Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Route optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

From Pyrolysis Oil to Advanced Biographite Anode: Unravelling Biocoke Structural Evolution and Delayed Coking Effects

Catalytic graphitization of biomass-derived carbon offers a promising route to produce biographite as a sustainable alternative to petroleum-based synthetic graphite for lithium-ion battery (LIB) anodes. This study investigates the physicochemical properties of biocokes produced from pyrolysis oil at carbonization temperatures ranging from 150 degrees C to 500 degrees C. Using an iron (Fe) catalyst, graphitization was performed at 1500 degrees C, significantly lower than the ~3000 degrees C required for conventional synthetic graphite. The effects of introducing an intermediate-temperature hold (400 degrees C-600 degrees C) prior to graphitization were evaluated, simulating a "delayed coking" process to enable the coproduction of sustainable aviation fuels (SAFs). Chemical structure evolution during biocoke formation was analyzed, and proposed mechanisms are presented. Biographites produced via the delayed coking pathway exhibited high crystallinity and excellent electrochemical performance in both half-cell and full-cell LIB configurations. The full cells exhibited an initial discharge capacity close to the theoretical capacity of the NMC622 cathode (175 mAh/g at 4.2 V), and high capacity retention (~88%) after 150 cycles. Notably, the graphitic and electrochemical properties remained stable across the range of intermediate hold temperatures. These findings provide a foundation for optimizing temperature parameters in delayed coking systems to enable scalable, integrated production of biographite and SAFs from pyrolysis oil.

09 BIOMASS FUELS↗
DOE OSTI2023

Carbon-Assisted, Continuous Syngas Production in a Chemical Looping Scheme

In the current energy and environment scenario, it is imperative to develop energy efficient routes for chemical manufacturing that also pave the way for mitigation of greenhouse gas emissions. This work presents an efficient pathway for continuous syngas production via a chemical looping conversion of the two most potent greenhouse gases—CH 4 , and CO 2 . The well-known dry-reforming process of converting CH 4 , and CO 2 to syngas is energy-intensive and suffers from catalyst deactivation. The chemical looping approach, on the other hand, provides avenues for mitigating catalyst deactivation and enabling improved energy efficiency. The key to such process enhancements lies in the intricate structure–function relationships of the catalyst and its correlation to the process variables. We present the reduction and oxidation characteristics of 5 wt.% Ni/Ce 1-x Zr x O 2 -based catalysts (x = 0, 0.4, and 0.625). We demonstrate low temperature CH4 activation over Ni-promoted samples as opposed to pure Ce 1-x Zr x O 2 . Moreover, our results depict an optimum regeneration of these catalysts when oxidized by CO 2 , and H 2 O, which allows for chemical looping operation of steam reforming of methane as well. Process variables were tuned to optimize the CH 4 conversion (over 80%), and H 2 /CO ratio at 650 °C. The critical surface reactions—carbon accumulation and gasification, and thermocatalytic CO 2 splitting were investigated to elucidate the dynamic nature of the catalyst surface. In conclusion, the impact of this work lies in showcasing the opportunities to design chemical looping reactors for energy efficient syngas production from waste greenhouse gases.

25 ENERGY STORAGE↗
DOE OSTI2012

A Novel, ;Double-Clamp; Binding Mode for Human Heme Oxygenase-1 Inhibition

The development of heme oxygenase (HO) inhibitors is critical in dissecting and understanding the HO system and for potential therapeutic applications. We have established a program to design and optimize HO inhibitors using structure-activity relationships in conjunction with X-ray crystallographic analyses. One of our previous complex crystal structures revealed a putative secondary hydrophobic binding pocket which could be exploited for a new design strategy by introducing a functional group that would fit into this potential site. To test this hypothesis and gain further insights into the structural basis of inhibitor binding, we have synthesized and characterized 1-(1H-imidazol-1-yl)-4,4-diphenyl-2-butanone (QC-308). Using a carbon monoxide (CO) formation assay on rat spleen microsomes, the compound was found to be {approx}15 times more potent (IC{sub 50} = 0.27{+-}0.07 {mu}M) than its monophenyl analogue, which is already a potent compound in its own right (QC-65; IC{sub 50} = 4.0{+-}1.8 {mu}M). The crystal structure of hHO-1 with QC-308 revealed that the second phenyl group in the western region of the compound is indeed accommodated by a definitive secondary proximal hydrophobic pocket. Thus, the two phenyl moieties are each stabilized by distinct hydrophobic pockets. This 'double-clamp' binding offers additional inhibitor stabilization and provides a new route for improvement of human heme oxygenase inhibitors.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2015

