Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ZINC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Impact of hydrogen and oxygen defects on the lattice parameter of chemical vapor deposited zinc sulfide

The lattice parameter of cubic chemical vapor deposited (CVD) ZnS with measured oxygen concentrations < 0.6 at.% and hydrogen impurities of < 0.015 at.% have been measured and found to vary between -0.10% and +0.09% relative to the reference lattice parameter (5.4093 Å) of oxygen-free cubic ZnS as reported in the literature. Defects other than substitutional O must be invoked to explain these observed volume changes. The structure and thermodynamic stability of a wide range of native and impurity induced defects in ZnS have been determined by Ab initio calculations. Lattice contraction is caused by S-vacancies, substitutional O on S sites, Zn vacancies, H in S vacancies, peroxy defects, and dissociated water in S-vacancies. The lattice is expanded by interstitial H, H in Zn vacancies, dihydroxy defects, interstitial oxygen, Zn and [ZnHn] complexes (n=1,…,4), interstitial Zn, and S2 dumbbells. Oxygen, though present, likely forms substitutional defects for sulfur resulting in lattice contraction rather than as interstitial oxygen resulting in lattice expansion. It is concluded based on measurement and calculations that excess zinc atoms either at anti-sites (i.e. Zn atoms on S-sites) or possibly as interstitial Zn are responsible for the relative increase of the lattice parameter of commercially produced CVD ZnS.

ab initio↗

Experimental and first-principles study of ferromagnetism in Mn-doped zinc stannate nanowires

Room temperature ferromagnetism was observed in Mn-doped zinc stannate (ZTO:Mn) nanowires, which were prepared by chemical vapor transport. Structural and magnetic properties and Mn chemical states of ZTO:Mn nanowires were investigated by X-ray diffraction, superconducting quantum interference device (SQUID) magnetometry and X-ray photoelectron spectroscopy. Manganese predominantly existed as Mn{sup 2+} and substituted for Zn (Mn{sub Zn}) in ZTO:Mn. This conclusion was supported by first-principles calculations. Mn{sub Zn} in ZTO:Mn had a lower formation energy than that of Mn substituted for Sn (Mn{sub Sn}). The nearest neighbor Mn{sub Zn} in ZTO stabilized ferromagnetic coupling. This observation supported the experimental results.

36 MATERIALS SCIENCE↗

Investigating the effect of characteristic x-rays in cadmium zinc telluride detectors under breast computerized tomography operating conditions

A number of research groups have been investigating the use of dedicated breast computerized tomography (CT). Preliminary results have been encouraging, suggesting an improved visualization of masses on breast CT as compared to conventional mammography. Nonetheless, there are many challenges to overcome before breast CT can become a routine clinical reality. One potential improvement over current breast CT prototypes would be the use of photon counting detectors with cadmium zinc telluride (CZT) (or CdTe) semiconductor material. These detectors can operate at room temperature and provide high detection efficiency and the capability of multi-energy imaging; however, one factor in particular that limits image quality is the emission of characteristic x-rays. In this study, the degradative effects of characteristic x-rays are examined when using a CZT detector under breast CT operating conditions. Monte Carlo simulation software was used to evaluate the effect of characteristic x-rays and the detector element size on spatial and spectral resolution for a CZT detector used under breast CT operating conditions. In particular, lower kVp spectra and thinner CZT thicknesses were studied than that typically used with CZT based conventional CT detectors. In addition, the effect of characteristic x-rays on the accuracy of material decomposition in spectral CT imaging was explored. It was observed that when imaging with 50-60 kVp spectra, the x-ray transmission through CZT was very low for all detector thicknesses studied (0.5–3.0 mm), thus retaining dose efficiency. As expected, characteristic x-ray escape from the detector element of x-ray interaction increased with decreasing detector element size, approaching a 50% escape fraction for a 100 μm size detector element. The detector point spread function was observed to have only minor degradation with detector element size greater than 200 μm and lower kV settings. Characteristic x-rays produced increasing distortion in the spectral response with decreasing detector element size. If not corrected for, this caused a large bias in estimating tissue density parameters for material decomposition. It was also observed that degradation of the spectral response due to characteristic x-rays caused worsening precision in the estimation of tissue density parameters. It was observed that characteristic x-rays do cause some degradation in the spatial and spectral resolution of thin CZT detectors operating under breast CT conditions. These degradations should be manageable with careful selection of the detector element size. Even with the observed spectral distortion from characteristic x-rays, it is still possible to correctly estimate tissue parameters for material decomposition using spectral CT if accurate modeling is used.

