Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ODS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Combined high-pressure neutron and X-ray diffraction study of H-D substitution effects on brucite

The high-pressure behavior of the mineral brucite, Mg(OH)2, is of great geochemical and geophysical interest, because brucite-type minerals serve as a simple analog for more complex, hydrogen-bearing oxide and silicate minerals in the deep-earth. A combined neutron and synchrotron x-ray powder diffraction study of hydrogenated and deuterated brucite was conducted at ambient temperature and at pressures to 9 and 20 GPa, using a Paris-Edinburgh (neutron diffraction) and a diamond anvil cell (synchrotron x-ray radiation), respectively. The two materials were synthesized by the same method and companion diffraction measurements of the two materials were conducted under the same conditions. Our experimental results show that the lattice-parameters of the a axis, parallel to the sheets of Mg-O octahedra, decrease only slightly with pressure with no effect of H-D substitution. However, the c axis of Mg (OD)2 is shorter and may exhibit greater compressibility with pressure than that of Mg (OH)2. Consequently, the unit-cell volume of deuterated brucite is slightly, but systematically smaller than that of hydrogenated brucite. Fitting to a third-order Birch-Murnaghan equation shows that values of the bulk modulus for hydrogenated and deuterated brucite are indistinguishable from each other within the experimental errors. The measured effect of H-D substitution on the unit-cell volume demonstrates that brucite (and other hydrous minerals) preferentially incorporate deuterium over hydrogen under pressure, suggesting that the distribution of hydrogen isotopes in deep-earth conditions may differ significantly from that in near-surface environments.

Brucite↗

Use of Polycarbonate Vacuum Vessels in High-Temperature Fusion-Plasma Research

Magnetic fusion energy (MFE) research requires ultrahigh-vacuum (UHV) conditions, primarily to reduce plasma contamination by impurities. For radiofrequency (RF)-heated plasmas, a great benefit may accrue from a non-conducting vacuum vessel, allowing external RF antennas which avoids the complications and cost of internal antennas and high-voltage high-current feedthroughs. In this paper we describe these and other criteria, e.g., safety, availability, design flexibility, structural integrity, access, outgassing, transparency, and fabrication techniques that led to the selection and use of 25.4-cm OD, 1.6-cm wall polycarbonate pipe as the main vacuum vessel for an MFE research device whose plasmas are expected to reach keV energies for durations exceeding 0.1 s

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Joining of 14YWT and F82H by Friction Stir Welding

The feasibility of using friction stir welding (FSW) to join specimens of the advanced oxide dispersion strengthened (ODS) 14YWT nanostructured ferritic alloy (NFA) and a plate of F82H tempered martensitic steel (TMS) was investigated. The sample used in the FSW experiment consisted of spot welding four specimens 14YWT prepared from prior tested dual notch fracture toughness bend bars in a corresponding slot that was machined in the F82H plate. The FSW run was successfully performed on the sample using a polycrystalline boron nitride tool (PCBN) that resulted in joints showing good bonding between butt joints of 14YWT specimens and 14YWT specimens and F82H plate. The joints were characterized by light microscopy and SEM analysis and were observed to be relatively narrow in width. The ultra-fine grain size associated with 14YWT increased by a factor of up to 3 while that of F82H was refined by a considerable amount in the thermomechanically affected zones (TMAZ) due to FSW. In addition, porosity was observed in the TMAZ of 14YWT on the advancing side of the FSW joint and at the interface between F82H and 14YWT. Vickers hardness (VH) measurements showed a decrease of ~120 VH from ~500 VH (~20% decrease) for 14YWT and an increase of ~220 VH from ~220 VH (~100% increase) for F82H in the FSW zones. Further refinements in the FSW process will be required to minimize defects including porosity.

Hoelzer, David T↗

Stability of nanoclusters in 14YWT oxide dispersion strengthened steel under heavy ion-irradiation by atom probe tomography

14YWT oxide dispersion strengthened (ODS) ferritic steel was irradiated with of 5 MeV Ni2+ ions, at 300 C, 450 C, and 600 C to a damage level of 100 dpa. The stability of Ti–Y–O nanoclusters was investigated by applying atom probe tomography (APT) in voltage mode, of the samples before and after irradiations. The average size and number density of the nanoclusters was determined using the maximum separation method. These techniques allowed for the imaging of nanoclusters to sizes well below the resolution limit of conventional transmission electron microscopy techniques. The most significant changes were observed for samples irradiated at 300 C where the size (average Guinier radius) and number density of nanoclusters were observed to decrease from 1.1 nm to 0.8 nm and 12 1023 to 3.6 1023, respectively. In this study, the nanoclusters are more stable at higher temperature.

