Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “appendix”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Development of Grade 91 inelastic model for incorporation in ASME Division 5

This report describes a unified viscoplastic model for Grade 91 suitable for use with the Section III, Division 5 design by inelastic analysis procedures in the ASME Boiler and Pressure Vessel Code. The report identifies several key features a successful design inelastic model must capture along with critical aspects of the response of Grade 91 for elevated temperature loading conditions typical of expected reactor operating conditions. An inelastic model for Code design must capture the average response of a material including heat-to-heat and product form variations. This work develops a method for calibrating such a model to a large experimental database using genetic algorithm optimization. Finally, the report compares the final model to several specialized experimental tests to validate that it will be suitable for use in high temperature structural design. The techniques developed here can be applied to the remaining Section III, Division 5, Class A materials to develop a nonmandatory appendix to the Code describing inelastic material models suitable for use with the design by inelastic analysis procedures.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of ASME Division 5 Code proposal on temperature limits for simplified design methods

This report establishes proposed upper temperature limits for the ASME BP&V Code Section III, Division 5, Nonmandatory Appendix HBB-T design by elastic analysis provisions for bounding ratcheting strain and creep-fatigue damage in Class A high temperature nuclear reactor components. Limitations on the use of these design options are required because the design by elastic analysis methods rely on bounding theories that assume a non-unified, decoupled model of creep-plasticity. However, at high temperatures creep and plastic deformation become coupled and bounding theorems relying a decoupled material response may fail. The report describes a method for selecting appropriate upper temperature limits, demonstrates directly through a comparison to full inelastic simulations that the existing Code provisions can be nonconservative at high temperatures, and develops the requisite Code language required to implement the temperature limits in Section III, Division 5.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Enhancements to the Munson-Dawson Model for Rock Salt

The Munson-Dawson (MD) constitutive model was originally developed in the 1980's to predict the thermomechanical behavior of rock salt. Since then, it has been used to simulate the evolution of the underground in nuclear waste repositories, mines, and storage caverns for gases and liquids. This report covers three enhancements to the MD model. (1) New transient and steady-state rate terms were added to capture salt's creep behavior at low equivalent stresses (below about 8 MPa). These new terms were calibrated against a series of triaxial compression creep experiments on salt from the Waste Isolation Pilot Plant. (2) The equivalent stress measure was changed from the Tresca stress to the Hosford stress. By varying a single exponent, the Hosford stress can reduce to the Tresca stress, the von Mises stress, or a range of behaviors in-between. This exponent was calibrated against true triaxial compression experiments on salt hollow cylinders. (3) The MD model's numerical implementation was overhauled, adding a line search algorithm to the implicit solution scheme. The new implementation was verified against analytical solutions, and benchmarked against a pre-existing implementation on a room closure simulation. The new implementation pre- dicted virtually identical room closure, yet sped up the simulation by 16x . (The source code of the new implementation is included in an appendix of this report.)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Stasis PCM Test Results

