Results for “Support Activities” — Page 50

NASA NTRS2013

Large Scale Flame Spread Environmental Characterization Testing

Under the Advanced Exploration Systems (AES) Spacecraft Fire Safety Demonstration Project (SFSDP), as a risk mitigation activity in support of the development of a large-scale fire demonstration experiment in microgravity, flame-spread tests were conducted in normal gravity on thin, cellulose-based fuels in a sealed chamber. The primary objective of the tests was to measure pressure rise in a chamber as sample material, burning direction (upward/downward), total heat release, heat release rate, and heat loss mechanisms were varied between tests. A Design of Experiments (DOE) method was imposed to produce an array of tests from a fixed set of constraints and a coupled response model was developed. Supplementary tests were run without experimental design to additionally vary select parameters such as initial chamber pressure. The starting chamber pressure for each test was set below atmospheric to prevent chamber overpressure. Bottom ignition, or upward propagating burns, produced rapid acceleratory turbulent flame spread. Pressure rise in the chamber increases as the amount of fuel burned increases mainly because of the larger amount of heat generation and, to a much smaller extent, due to the increase in gaseous number of moles. Top ignition, or downward propagating burns, produced a steady flame spread with a very small flat flame across the burning edge. Steady-state pressure is achieved during downward flame spread as the pressure rises and plateaus. This indicates that the heat generation by the flame matches the heat loss to surroundings during the longer, slower downward burns. One heat loss mechanism included mounting a heat exchanger directly above the burning sample in the path of the plume to act as a heat sink and more efficiently dissipate the heat due to the combustion event. This proved an effective means for chamber overpressure mitigation for those tests producing the most total heat release and thusly was determined to be a feasible mitigation strategy to incorporate into the microgravity experiment.

Clayman, Lauren K.↗

NASA NTRS2014

Advanced Sine Wave Modulation of Continuous Wave Laser System for Atmospheric CO2 Differential Absorption Measurements

NASA Langley Research Center in collaboration with ITT Exelis have been experimenting with Continuous Wave (CW) laser absorption spectrometer (LAS) as a means of performing atmospheric CO2 column measurements from space to support the Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) mission.Because range resolving Intensity Modulated (IM) CW lidar techniques presented here rely on matched filter correlations, autocorrelation properties without side lobes or other artifacts are highly desirable since the autocorrelation function is critical for the measurements of lidar return powers, laser path lengths, and CO2 column amounts. In this paper modulation techniques are investigated that improve autocorrelation properties. The modulation techniques investigated in this paper include sine waves modulated by maximum length (ML) sequences in various hardware configurations. A CW lidar system using sine waves modulated by ML pseudo random noise codes is described, which uses a time shifting approach to separate channels and make multiple, simultaneous online/offline differential absorption measurements. Unlike the pure ML sequence, this technique is useful in hardware that is band pass filtered as the IM sine wave carrier shifts the main power band. Both amplitude and Phase Shift Keying (PSK) modulated IM carriers are investigated that exibit perfect autocorrelation properties down to one cycle per code bit. In addition, a method is presented to bandwidth limit the ML sequence based on a Gaussian filter implemented in terms of Jacobi theta functions that does not seriously degrade the resolution or introduce side lobes as a means of reducing aliasing and IM carrier bandwidth.

Campbell, Joel F.↗

NASA NTRS2014

The Nuclear Thermal Propulsion Stage (NTPS): A Key Space Asset for Human Exploration and Commercial Missions to the Moon