99 GENERAL AND MISCELLANEOUS↗

Experimental study of forced convection heat transfer during upward and downward flow of helium at high pressure and high temperature

Fundamental high pressure/high temperature forced convection experiments have been conducted in support of the development of a Very High Temperature Reactor (VHTR) with a prismatic core. The experiments utilize a high temperature/high pressure gas flow test facility constructed for forced convection and natural circulation experiments. The test section has a single 16.8 mm ID flow channel in a 2.7 m long, 108 mm OD graphite column with four 2.3kW electric heater rods placed symmetrically around the flow channel. This experimental study presents the role of buoyancy forces in enhancing or reducing convection heat transfer for helium at high pressures up to 70 bar and high temperatures up to 873 degrees K. Wall temperatures have been compared among 10 cases covering the inlet Re numbers ranging from 500 to 3,000. Downward flows display higher and lower wall temperatures in the upstream and downstream regions, respectively, than the upward flow cases due to the influence of buoyancy forces. In the entrance region, convection heat transfer is reduced due to buoyancy leading to higher wall temperatures, while in the downstream region, buoyancyinduced mixing causes higher convection heat transfer and lower wall temperatures. However, their influences are reduced as the Reynolds number increases. This experimental study is of specific interest to VHTR design and validation of safety analysis codes.

Buoyancy↗

Electrode materials for rechargeable battery

A positive electrode is disclosed for a non-aqueous electrolyte lithium rechargeable cell or battery. The electrode comprises a lithium containing material of the formula NayLixNizMn1-z-z′Mz′Od, wherein M is a metal cation, x+y > 1, 0 < z < 0.5, 0 ≤ z′<0.5, y+x+1 is less than d, and the value of d depends on the proportions and average oxidation states of the metallic elements, Li, Na, Mn, Ni, and M, if present, such that the combined positive charge of the metallic elements is balanced by the number of oxygen anions, d. The inventive material preferably has a spinel or spinel-like component in its structure. The value of y preferably is less than about 0.2, and M comprises one or more metal cations selected preferably from one or more monovalent, divalent, trivalent or tetravalent cations, such as Mg2+, Co2+, Co3+, B3+, Ga3+, Fe2+, Fe3+, Al3+, and Ti4+. The electrode material can be synthesized using an ion-exchange reaction with a lithium salt in an organic-based solvent to partially replace sodium ions of a precursor material with lithium ions.

36 MATERIALS SCIENCE↗

APT Data Analysis towards Fission Products in TRISO Fuels

Tristructural isotropic (TRISO) particle is a promising candidate as fuel for high temperature gas reactors (HTGR) and other new generation fuel concepts like accident tolerant fuel for light water reactors. The TRISO coating is part of the HTGR functional containment and critical for the safety strategy for licensing purposes. The microstructure of TRISO particles typically consists of SiC and inner pyrolytic carbon (IPyC) layers, and has been an interesting topic, in particular, the behavior of fission products (FPs), such as Ag, Pd, etc. for many years. Historically, due to equipment and technique resolution limitations on radiological fuel materials, the distribution and behavior of FPs were not fully understood and resolved. Knowledge leapfrogged recently asAg-rich phase and Pd-rich precipitates were found along grain boundaries and inside SiC grains, respectively, by using scanning transmission electron microscopy (STEM) combined with energy dispersive x-ray spectrometry (EDS) and electron energy loss spectrometry (EELS) techniques [1]. However, as the Ag-rich phase and Pd-rich precipitate are much smaller than the STEM sample’s thickness, accurate quantitative analysis is difficult with TEM techniques. Furthermore, it is also extremely difficult to reveal the presence of other FPs in trace quantities. Atom probe tomography (APT) technique has been widely accepted and applied in the field of nuclear science, in particular for irradiated materials (e.g. ODS alloys), to reveal the distribution and composition of nano-sized features. However, there are very limited applications of APT towards studying FPs in fuels. Our preliminary results on neutron irradiated TRISO coated particles reveal a grain boundary containing multiple FPs [2]. This presentation will demonstrate though our study on the TRISO fuel sample how we identified the FPs in the SiC layer of the TRISO coated Particle, and challenged as FPs contains many unstable isotopes that are not shown in the CAMECA Periodic Table of the Isotopes for Atom Probe Tomography.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Frequency domain assurance criterion for defect detection in additively manufactured parts

