Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Milling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High-coercivity ThMn 12 -type monocrystalline Sm–Zr–Fe–Co–Ti particles by high-temperature reduction diffusion

The ThMn 12 -type (Sm,Zr)1(Fe,Co,Ti) 12 compounds have the potential of powerful permanent magnets. Magnetically hard and anisotropic powders of such compound have been prepared by subjecting elemental oxides and Co mixed with Ca and CaO dispersant to a succession of high-energy ball-milling, reduction diffusion at 990–1220 °C and repeated washing. The size of the resulting ThMn 12 -type crystallites, their coercivity and fraction of monocrystalline particles were all found to increase with the reduction-diffusion temperature. Particles synthesized at 1220 °C were highly monocrystalline with a mean size of 0.54 μm and, after a magnetic-field alignment, exhibited a coercivity of 1.26 T and a full-density-projected maximum energy product of at least 209 kJ/m 3 (26.3 MGOe). Here, the strong positive effect of the reduction-diffusion temperature on the coercivity has been attributed to separation of the crystallites and to decrease in the incidence of structural defects.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Lead leaching and electrowinning in acetic acid for solar module recycling

It is imperative to recover lead (Pb) contained in end-of-life solar modules. In this paper, a two-step leaching and electrowinning process using acetic acid is investigated for Pb recovery. Acetic acid with hydrogen peroxide can dissolve Pb quickly and, under some conditions, in a matter of minutes. Pb electrowinning has been successfully demonstrated from aqueous solutions of 0.009 M lead(II) acetate with 0–10% v/v acetic acid. Pb-containing deposits are found on both the copper cathode and graphite anode. X-ray diffraction, energy-dispersive X-ray spectroscopy, and Fourier transform infrared spectroscopy confirm the presence of metallic Pb and Pb(II) oxide (PbO) co-deposits on the cathode. Further, there is also the formation of lead subacetate on the cathode under certain conditions. On the anode, the deposit consists of lead(IV) oxide and superoxide (PbO 2 and Pb 1–x O 2 ). A Pb recovery rate of 99% is achieved in 0.009 M lead(II) acetate solutions with 10% v/v acetic acid by applying a reduction potential of either –0.8 V or –1.0 V versus the silver/silver chloride reference electrode for 24h. Pb leaching with acetic acid is also demonstrated from milled silicon solar modules.

14 SOLAR ENERGY↗
DOE OSTI2023

Nanometer-scale electrical potential imaging on absorber of CdSeTe solar cells

Here, we report on nm-scale electrical potential imaging throughout As-doped and Cu-doped CdSeTe absorbers using Kelvin probe force microscopy (KPFM). The potential imaging was conducted both laterally and vertically on beveled films using ion milling at small glancing angle. KPFM images electrical potential on the beveled surface and assesses defect charging in the subsurface region within a screening length from the beveled surface. We found that the grain boundaries were positively charged and that there were significant potential fluctuations in both grain boundary versus grain interior and intragrain. We further found that these potential fluctuations decreased significantly toward the front interface. Time of flight secondary ion mass spectrometry imaging shows that Se content increased toward the front interface, consistent with Se passivation of defects. The potential fluctuation was induced by defect charging, and the results elucidate different details of the defect configurations and grain structures of the films with different CdCl 2 treatment temperatures in the As-doped CdSeTe. The defect configurations in the region near the front interface can be a main factor contributing to the device performance difference. Our potential imaging provides insights about the defects throughout the absorber films, and shows that the potential fluctuation has a direct correlation to the V oc deficit.