The nuclear thermal rocket (NTR) has frequently been discussed as a key space asset that can bridge the gap between a sustained human presence on the Moon and the eventual human exploration of Mars. Recently, a human mission to a near Earth asteroid (NEA) has also been included as a "deep space precursor" to an orbital mission of Mars before a landing is attempted. In his "post-Apollo" Integrated Space Program Plan (1970 to 1990), Wernher von Braun, proposed a reusable Nuclear Thermal Propulsion Stage (NTPS) to deliver cargo and crew to the Moon to establish a lunar base initially before sending human missions to Mars. The NTR was selected because it was a proven technology capable of generating both high thrust and high specific impulse (Isp approx. 900 s)-twice that of today's best chemical rockets. During the Rover and NERVA programs, 20 rocket reactors were designed, built and successfully ground tested. These tests demonstrated the (1) thrust levels; (2) high fuel temperatures; (3) sustained operation; (4) accumulated lifetime; and (5) restart capability needed for an affordable in-space transportation system. In NASA's Mars Design Reference Architecture (DRA) 5.0 study, the "Copernicus" crewed NTR Mars transfer vehicle used three 25 klbf "Pewee" engines-the smallest and highest performing engine tested in the Rover program. Smaller lunar transfer vehicles-consisting of a NTPS with three approx. 16.7 klbf "SNRE-class" engines, an in-line propellant tank, plus the payload-can be delivered to LEO using a 70 t to LEO upgraded SLS, and can support reusable cargo delivery and crewed lunar landing missions. The NTPS can play an important role in returning humans to the Moon to stay by providing an affordable in-space transportation system that can allow initial lunar outposts to evolve into settlements capable of supporting commercial activities. Over the next decade collaborative efforts between NASA and private industry could open up new exploration and commercial opportunities for both organizations. With efficient NTP, commercial habitation and crew delivery systems, a "mobile cislunar research station" can transport crews to small NEAs delivered to the E-ML2 point. Also possible are week-long "lunar tourism" missions that can carry passengers into lunar orbit for sightseeing (and plenty of picture taking), then return them to Earth orbit where they would re-enter and land using a small reusable lifting body based on NASA's HL-20 design. Mission descriptions, key vehicle features and operational characteristics are described and presented.

Borowski, Stanley K.↗

NASA NTRS2015

JSC Advanced Curation: Research and Development for Current Collections and Future Sample Return Mission Demands

Curation of NASA's astromaterials sample collections is a demanding and evolving activity that supports valuable science from NASA missions for generations, long after the samples are returned to Earth. For example, NASA continues to loan hundreds of Apollo program samples to investigators every year and those samples are often analyzed using instruments that did not exist at the time of the Apollo missions themselves. The samples are curated in a manner that minimizes overall contamination, enabling clean, new high-sensitivity measurements and new science results over 40 years after their return to Earth. As our exploration of the Solar System progresses, upcoming and future NASA sample return missions will return new samples with stringent contamination control, sample environmental control, and Planetary Protection requirements. Therefore, an essential element of a healthy astromaterials curation program is a research and development (R&D) effort that characterizes and employs new technologies to maintain current collections and enable new missions - an Advanced Curation effort. JSC's Astromaterials Acquisition & Curation Office is continually performing Advanced Curation research, identifying and defining knowledge gaps about research, development, and validation/verification topics that are critical to support current and future NASA astromaterials sample collections. The following are highlighted knowledge gaps and research opportunities.

Fries, M. D.↗

NASA NTRS2012

Cassini Thruster Calibration Algorithm Using Reaction Wheel Biasing Data

Thrust force estimates for the reaction control thrusters on-board Cassini spacecraft are presented in this paper. Cassini consists of two thruster branches (A and B) each with eight thrusters. The four Z-thrusters control the X and Y-axes, while the four Y-thrusters control the Z-axis. It is important to track the thrust force estimates in order to detect any thruster degradation and for supporting various activities in spacecraft operations (Titan flyby, spacecraft maneuvers). The Euler equation, which describes the rotational motion of the spacecraft during a reaction wheel bias event, is used to develop the algorithm. The thrust estimates are obtained from the pseudo inverse solution using flight telemetry during the bias. Results show that the A-branch Z3A and Z4A thrusters exhibited degraded thrust in November 2008. Due to the degraded thrust performance of Z3A and Z4A, A-branch usage was discontinued and prime branch was swapped to B-branch in March 2009. The thrust estimates from the B-branch do not show any degradation to date. The algorithm is used to trend the B-branch thrust force estimates as the mission continues.