Succinate Overproduction: A Case Study of Computational Strain Design Using a Comprehensive Escherichia coli Kinetic Model

Computational strain-design prediction accuracy has been the focus for many recent efforts through the selective integration of kinetic information into metabolic models. In general, kinetic model prediction quality is determined by the range and scope of genetic and/or environmental perturbations used during parameterization. Here, we apply the k-OptForce procedure on a kinetic model of E. coli core metabolism constructed using the Ensemble Modeling (EM) method and parameterized using multiple mutant strains data under aerobic respiration with glucose as the carbon source. Minimal interventions are identified that improve succinate yield under both aerobic and anaerobic conditions to test the fidelity of model predictions under both genetic and environmental perturbations. Under aerobic condition, k-OptForce identifies interventions that match existing experimental strategies while pointing at a number of unexplored flux re-directions such as routing glyoxylate flux through the glycerate metabolism to improve succinate yield. Many of the identified interventions rely on the kinetic descriptions that would not be discoverable by a purely stoichiometric description. In contrast, under fermentative (anaerobic) condition, k-OptForce fails to identify key interventions including up-regulation of anaplerotic reactions and elimination of competitive fermentative products. This is due to the fact that the pathways activated under anaerobic condition were not properly parameterized as only aerobic flux data were used in the model construction. This study shed light on the importance of condition-specific model parameterization and provides insight on how to augment kinetic models so as to correctly respond to multiple environmental perturbations.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2015

Formation pathway, structural characterization and optimum processing parameters of synthetic topaz – Al{sub 2}SiO{sub 4}(OH,F){sub 2} – by CVD

A novel synthesis route for topaz (Al{sub 2}SiO{sub 4}(OH,F){sub 2}) by chemical vapor deposition (CVD) using Na{sub 2}SiF{sub 6} as solid precursor was developed. Synthesis tests were conducted with and without a flow of nitrogen, positioning the Al(OH){sub 3} substrate at 0° and 90° with respect to the gas flow direction, at 700 and 750 °C, for 60 and 90 min, respectively. It was found that topaz is synthesized through two pathways, directly and indirectly, involving a series of endothermic and exothermic, heterogeneous and homogeneous reactions between Al(OH){sub 3} and SiF{sub 4}(g). Analytical structural determination confirmed existence of orthorhombic polycrystals with lattice parameters of a =4.6558 Å, b=8.8451 Å and c=8.4069 Å. According to ANOVA, while temperature, time and interaction of substrate angular position with atmosphere (P×A) are the parameters that most significantly influence the variability in the amount of topaz formed – equivalent contributions of 31% – topaz lattice parameters are mostly impacted by the same factors (T, t, P, A), but without the interaction factor. The projected amount of topaz is in good agreement with that obtained in confirmation tests under optimal conditions: Al(OH){sub 3} substrate compact placed at 0°, treated at 750 °C for 90 min in the absence of N{sub 2}. - Highlights: • Topaz synthesis as a unique phase by CVD, using solid precursor Na{sub 2}SiF{sub 6} is feasible. • Two pathways, a series of endothermic/exothermic, heterogeneous/homogeneous reactions. • Crystal structure, orthorhombic polycrystals: a =4.6558 Å, b=8.8451 Å, c=8.4069 Å. • Anova: amount of topaz formed and lattice parameters are impacted by same factors. • Projection of topaz quantity in good agreement with those from confirmation tests.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Substituted ALPO-5 Zeolites as Promising O 2 Sorption Pump Materials: A Density Functional Theory Study

Many chemical processes depend on having an environment that is low in oxygen partial pressure (P O2 < 100 Pa); sorption pumps are a promising route to establishing that environment by either oxygen pumping or oxygen separation from an inert gas. Near ambient sorption-based processes rely on either pressure or thermal swings, requiring no moving parts, no electricity, and neither very high nor very low temperatures. In this work, we use ab initio calculations to explore zeolites as a class of materials for sorption based oxygen pumping/separation. Our calculations indicate that while the neat ALPO-5 zeolite does not adsorb O 2 , O 2 does adsorb on zeolites selectively substituted with transition metals and metalloids and hence, can enable separation and pumping. ALPO-5 substituted with Si, Ge, Sn, Pd, Pt, Ti, V, Cr, Mn, Zr, Mo, Hf, W, Ce, and Pr provides adsorption energies ranging from -0.19 to -3.92 eV, (-) indicates exothermic process. Additionally, we provide a comprehensive understanding of what controls the adsorption energy: 1) the substi-tutions must be able to adopt an oxidation state that is more positive than the cation it replaces, and 2) the size of the pore into which the O 2 adsorbs to the wall. Additionally, we conduct a ther-modynamic analysis of a thermal swing cycle to approximate the optimal O 2 binding energy for 2 low energy O 2 pumping/separation. We find that the minimum energy cost likely occurs when the adsorption energy is in the range of 0.75 – 1.00 eV (72 – 97 kJ·mol -1 ), which corresponds to Ge, V, Pt, or Ce substituted ALPO-5.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Polyoxometalates as bifunctional templates: engineering metal oxides with mesopores and reactive surfaces for catalysis

