Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHOSPHIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Growth of InP on GaAs (001) by hydrogen-assisted low-temperature solid-source molecular beam epitaxy

Direct heteroepitaxial growth of InP layers on GaAs (001) wafers has been performed by solid-source molecular beam epitaxy assisted by monoatomic hydrogen (H*). The epitaxial growth has been carried out using a two-step method: for the initial stage of growth the temperature was as low as 200 deg. C and different doses of H* were used; after this, the growth proceeded without H* while the temperature was increased slowly with time. The incorporation of H* drastically increased the critical layer thickness observed by reflection high-energy electron diffraction; it also caused a slight increase in the luminescence at room temperature, while it also drastically changed the low-temperature luminescence related to the presence of stoichiometric defects. The samples were processed by rapid thermal annealing. The annealing improved the crystalline quality of the InP layers measured by high-resolution x-ray diffraction, but did not affect their luminescent behavior significantly.

36 MATERIALS SCIENCE↗

High quality InAsSb grown on InP substrates using AlSb/AlAsSb buffer layers

High quality InAsSb grown on semi-insulating InP substrates by molecular beam epitaxy was achieved using AlSb/AlAsSb structure as the buffer layer. A 1000 A InAsSb layer grown on top of 1 {mu}m AlSb/AlAsSb buffer layer showed a room temperature electron mobility of {approx}12 000 cm{sup 2}/V s. High structural quality and low misfit defect density were also demonstrated in the InAsSb layer. This novel AlSb/AlAsSb buffer layer structure with the AlAsSb layer lattice matched to InP substrates could enhance the performance of optoelectronic devices utilizing 6.1 A family of compound semiconductor alloys.

36 MATERIALS SCIENCE↗

Modification of charge compensation in semi-insulating semiconductors by high energy light ion irradiation

High energy light ions have been used to engineer the electrical properties of semi-insulating InP and GaAs by creation and annihilation of native defects. Due to light mass, high energy ions lose most of their energy during flight inside the material by electronic excitation, which also modifies the charge states of the defect. Imbalance in charge compensation caused by irradiation induced defect engineering results in the modification of resistivity of the semi-insulating samples. The activation energies of the defect levels responsible for the modified resistivity have been estimated from the measurement of thermally activated currents. It is shown that the modified charge compensation is due to annihilation and/or creation of native defects depending on the material (GaAs or InP) and the fluence of irradiated ions. It has also been observed that annealing does not have any effect on modified compensation in InP, but in the case of GaAs, compensation recovers after thermal annealing.

36 MATERIALS SCIENCE↗

High crystalline-quality III-V layer transfer onto Si substrate

In this study, an approach combining ion cutting and selective chemical etch for the transfer of high crystalline-quality III-V layers on SiO{sub 2}/Si substrate has been investigated. This layer transfer scheme takes advantage of the ion-cutting process by conserving III-V substrates for reuse and simultaneously improving the transferred layer quality and surface condition without using chemical and mechanical polishing. The relocation of the ion-implantation damage maximum enables the transfer of relatively defect-free InP-based layers onto a Si substrate coated with an oxide layer and results in structures ready for further optoelectronic device fabrication or epitaxial growth.

36 MATERIALS SCIENCE↗

Study of Fast, Near-Infrared Photodetectors for the ITER Core LIDAR Thomson Scattering

A key component for the ITER core LIDAR Thomson Scattering (TS) diagnostic would be a detector with good sensitivity in the 850-1060 nm near infrared (NIR) spectral region. Covering this spectral region becomes necessary if a Nd:YAG laser system operating at {lambda} = 1.06 {mu}m is used as the laser source, which is a very attractive choice in terms of available energy, repetition rate, reliability and cost. In this paper we review the state of the art of two types of detectors available for the above spectral range: the transferred electron (TE) InGaAs/InP hybrid photodiode and the In{sub x}Ga{sub 1-x}As microchannel plate (MCP) image intensifier and we describe the advancements necessary for a possible application in the ITER LIDAR TS. In addition we describe the preliminary characterization of new GaAsP fast MCP photomultipliers (PMTs) suitable for the detection of the visible part of the LIDAR TS spectrum in JET and ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Formation mechanisms of ZnO amorphous layers due to thermal treatment of ZnO thin films grown on p-InP (100) substrates