attitude control↗

NASA NTRS2014

Rodent Research on the International Space Station - A Look Forward

Rodent Research on the International Space Station (ISS) is one of the highest priority science activities being supported by NASA and is planned for up to two flights per year. The first Rodent Research flight, Rodent Research-1 (RR-1) validates the hardware and basic science operations (dissections and tissue preservation). Subsequent flights will add new capabilities to support rodent research on the ISS. RR-1 will validate the following capabilities: animal husbandry for up to 30 days, video downlink to support animal health checks and scientific analysis, on-orbit dissections, sample preservation in RNA. Later and formalin, sample transfer from formalin to ethanol (hindlimbs), rapid cool-down and subsequent freezing at -80 of tissues and carcasses, sample return and recovery. RR-2, scheduled for SpX-6 (Winter 20142015) will add the following capabilities: animal husbandry for up to 60 days, RFID chip reader for individual animal identification, water refill and food replenishment, anesthesia and recovery, bone densitometry, blood collection (via cardiac puncture), blood separation via centrifugation, soft tissue fixation in formalin with transfer to ethanol, and delivery of injectable drugs that require frozen storage prior to use. Additional capabilities are also planned for future flights and these include but are not limited to male mice, live animal return, and the development of experiment unique equipment to support science requirements for principal investigators that are selected for flight. In addition to the hardware capabilities to support rodent research the Crew Office has implemented a training program in generic rodent skills for all USOS crew members during their pre-assignment training rotation. This class includes training in general animal handling, euthanasia, injections, and dissections. The dissection portion of this training focuses on the dissection of the spleen, liver, kidney with adrenals, brain, eyes, and hindlimbs. By achieving and maintaining proficiency in these basic skills as part of the nominal astronaut training curriculum this allows the rodent research program to focus the mission specific crew training on scientific requirements of research and operations flow.

Experimental capabilities↗

NASA NTRS2016

Position Paper: Designing Complex Systems to Support Interdisciplinary Cognitive Work

The paper argues that the field we can call cognitive science of interdisciplinary collaboration is an important area of study for improving design of Large-Scale Complex Systems (LaCES) and supporting cognitive work. The paper mostly raised questions that have been documented in earlier qualitative analysis studies, and provided possible avenues of exploration for addressing them. There are likely further contributions from additional disciplines beyond those mentioned in this paper that should be considered and integrated into such a cognitive science framework. Knowledge and awareness of various perspectives will help to inform the types of interventions available for improving LaCES design and functionality. For example, a cognitive interpretation of interdisciplinary collaborations in LaCES elucidated the need for a "translator" or "mediator" in helping subject matter experts to transcend language boundaries, mitigate single discipline bias, support integrative activities, and correct misaligned objectives. Additional research in this direction is likely to uncover similar gaps and opportunities for improvements in practice.

Greene, Melissa T.↗

NASA NTRS2016

Digital Image Correlation Techniques Applied to Large Scale Rocket Engine Testing

Rocket engine hot-fire ground testing is necessary to understand component performance, reliability and engine system interactions during development. The J-2X upper stage engine completed a series of developmental hot-fire tests that derived performance of the engine and components, validated analytical models and provided the necessary data to identify where design changes, process improvements and technology development were needed. The J-2X development engines were heavily instrumented to provide the data necessary to support these activities which enabled the team to investigate any anomalies experienced during the test program. This paper describes the development of an optical digital image correlation technique to augment the data provided by traditional strain gauges which are prone to debonding at elevated temperatures and limited to localized measurements. The feasibility of this optical measurement system was demonstrated during full scale hot-fire testing of J-2X, during which a digital image correlation system, incorporating a pair of high speed cameras to measure three-dimensional, real-time displacements and strains was installed and operated under the extreme environments present on the test stand. The camera and facility setup, pre-test calibrations, data collection, hot-fire test data collection and post-test analysis and results are presented in this paper.

Gradl, Paul R.↗

NASA NTRS2017

EVA Systems Technology Gaps and Priorities 2017

Performance of Extra-Vehicular Activities (EVA) has been and will continue to be a critical capability for human space flight. Human exploration missions beyond LEO will require EVA capability for either contingency or nominal activities to support mission objectives and reduce mission risk. EVA systems encompass a wide array of products across pressure suits, life support systems, EVA tools and unique spacecraft interface hardware (i.e. EVA Translation Paths and EVA Worksites). In a fiscally limited environment with evolving transportation and habitation options, it is paramount that the EVA community's strategic planning and architecture integration products be reviewed and vetted for traceability between the mission needs far into the future to the known technology and knowledge gaps to the current investments across EVA systems. To ascertain EVA technology and knowledge gaps many things need to be brought together, assessed and analyzed. This includes an understanding of the destination environments, various mission concept of operations, current state of the art of EVA systems, EVA operational lessons learned, and reference advanced capabilities. A combined assessment of these inputs should result in well-defined list of gaps. This list can then be prioritized depending on the mission need dates and time scale of the technology or knowledge gap closure plan. This paper will summarize the current state of EVA related technology and knowledge gaps derived from NASA's Exploration EVA Reference Architecture and Operations Concept products. By linking these products and articulating NASA's approach to strategic development for EVA across all credible destinations an EVA could be done in, the identification of these gaps is then used to illustrate the tactical and strategic planning for the EVA technology development portfolio. Finally, this paper illustrates the various "touch points" with other human exploration risk identification areas including human health and performance.