36 MATERIALS SCIENCE↗

Influence of growth temperature on electrical, optical, and plasmonic properties of aluminum:zinc oxide films grown by radio frequency magnetron sputtering

We have investigated the responsible mechanism for the observation of metallic conductivity at room temperature and metal-semiconductor transition (MST) at lower temperatures for aluminum-doped zinc oxide (AZO) films. AZO films were grown on glass substrates by radio-frequency magnetron sputtering with varying substrate temperatures (T{sub s}). The films were found to be crystalline with the electrical resistivity close to 1.1 × 10{sup −3} Ω cm and transmittance more than 85% in the visible region. The saturated optical band gap of 3.76 eV was observed for the sample grown at T{sub s} of 400 °C, however, a slight decrease in the bandgap was noticed above 400 °C, which can be explained by Burstein–Moss effect. Temperature dependent resistivity measurements of these highly conducting and transparent films showed a MST at ∼110 K. The observed metal-like and metal-semiconductor transitions are explained by taking into account the Mott phase transition and localization effects due to defects. All AZO films demonstrate crossover in permittivity from positive to negative and low loss in the near-infrared region, illustrating its applications for plasmonic metamaterials, including waveguides for near infrared telecommunication region. Based on the results presented in this study, the low electrical resistivity and high optical transmittance of AZO films suggested a possibility for the application in the flexible electronic devices, such as transparent conducting oxide film on LEDs, solar cells, and touch panels.

36 MATERIALS SCIENCE↗

Surface reactivity and oxygen migration in amorphous indium-gallium-zinc oxide films annealed in humid atmosphere

An isotope tracer study, i.e., {sup 18}O/{sup 16}O exchange using {sup 18}O{sub 2} and H{sub 2}{sup 18}O, was performed to determine how post-deposition annealing (PDA) affected surface reactivity and oxygen diffusivity of amorphous indium–gallium–zinc oxide (a-IGZO) films. The oxygen tracer diffusivity was very high in the bulk even at low temperatures, e.g., 200 °C, regardless of PDA and exchange conditions. In contrast, the isotope exchange rate, dominated by surface reactivity, was much lower for {sup 18}O{sub 2} than for H{sub 2}{sup 18}O. PDA in a humid atmosphere at 400 °C further suppressed the reactivity of O{sub 2} at the a-IGZO film surface, which is attributable to –OH-terminated surface formation.

36 MATERIALS SCIENCE↗

Recovery from ultraviolet-induced threshold voltage shift in indium gallium zinc oxide thin film transistors by positive gate bias

The effect of short-duration ultraviolet (UV) exposure on the threshold voltage (V{sub th}) of amorphous indium gallium zinc oxide thin film transistors (TFTs) and its recovery characteristics were investigated. The V{sub th} exhibited a significant negative shift after UV exposure. The V{sub th} instability caused by UV illumination is attributed to the positive charge trapping in the dielectric layer and/or at the channel/dielectric interface. The illuminated devices showed a slow recovery in threshold voltage without external bias. However, an instant recovery can be achieved by the application of positive gate pulses, which is due to the elimination of the positive trapped charges as a result of the presence of a large amount of field-induced electrons in the interface region.

36 MATERIALS SCIENCE↗

Reduction of defect formation in amorphous indium-gallium-zinc-oxide thin film transistors by N{sub 2}O plasma treatment

An abnormal sub-threshold leakage current is observed at high temperature in amorphous indium-gallium-zinc-oxide thin film transistors (a-IGZO TFTs). This phenomenon occurs due to a reduced number of defects in the device's a-IGZO active layer after the device has undergone N{sub 2}O plasma treatment. Experimental verification shows that the N{sub 2}O plasma treatment enhances the thin film bonding strength, thereby suppressing the formation of temperature-dependent holes, which are generated above 400 K by oxygen atoms leaving their original sites. The N{sub 2}O plasma treatment devices have better stability performance than as-fabricated devices. The results suggest that the density of defects for a-IGZO TFTs with N{sub 2}O plasma treatment is much lower than that in as-fabricated devices. The N{sub 2}O plasma treatment repairs the defects and suppresses temperature-dependent sub-threshold leakage current.

36 MATERIALS SCIENCE↗

Zinc oxide integrated area efficient high output low power wavy channel thin film transistor

We report an atomic layer deposition based zinc oxide channel material integrated thin film transistor using wavy channel architecture allowing expansion of the transistor width in the vertical direction using the fin type features. The experimental devices show area efficiency, higher normalized output current, and relatively lower power consumption compared to the planar architecture. This performance gain is attributed to the increased device width and an enhanced applied electric field due to the architecture when compared to a back gated planar device with the same process conditions.