A phase change material product distributed by Stasis Group, designed to reduce the cooling energy requirements of multi-story commercial buildings, was tested in a side-by-side comparison at FLEXLAB® (LBNL, 2018), a calibrated test facility for low energy building technology solutions. The product was installed according to Stasis recommendations in the ceiling plenum of a 600 ft 2 cell representative of an office space, while an identical cell was operated in the same conditions, except for the night-time pre-cooling sequence and without the product, to gather baseline data. The cells were operated to replicate summer conditions of a candidate office building for retrofit. For the tests conducted at FLEXLAB, two Phase Change Material (PCM) compositions were tested, with the second product having an upgraded composition for thermal performance and upgraded packaging that was used to meet with fire safety requirements for a plenum application. Two rounds of tests were performed, which were designed to collect data for both core (designated as Round 1) and perimeter (Round 2) office space conditions. Following the analysis of the data collected during Round 1, the experimental design was modified to better represent the thermal conditions of a typical office space in relation to the PCM performance. A new product was also brought in for testing in Round 2, which had an improved operational temperature range and packaging properties. In Round 1, multiple tests were conducted to evaluate the performance of the product under different conditions of internal loads, temperature setpoints, pre-cooling strategies and temperature control strategies. In Round 2, the internal conditions were kept constant, while the test conditions only differ in the amount of PCM installed in the test cell plenum and the length of the nighttime pre-cooling sequence. The performance benefits of PCM are generally two-fold: the material may reduce peak cooling energy use during daytime hours (a peak demand energy use benefit) and may allow for energy savings with pre-cooling at night through night flush HVAC controls when night time outside air temperatures are lower, and fan energy use for cooling is more efficient than the use of daytime compressor-based cooling. The focus of this research project was mainly on quantifying the energy savings potential of the latter case although some effects on peak reduction were noted. Between the cell with PCM and nighttime precooling and the reference cell without PCM or precooling, a reduction in cooling load during occupied hours was noted between 7.6 kWh (or 22% of occupied hours cooling load) and 12.5 kWh (or 33% of occupied pg. 7 hours cooling load). Future work can further evaluate the peak cooling load reduction benefits of this product in more detail. This report highlights the results of Round 2, which reflect the performance of the modified PCM product when operated in suitable conditions. The results of Round 1, along with an analysis of the experimental data to identify the factors that prevented the product from performing as desired are presented in Appendix B.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Unsupervised Machine Learning for Evaluation of Aging in Explosive Pressed Pellets

This project is an evaluation of the changes in the dimensional geometry of pressed explosive powder pellets when stored for prolonged periods under unmonitored storage conditions. Through the application of Structural Health Monitoring (SHM) techniques, questions to be answered by this investigation are what, if any, effect has the long-term storage of the pellets had on their physical attributes and, if changes have occurred, are the resulting differences of significant magnitude to affect the performance of the pellets. This resulting report includes a summary of the relevant background information, explanation of the SHM approach used to analyze the available data, presentation and discussion of the results, concluding remarks, and an accompanying appendix containing the MATLAB program developed for the project.

36 MATERIALS SCIENCE↗

Polarization Experiments with Electromagnetic Probes (Final Technical Report)

The grant started in 1989 and finished on 31 July, 2018. The PI (Vina Punjabi) with many Norfolk State University (NSU) undergraduate students, and several research associates have been involved in many research activity during this period. NSU is primarily a minority institution. The PI has worked with one or two students every year, most of the students involved in her research went on to graduate schools to pursue degrees in physics, applied physics or engineering. One of the most important goal of the PI’s research activity has been involving NSU physics undergraduate students in forefront nuclear and particle physics research. (List of students and research associates is given in Appendix I). Over the years the PI, students and research associates participated in many research activity, however there are two main projects where the PI has been involved as one of the project leader. (1) Investigation of the structure of the deuteron at Saturne national lab in Saclay, France and at Laboratory of High Energy (LHE), part of the Joint Institute of Nuclear Research (JINR) lab in Dubna, Russia. (2) Measurement of the ratio of electric to magnetic form factors of the proton , GEp/GMp at Jefferson Lab, to study the internal structure of the proton.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Spectral Methods in Time-dependent Data Analysis

We aim to create a new model for time-dependent data analysis, named dynamical learning, that integrates data-driven manifold learning techniques with operator-theoretic methods from dynamical systems theory. This approach has the potential to deliver more efficient methods for analyzing time-dependent data, such as video streams, by naturally separating out the temporal and spatial features of the data. We aim to apply the newly developed methods to video surveillance data related to Sandia mission applications, and particularly focus on the problems of image segmentation and object tracking. This project ended early due to the departure of the PI from Sandia about 18 months into the project. Therefore, this document reports on partial progress towards the initial goals of the project. In addition, this document reports on part of the work conducted during the project; see the Appendix for a summary of all the work conducted during the 18 months.