Johnson, Brian J.↗

NASA NTRS2018

Concept Vehicles for VTOL Air Taxi Operations

Concept vehicles are presented for air taxi operations, also known as urban air mobility or on-demand mobility applications. Considering the design-space dimensions of payload (passengers and pilot), range, aircraft type, and propulsion system, three aircraft are designed: a single passenger (250-lb payload), 50-nm range quadrotor with electric propulsion; a six-passenger (1200-lb payload), 4x50 = 200-nm range side-by-side helicopter with hybrid propulsion; and a fifteen-passenger (3000-lb payload), 8x50 = 400-nm range tiltwing with turbo-electric propulsion. These concept vehicles are intended to focus and guide NASA research activities in support of aircraft development for emerging aviation markets, in particular VTOL air taxi operations. Research areas are discussed, illustrated by results from the design of the concept vehicles.

Concept↗

NASA NTRS2018

Electrical Characteristics of the Mars Electrostatic Precipitator

NASA's next generation Mars missions will include chemical processing plants to convert the Martian atmosphere into consumable products needed to support astronaut activities. The thin, mostly carbon dioxide atmosphere of Mars is estimated to have 5-10 particles/cu. cm which have a radius of 1.6-2.27 microns on average. These dust particles could potentially foul the chemical process or reduce the purity of the products. Electrostatic precipitation is one possible solution to remove dust particles from the ingested Mars atmosphere. The Electrostatics and Surface Physics Laboratory at NASA's Kennedy Space Center has developed an electrostatic precipitator testbed to understand the intricacies of corona discharges in dusty flows simulating Mars atmospheric conditions. Current-voltage trends have been established for a number of precipitator flow conditions. Corona onset voltage and streamer onset voltage trends versus pressure are also established.

Johansen, Michael R.↗

NASA NTRS2018

Electrical Characteristics of the Mars Electrostatic Precipitator

NASA's next generation Mars missions will include chemical processing plants to convert the Martian atmosphere into consumable products needed to support astronaut activities. The thin, mostly carbon dioxide atmosphere of Mars is estimated to have 5-10 particles/cu. cm which have a radius of 1.6-2.27 microns on average. These dust particles could potentially foul the chemical process or reduce the purity of the products. Electrostatic precipitation is one possible solution to remove dust particles from the ingested Mars atmosphere. The Electro-statics and Surface Physics Laboratory at NASA's Kennedy Space Center has developed an electrostatic precipitator testbed to understand the intricacies of corona discharges in dusty flows simulating Mars atmospheric conditions. Current-voltage trends have been estab-lished for a number of precipitator flow conditions. Corona onset voltage and streamer onset voltage trends versus pressure are also established.

Johansen, Michael R.↗

NASA NTRS2018

NASA ACC High Energy Dynamic Impact Methodology and Outcomes

For High Energy Dynamic Impact (HEDI) events, testing to evaluate the structural response of primary aircraft structure for design and certification is both expensive and time consuming. This paper discusses current work seeking to assess, develop, and validate appropriate analytical models that accurately predict physical response, damage, and failure modes for large scale composite structures in HEDI events. Four state-of-the-art Progressive Damage Analysis (PDA) methods were employed for this phased project: LS-DYNA MAT162, LS-DYNA MAT261, Smoothed Particle Galerkin (SPG), and EMU Peridynamics. Multiple material systems were considered, namely T700/5208 textile-infusion triaxial braid, T800/AMD-825 textile-infusion triaxial braid, IM7/8552 uni-directional tape, and SPG 196-PW/8552 plain-weave fabric. Extensive ballistic impact testing was performed to support this activity and measured results were compared to predictive models for assessment using panel delamination, panel displacement, force at the load cells, and threshold velocity as measures. Ultimately, the work under this activity provided significant progress in advancing the state-of-the-art in the use of PDA for HEDI events. Each material model had favorable performance comparing to test in some parameters and needed improvement in others. With the lessons learned from this activity, significant progress was made in the ability to predict panel behavior for a more general case beyond the flat panel in a ballistic impact event. Subsequent Phase II of the NASA ACC HEDI effort will continue to build on the coupon testing, flat panel ballistic impact testing, and analysis performed to-date with application of the PDA methods for intended material selections to test articles with greater complexity of configuration, curvature, and scale. It is not the intention of this paper to present a full set of data, but rather to give an overview of the NASA HEDI effort and show a small representative subset of the test and analysis results.