High-resolution transmission electron microscopy (HRTEM) images, selected-area electron diffraction (SAED) patterns, and energy dispersive x-ray spectroscopy (EDS) profiles showed that P atoms accumulated due to thermal treatment on the top sides and in the heterointerface layers of ZnO thin films grown on p-InP (100) substrates, resulting in the formation of amorphous ZnO layers in the ZnO thin films. The formation mechanisms of the ZnO amorphous layers due to thermal treatment are described on the basis of the HRTEM, the SAED, and the EDS measurements.

36 MATERIALS SCIENCE↗

Impact of feature-size dependent etching on the optical properties of photonic crystal devices

Feature size dependence in Ar/Cl{sub 2} chemically assisted ion beam etching of InP-based photonic crystals (PhCs) and its influence on the optical properties of PhC devices operating in the band gap are investigated. The analysis of the measured quality factors, the determined mirror reflectivities, and losses of one-dimensional Fabry-Perot cavities clearly demonstrates the importance of feature-size dependent etching. The optical properties show a dramatic improvement up to a hole depth of about 3.5 {mu}m that is primarily due to a significant reduction in extrinsic losses. However, beyond this hole depth, the improvement is at a lower rate, which suggests that extrinsic losses, although present, are not dominant.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effects of hydrogen implantation temperature on InP surface blistering

We have investigated the effects of hydrogen implantation temperature on the ion-cut process of InP by examining the correlation between surface blistering and the ion induced damage, hydrogen distribution, and strain. Using Rutherford backscattering spectrometry, elastic recoil detection, and x-ray diffraction, it was found that both the point defects induced by the hydrogen implantation and the in-plane compressive stress were necessary for hydrogen trapping and H-platelet nucleation and growth. The control of implantation temperature is crucial for creating sufficient defects and strain to induce surface blistering or layer exfoliation.

36 MATERIALS SCIENCE↗

Metamorphic approach to single quantum dot emission at 1.55 {mu}m on GaAs substrate

We report on the fabrication and the characterization of InAs quantum dots (QDs) embedded in an indium rich In{sub 0.42}Ga{sub 0.58}As metamorphic matrix grown on a GaAs substrate. Growth conditions were chosen so as to minimize the number of threading dislocations and other defects produced during the plastic relaxation. Sharp and bright lines, originating from the emission of a few isolated single quantum dots, were observed in microphotoluminescence around 1.55 {mu}m at 5 K. They exhibit, in particular, a characteristic exciton/biexciton behavior. These QDs could offer an interesting alternative to other approaches as InAs/InP QDs for the realization of single photon emitters at telecom wavelengths.

36 MATERIALS SCIENCE↗

Integration of thin layers of single-crystalline InP with flexible substrates

Transfer of thin semiconductor layers onto flexible substrates using a combination of ion cutting, adhesive bonding, and laser ablation was investigated. An {approx}1.3 {mu}m thick InP layer was first transferred onto sapphire using adhesive bonding and hydrogen-induced layer exfoliation at {approx}180 deg. C. The resulting structure was then adhesively bonded onto flexible polyethylene naphthalate substrate, followed by UV laser ablation of the first adhesive to separate the initial bond. Additional transfer steps were inserted into the process to enable thermal annealing and electrical recovery. The transferred films were electrically characterized and the potential use in high-speed, flexible electronics is discussed.