97 MATHEMATICS AND COMPUTING↗

Analysis of 2016 Occurrence Reports Involving Electrical Energy

The 04100 Center Director requested an analysis of 2016 occurrence reports (ORs) involving electrical energy be performed to facilitate learning through use of performance assurance methodologies. Preliminarily, 11 reportable events were identified for review; however, this population was updated to 12 during the review. Appendix 1 includes the analysis protocol and a listing of the ORs reviewed. The Team completed its review at the end of October 2016. At that time, causal analysis and associated corrective action information was available for eight events. Elements of this analysis included determining the following: common weaknesses that contributed to electrical events; the quality of causal analysis products with the goal of providing sustainable long-term corrective actions; and how learning from issues, causes, and corrective actions from prior similar events is incorporated into causal analyses for today’s events. As used in this report, the term “trends” was used as a catalyst to determine categories of events for deeper analysis. The content of ORs is important. The information in an OR for a past event can be useful in addressing today’s issues because it provides information on systemic issues that were found and past actions addressing those issues. The effectiveness of those actions as viewed from today’s vantage point is useful input to the determination of corrective actions for current problems. Additionally, as a means of communication to DOE and NNSA, ORs provide a measure of Sandia’s maturity in understanding problems and their solutions.

42 ENGINEERING↗

Standard review plan for evaluating nuclear power reactor license termination plans

This standard review plan (SRP) guides the staff of the U.S. Nuclear Regulatory Commission (NRC) in conducting safety reviews of license termination plans (LTPs). The principal purpose of this SRP is to ensure the quality and uniformity of NRC staff reviews and to present a well-defined base from which to evaluate the requirements for terminating the license of a nuclear power plant. It is also the purpose of this SRP to make information about regulatory matters widely available, so that interested members of the public and the nuclear industry can gain a better understanding of the NRC staff's review process. Specific guidance for licensees is included in Regulatory Guide 1.179, "Standard Format and Content of License Termination Plans for Nuclear Power Reactors." Licensees may also use this SRP to assist in developing an LTP. The SRP presents the acceptance criteria for all areas of review for license termination, and identifies the matters to be reviewed, the basis for the review, and the conclusions that are sought. For example, NUREG-1757, "Consolidated Decommissioning Guidance" offers additional guidance on how to demonstrate compliance with the unrestricted release, restricted release, and alternative criteria for license termination, in accordance with Title 10 of the Code of Federal Regulations (10 CFR), Part 20, "Standards for Protection against Radiation," Subpart E, "Radiological Criteria for License Termination." To avoid duplication of information, this SRP references applicable sections of NUREG-1757 for additional guidance. In addition, the NRC has issued supplemental guidance that will subsequently be consolidated into NUREG-1757 to address partial site release before LTP approval, and compliance with 10 CFR Part 20, Subpart E. It should be noted that the memorandum of understanding (MOU) between the Environmental Protection Agency and NRC may contain consultation triggers for some radionuclides that may be lower than the NUREG-1757 Vol. 2 Revision 1, Appendix H screening values.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

(U) LNK3DNT Capability in SENSMG

The SENSMG multigroup neutron sensitivity code has been extended to read materials and geometry from redoin and lnk3dnt files written by the PARTISN multigroup discrete ordinates code or the MCNP6 Monte Carlo code. This report describes the user interface for this capability and the code verification that was done. Not all of the capability of SENSMG is available for redoin/lnk3dnt inputs. The only responses allowed are k eff or α eigenvalues. Fixed-source problems are not allowed, and there is no mechanism to input reaction rates or reaction-rate ratios. The next section of this report describes the user interface. Section III describes the verification of the capability. Section IV is a summary and conclusions. The input files used for verification are listed in the appendix.

97 MATHEMATICS AND COMPUTING↗

A JSON to CMake tool

As part of the conversion of the MCNP®testing system to CTest, a tool was needed to generate CMake variables from JSON formatted data structure. The system was first implemented using the JSON to CMake parser which with some slight modifications provided data useful for the MCNP CTest testing system. Upon further evaluation, we found it to be slow when setting up the 1600 tests during the CMake configuration step. Not only was it slow, it did not validate the JSON files during configuration allowing for unexpected behavior. Upon some web searching we came across a simple recursive python example that would provide the same capability needed by our testing system. This python example was effectively wrapped into a single python script that was used to convert the JSON data into CMake variables. This tool is attached as json_to_cmake.py and is listed in the appendix. In essence, the tool provides single variables for each value defined within the JSON file. The name for the variable is constructed by using the associated object names and array indicies needed to deference the variable itself. In the following sections, examples are provided to better describe how this is done.