14 SOLAR ENERGY↗
DOE OSTI2025

Optimized NiTe 2 /Ni back contacts via chemical deposition for high performance CdTe solar cells

The development of efficient and stable back contacts remains a major challenge in achieving high performance and long-term stability of CdTe thin-film solar cells. Here, this work revisits the formation of NiTe 2 by chemical bath deposition (CBD) as a back contact for CdTe devices. An optimized CBD recipe, based on high-purity precursors and the addition of copper chloride directly into the bath, was developed and applied to fabricate Cu-doped CdTe solar cells. A modified Cu-free methodology was also applied to Group V doped absorbers. The process included pinhole filling, ion milling, CBD, annealing, and sputtering to form a low-barrier back contact. Devices fabricated using this method achieved consistent open-circuit voltages (V oc ) above 800 mV and fill factors (FF) exceeding 70%. The best Cu-doped devices reached power conversion efficiencies (PCE) above 18 %, and preliminary results with Group V-doped material demonstrated compatibility of the method with high-efficiency, state-of-the-art CdTe devices. This study shows that NiTe 2 /Ni back contacts, formed via an optimized chemical process followed by sputtering of Ni, represent a promising pathway for achieving low-barrier and potentially stable back contacts in modern CdTe photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2020

Samarium isotope compositions of uranium ore concentrates: A novel nuclear forensic signature

Uranium ore is mined and milled to produce uranium ore concentrate (UOC), a regulated product of the nuclear fuel cycle. Additionally, diversion of UOC from the fuel cycle into possible weapons production is a key concern in global nonproliferation efforts. As such, the ability to trace the origin of seized nuclear materials is imperative to law enforcement efforts. Although isotopic signatures of UOCs have proven fruitful to pinpoint sample provenance, new isotopic signatures are needed because most existing isotopic signatures are not indicative of the original ore body from which the U is derived. In this work, we developed a new method to separate samarium (Sm) from a U-rich sample matrix and report the first Sm isotope compositions of 32 UOCs derived from a variety of worldwide uranium mines. Relative to terrestrial standards, approximately half the UOCs have resolved and anticorrelated 149 Sm- 150 Sm isotope compositions, consistent with the capture of thermal neutrons by 149 Sm in the ore body. The UOCs with anomalous Sm isotope compositions tend to derive from older (~>1.5Ga) and higher-grade ore bodies, although other factors, such as the presence of neutron moderators like water, also play a role. Nonetheless, the Sm isotope compositions of UOCs directly reflects the neutron fluence over the history of the original ore body and can be used to discern different geologic conditions associated with that ore body. Overall, this work demonstrates the potential use of Sm isotopes as a novel nuclear forensics signature for origin assessment of UOCs.

58 GEOSCIENCES↗
DOE OSTI2025

Comparison of three measurement modalities for 3D characterization of manufactured features and process-induced porosity in titanium alloy additively manufactured parts

Nondestructive characterization of internal features and defects within complex components is vital for many industrial applications, particularly with the advent of additive manufacturing (AM) technologies. However, community understanding of the limitations of nondestructive methods such as X-ray Computed Tomography (CT) can be limited in certain industrial sectors as these may be emergent applications. In this paper, we investigate the limits of X-ray CT measurements and compare extracted data with mechanical polishing serial sectioning (MPSS) and confocal laser scanning microscopy (CLSM). The test object is an additively manufactured titanium alloy disk that contains both process-induced porosity and machined features, including focused ion beam milled features designed to probe the resolution limits of X-ray CT. Results show that each of these characterization techniques has advantages and disadvantages. We compare data acquisition times, spatial resolution, geometric measurement accuracy and defect visualization fidelity across these modalities to establish a practical framework.

Additive manufacturing↗
DOE OSTI2020

Variable voltage electron microscopy: Toward atom-by-atom fabrication in 2D materials

The precisely focused electron beam (e-beam) in scanning transmission electron microscopy has been found to be a versatile tool for patterning matter on the atomic level and enabling atom-by-atom fabrication, however, beam-induced phenomena are known to be extremely sensitive to the e-beam energy and are closely correlated with the proximity of the knock-on threshold. Here we provide a method to control the energy transferred to the sample while facilitating much faster changes in accelerating voltages by maintaining a nearly constant temperature in the electron microscope lenses. We use this method to demonstrate in-situ nano-milling of a graphene film followed rapidly by “gentler” imaging at lower energy. Additionally, the insertion and controlled movement of silicon dopants in graphene is demonstrated by employing a different e-beam energy during each process. We believe the incorporation of variable e-beam energy will broaden the potential for atomic scale e-beam fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Wet-chemical etching of FIB lift-out TEM lamellae for damage-free analysis of 3-D nanostructures