Hunziker, Kenneth J.↗

NASA NTRS2018

Preparation for Hollow Cathode Testing for the Advanced Electric Propulsion System at NASA Glenn Research Center

NASA Glenn Research Center is performing activities to support the unique needs of hollow cathode development and testing for the Advanced Electric Propulsion System (AEPS). Three existing vacuum facilities have been outfitted as cathode test facilities, and each will serve a different role in upcoming testing. Vacuum Facility 67 is being developed to serve as a long-duration test facility for the Engineering Development Unit cathode, which is to be delivered by the AEPS contractor. It will feature a thruster-like magnetic field simulator and cold-cycle capability via a liquid nitrogen-cooled cold plate. Vacuum Facility 17 is being developed as a test facility for short- to medium-duration experiments in order to provide auxiliary support for the long-duration testing. It will feature a magnetic field simulator but not cold-cycling. Finally, Vacuum Facility 1 will be a high-pumping speed cathode development environment, and will feature an array of plasma and temperature diagnostics. In addition to the facility preparation work, a new cathode, referred to as the Mark II, has been designed. The Mark II is an evolution of the Technology Demonstration Unit cathodes that better evokes the geometry, fabrication, and construction of the forthcoming Engineering Development Unit. This cathode serves as a transition between the Technology Demonstration Unit cathodes used during early thruster development and the forthcoming Engineering Development Unit cathodes. It will be used as a means of verifying the new test facilities prior to arrival of Engineering Development Unit hardware. Details of the Mark II design and key features are presented, as well as details of future work to be performed.

Hall, Scott J.↗

NASA NTRS2018

Preparation for Hollow Cathode Testing for the Advanced Electric Propulsion System at NASA Glenn Research Center

NASA Glenn Research Center is performing activities to support the unique needs of hollow cathode development and testing for the Advanced Electric Propulsion System (AEPS). Three existing vacuum facilities have been outfitted as cathode test facilities, and each will serve a different role in upcoming testing. Vacuum Facility 67 is being developed to serve as a long-duration test facility for the Engineering Development Unit cathode, which is to be delivered by the AEPS contractor. It will feature a thruster-like magnetic field simulator and cold-cycle capability via a liquid nitrogen-cooled cold plate. Vacuum Facility 17 is being developed as a test facility for short- to medium-duration experiments in order to provide auxiliary support for the long-duration testing. It will feature a magnetic field simulator but not cold-cycling. Finally, Vacuum Facility 1 will be a high-pumping speed cathode development environment, and will feature an array of plasma and temperature diagnostics. In addition to the facility preparation work, a new cathode, referred to as the Mark II, has been designed. The Mark II is an evolution of the Technology Demonstration Unit cathodes that better evokes the geometry, fabrication, and construction of the forthcoming Engineering Development Unit. This cathode serves as a transition between the Technology Demonstration Unit cathodes used during early thruster development and the forthcoming Engineering Development Unit cathodes. It will be used as a means of verifying the new test facilities prior to arrival of Engineering Development Unit hardware. Details of the Mark II design and key features are presented, as well as details of future work to be performed.

