasma partially restored the WT VLDL proteome, including APOE, and normalized VLDL uptake by hepatocytes without altering LPL lipolysis. These findings reveal that APOA5 influences hepatic clearance of VLDL remnants by modulating particle composition, particularly APOE content. This study expands the functional scope of APOA5 in TG metabolism and underscores its role in VLDL remodeling and remnant clearance, offering new insights with implications for understanding hypertriglyceridemia and its roles in inflammation and immune response.

LPL↗

DOE OSTI2018

Enhancing workability in sheet production of high silicon content electrical steel through large shear deformation

Enhanced workability, as characterized by the magnitude and heterogeneity of accommodated plastic strains during sheet processing, is demonstrated in high Si content Fe-Si alloys containing 4 and 6.5 wt% Si using two single-step, simple-shear deformation techniques – peeling and large strain extrusion machining (LSEM). The model Fe-Si material system was selected for its intrinsically poor material workability, and well-known applications potential in next-generation electric machines. In a comparative study of the deformation characteristics of the shear processes with conventional rolling, two distinct manifestations of workability are observed. For rolling, the relatively diffuse and unconfined deformation zone geometry leads to cracking at low strains, with sheet structures characterized by extensive deformation twinning and banding. Workpiece pre-heating is required to improve the workability in rolling. In contrast, peeling and LSEM produce continuous sheet at large plastic strains without cracking, the result of more confined deformation geometries that enhances the workability. Peeling, however, results in heterogeneous, shear-banded microstructures, pointing to a second type of workability issue – flow localization – that limits sheet processing. This shear banding is to a large extent facilitated by unrestricted flow at the sheet surface, unavoidable in peeling. With additional confinement of this free surface deformation and appropriately designed deformation zone geometry, LSEM is shown to suppress shear banding, resulting in continuous sheet with homogeneous microstructure. Thus LSEM is shown to produce the greatest enhancement in process workability for producing sheet. In conclusion, these workability findings are explained and discussed based on differences in process mechanics and deformation zone geometry.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Investigation of breakaway corrosion observed during oxide growth in pure and low alloying element content Zr exposed in water at 360°C

The addition of small concentrations of alloying elements to pure zirconium can prevent nuclear fuel cladding material from undergoing unstable oxide growth in aqueous environments at light water reactor operating temperatures. The role of alloying elements in stabilizing the oxide growth is examined in this paper, to better understand the oxide growth stabilization mechanism. To this end, a set of initial, short-duration corrosion experiments were performed, followed by oxide layer characterization. Specifically, ten model Zr alloys were selected to test the effect of small alloying additions on the alloy corrosion rate and corrosion breakaway. Additionally, these alloys were corrosion tested in pure water in an autoclave at 360°C for up to 70 days. The alloys included crystal bar Zr, sponge Zr, and model alloys with small concentrations of Sn, Fe, and Cr. After testing, the alloys were characterized using scanning electron microscopy (SEM) and synchrotron µ-X-ray fluorescence (µXRF) to study how the structure of the oxide and alloying element distribution related to unstable oxide growth. Initial results in the 360°C water environment showed breakaway oxidation may be caused by unstable oxide growth due to heterogeneous distribution of the alloying elements. Heterogeneous distribution of alloying elements was correlated to the occurrence of unstable oxide growth (either nodule-like, grain boundary penetration, or differential grain-to-grain growth). It is possible that this heterogeneity, made possible by low alloying element content, can cause breakaway corrosion, but further study is warranted.

36 MATERIALS SCIENCE↗