Mesoporous metal oxides with optimized porosity and active surfaces usually exhibit unexpected performance in many applications. However, sacrificial templates and complicated processes are generally required to generate mesopores. Herein, we discover the bifunctional templating talent of polyoxometalates (POMs) for generating not only mesopores but also reactive surfaces in metal oxides, and a facile, recyclable, and general method is reported. By mechanochemical ion-sharing between metal salts and POMs, metal precursors undergo pyrolysis around large POM clusters, which can incorporate abundant mesopores into metal oxides ( e.g. , Co 3 O 4 , Fe 3 O 4 , NiO, La 2 O 3 , MnO 2 , CeO 2 , ZrO 2 , and CuO) with ultrahigh specific surface areas (up to 210 m 2 g -1 ) after simply being recycled by water washing. Unexpectedly, the oxidative feature of POMs naturally contributes to the formation of high valence metal cations on the material surface. Therefore, as an example, the Co 3 O 4 sample with both mesopores and enriched surface Co 3+ species was more active than Co 3 O 4 derived from a silica template ( T 100 = 200 °C) and commercial Co 3 O 4 ( T 100 = 250 °C), in CO oxidation. The current strategy may provide a promising route for the commercialization of mesoporous metal oxides with preferred surface features.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Systems Based Approaches for Thermochemical Conversion of Biomass to Bioenergy and Bioproducts

Auburn’s Center for Bioenergy and Bioproducts conducts research on production of synthesis gas for use in power generation and the production of liquid fuels. The overall goal of our gasification research is to identify optimal processes for producing clean syngas to use in production of fuels and chemicals from underutilized agricultural and forest biomass feedstocks. This project focused on construction and commissioning of a bubbling-bed fluidized-bed gasifier and subsequent shakedown of the gasification and gas cleanup system. The result of this project is a fully commissioned gasification laboratory that is conducting testing on agricultural and forest biomass. Initial tests on forest biomass have served as the foundation for follow-up studies on gasification under a more extensive range of temperatures, pressures, and oxidant conditions. The laboratory gasification system consists of a biomass storage tank capable of holding up to 6 tons of biomass; a biomass feeding system, with loss-in-weight metering system, capable of feeding biomass at pressures up to 650 psig; a bubbling-bed fluidized-bed gasification reactor capable of operating at pressures up to 650 psig and temperatures of 1500oF with biomass flowrates of 80 lb/hr and syngas production rates of 37 scfm; a warm-gas filtration system; fixed bed reactors for gas conditioning; and a final quench cooling system and activated carbon filtration system for gas conditioning prior to routing to Fischer-Tropsch reactors, or storage, or venting. This completed laboratory enables research to help develop economically feasible technologies for production of biomass-derived synthesis gases that will be used for clean, renewable power generation and for production of liquid transportation fuels. Moreover, this research program provides the infrastructure to educate the next generation of engineers and scientists needed to implement these technologies.

09 BIOMASS FUELS↗
DOE OSTI2025

Origin of Large Effective Phonon Magnetic Moments in Monolayer MoS 2

Recent helicity-resolved magneto-Raman spectroscopy measurement demonstrates large effective phonon magnetic moments of ~2.5 μ B in monolayer MoS 2 , highlighting resonant excitation of bright excitons as a feasible route to activate Γ-point circularly polarized phonons in transition metal dichalcogenides. However, a microscopic picture of this intriguing phenomenon remains lacking. In this work, we show that an orbital transition between the split conduction bands (Δ 0 = 4 meV) of MoS 2 couples to the doubly degenerate E" phonon mode (Ω 0 = 33 meV), forming two hybridized states. Our phononic and electronic Raman scattering measurements capture these two states: (i) one with predominantly phonon contribution in the helicity-switched channels and (ii) one with primarily orbital contribution in the helicity-conserved channels. An orbital-phonon coupling model successfully reproduces the large effective magnetic moments of the circularly polarized phonons and explains their thermodynamic properties. Strikingly, the Raman mode from the orbital transition is superimposed on a strong quasi-elastic scattering background, indicating the presence of spin fluctuations. As a result, the electrons excited to the conduction bands through the exciton exhibit paramagnetic behavior although MoS 2 is generally considered as a nonmagnetic material. By depositing nanometer-thickness nickel thin films on monolayer MoS 2 , we tune the electronic structure so that the A exciton perfectly overlaps with the 633 nm laser. The optimization of resonance excitation leads to pronounced tunability of the orbital-phonon hybridized states. Our results generalize the orbital-phonon coupling model of effective phonon magnetic moments to material systems beyond the paramagnets and magnets.