36 MATERIALS SCIENCE↗

Ab initio study of phase transition of boron nitride between zinc-blende and rhombohedral structures

Boron nitride has polymorphs such as zinc-blende (c-BN), wurtzite (w-BN), rhombohedral (r-BN), and graphite-like (h-BN) forms. We simulate the direct conversion of r-BN to c-BN through electronic excitation. In our calculation, the conversion is made possible by increasing the hole concentration to over 0.06/atom. This conversion should be experimentally possible by hole-doping via an electric double layer transistor (EDLT) or capacitor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Zinc oxide thin film acoustic sensor

This paper reports the implementation of (750 nm) thickness of Zinc Oxide (ZnO) thin film for the piezoelectric pressure sensors. The film was prepared and deposited employing the spray pyrolysis technique. XRD results show that the growth preferred orientation is the (002) plane. A polycrystalline thin film (close to mono crystallite like) was obtained. Depending on the Scanning Electron Microscopy photogram, the film homogeneity and thickness were shown. The resonance frequency measured (about 19 kHz) and the damping coefficient was calculated and its value was found to be about (2.5538), the thin film be haves as homogeneous for under and over damped. The thin film pressure sensing was approximately exponentially related with frequency, the thin film was observed to has a good response for mechanical stresses also it is a good material for the piezoelectric properties.

36 MATERIALS SCIENCE↗

Growth mechanism of atomic layer deposition of zinc oxide: A density functional theory approach

Atomic layer deposition of zinc oxide (ZnO) using diethylzinc (DEZ) and water is studied using density functional theory. The reaction pathways between the precursors and ZnO surface sites are discussed. Both reactions proceed by the formation of intermediate complexes on the surface. The Gibbs free energy of the formation of these complexes is positive at temperatures above ∼120 °C and ∼200 °C for DEZ and water half-reactions, respectively. Spectroscopic ellipsometry results show that the growth per cycle changes at approximately the same temperatures.

36 MATERIALS SCIENCE↗

Low power zinc-oxide based charge trapping memory with embedded silicon nanoparticles via poole-frenkel hole emission

A low power zinc-oxide (ZnO) charge trapping memory with embedded silicon (Si) nanoparticles is demonstrated. The charge trapping layer is formed by spin coating 2 nm silicon nanoparticles between Atomic Layer Deposited ZnO steps. The threshold voltage shift (ΔV{sub t}) vs. programming voltage is studied with and without the silicon nanoparticles. Applying −1 V for 5 s at the gate of the memory with nanoparticles results in a ΔV{sub t} of 3.4 V, and the memory window can be up to 8 V with an excellent retention characteristic (>10 yr). Without nanoparticles, at −1 V programming voltage, the ΔV{sub t} is negligible. In order to get ΔV{sub t} of 3.4 V without nanoparticles, programming voltage in excess of 10 V is required. The negative voltage on the gate programs the memory indicating that holes are being trapped in the charge trapping layer. In addition, at 1 V the electric field across the 3.6 nm tunnel oxide is calculated to be 0.36 MV/cm, which is too small for significant tunneling. Moreover, the ΔV{sub t} vs. electric field across the tunnel oxide shows square root dependence at low fields (E < 1 MV/cm) and a square dependence at higher fields (E > 2.7 MV/cm). This indicates that Poole-Frenkel Effect is the main mechanism for holes emission at low fields and Phonon Assisted Tunneling at higher fields.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Integration and structural analysis of strain relaxed bi-epitaxial zinc oxide(0001) thin film with silicon(100) using titanium nitride buffer layer

Epitaxial growth of c-plane ZnO(0001) has been demonstrated on the Si(001) by using TiN as an intermediate buffer layer. Because of different out of plane symmetry of the substrate (Si/TiN) and the film (ZnO), two orientations of ZnO domains were obtained and the ZnO film growth is of bi-epitaxial nature. The ZnO thin film was observed to be nearly strain relaxed from X-ray and Raman measurements. The interface between the ZnO and TiN was investigated by transmission electron microscopy, and atomic arrangement has been modeled to understand the crystallographic orientation and structure of the domain/grain boundaries. Reaction at ZnO/TiN interface at higher growth temperature causing zinc titanate formation was observed. The grain boundary structure between the observed domains investigated by scanning transmission electron microscopy, revealed the ZnO(0001) planes to be contiguous across the grain boundary which is significant from the perspective of conduction electron scattering. In this configuration, the TiN (being electrically conductive) can be effectively used as an electrode for novel vertically integrated device applications (like light emitting diodes) directly on Si(100) substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Coplanar amorphous-indium-gallium-zinc-oxide thin film transistor with He plasma treated heavily doped layer

