Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Effect of freeze-drying and self-ignition process on the microstructural and electrochemical properties of Li{sub 4}Ti{sub 5}O{sub 12}

Graphical abstract: - Highlights: • Li{sub 4}Ti{sub 5}O{sub 12} is prepared by a method involving self-ignition of a freeze-dried gel. • Addition of NH{sub 4}NO{sub 3} modifies the self-ignition propagation mode. • Well-crystallized Li{sub 4}Ti{sub 5}O{sub 12} phase is obtained after only 2 h at 800 °C. • Li{sub 4}Ti{sub 5}O{sub 12} powder has 161 mAh g{sup −1} capacity and good retention at C/4 rate. - Abstract: Crystalline Li{sub 4}Ti{sub 5}O{sub 12} is synthesized by a method involving the freeze-drying and self-ignition of a gel prepared from titanium isopropoxide, lithium nitrate and hydroxypropylmethylcellulose (HPMC). This synthesis route yields crystalline Li{sub 4}Ti{sub 5}O{sub 12} particles after calcination at 800 °C for 2 h. In an alternative route, addition of ammonium nitrate shifts the self-ignition mode from wave-like propagation to simultaneous. Powders with different microstructures are thereby obtained. Electrochemical characterization shows that the best results for Li{sup +} intercalation/desintercalation are obtained for the powder prepared without ammonium nitrate addition. These results highlight the necessity for a control of the self-ignition mode to obtain adequate properties.

36 MATERIALS SCIENCE↗

Microstructure and thermal properties of copper–diamond composites with tungsten carbide coating on diamond particles

An effective method for preparing tungsten carbide coating on diamond surfaces was proposed to improve the interface bonding between diamond and copper. The WC coating was formed on the diamond surfaces with a reaction medium of WO{sub 3} in mixed molten NaCl–KCl salts and the copper–diamond composites were obtained by vacuum pressure infiltration of WC-coated diamond particles with pure copper. The microstructure of interface bonding between diamond and copper was discussed. Thermal conductivity and thermal expansion behavior of the obtained copper–diamond composites were investigated. Results indicated that the thermal conductivity of as-fabricated composite reached 658 W m{sup −} {sup 1} K{sup −} {sup 1}. Significant reduction in coefficient of thermal expansion of the composite compared with that of pure copper was obtained. - Highlights: • WC coating was successfully synthesized on diamond particles in molten salts. • WC coating obviously promoted the wettability of diamond and copper matrix. • WC coating greatly enhanced the thermal conductivity of Cu–diamond composite. • The composites are suitable candidates for heat sink applications.

36 MATERIALS SCIENCE↗

Tunning of microstructure and thermoelectric properties of Ca{sub 3}Co{sub 4}O{sub 9} ceramics by high-magnetic-field sintering

The structural, magnetic, electrical, and thermal transport properties of Ca{sub 3}Co{sub 4}O{sub 9} ceramics sintered under high magnetic field were investigated. Crystal grain texturing and densification were achieved through cold-pressing and high-magnetic-field sintering techniques. The c-axis of the layered crystal grain was partly oriented along the c-axis of the pressed samples via a cold-pressing technique, and the degree of orientation was further increased while applying the magnetic field in the sample sintering progress. The easy magnetization axis of Ca{sub 3}Co{sub 4}O{sub 9} polycrystalline ceramics was found to be the c-axis. The room-temperature resistivity along the ab-plane of the sample sintered under 8 T magnetic field was about 30% smaller than that of the sample sintered without magnetic field, and the Seebeck coefficient of the former reached 177.7 {mu}V/K at the room temperature, which is about 50% larger than that of the latter. Consequently, for the sample sintered at 8 T magnetic field, the power factor along the ab-plane was enhanced by about 1.8 times compared to the sample without magnetic field sintering. The obtained result is suggested to originate from the variations of the carrier mobility and spin-orbital degeneracy due to high-magnetic-field sintering in the progress of the sample preparation.

36 MATERIALS SCIENCE↗

Effect of sputtering pressure on microstructure and bolometric properties of Nb:TiO{sub 2−x} films for infrared image sensor applications