2D transition metal dichalcogenide↗
DOE OSTI2023

Minimal Energy Routing of a Leader and a Wingmate with Periodic Connectivity

We consider a route planning problem in which two unmanned vehicles are required to complete a set of tasks present at distinct locations, referred to as targets, with minimum energy consumption. The mission environment is hazardous, and to ensure a safe operation, the UVs are required to communicate with each other at every target they visit. The problem objective is to determine the allocation of the tasks to the UVs and plan tours for the UVs to visit the targets such that the weighted sum of the distances traveled by the UVs and the distances traveled by the communicating signals between them is minimized. We formulate this problem as an Integer program and show that naively solving the problem using commercially available off-the-shelf solvers is insufficient in determining scalable solutions efficiently. To address this computational challenge, we develop an approximation and a heuristic algorithm, and employ them to compute high-quality solutions to a special case of the problem where equal weights are assigned to the distances traveled by the vehicles and the communicating signals. For this special case, we show that the approximation algorithm has a fixed approximation ratio of 3.75. We also develop lower bounds to the optimal cost of the problem to evaluate the performance of these algorithms on large-scale instances. We demonstrate the performance of these algorithms on 500 randomly generated instances with the number of targets ranging from 6 to 100, and show that the algorithms provide high-quality solutions to the problem swiftly; the average computation time of the algorithmic solutions is within a fraction of a second for instances with at most 100 targets. Finally, we show that the approximation ratio has a variable ratio for the weighted case of the problem. Specifically, if ρ denotes the ratio of the weights assigned to the distances representing the communication and travel costs, the algorithm has an a posteriori ratio of $3 + \frac{3ρ}{4}$ when ρ ≥ 1, and $\frac{3}{ρ}$ + $\frac{3}{4}$ when ρ ≤ 1.

42 ENGINEERING↗
DOE OSTI2025

Helium recovery system at IB3a

The increasing need for optimal and sustainable use of cryogenic resources to support Fermilab’s scientific mission has highlighted the necessity of improving the Laboratory’s helium management practices. An assessment of cryogenic test facilities identified the Technical Division’s Industrial Building 3a (IB3A) as a key site requiring upgrades to integrate a helium recovery system. The IB3A facility is essential for characterizing and testing superconductors, cables, and coils for various R&D projects, including the US High-Luminosity LHC Accelerator Upgrade Project (AUP), Mu2e, and other external collaborations. Currently, the facility relies on 500 L helium Dewars and vents the vaporized helium directly into the atmosphere, leading to significant helium loss. Given the non-renewable nature of helium, recovering and reusing this resource is critical for the sustainability of Fermilab’s operations. To address this challenge, a project has been initiated to connect IB3A to an existing helium purification station and refrigeration system located in another building via a dedicated pipeline pass over the roof of several buildings. This solution will enable the efficient capture of vented helium, its transfer to the purification station, and subsequent liquefaction for reuse in future operations. The project includes a detailed design phase, specifying the pipeline route, flow control mechanisms, and integration with the existing cryogenic infrastructure, followed by phased implementation and commissioning. By implementing this pipeline connection and upgrading IB3A, Fermilab aims to significantly reduce helium waste, lower operational costs, and align with its commitment to sustainability. This initiative provides a model for resource-efficient cryogenic operations and reinforces the Laboratory’s capacity to support its science mission for the long term.

Porwisiak, D. [Fermilab]↗
DOE OSTI2022

Deciphering the Mechanistic Role of Individual Oxide Phases and Their Combinations in Supported Mn–Na 2 WO 4 Catalysts for Oxidative Coupling of Methane