97 MATHEMATICS AND COMPUTING↗

Underground Test Area Activity Preemptive Review Guidance Nevada National Security Site, Nevada

This report is a revision to the preemptive review (PER) guidance originally released as U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) document DOE/NV--1552 in 2016 (NNSA/NFO, 2016). PER committees review various products, including data, documents, software/codes, analyses, and models. PER committees provide technical recommendations to support regulatory decisions that are the responsibility of the DOE Environmental Management (EM) Nevada Program and NDEP. PERs are designed to be adaptable to the varying requirements of individual CAU studies. Their goals include the following: Maintaining high technical standards; ensuring work is technically adequate, competently performed, and documented consistent with other programmatic documents; and verifying that established quality requirements are satisfied. Helping focus CAU studies on UGTA Activity objectives identified in the FFACO by implementing Section 3 of Appendix VI, which includes the UGTA Strategy Flowchart (Figure 3-2) and Process Flow Diagram Dictionary for the UGTA CAUs (Table 3-1). Providing a mechanism for early identification of technical and/or strategy issues that could affect successfully implementing the UGTA strategy. Providing assurance to NDEP that work in progress and final reports are technically sound. Providing independent reviews that allow for a better understanding of the technical work, and result in products that are transparent and sufficient to allow the DOE EM Nevada Program to meet regulatory objectives.

54 ENVIRONMENTAL SCIENCES↗

Estimation of Dose from Potential Radionuclide Emissions from the Sample Preparation Laboratory at the Materials and Fuels Complex

The Sample Preparation Laboratory (SPL) at the Materials and Fuels Complex will perform sample preparation, examination, and mechanical-property testing of highly irradiated materials. The purpose of this report is to document calculation of the estimated dose at public receptor locations from potential radionuclide releases to the atmosphere from SPL. Atmospheric dispersion and dose calculations were performed with the computer model CAP88-PC Version 4 in accordance with the requirements of Code of Federal Regulations (CFR), Title 40, “Protection of the Environment,” Part 61, “National Emission Standards for Hazardous Air Pollutants (NESHAPs),” Subpart H, “National Emission Standards for Emissions of Radionuclides Other than Radon from Department of Energy Facilities” (40 CFR 61, Subpart H 2010). Emission potentials were calculated based on the methodology in 40 CFR Part 61, Appendix D and additional guidance/approval by EPA Region 10 [see letter from Donald Dossett (EPA Region 10) to Tim Safford (DOE-ID), Oct 19, 2017 (CCN 241475)] for solid materials that undergo heating. Estimates of total effective dose are based on low-level chronic exposure. The potential maximum dose to a member of the public was calculated to be 0.02 mrem/year based on an estimated 16 g of the 30 kg source term (0.053%) being exposed to very high temperatures associated with electrical-discharge machining (EDM) and the remaining material heated to 100°C. Calculations show the maximum dose could be as high as 0.05 mrem/year if the remaining material were heated to 1400°C (i.e., the melting point of stainless steel). The potential maximum dose to a public receptor from emissions at SPL is not expected to exceed 0.1 mrem/year (1% of the standard) so long as the material impacted by EDM does not exceed 56 g (3.5 times the expected mass of 16 g and less than 0.2% of the total source term), and the remaining material is not heated to temperatures greater than 1400°C. It should be noted that credit for HEPA filtration does not impact the dose results because the dose is dominated by radionuclides that have exceeded their boiling point; thus, no credit for HEPA filtration may be applied to the emission factor.

99 GENERAL AND MISCELLANEOUS↗

Coal-Fired Power Plants in the United States: Examination of the Costs of Retrofitting with CO 2 Capture Technology, Revision 3

This report describes the development of a database and geographic information systems (GIS) analysis of a defined population of coal-fired power plants in the U.S. to model the cost and assist in the assessment of the feasibility of retrofitting these plants with CO 2 capture technology. In addition, an assessment of the impacts on generation, CO 2 emission, and fuel consumption should all units be brought up to the average efficiency of the top decile of efficient units by nameplate was made. This report covers data sources, methodology employed, modeling and results. An appendix containing a catalog of aerial imagery used for this analysis is available as a separate document.