This study aims to investigate the influence of the sputtering pressure (P{sub S}) on Nb:TiO{sub 2−x} films to enhance the bolometric properties. A decrease in the growth rate with the sputtering pressure was perceived in amorphous Nb:TiO{sub 2−x} films. The incorporation of oxygen with P{sub S} was confirmed in an X-ray photo electron spectroscopy analysis. The electrical resistivity was increased with an increase in P{sub S} due to a decrease in the number of oxygen vacancies. The linear I-V characteristics confirmed the ohmic contact behavior between the Nb:TiO{sub 2−x} layer and the electrode material. The present investigation finds that the sample with lower resistivity has good bolometric properties with low noise and high universal bolometric parameters. Finally, the Nb:TiO{sub 2−x} sample deposited at a sputtering pressure of 2 mTorr shows better bolometric properties than other materials for infrared image sensor applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructure and Mechanical Properties of Ni-based Alloys Fabricated by Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies (AMMT) program is aiming at the accelerated incorporation of new materials and manufacturing technologies into nuclear-related systems. Complex Ni-based components fabricated by laser powder bed fusion (LPBF) could enable operating temperatures at T > 700°C in aggressive environments such as molten salts or liquid metals. However, available mechanical properties data relevant to material qualification remains limited, in particular for Ni-based alloys routinely fabricated by LPBF such as IN718 (Ni- 19Cr-18Fe-5Nb-3Mo) and Haynes 282 (Ni-20Cr-10Co-8.5Mo-2.1Ti-1.5Al). Creep testing was conducted on LPBF 718 at 600°C and 650°C and on LPBF 282 at 750°C. finding that the creep strength of the two alloys was close to that of wrought counterparts. with lower ductility at rupture. Heat treatments were tailored to the LPBF-specific microstructure to achieve grain recrystallization and form strengthening γ' precipitates for LPBF 282 and γ' and γ" precipitates for LPBF 718. In-situ data generated during printing and ex-situ X-ray computed tomography (XCT) scans were used to correlate the creep properties of LPBF 282 to the material flaw distribution. In- situ data revealed that spatter particles are the potential causes for flaws formation in LPBF 282. with significant variation between rods based on their location on the build plate. XCT scans revealed the formation of a larger number of creep flaws after testing in the specimens with a higher initial flaw density. which led to a lower ductility for the specimen.

Dryepondt, Sebastien↗

Transient Microstructure Evolutions and Local Properties of Dual-Phase 980 MPa Grade Steel Via Friction Stir Spot Processing

Friction stir processing is a novel solid-state process to modify microstructures and their properties by intense, localized plastic deformation. However, little research has been reported for microstructure evolutions of advanced high-strength steels during the process. The present work focuses on the study of transient microstructure changes and local mechanical properties for friction stir spot processed dual-phase (DP) 980 MPa grade steel (DP980) under different peak temperatures. A pinless silicon nitride ceramic tool was used to produce relatively simple material deformation and flow near the tool. Friction stir spot processed steel samples were characterized by optical and electron microscopies. Furthermore, Vickers microhardness and nano-indentation measurements were used to study local mechanical properties for correlation with microstructures. A swallow layer of refined grains (<0.6 µm) was obtained with a low peak temperature (under 400 °C), whereas higher peak temperatures (>Ac 1 ) led to a change in grain size with different microstructures (fine-grained DP or martensite). Electron back-scattered diffraction characterizations revealed a large deformation in the as-received microstructures (mixture of ferrite and tempered martensite) induced by friction stir spot processing, leading to recrystallization and grain refinement around the stirred zone. Also, nano-indentation measurements showed a higher hardness than the hardness of the as-received DP980. Friction stir processing with different process conditions effectively changed microstructures and local mechanical properties.

36 MATERIALS SCIENCE↗

Microstructure evolution and properties of graphene nanoplatelets reinforced aluminum matrix composites

Highlights: • Lamellar structure of GNPs fibers and Al matrix was obtained in the rolling direction. • Stacking faults were observed in Al grains due to greatly increased GNPs/Al interfaces. • Strength of Al-0.2 wt% GNPs increased 36.8% with negligible electrical conductivity loss. - Abstract: Aluminum matrix composites reinforced with graphene nanoplatelets (GNPs) were prepared by continuous casting and subsequent rolling. Al-GNPs master alloy, prepared by ball milling and cold pressing, was added into Al melts to fabricate the composites. Microstructure evolution of the composites were observed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron back scattered diffraction (EBSD). GNPs distributed uniformly in the as-cast specimen and then transformed into fibers in the rolling direction after deformation and finally a lamellar structure formed in the composites. Raman spectra showed that the structural damage of GNPs mainly came from ball milling. The interface between GNPs and Al was well combined in general while a few microcracks were observed, which reduced the ductility of the composites and no adverse aluminum carbide (Al{sub 4}C{sub 3}) was detected at the interface. Stacking faults were observed interior of the aluminum grain, which may due to the existence of plentiful interface introduced by GNPs. Fracture observation revealed that the load transferred from Al matrix to GNPs. The ultimate tensile strength of Al-0.2 wt% GNPs composites was about 36.8% higher than that of pure Al with the same casting and rolling process, which should result from the lamellar structure and load transfer, while the conductivity of the composites decreased slightly, indicating that interface scattering between Al and GNPs is very limited. The investigation results show that Al-GNPs composite is potential for high strength and high conductivity application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure and thermomechanical properties relationship of segmented thermoplastic polyurethane (TPU)