Oxidative coupling of methane (OCM) is an attractive direct route for upgrading methane to valuable chemicals. In this study, Temporal Analysis of Products (TAP) and steady state experiments are conducted to understand the role of individual oxide phases and their combinations in supported Mn-Na 2 WO 4 /SiO 2 catalysts for OCM. The results from TAP transient kinetic studies indicate that Mn plays an important role in promoting gas phase oxygen activation, while NaO x /SiO 2 and WO x /SiO 2 are relatively inert towards gas phase oxygen and methane activation. However, the supported catalyst combining Na and W in the form Na 2 WO 4 show enhanced gas phase oxygen activation exhibiting a much lower oxygen activation energy (148 kJ/mol) and enhanced activity toward methane activation as compared to the individual supported oxide catalysts. Addition of Mn to Na 2 WO 4 /SiO 2 further decreases the oxygen activation energy by 40 kJ/mol. Moreover, methane activation is also enhanced with CH 3 as the main intermediate but, with increasing Mn content, more CH 2 intermediates are observed. Different forms of oxygen (both dioxygen and atomic) are detected on the catalyst surface using isotopic pump/probe pulsing and their distribution is found to depend on the catalyst composition. An optimal Mn content in the Na 2 WO 4 /SiO 2 catalyst system is needed to enhance the amount of dioxide surface species (e.g., superoxide 16 O 2 - or peroxide 16 O 2 2- ) associated with the Na 2 WO 4 leading to high C 2 selectivity for OCM. When the Mn content is too high, the larger MnOx domains are shown to contribute to the formation of higher concertation of monoxide surface species that lead to nonselective OCM pathways. This insight from transient kinetic characterization using TAP combined with conventional steady state studies, provides a deeper understanding of the role of individual oxide phases and their combination on supported catalysts toward the formation of intermediate surface species and their impact on the OCM reaction mechanism. This knowledge is critical toward designing superior catalyst formulations for OCM.

10 SYNTHETIC FUELS↗
DOE OSTI2025

Diagnostics: Chapter 8 of the special issue: on the path to tokamak burning plasma operation