Reducing ion beam damage from the focused ion beam (FIB) during fabrication of cross sections is a well-known challenge for materials characterization, especially cross sectional characterization of nanostructures. To address this, a new method has been developed for cross section fabrication enabling high resolution transmission electron microscopy (TEM) analysis of 3-D nanostructures free of surrounding material and free of damage detectable by TEM analysis. Before FIB processing, nanopillars are encapsulated in a sacrificial oxide which acts as a protective layer during FIB milling. Furthermore, the cross sectional TEM lamella containing the nanopillars is then mounted and thinned with some modifications to conventional FIB sample preparation that provide stability for the lamella during the following wet-chemical dip etch. The wet-chemical etch of the TEM lamella removes the sacrificial oxide layer, freeing the nanopillars from any material that would obscure TEM imaging. Both high resolution TEM and aberration corrected scanning TEM images of Si/SiGe pillars with diameters down to 30 nm demonstrate the successful application of this approach.

3-d nanostructure analysis↗
DOE OSTI2020

Aggregated nanoparticles: Sample preparation and analysis by atom probe tomography

Atom probe tomography (APT) allows measurement of the three-dimensional structure and composition of materials, but specific sample preparation procedures are required for challenging materials such as aggregates of nanoparticles. Indeed, the presence of porosity within the specimen affects both the stability of the sample and the accuracy of the data. In this work, aggregates of nanoparticles were transferred onto a micromanipulator tip and embedded via electron-beam-assisted deposition of Pt. Successive FIB-millings and Pt-depositions are needed to create suitable APT tips. The 3D reconstruction reveals the presence of 15–20 nm nanoparticles, and massspectral analysis shows the absence of trace elements within the catalyst, thus serving as quality control for the synthesis of nanoparticles with specific compositions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Evaluation of automated stability testing in machining through closed-loop control and Bayesian machine learning

Here, this paper describes a system for automated identification of the optimal stable cutting parameters in milling through Bayesian machine learning and closed-loop control. The closed-loop control system consists of a process monitoring architecture, an analysis framework, and a feedback mechanism. The analysis framework consists of a Bayesian machine learning algorithm that learns a stability map given test results. The learned stability map is used to select parameters for stability testing using an expected improvement in the material removal rate criterion. The test parameters are communicated to the machine controller to complete the test cut through a feedback mechanism. The test cuts were monitored using an audio signal; the stability of the test cut was determined by analyzing the frequency content of the audio signal. The test result was fed back to the Bayesian learning algorithm to complete the loop. Experimental results demonstrate that the system can identify the optimal stable parameters without information about the cutting force model or the structural dynamics. The system provides a low-cost method for optimal stable parameter identification in an industrial environment.

Chatter↗
DOE OSTI2021

EBSD of Rough Native CuInGaSe2 Thin-Films

The polycrystalline Cu (In, Ga) Se2, or CIGS, based thin-film materials system has long been studied for use in photovoltaic technologies, where its bandgap tunability, mechanical flexibility, and relatively low production costs are all appealing. Nonetheless, significant defect populations, which serve to reduce efficiency, create performance instabilities, and increase concerns about long-term reliability, have hindered wide-scale adoption. Prior work, including application of a scanning probe based deep level trap spectroscopy (SP-DLTS) defect mapping technique and scanning transmission electron microscope (STEM) based electron energy loss spectroscopy (EELS), has shown that the most detrimental defects, with energy level near mid-gap (thus serving as a carrier recombination center), are most likely caused by CuIn/Ga antisites and tend to cluster at or around certain grain boundaries [1,2]. However, the exact nature of these particular boundaries — their structures, chemistries, or even the relative misorientation of their associated grains — and their relation to this defect clustering and/or its formation is yet unknown. As such, electron backscatter diffraction (EBSD) orientation mapping, directly correlated with defect-sensitive techniques like SP-DLTS and/or STEM-EELS, could prove critical for providing the final missing links toward understanding the mechanisms behind these defects. Indeed, recent studies using correlative electron beam induced current (EBIC) with EBSD have been able to identify boundaries, and their relative misorientations, that possess detrimental electronic properties [3]. However, because EBIC is unable to resolve the defect energy levels, many questions are left unanswered. Furthermore, this study, and others like it, employed focused ion beam (FIB) milling to flatten the natively-rough CIGS [3-5], which may run the risk of changing the nature of any near-surface defect structures.