Additive manufacturing (AM) is a very desirable manufacturing method for industries such as aerospace and automotive due to its ability to create internal features and complex geometries, however, these characteristics also present challenges for nondestructive evaluation (NDE) and defect detection. Dynamic analysis and modal analysis have shown promise for NDE and identifying flaws in AM parts. Frequency Domain Assurance Criterion (FDAC) is a method of dynamic evaluation that represents the degree of correlation between two sets of operational deflection shapes (ODS) at each spectral line. Using colormaps to display the results allows for quick and easy interpretation of parts’ similarities and differences. This method appears to show promise in identifying parts with minor defects and can be used to differentiate nominal and defective parts. This paper explores the use of FDAC on various AM parts with and without intentional defects.

Deonarain, G↗

Structural Materials for Innovative Nuclear Systems

This series of slides deal with: the goals for advanced fission reactor systems; the requirements for structural materials; a focus on two important types of materials: ODS and CMC; a focus on materials under irradiation (multiscale modelling, experimental simulation, 'smart' experiments in materials testing reactors); some concluding remarks.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Experimental study of heat transfer in a 7-element bundle cooled with supercritical Freon-12

Experimental data on Supercritical-Water (SCW) cooled bundles are very limited. Major problems with performing such experiments are technical difficulties in testing and experimental costs at high pressures, temperatures and heat fluxes. Also, there are only a few SCW experimental setups currently in the world capable of providing data. Supercritical Water-cooled nuclear Reactors (SCWRs), as one of the six concepts of Generation IV reactors, cannot be designed without such data. Therefore, a preliminary approach uses modeling fluids such as carbon dioxide and refrigerants instead of water is practical. In particularly, experiments in supercritical refrigerant-cooled bundles can be used. One of the SC modeling fluids typically used is Freon-12 (R-12) with the critical pressure of 4.136 MPa and the critical temperature of 111.97 deg. C. These conditions correspond to the critical pressure of 22.064 MPa and critical temperature of 373.95 deg. C in water. A set of experimental data obtained at the Inst. of Physics and Power Engineering (IPPE, Obninsk, Russia) in a vertically-oriented bundle cooled with supercritical R-12 was analyzed. This dataset consisted of 20 runs. The test section was 7-element bundle installed in a hexagonal flow channel with 3 grid spacers. Data was collected at pressures of approximately 4.65 MPa for several different combinations of wall and bulk-fluid temperatures that were below, at, or above the pseudo-critical temperature. The values of mass flux were ranged from 400 to 1320 kg/m{sup 2}s and inlet temperatures ranged from 72 to 120 deg. C. The test section consisted of fuel-element simulators that were 9.5 mm in OD with the total heated length of about 1 m. Bulk-fluid and wall temperature profiles were recorded using a combination of 8 different thermocouples. Analysis of the data has confirmed that there are three distinct heat-transfer regimes for forced convention in supercritical fluids: 1) Normal heat transfer; 2) Deteriorated heat transfer characterized with higher than expected wall temperatures; and 3) Enhanced heat transfer characterized with lower than expected wall temperatures. It was also confirmed that the effects of spacers are evident which was previously observed in sub-critical experimental data. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Skin Dosimetry in Breast Teletherapy on a Phantom Anthropomorphic and Anthropometric Phantom

This paper addresses the breast teletherapy dosimetry. The goal is to evaluate and compare absorbed doses in equivalent skin tissue, TE-skin, of an anthropomorphic and anthropometric breast phantom submitted to breast radiotherapy. The methodology involved the reproduction of a set of tomographic images of the phantom; the elaboration of conformational radiotherapy planning in the SOMAVISION and CadPlan (TPS) software; and the synthetic breast irradiation by parallel opposed fields in 3D conformal teletherapy at 6 MV linear accelerator Clinac-2100 C from VARIAN with prescribed dose (PD) of 180 cGy to the target volume (PTV), referent to the glandular tissue. Radiochromic films EBT2 were selected as dosimeters. Two independent calibration processes of films with solid water Gammex 457 plates and water filled box were produced. Curves of optical density (OD) versus absorbed dose were produced. Dosimeters were positioned in the external region of the breast phantom in contact with TE-skin, area of 4.0 cm{sup 2} each. The irradiation process was prepared in duplicate to check the reproducibility of the technique. The radiochromic films were scanned and their response in RGB (Red, Green, Blue) analyzed by the ImageJ software. The optical density was obtained and converted to dose based on the calibration curves. Thus, the spatial dose distribution in the skin was reproduced. The absorbed doses measured on the radiochromic films in TE-skin showed values between upper and lower quadrants at 9 o'clock in the range of 54% of PD, between the upper and lower quadrants 3 o'clock in the range of 72% and 6 o'clock at the lower quadrant in the range of 68 % of PD. The values are ±64% (p <0.05) according to the TPS. It is concluded that the depth dose measured in solid water plates or water box reproduce equivalent dose values for both calibration processes of the radiochromic films. It was observed that the skin received doses ranging from 50% to 78% of the prescribed dose after two parallel opposed irradiation fields. (authors)