This chapter presents the activity conducted by the ITPA topical group (TG) on Diagnostics over about the last 15 years. Following a general introduction of the ITER Diagnostics led by their measurement roles, the document is organized in several subchapters detailing the design support, research and development activity conducted by each of the specialist working groups (WGs) of the TG. Please note that the magnetic diagnostics were supported at the TG without a specific WG. Their status is included in the general introduction. In the following some highlights of the subchapter’s contents are provided. Recent advances in ITER first wall (FW) diagnostics for the measurements of plasma-metallic wall interaction in support of the ITER research plan are reported. An InfraRed imaging Video Bolometer for ITER has been developed and tested on several tokamaks to measure the radiated power loss. A laser-induced breakdown spectroscopy (LIBS) technique which utilizes a pulsed laser beam to ablate locally by forming a crater, will measure local tritium inventory in the FW material. Real-time Residual Gas Analyzers will measure the neutral gas composition in a divertor port and an equatorial port during plasma operation. Due to the full metallic FW environment, the plasma-wall interaction in ITER will face several challenges such as the compromised radiated power and divertor heat flux measurements by reflection. Ray tracing and analysis codes have been developed to eliminate and correct the effects of reflection in the measurements. The characteristics of the reflecting surfaces depending on the roughness and angle of the incidence have been measured by dedicated experiments, and the results were applied to the reflection elimination. For the measurement of the metallic impurity radiation induced by eroded metallic atoms, a vacuum ultraviolet spectrometer has been developed and tested. An extensive thermonuclear diagnostic suite will be required to support the operation of ITER and the planned experimental program for future burning plasma experiments. Due to the harsh environmental conditions, the implementation of diagnostic systems in ITER is a major challenge. These conditions include high levels of neutron and gamma fluxes, neutron heating, particle bombardment. Therefore, the selection and design of diagnostic systems must take into account a number of phenomena previously unseen in diagnostic design. For this reason, the measurement of neutrons and confined or lost fast ions, with particular emphasis on alpha particles, is critical to ITER. The diagnostics associated with these measurements will be important for future plasma-burning experiments at ITER. The high neutron emission and very large plasma size in ITER make neutron diagnostics the main diagnostic method used to measure plasma parameters such as fusion power, fusion power density, ion temperature, energy of fast ions and their spatial distributions in the plasma core. Active spectroscopy techniques are methods where a neutral particle beam is injected into the plasma and information on plasma parameters is extracted from the measurement of line emission resulting from the beam-plasma interaction, either by plasma ions or by beam atoms. Spatial localization is achieved by crossing the beamline and multiple observation lines. The ITER plasma will be a high temperature, moderately dense, fully ionized collisional plasma. The plasma facing surfaces are principally metallic being fashioned from beryllium or tungsten but many other elements, arising from either structural or from operational needs, may enter this plasma. The energy range of the emitted photons range from meV (infra-red) to multi keV (x-rays) and originate from all areas of the plasma volume. The primary role of passive emission diagnostics is to identify what is in the plasma from spectral signatures. Extracting quantitative information from these measurements such as impurity content, ion temperature, rotation, degree of detachment and radiated power depends on calibrated instruments, a physics model of the atomic and molecular processes and plasma transport and an analysis workflow that takes into account environmental effects such as reflections. The particular needs for ITER have prompted a multi-machine, many-year effort to address all these aspects and this chapter reviews the work on diagnostic design, experiments and new analysis techniques. An overview of the laser diagnostics to be implemented on ITER is also provided in this paper. This includes descriptions of the Thomson scattering in the core, edge and divertor regions, polarimetry and interferometry diagnostics used for measuring plasma density and also measurements of helium density in the divertor using Laser Induced Flourescence. Techniques which can allow improvements on current measurements are also addressed in particular expanding poloidal polarimetry measurements to measure field fluctuations and proposed use of dispersion interferometery which has a number of advantages over existing methods. This paper identifies particular areas where further research and testing on existing tokamaks is useful even at this advanced stage to inform the design of diagnostics for ITER. Outstanding areas of concern for the implementation of laser diagnostics, in particular with a view to reliable operation are identified. An overview of the latest developments of microwave diagnostic systems and techniques is given. The primary focus is the contributions for ITER—the next step burning plasma experiment—which is supplemented by describing recent progress of techniques applicable for fusion experiments beyond ITER. The contributions are intentionally kept concise, and are being supplemented by a rich list of references for further studies. Radiation induced effects are receiving continuous and well-deserved attention of the ITER diagnostic community and they are in many cases one of the primary design drivers of the ITER diagnostic systems. The paper summarizes recent progress in this area focusing primarily on the ITER diagnostics but in some cases provides also outlook for the possible solutions for even more demanding radiation environment of fusion reactors beyond ITER. Despite advancements in the area of modeling and simulation of various radiation induced effects, experimental testing in a nuclear environment as close as possible to the target one is still seen as unavoidable for proper qualification of particular diagnostic functional elements. Recent advancement within three diagnostic areas: optical diagnostics, magnetics and bolometers is covered. Encouraging results on qualification of silica glass vacuum window assemblies are presented. In the area of magnetic sensors, progress of irradiation tests performed on ITER in-vessel LTCC inductive sensors is presented with outlook for novel technological approaches to inductive sensors utilizing thick printing and photolithography technologies being highlighted. Summary of advancements in the area of steady state magnetic field sensors based on Hall effect is given. New results of neutron irradiation test of the ITER borosilicate glass inserts for vacuum electrical feedthroughs are summarized finding negligible swelling at target level of neutron fluence. Off-line irradiation tests of fiber optic current sensors for plasma current measurement demonstrated that both for gamma doses up to 5 MGy and a total neutron fluence up to 10 15 cm −2 , radiation induced changes are still compatible with required measurement accuracy on ITER. The ITER bolometers are given as an example how considering radiation effects may influence the diagnostic design. Finally, outlook for future main R&D directions is outlined. All optical and laser-based diagnostics in ITER will be using mirrors to guide plasma radiation toward detectors, cameras and sensors. In the hostile plasma, radiation and particle environment the optical characteristics of diagnostic mirrors will degrade directly affecting the entire performance of involved diagnostic systems. An assessment of factors affecting mirror performance is provided. Among the prime adverse factors are deposition of plasma impurities, sputtering of mirror surface and steam ingress in the vicinity of mirrors. Within the International Tokamak Physics Activity with active support by ITER central team and domestic agencies, the structured research and development (R&D) program on mitigation of risks for diagnostic mirrors is underway. Within this program the mirror material development, the passive mitigation of mirror degradation by using diagnostic ducts and shutters along with an active mirror recovery program comprising the in-situ mirror cleaning and calibration is underway. Recent developments in diagnostic mirror R&D are described in this Chapter along with an example of their implementation of R&D solutions in ITER Infrared Thermography diagnostic. An assessment of still open engineering and physics questions, considerations on mirror risks during an early phase of ITER operation are given along with an overview of diagnostic mirror evolution in the late ITER operation stage toward the demonstration fusion power plant. Several crucial areas of diagnostic R&D outlined in ITER Research Plan are addressed. The basic control groups in a fusion reactor can be broken-down in five categories: (1) plasma position, magnetic configuration, and plasma current control, (2) profile control and confinement optimization, (3) MHD control and suppression, (4) edge dissipation control, radiation and plasma exhaust control and (5) break-down optimization. These categories are coupled via the physics (a control action in one domain will affect the other domains) and via shared actuators (e.g. ECRH for impurity accumulation avoidance, current density distribution control and MHD suppression). Consequently, a supervisory control system should determine the priority of the various control tasks, their couplings, and the interfaces with the safety and interlock system. For the systematic development of the various controllers taking the complexity of the plasma and the control system into account, a model-based approach is required. A short historical overview is given of the developments in systems and control theory and control engineering with special emphasis on those developments that are most relevant for Nuclear Fusion research and operation. An overview is given of the state of the field of fusion plasma control for the control categories. It will be shown how synthetic diagnostics are being developed in ITER and how they are used in diagnostic design and design validation and how they can be in model-based controller synthesis using relatively simple models. In modern control methods, multiple diagnostics are used to constrain relatively simple models. The constrained models provide an estimate for the state. This opens the route to state controllers, such as model predictive control. A major challenge in nuclear fusion research is the coherent combination of data from heterogeneous diagnostics and modeling codes for machine control and safety as well as physics studies. Measured data from different diagnostics often provide information about the same subset of physical parameters. Additionally, information provided by some diagnostics might be needed for the analysis of other diagnostics. A joint analysis of complementary and redundant data allows, e.g. to improve the reliability of parameter estimation, to increase the spatial and temporal resolution of profiles, to obtain synergistic effects, to consider diagnostics interdependencies and to find and resolve data inconsistencies. Physics-based modeling and parameter relationships provide additional information improving the treatment of ill-posed inversion problems. A coherent combination of all kind of available information within a probabilistic framework allows for improved data analysis results. The concept of integrated data analysis (IDA) in the framework of Bayesian probability theory is outlined and contrasted with conventional data analysis. Components of the probabilistic approach are summarized and specific ingredients beneficial for data analysis at fusion devices are discussed.