We report thermally stable coplanar amorphous-indium-gallium-zinc-oxide (a-IGZO) thin-film transistors (TFTs) with heavily doped n{sup +} a-IGZO source/drain regions. Doping is through He plasma treatment in which the resistivity of the a-IGZO decreases from 2.98 Ω cm to 2.79 × 10{sup −3} Ω cm after treatment, and then it increases to 7.92 × 10{sup −2} Ω cm after annealing at 300 °C. From the analysis of X-ray photoelectron spectroscopy, the concentration of oxygen vacancies in He plasma treated n{sup +}a-IGZO does not change much after thermal annealing at 300 °C, indicating thermally stable n{sup +} a-IGZO, even for TFTs with channel length L = 4 μm. Field-effect mobility of the coplanar a-IGZO TFTs with He plasma treatment changes from 10.7 to 9.2 cm{sup 2}/V s after annealing at 300 °C, but the performance of the a-IGZO TFT with Ar or H{sub 2} plasma treatment degrades significantly after 300 °C annealing.

36 MATERIALS SCIENCE↗

Realization of write-once-read-many-times memory device with O{sub 2} plasma-treated indium gallium zinc oxide thin film

A write-once-read-many-times (WORM) memory devices based on O{sub 2} plasma-treated indium gallium zinc oxide (IGZO) thin films has been demonstrated. The device has a simple Al/IGZO/Al structure. The device has a normally OFF state with a very high resistance (e.g., the resistance at 2 V is ∼10{sup 9} Ω for a device with the radius of 50 μm) as a result of the O{sub 2} plasma treatment on the IGZO thin films. The device could be switched to an ON state with a low resistance (e.g., the resistance at 2 V is ∼10{sup 3} Ω for the radius of 50 μm) by applying a voltage pulse (e.g., 10 V/1 μs). The WORM device has good data-retention and reading-endurance capabilities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Constrained, aqueous growth of three-dimensional single crystalline zinc oxide structures

We study low temperature (90 °C) aqueous growth of single crystal zinc oxide structures through patterned PMMA molds of different sizes, shapes, and orientations. We demonstrate the ability to create 3D shapes with smooth vertical sidewalls. Although the unconstrained growth is influenced by the hexagonal geometry of the underlying crystal structure, the ZnO is shown to conform exactly to any shape patterned. Using electron backscatter diffraction and scanning electron microscopy we show that the mold orientation, in conjunction with control of the growth rates of the c and m planes of the ZnO, is crucial in determining the final structure shape.

36 MATERIALS SCIENCE↗

The electrical conduction properties of poly-crystalline indium-zinc-oxide film

We have developed a high-mobility and high-uniform oxide semiconductor using poly-crystalline semiconductor material composed of indium and zinc (p-IZO). A typical conduction mechanism of p-IZO film was demonstrated by the grain boundary scattering model as in polycrystalline silicon. The grain boundary potential of the 2-h-annealed IZO film was calculated to be 100 meV, which was comparable to that of the polycrystalline silicon. However, the p-IZO thin film transistor (TFT) measurement shows rather uniform characteristics. It denotes that the mobility deterioration around the grain boundaries is lower than the case for low-temperature polycrystalline silicon. This assertion was made based on the difference of the mobility between the polycrystalline and amorphous IZO film being much smaller than is the case for silicon transistors. Therefore, we conclude that the p-IZO is a promising material for a TFT channel, which realizes high drift mobility and uniformity simultaneously.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The E3 center in zinc oxide: Evidence for involvement of hydrogen

Proton implantation is shown to increase the concentration of the so called and commonly observed E3 defect level in zinc oxide (ZnO). Box and single profiles of protons with doses ranging from 6×10{sup 10} cm{sup −2} to 4.3×10{sup 12} cm{sup −2} were implanted into hydrothermally grown ZnO samples with original concentrations of E3 below 5×10{sup 14} cm{sup −3}. Capacitance-Voltage profiling and junction spectroscopy measurements showed that the charge carrier concentration and absolute concentration of E3 centers increase by more than one order of magnitude compared to the as-grown samples as well as control samples implanted with He ions. The results provide strong evidence for the involvement of H in the formation of the E3 center, and a complex involving interstitial H and an oxygen sub-lattice primary defect are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