61 RADIATION PROTECTION AND DOSIMETRY↗

Establishment of technical basis to implement accident tolerant fuels and component to existing LWRs

Fuel cladding, channel box, and control rod designed with new materials and concepts have been developed in Japan for increasing accident tolerance of Light Water Reactors (LWRs). Fundamental data have been mainly accumulated from the viewpoint of material technology. In order to create the technical basis for the practical use of the accident tolerant fuels (ATFs) and the other components in LWRs, a program sponsored and organized by the Ministry of Economy, Trade and Industry (METI) of Japan has been initiated. Main candidate materials of the ATFs and components in Japan are silicon carbide (SiC), stainless steel including oxide-dispersion strengthened (ODS) FeCrAl alloys, and tri-structural-isotropic (TRISO) fuel. First of all, current status of development of the candidates was investigated using information released from inside and outside Japan. Based on the results of the investigation, technology readiness of the candidates was evaluated and the attribute guide was created to clarify technical subjects for the practical use as the core components of the existing LWRs. For that purpose, a technology readiness table was reviewed in terms of fuel rod design, production and quality management, core and plant design, safety evaluation for design basis accident and severe accident, safety evaluation for transport and storage, establishment of treatment and disposal technologies, and development of standards and criteria, with 9 readiness levels. Considering the reviewed technology readiness table and the additionally evaluated influence of implementation of the new materials, a map of remaining subjects for research/development (Attribute guide) was prepared. Finally, a research plan was drafted for design and fabrication towards implementation of ATFs and components to the existing LWRs. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of surface modified Zr cladding by coating technology for ATF

It is expected that the accident tolerance fuels (ATF) will provide an enhanced fuel performance of active cooling in the reactor core for a longer time period during design-basis events as well as maintain or improve the fuel performance during normal operations and operational transients. Thus, various ATF cladding concepts have being suggested and developed in many countries. Among them, the coated cladding concept is studied in this work after the considerations of various performances in both the accidents and normal operation of LWRs. In the surface coated cladding concepts, the combination of coating material and coating method is a very important factor to determine the ATF cladding performance. As a new coating material, Cr-based alloy was developed to increase the corrosion resistance under normal operation as well as the oxidation resistance during an accident. From the high temperature oxidation test at 1200 Celsius degrees, the Cr-based alloy showed a superior oxidation resistance to Zircaloy-4 cladding, and showed more improved corrosion resistance than Zircaloy-4 cladding under 360 Celsius degrees PWR simulated loop conditions. The 3D laser coating and a combination of arc ion plating and laser beam scanning were developed to obtain a good adhesion property of corrosion resistance alloy coated on a Zr substrate. The corrosion resistance alloy (Cr-based alloy and FeCrAl alloy) coated layer used by two types of coating methods was maintained without peeling off during the ring compression test at room temperature, although some cracks were formed on the coated layer. After a high-temperature oxidation test at 1200 Celsius degrees for 2000 s, a very thin oxide layer, which was a few microns, was formed on the corrosion resistance alloy layer. However, the ZrO{sub 2} phase, which was thicker than 100 μm was formed on the Zr alloy cladding surface. Thus, it is known that the high-temperature oxidation resistance of commercial Zr alloy cladding can be considerably improved by the coating of corrosion resistant alloys. In addition, the partial oxide dispersion strengthened (ODS) treatment using a laser beam scanning (LBS) method was applied to decrease the ballooning and rupture opening during accident conditions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Adhesion Capabilities of Permanent Foaming Fixatives