14 SOLAR ENERGY↗
DOE OSTI2022

Using Xe Plasma FIB for High-Quality TEM Sample Preparation

Here, a direct comparison between electron transparent transmission electron microscope (TEM) samples prepared with gallium (Ga) and xenon (Xe) focused ion beams (FIBs) is performed to determine if equivalent quality samples can be prepared with both ion species. We prepared samples using Ga FIB and Xe plasma focused ion beam (PFIB) while altering a variety of different deposition and milling parameters. The samples’ final thicknesses were evaluated using STEM-EELS $\textit{t/λ}$ data. Using the Ga FIB sample as a standard, we compared the Xe PFIB samples to the standard and to each other. We show that although the Xe PFIB sample preparation technique is quite different from the Ga FIB technique, it is possible to produce high-quality, large area TEM samples with Xe PFIB. We also describe best practices for a Xe PFIB TEM sample preparation workflow to enable consistent success for any thoughtful FIB operator. For Xe PFIB, we show that a decision must be made between the ultimate sample thickness and the size of the electron transparent region.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Focused Ion Beam Preparation of Low Melting Point Metals: Lessons Learned From Indium

Indium (In) and other low melting point metals are used as interconnects in a variety of hybridized circuits and a full understanding of the metallurgy of these interconnects is important to the reliability and performance of the devices. Here, this paper shows that room temperature focused ion beam (FIB) preparation of cross-sections, using Ga + or Xe + can result in artifacts that obscure the true In microbump structure. The use of modified milling strategies to minimize the increased local sample temperature are shown to produce cross-sections that are representative of the In bump microstructure in some sample configurations. Furthermore, cooling of the sample to cryogenic temperatures is shown to reliably eliminate artifacts in FIB prepared cross-sections of In bumps allowing the true bump microstructure to be observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mild Acetylation and Solubilization of Ground Whole Plant Cell Walls in EmimAc: A Method for Solution-State NMR in DMSO-d6

Lignocellulosic biomass is mainly composed of polysaccharides and lignin. The complexity and diversity of the plant cell wall polymers makes it difficult to isolate the components in pure form for characterization. Many current approaches to analyzing lignocellulose structure, which involve sequential extraction and characterization of the resulting fractions, are time-consuming and labor-intensive. The present study describes a new and facile system for rationally derivatizing and dissolving coarsely ground plant cell wall materials. Using ionic liquids (EmimAc) and dichloroacetyl chloride as a solvent/reagent produced mildly acetylated whole cell walls without significant degradation. The acetylated products were soluble in DMSO-d6 from which they can be characterized by solution-state two-dimensional nuclear magnetic resonance (2D NMR) spectrometry. A distinct advantage of the procedure is that it realizes the dissolution of whole lignocellulosic materials without requiring harsh ball-milling, thereby allowing the acquisition of high-resolution 2D NMR spectra to revealing structural details of the main components (lignin and polysaccharides). The method is therefore beneficial to understanding the composition and structure of biomass aimed at its improved utilization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Observations of Nocturnal Sulfuric Acid Formation in Pittsburgh, PA

Measurements of sulfuric acid (H 2 SO 4 ) and sulfur trioxide (SO 3 ) were conducted in Pittsburgh, Pennsylvania, during field campaigns in Fall 2023 and Fall 2024. These measurements identified nocturnal concentrations of H 2 SO 4 comparable to those of daytime values. Nocturnal H 2 SO 4 concentrations were observed to increase by 5 × 10 5 to 5 × 10 7 molecules cm –3 above background on 16 of the 31 measurement nights. The median peak concentration during events was 6.5 × 10 6 molecules cm –3 , with a maximum of 1.0 × 10 8 molecules cm –3 , exceeding previously reported nighttime concentrations. Increases in H 2 SO 4 concentrations were positively correlated with the anomalously high SO 3 concentrations and condensation sink rates, indicating that the formation of H 2 SO 4 increased to overcome the loss rates to particles. Increases in particulate mass and the mass fraction of metals commonly emitted from coal combustion and steel production were also observed. The air masses were traced back to the southeast of Pittsburgh, a region home to a steel mill, coke plant, and a steel processing plant. The observations indicate a previously unrecognized nighttime formation pathway for H 2 SO 4 , potentially from heterogeneous catalysis with metal or black carbon, originating from steel and coke plant emissions. Further measurements are needed to identify key compounds and chemical processes driving these increases in nocturnal H 2 SO 4 concentrations.