Advanced Electric Propulsion System (AEPS)↗

NASA NTRS2018

Test and Analysis of Full-Scale 27.5-Foot-Diameter Stiffened Metallic Launch Vehicle Cylinders

The Shell Buckling Knockdown Factor Project (SBKF) was established with the goal of developing improved (i.e., less-conservative, more robust) shell buckling knockdown factors (KDFs) for modern launch-vehicle structures. To this end, SBKF has engaged in several activities to support the development, validation, and implementation of the new design factors, including subscale and full-scale structural testing. Tests on eight different subscale, 8-foot-diameter, integrally stiffened aluminum-lithium 2195 (Al-Li 2195) cylinders were conducted in order to obtain the majority of the required validation data. In addition, two full-scale, 27.5-foot-diameter, Al-Li 2195, integrally stiffened cylinders were tested to provide additional validation data and to determine structural scaling trends. Presented herein are the details of a recent analysis model development and test and analysis correlation effort on the full-scale test articles. The effects of selected modeling assumptions and approaches are discussed, and results from a modeling sensitivity study are presented. It was found that simplified finite element models, that assume nominal test article geometry and material properties, can predict the overall response characteristics well. However, several discrepancies in the test and analysis results were observed. A sensitivity study was performed to determine the effects of several modeling assumptions and address the observed discrepancies. The results from the study indicated that the evolution of local skin pocket buckling and the presence of residual stresses due to the manufacturing process can have a significant influence on the predicted buckling response of the cylinders considered.

Lovejoy, Andrew E.↗

NASA NTRS2018

Preparation for Hollow Cathode Testing for the Advanced Electric Propulsion System at NASA Glenn Research Center

NASA Glenn Research Center is performing activities to support the unique needs of hollow cathode development and testing for the Advanced Electric Propulsion System (AEPS). Three existing vacuum facilities have been outfitted as cathode test facilities, and each will serve a different role in upcoming testing. Vacuum Facility 67 is being developed to serve as a long-duration test facility for the Engineering Development Unit cathode, which is to be delivered by the AEPS contractor. It will feature a thruster-like magnetic field simulator and cold-cycle capability via a liquid nitrogen-cooled cold plate. Vacuum Facility 17 is being developed as a test facility for short- to medium-duration experiments in order to provide auxiliary support for the long-duration testing. It will feature a magnetic field simulator but not cold-cycling. Finally, Vacuum Facility 1 will be a high-pumping speed cathode development environment, and will feature an array of plasma and temperature diagnostics. In addition to the facility preparation work, a new cathode, referred to as the Mark II, has been designed. The Mark II is an evolution of the Technology Demonstration Unit cathodes that better evokes the geometry, fabrication, and construction of the forthcoming Engineering Development Unit. This cathode serves as a transition between the Technology Demonstration Unit cathodes used during early thruster development and the forthcoming Engineering Development Unit cathodes. It will be used as a means of verifying the new test facilities prior to arrival of Engineering Development Unit hardware. Details of the Mark II design and key features are presented, as well as details of future work to be performed.

Hall, Scott J.↗

NASA NTRS2018

Health Monitoring and Prognostics for More Electric Aircrafts

As more and more electric vehicles emerge in our daily operation progressively, a very critical challenge lies in the prediction of remaining flying time/distance (for aircraft). This information is important, particularly in the case of unmanned vehicles, because such vehicles can become self-aware, autonomously compute its own capabilities, and identify how to best plan and successfully complete vehicular missions safely. In case of electric aircrafts, computing remaining flying time is also safety-critical, since an aircraft that runs out of battery charge while in the air will eventually lose control leading to catastrophe. In order to tackle and solve the prediction problem, it is essential to have awareness of the current state and health of the system, especially since it is necessary to perform condition-based predictions. To be able to predict the future state of the system, it is also required to possess knowledge of the current and future operations of the vehicle. Given models of the current and future system behavior, the general approach of model-based prognostics can be employed as a solution to the prior stated prediction problem.For electric aircraft, propulsion is based on power generated from batteries. Thus, it is critical to monitor battery state charge and to estimate the ability of the battery to support mission activities as it is being discharged during flight operation. The ability of the vehicle to complete its given mission very much depends on the charge left in the batteries based on its operational route, maneuvering, weather conditions along with aging health of the batteries. Hence, for the purpose this discussion, consider the scenario of an unmanned electric aircraft that has some planned sequence of waypoints to reach throughout its mission. In such a scenario, for this particular aircraft, and within the region it is flown, at most two minutes are required to safely land the aircraft. Thus, it is desired to predict at which point in time the aircraft must begin to head to the runway and land.

Goebel, Kai↗