DOE-EM have identified an operational requirement for a fixative that can immobilize and/or encapsulate residual contamination in 3D void volumes (pipes, gloveboxes, waste containers, etc.) during D and D activities. Failure to safely and effectively immobilize residual contamination can: Put workers at risk; Contaminate the public and environment; Drive up costs. Commercial-off-the-shelf (COTS) polyurethane (PU) foams is one possible solution and is currently being investigated by Savannah River National Lab (SRNL). Adhesion testing will dictate how well PU foams will adhere and immobilize residual contamination onto a substrate. Results can provide a performance criteria for Section 5 of ASTM E3191: Standard Specification for Permanent Foaming Fixatives Used to Mitigate Spread of Radioactive Contamination. Initial mechanical testing showed intumescent rigid PU foams were best in class (tensile, compression, TGA/DSC) Application of intumescent rigid PU foam in pipe scenario with 'contamination' showed excellent adhesion capabilities as long as foam had contact with pipe. The foam, however, was not able to penetrate 'contamination' but created pockets where the contamination interacted with the substrate. Pretreatment options of pipe were considered to produce better immobilization capabilities. Pretreatment options included COTS products like baking spray, rubber cement, and soap. Foam was still able to immobilize on a global sense, but not a local sense. Essentially acted as a mechanical plug. A tensile tester (MTS Criterion Series 43) was utilized to evaluate the tensile adhesion strength of 6 COTS PU foams. ASTM D1623: Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics. Procedures: PU foams were cured between two smooth 2'' x 2'' 304 stainless steel coupons with hinges glued on plates for gripping support. Parameters Used: Pull rate of 0.1 in/min. Calculations: Tensile adhesion strength, elongation, and ImageJ analysis of how PU foam is left on substrate. Outcome: The PU foam with the best adhesion capabilities would be downselected for further evaluation to be used as a permanent foaming fixative. The rigid PU foams had the best adhesion capabilities with the R1 foam having a max load of 236 N. One of the I-R2 samples reached almost 450 N and another sample reached 2500 N before slipping. The other intumescent foam, I-F4, had the most coverage on the stainless steel coupon's surface from the ImageJ results (61.43% surface coverage). The intumescent foam, I-R2, will be the foam of choice for future testing due its fire retardant and adhesion capabilities. Future directions: Conduct the following experiment in a pipe scenario with the down-selected PU foam. Procedures: PU foam will be cured between in a 304 stainless steel pipe (ID: 4'', OD: 4.5'', Height: 4''). Parameters Used: Compression testing results will be referenced to determine if foam's adhesion strength would be greater its compression strength as its being compressed. Calculations: Compression strength, shear stress, total time elapsed. Conduct further adhesion testing with the down-selected PU foam (I-R2) to be treated as a permanent foaming fixative (PFF). Determine the minimum contact the PFF should have with the substrate for adequate results. Evaluate if PFF's adhesion capabilities is time dependent (3.1.5 of ASTM E3911). Subject PFF to seismic stressors addressed in Safety Basis of Interim Operation documents (SBIO) to further evaluate adhesion capabilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Neutron and Ion Irradiation Studies on Advanced Steels Using the Nuclear Science User Facilities

For nuclear reactor structural materials, irradiation is capable of inducing a series of microstructural modifications, such as dislocation loops/network, selective elemental segregation and precipitation, voids and helium bubbles, leading to the degradation in structural materials' performance through irradiation hardening and embrittlement, swelling, irradiation creep, etc. Since radiation poses challenges for structural applications in nuclear reactors in multiple aspects and the underlying mechanisms are often interconnected, radiation effect studies need well-designed test matrix and proper characterization techniques. The Nuclear Science User Facilities (NSUF) offer extensive capabilities for studying radiation effects in nuclear fuels and structural materials. This research covers both neutron and ion irradiation studies carried out using a variety of instruments through the NSUF. The neutron irradiation ferritic ODS steel MA957 was accomplished utilizing the neutron irradiation capability of the Advanced Test Reactor (ATR) and the post-irradiation examination (PIE) capabilities of the Center for Advanced Energy Studies (CAES). The neutron-irradiated specimens were characterized using transmission electron microscopy (TEM) and atom probe tomography (APT). The in situ TEM ion irradiation study on austenitic stainless steel (SS) 316H was completed using the IVEM-Tandem facility at Argonne National Laboratory.