20 FOSSIL-FUELED POWER PLANTS↗

Lessons Learned NSLS-II Storage Magnet Production

This document was compiled in response to the suggestion made by the DOE SC Review of the NSLS-II Project on April 2012, and reiterated at the Review in July, 2013. The main contributors to this document are the SR magnet team A and other in-house participants in the Workshop B referred to below that took place on April 11 th and 12 th 2012 at BNL. The contributions also came from some external participants, including representatives of some of the suppliers who attended the workshop. Manufacturing of the magnets for the NSLS-II storage ring (~850 units of 15 types) took approximately 6 years from the beginning of the conceptual design to completion of manufacturing in October of 2012. The production in the early years did not go smoothly, and a DOE Review Committee expressed concerns in November of 2010 about the potential of significant delays in magnet deliveries. In response, the project undertook three major mitigation steps: 1) enhanced oversight by assignment of one technical representative for each of the seven suppliers, 2) appointment of a senior BNL scientist as the manager of the SR magnet production, and 3) streamlining the decision-making process. These steps led to a successful completion of magnet production and delivery with almost all magnets meeting their stringent specifications (see Appendix 2).

36 MATERIALS SCIENCE↗

Addendum to the Maximum Current of the Linac

The purpose of this technical note is to supplement the information provided in NSLS-II Technical Note 105: Maximum Current of the NSLS-II Linac. This is included in the Linac Commissioning SAD Addendum as Appendix B. Technical Note 105 made some assumptions which have been subjected to further analysis. This technical note will reexamine some of these assumptions. This technical note includes additional analysis of: 1. Updated PARMELA model of the linac 2. Updated beam loading model 3. Gun faults which lead to full discharge of the gun and high voltage deck 4. Consideration of the case where the gun can emit more charge than has been measured by manufacturer, but within cathode specifications. In all cases the linac ASE is not violated either of operation because not enough current is generated or recovery from the fault will take enough time that violating the ASE is not possible.

36 MATERIALS SCIENCE↗

Industrial Activities Stormwater Pollution Prevention Plan (Rev. 1)

The Sandia National Laboratories, California (SNL/CA) site comprises approximately 410 acres and is located in the eastern portion of Livermore, Alameda County, California. The property is owned by the United States Department of Energy and is being operated by Sandia Corporation. The facility location is shown on the Site Map(s) in Appendix A. This Stormwater Pollution Prevention Plan (SWPPP) is designed to comply with California’s General Permit for Stormwater Discharges Associated with Industrial Activities (General Permit) Order No. 2014-0057-DWQ (NPDES No. CAS000001) issued by the State Water Resources Control Board (State Water Board) (Ref. 6.1). This SWPPP has been prepared following the SWPPP Template provided on the California Stormwater Quality Association Stormwater Best Management Practice Handbook Portal: Industrial and Commercial (CASQA 2014).

54 ENVIRONMENTAL SCIENCES↗

Stormwater Pollution Prevention Plan, TA-03-38 Carpenter's Shop, Revision 4: LANS Archived 2019

This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector A–Timber Products, Subsector A4 (Wood Products Facilities not elsewhere classified) as a guide. The applicable stormwater discharge permit is EPA General Permit Registration # NMR053915 (Los Alamos National Security (LANS) (U.S. EPA, June 2015). This SWPPP applies to discharges of stormwater from the operational areas of the TA-03-38 Carpenter’s Shop at Los Alamos National Laboratory. Los Alamos National Laboratory (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-03-38 Carpenter’s Shop and associated areas. The current permit expires at midnight on June 4, 2020. As the LANS contract ended for LANL MSGP facilities on October 31, 2018, a Notice of Termination (NOT) for permit coverage was filed and is effective as of 11/02/18. A copy of the NOT acknowledgment is located in Appendix C of this SWPPP. This is the archived and final revision of the SWPPP for LANS.

54 ENVIRONMENTAL SCIENCES↗