ITER↗
DOE OSTI2020

Repair and Resource Scheduling in Unbalanced Distribution Systems Using Neighborhood Search

—This paper proposes an optimization strategy to assist utility operators to recover power distribution systems after large outages. Specifically, a mixed-integer linear programming (MILP) model is developed for co-optimizing crews, resources, and network operations. The MILP model coordinates damage isolation, network reconfiguration, distributed generator re-dispatch, and crew/resource logistics. In addition, a framework for integrating different types of photovoltaic (PV) systems in the restoration process is developed. We consider two different types of crews, namely, line crews for damage repair and tree crews for obstacle removal. We also model the repair resource logistic constraints. Furthermore, a new algorithm is developed for solving the distribution system repair and restoration problem (DSRRP). The algorithm starts by solving DSRRP using an assignmentbased method, then a neighborhood search method is designed to iteratively improve the solution. The proposed method is validated on modified IEEE 123- and 8500-bus distribution test systems.

Outage management↗
DOE OSTI2025

Electrochemical reduction of ammonia-captured CO 2 to CO over a nickel single-atom catalyst

Carbon reactive capture and conversion offers a sustainable route to valuable chemicals and fuels while aiding Green House Gas (GHG) reduction. Direct electrochemical conversion of capture solutions like bicarbonate avoids the energy demands of conventional CO 2 regeneration. Ammonium bicarbonate (NH 4 HCO 3 ) is particularly attractive due to its low decomposition temperature and ability to supply in situ CO 2 from dilute sources without requiring purified CO 2 . Meanwhile, single-atom catalysts (SACs) with nitrogen-coordinated metal sites further enhance CO 2 reduction efficiency using Earth-abundant materials. In this study, we demonstrate a nickel single-atom catalyst (Ni-SAC)-based electrolyzer that utilizes NH 4 HCO 3 as the CO 2 source, achieving significantly improved CO production performance compared to the conventional silver cathodes used in the CO 2 reduction reaction (CO 2 RR) to produce CO. The Ni-SAC cathode exhibited a Faradaic efficiency of 60.1% for CO production at −200 mA cm −2 , while the silver cathode achieved a Faradaic efficiency of only 2%, likely due to ammonium-induced poisoning. Furthermore, the integration of a customized microporous layer onto the electrode significantly increased the Faradaic efficiency from 64% to 83% at −100 mA cm −2 , emphasizing the crucial role of electrode structure optimization in enhancing CO selectivity. These findings demonstrate a sustainable and economically viable strategy for green CO production directly from CO 2 capture solutions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2019

Alternative outlets for sustaining photosynthetic electron transport during dark-to-light transitions