36 MATERIALS SCIENCE↗

Post Irradiation Examination of Fast Neutron Irradiated 14YWT Tubes at Nuclear Science User Facilities

Cladding materials for next generation nuclear reactors require resistance to high doses of fast neutron flux. Work through the Department of Energy's (DOE) Nuclear Technology Research and Development (NTR and D) Program's Advanced Fuel Campaign has identified 14YWT, a nano-ferritic oxide dispersion strengthened alloy as a promising alloy and has made a 50 kg batch of material, FCRD-NFA1, with nominal composition Fe-14Cr-3W0.4Ti-0.2Y in weight percentage. Plates were extruded from milled powder at Oak Ridge National Laboratory and then electro-discharge machined (EDM) into two sizes of tubes at Los Alamos National Laboratory (LANL). The OD of the tubes were polished to remove the EDM recast layer. Twenty-four of these tubes were placed into the BOR60 reactor, a sodium fast reactor, at the RIAR lab in Dimitrovgrad Russia. Irradiation conditions depended on exact location within the reactor, but the two samples in this study (L108 and L202) were irradiated to 7 dpa at 360-370 deg. C (Sample L108), and 6 dpa at 385-430 deg. C (L202). More detailed temperature models are pending for sample L202. Post irradiation examination took place at both LANL and the University of California, Berkeley (UCB). Facilities used at LANL (CMR Wing 9 Hot Cells, Electron Microscopy Lab (EML)) are part of a pending NSUF partner facility application, while the work at UCB was completed under a Nuclear Science User Facility, Rapid Turnaround Experiment Proposal (NSUF-RTE)

36 MATERIALS SCIENCE↗

Development of a second COMB dipole magnet with STAR wires

Rare-Earth Barium Copper Oxide (REBCO) coated conductors are an attractive option for application in high-field accelerator magnets due to their high critical field and the convenience of fabrication without heat treatment compared to some other superconductors. Fermilab plays a vital role in superconducting accelerator magnet R&D under the framework of the U.S. Magnet Development Program. An integral part of that program is the accelerator magnet development based on REBCO conductors to demonstrate self-fields of 5 T or greater compatible with operation in hybrid configurations to generate fields beyond 16 T for future High Energy Physics (HEP) applications. A small, two-layer REBCO dipole magnet based on the Conductor on Molded Barrel (COMB) magnet technology, developed at Fermilab with Symmetric Tape Round (STAR®) wires from AMPeers LLC was recently fabricated and tested in liquid helium, demonstrating the design feasibility. A second dipole magnet based on the same technology is currently under development at Fermilab. The coil has a 60-mm clear bore and a 120-mm OD and consists of six layers of STAR® conductor, which allows to significantly increase the magnetic field compared to the previous design, and potentially probe the 5 T self-field target. This presentation reports the progress in the magnet development.

Kashikhin, Vadim [Fermilab]↗

Development and Validation of MALAMUTE model for Electric Field Assisted Sintering of Structural Materials

Fusion power plant designs feature extreme material performance requirements for structural material candidates. In addition to conventional alloys, more advanced composites and oxide dispersion strengthened (ODS) alloys are being explored, however, achieving the desired microstructures to maximize performance using traditional manufacturing methods can be challenging. The advanced manufacturing (AM) electric field-assisted sintering (EFAS) technique offers improved control over the final microstructure through higher heating and cooling rates and moderate pressures. Modeling and simulation tools show promise in elucidating the process-structure-property-performance (PSPP) correlation for AM-produced parts, including the EFAS process. An inherently multiscale process, the EFAS technique aligns well with the multiscale modeling capability of the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE)[cite]. We present here an electro-thermo-mechanical approach to modeling the EFAS process using the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) code. Prediction of the field and gradient distributions across the EFAS tooling is required to accurately describe the conditions for the lower-scale microstructural evolution models. In this work we present the MALAMUTE model developed to predict the electrical potential, temperature, and mechanical stress distribution across the EFAS graphite tooling and part at the larger engineering-scale. Validation of the MALAMUTE engineering-scale model is completed using data from experimental densification and pre-densified runs of iron powder via EFAS at 1000oC. These runs were conducted using a Thermal Technology DCS-5 EFAS system. Data collected during the experiment runs include the direct current (DC) supplied to the graphite tooling, the temperature of the graphite tooling as measured with a pyrometer, and the force applied to the top of the graphite tooling stack, and the data were recorded every 10 seconds. Our validation approach used the current and force data from the EFAS run as boundary condition inputs to the MAMALUTE simulation; the temperature data were used to evaluate the MALAMUTE EFAS model prediction. Results of the MALAMUTE simulations are employed to connect the external pyrometer temperature measurement to the temperature profile across the part undergoing consolidation. We investigate the impact of material property variation and mesh deformation on the temperature profile as predicted by MALAMUTE. We conclude by highlighting projects where the MALAMUTE EFAS modeling and simulation capabilities will be used to assist experimental design.

36 - MATERIALS SCIENCE↗