36 MATERIALS SCIENCE↗

InAlGaAs/InP light-emitting transistors operating near 1.55 {mu}m

Light-emitting transistors (LETs) operating at around 1.55 {mu}m were investigated using InP/InAlGaAs heterostructures grown by metal organic chemical vapor deposition. By incorporating InGaAs quantum wells (QWs) in the base region of the N-InP/p-InAlGaAs/N-InAlAs heterojunction bipolar transistors, LET structures were achieved with a current gain of 45 and light emission at a wavelength of 1.65 {mu}m. The light output was found to be dependent on the base current. The larger the number of QWs incorporated in the base of the LETs, the larger the light output, with correspondingly reduced current gain. Secondary ion mass spectroscopy shows that the p-type dopant, zinc (Zn), which is commonly used in the growth of InAlGaAs, diffuses into the emitter and the base active QW region, leading to compromised electrical performance and light output intensity. Increasing the Zn doping level in the barrier layers of the QW structure causes the photoluminescence efficiency to decrease rapidly. Consequently, an alternative low-diffusivity dopant, carbon (C), was studied and a LET with a C-doped base was grown and fabricated. The highest light output was demonstrated for the C-doped LETs owing to the improved quality of the active layer.

36 MATERIALS SCIENCE↗

Achieving 1 nm capacitive effective thickness in atomic layer deposited HfO{sub 2} on In{sub 0.53}Ga{sub 0.47}As

A capacitive effective thickness (CET) value of 1.0 nm has been achieved in atomic layer deposited (ALD) high {kappa} dielectrics HfO{sub 2} on In{sub 0.53}Ga{sub 0.47}As/InP. The key is a short air exposure under 10 min between removal of the freshly grown semiconductor epilayers and loading to the ALD reactor. This has led to minimal formation of the interfacial layer thickness, as confirmed using x-ray photoelectron spectroscopy and high-resolution transmission electron microscopy. The measured electrical characteristics of metal-oxide-semiconductor diodes of Au/Ti/HfO{sub 2}(4.5 nm)/In{sub 0.53}Ga{sub 0.47}As showed a low leakage current density of 3.8x10{sup -4} A/cm{sup 2} at V{sub FB}+1 V, which is about eight orders of magnitudes lower than that of SiO{sub 2} with the same CET. The capacitance-voltage curves show an overall {kappa} value of 17-18, a nearly zero flatband shift, and an interfacial density of states D{sub it} of 2x10{sup 12} cm{sup -2} eV{sup -1}.

36 MATERIALS SCIENCE↗

Room temperature continuous wave operation of quantum cascade lasers with 12.5% wall plug efficiency

An InP based quantum cascade laser heterostructure emitting at 4.6 {mu}m was grown with gas-source molecular beam epitaxy. The wafer was processed into a conventional double-channel ridge waveguide geometry with ridge widths of 19.7 and 10.6 {mu}m without semi-insulating InP regrowth. An uncoated, narrow ridge device with a 4.8 mm cavity length was epilayer down bonded to a diamond submount and exhibits 2.5 W maximum output power with a wall plug efficiency of 12.5% at room temperature in continuous wave operation.

36 MATERIALS SCIENCE↗

Surface Fermi level in GaAsSb structures grown by molecular beam epitaxy on InP substrates

Photoreflectance (PR) spectroscopy is performed to investigate the Fermi level pinning at the surface of GaAsSb, in a series of epitaxial structures with different Sb concentration. PR spectra exhibit Franz-Keldysh oscillations, originating from the built-in electric field in the GaAsSb layer. Experimental results indicate that the surface Fermi level is pinned in the lower half bandgap. The surface Fermi level is determined versus the Sb concentration between 38% and 52%.

36 MATERIALS SCIENCE↗

Dissociation of H-related defect complex in InP using high energy light ions

High energy light ion irradiation has been used to anneal H-related defect complexes and to modify the electronic properties of semi-insulating InP (SI-InP). Raman and infrared spectroscopic measurements have been used to investigate the annihilation of native defects in SI-InP irradiated with 85 MeV C. Irradiation resulted in a decrease in sample resistivity by four orders of magnitudes and a change in the type of conductivity. The Raman spectroscopic results indicate an improvement in the InP sample due to irradiation up to an optimum fluence. The role of high electronic energy loss in defect annealing, which includes modification of the electrical properties and crystal structure of irradiated SI-InP, is discussed.

36 MATERIALS SCIENCE↗