Environmental stresses dramatically impact the balance between the production of photosynthetically derived energetic electrons and Calvin–Benson–Bassham cycle (CBBC) activity; an imbalance promotes accumulation of reactive oxygen species and causes cell damage. Hence, photosynthetic organisms have developed several strategies to route electrons toward alternative outlets that allow for storage or harmless dissipation of their energy. In this work, we explore the activities of three essential outlets associated with Chlamydomonas reinhardtii photosynthetic electron transport: (i) reduction of O 2 to H 2 O through flavodiiron proteins (FLVs) and (ii) plastid terminal oxidases (PTOX) and (iii) the synthesis of starch. Real-time measurements of O 2 exchange have demonstrated that FLVs immediately engage during dark-to-light transitions, allowing electron transport when the CBBC is not fully activated. Under these conditions, we quantified maximal FLV activity and its overall capacity to direct photosynthetic electrons toward O 2 reduction. However, when starch synthesis is compromised, a greater proportion of the electrons is directed toward O 2 reduction through both the FLVs and PTOX, suggesting an important role for starch synthesis in priming/regulating CBBC and electron transport. Moreover, partitioning energized electrons between sustainable (starch; energetic electrons are recaptured) and nonsustainable (H 2 O; energetic electrons are not recaptured) outlets is part of the energy management strategy of photosynthetic organisms that allows them to cope with the fluctuating conditions encountered in nature. Finally, unmasking the repertoire and control of such energetic reactions offers new directions for rational redesign and optimization of photosynthesis to satisfy global demands for food and other resources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2017

Cation–Eutectic Transition via Sublattice Melting in CuInP 2 S 6 /In 4/3 P 2 S 6 van der Waals Layered Crystals

Single crystals of the van der Waals layered ferrielectric material CuInP 2 S 6 spontaneously phase separate when synthesized with Cu deficiency. In this paper, we identify a route to form and tune intralayer heterostructures between the corresponding ferrielectric (CuInP 2 S 6 ) and paraelectric (In 4/3 P 2 S 6 ) phases through control of chemical phase separation. We conclusively demonstrate that Cu-deficient Cu 1–x In 1+x/3 P 2 S 6 forms a single phase at high temperature. We also identify the mechanism by which the phase separation proceeds upon cooling. Above 500 K both Cu + and In 3+ become mobile, while P 2 S 6 4– anions maintain their structure. We therefore propose that this transition can be understood as eutectic melting on the cation sublattice. Such a model suggests that the transition temperature for the melting process is relatively low because it requires only a partial reorganization of the crystal lattice. As a result, varying the cooling rate through the phase transition controls the lateral extent of chemical domains over several decades in size. At the fastest cooling rate, the dimensional confinement of the ferrielectric CuInP 2 S 6 phase to nanoscale dimensions suppresses ferrielectric ordering due to the intrinsic ferroelectric size effect. Finally, intralayer heterostructures can be formed, destroyed, and re-formed by thermal cycling, thus enabling the possibility of finely tuned ferroic structures that can potentially be optimized for specific device architectures.

2D ferrielectric↗
DOE OSTI2012

New fluoroionomer electrolytes with high conductivity and low SO 2 crossover for use in electrolyzers being developed for hydrogen production from nuclear power plants (Final Report)

Thermochemical water splitting cycles, using the heat of nuclear power plants, offer an alternate highly efficient route for the production of hydrogen. Among the many possible thermochemical cycles for the hydrogen production, the sulfur-based cycles lead the competition in overall energy efficiency. A variant on sulfur-based thermochemical cycles is the Hybrid Sulfur (HyS) Process, which uses a sulfur dioxide depolarized electrolyzer (SDE) to produce hydrogen. The Savannah River National Laboratory (SRNL) selected the fuel cell MEA design concept for the SDE in the HyS process since the MEA concept provides a much smaller cell footprint than conventional parallel plate technology. The electrolyzer oxidizes sulfur dioxide to form sulfuric acid at the anode and reduces protons to form hydrogen at the cathode. The overall electrochemical cell reaction consists of the production of H 2 SO 4 and H 2 . There is a significant need to provide the membrane materials that exhibit reduced sulfur dioxide transport characteristics without sacrificing other important properties such as high ionic conductivity and excellent chemical stability in highly concentrated sulfuric acid solutions saturated with sulfur dioxide. As an alternative membrane, sulfonated Perfluorocyclobutyl aromatic ether polymer (sPFCB) were expected to posses low SO 2 permeability due to their stiff backbones as well as high proton conductivity, improved mechanical properties. The major accomplishments of this project were the synthesis, characterizations, and optimizations of suitable electrolyzers for good SDE performance and higher chemical stability against sulfuric acid. SDE performance results of developed sPFCB polyelectrolytes have shown that these membranes exhibit good chemical stability against H 2 SO 4 .

08 HYDROGEN↗