aerosols↗
DOE OSTI2020

Technoeconomic Analysis of the Electrochemically Mediated Amine Regeneration CO 2 Capture Process

The electrochemically mediated amine regeneration (EMAR) process presents an alternative route to the conventional thermal amine regeneration for carbon capture from a flue gas source. In this study, we conducted an economic analysis on the EMAR system for postcombustion CO2 capture from a 550 MWe power plant capturing 3.1 MtCO2 annually and from a mini steel mill with annual capture close to 170 ktCO2. We followed the recommendation of the National Energy Technology Laboratory (NETL) 2010 report to estimate the cost of CO2 avoided ([$/tCO2]). Detailed cost modeling of the electrochemical separation stage was conducted. This is integrated with the entire process flowsheet (e.g., including absorber, compressor, pumps, and other auxiliary equipment). Here, we identified the membrane cost as the dominant capital cost for the electrochemical separation train. At a membrane unit price of less than 10/m2, the CO2 capture cost can be reduced to below 50/tCO2 with optimized process conditions (e.g., desorption pressure and utilization of waste heat). Improvements in process design, cell construction, and solvent formulation may lead to additional reductions in the CO2 capture cost.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Transport of Compressed Woody Biomass: Correlating Rheology and Microcompounder Measurements

Transport of milled solid biomass can be problematic in biomass conversion processes due to the material’s high cohesiveness, low bulk density, and poor flowability. Here, the goal is to investigate the flow behavior of compressed biomass under conditions similar to compression-screw feeders. To mimic the flow of woody biomass inside a compression-screw feeder, two lignocellulosic biomass feedstocks were fed to a co-rotating twin-screw microcompounder. Force and screw speed from the microcompounder were correlated to viscosity in a traditional rheometer, where low-density polyethylene served as a control. The deformation of compressed biomass in a lab-scale compounder is strongly dependent on screw speed and moisture content. Shear stress in woody biomass decreased with the shear rate, indicating negative plastic viscosity. Moreover, viscosity decreased one order of magnitude as screw speed increased from 10 to 90 rpm. Increasing moisture from 10 to 50% reduced the viscosity of the compressed biomass by 60%.

09 BIOMASS FUELS↗
DOE OSTI2021

Graphitized Biocarbon Derived from Hydrothermally Liquefied Low-Ash Corn Stover

Graphitized biocarbon can be utilized for energy storage applications such as supercapacitors. The scientific community have geared their attention to obtain such value-added product from abundantly available and low-cost biomass feedstock agricultural residues such as corn stover. Lignocellulosic components embedded within the cell wall of biomass substrates can provide a fine template for enhanced ion storage, transport, and rate capabilities, desirable for electrochemical storage. Presented is the utilization of homogenized low ash content corn stover milled and sieved to desired specifications, which underwent hydrothermal liquefaction in the presence of Ni-based catalytic salts at 275 o C. The hydrochar obtained by solid residue extracted from the reaction slurry was washed to acid neutral and subjected to catalytic activation using ZnCl 2 , followed by thermal annealing at 400 o C for morphological and pore size enhancement of the resulting biochar. Carbonization was performed on acid neutralized hydrochar at 850 °C to further enhance pore structures and increase graphitization for improved conductivity. Catalytic materials exhibited a specific capacitance of 316 F g -1 and held a 100% retention beyond 10,000 cycles. BET, Raman, XRD, cyclic voltammetry, chronopotentiometry, and EIS are discussed herein.

Biomass↗