Thermoplastic polyurethanes (TPU) are important polymeric materials for seals. In competition with Acrylonitrile butadiene rubbers (NBR), TPU exhibits higher strength and a considerable better abrasion resistance. The advantage of NBR over TPU is a smaller compression set but however TPU excels in its much shorter processing cycle times. Generally a TPU is a block copolymer composed of hard and soft segments, which plays an important role in determining the material properties. TPU can be processed either to ready moulded parts or can be incorporated by multi component moulding, in both cases it shows decent mechanical properties. In the present work, the relationship between melt-process induced TPU morphology and resultant thermo mechanical properties were examined and determined by means of quasi-static tensile test, creep experiment, tension test and dynamical mechanical analysis (DMA). Scanning electron beam microscope (SEM) and differential scanning calorimeter (DSC) were used to study the morphology of the samples. A significant mathematical description of the stress-strain behaviour of TPU was found using a 3 term approach. Moreover it became evident that processing conditions such as processing temperature have crucial influence on morphology as well as short and long-term performance. To be more precise, samples processed at higher temperatures showed a lack of large hard segment agglomerates, a smaller strength for strains up to 250% and higher creep compliance.

36 MATERIALS SCIENCE↗

Effects of Sr, Ce and P on the microstructure and mechanical properties of rapidly solidified Al7Si alloys

Highlights: • Rapid solidification caused formation of nanoscaled Si particle chains. • Sr or Ce induced the columnar transition zone only at extremely high cooling rate. • Enhancement of hardness is attributed to fine dispersion of eutectic Si, grain refinement and the supersaturation of Si. • Sr or Ce caused further enhancement of hardness, attributing to Si modification. - Abstract: A series of Al7Si based alloys with trace addition of Sr, Ce or P were prepared using melt-spinning at two different high cooling rates, and the microstructure as well as the hardness of the ribbons was comprehensively studied. The results show that Sr or Ce induces the formation of columnar transition zone and modifies the morphology of eutectic Si phase from dispersed particle chains to fine fibers only at extremely high cooling rate. However, P has little effect on the microstructure of either α-Al or eutectic Si. Compared with conventional casting, the Al7Si ribbons exhibit extremely high hardness due to the fine dispersion of eutectic Si, the grain refinement and the supersaturation of Si. The hardness is further enhanced by Sr or Ce addition at extremely high cooling rate, especially for columnar and equiaxed zones, attributing to the modification effect on Si phase.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of extruded Mg-Gd-Y-Zn-Zr alloys filled with intragranular LPSO phases

Highlights: • Intragranular thin-platelet LPSO phases strongly restrict the DRX. • The low extrusion ratio fails to widely break the intragranular LPSO. • The large extrusion ratio results in the full DRX via the CDRX mechanism. • Finer DRX-ed grains and LPSO induce the higher yield strength and elongation. • The larger grain size causes an increase in the strain hardening rate. - Abstract: A comparison has been made on the dynamic recrystallization (DRX), texture, and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloys extruded with different ratios (ER, 36 and 7.1). Intragranular long-period stacking ordered (LPSO) phases strongly restrict the DRX by restraining the lattice rotation of α-Mg grains and hindering the migration of the boundaries of DRX-ed grains. Extrusion with ER of 36 can widely break the intragranular LPSO phases and create a fully DRX-ed microstructure with a relatively random texture, while the lower ER of 7.1 fails to break the LPSO and leads to a bimodal microstructure with a strong basal fiber texture. Finer DRX-ed grains and smaller LPSO phases account for the superior tensile yield strength and elongation of the ER36 alloy. However, the ultimate tensile strength of the ER7.1 alloy catches up because its larger grain size causes an increase in the strain hardening rate.

36 MATERIALS SCIENCE↗

Achieving superior mechanical properties: Tailoring multicomponent microstructure in AISI 9254 spring steel through a two-stage Q&P process and nanoscale carbide integration

In the pursuit of lightweight, durable steel, we have successfully developed a multicomponent structure in AISI 9254 spring steel using a two-stage quenching and partitioning (Q&P) process. The primary objective of this process was to engineer an optimized microstructure consisting of nanobainite, martensite, and nano-carbides. Utilizing the insights gained from the results of advanced techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atom probe tomography (APT) performed on the as-received AISI 9254 spring steel, we refined the quenching and partitioning (Q&P) path, leading to the successful establishment of a bainitic transformation for superior mechanical properties. Our tensile tests revealed a high yield strength (≈ 1600 ± 25 MPa) and ultimate tensile strength (≈ 1850 ± 50 MPa), along with considerable elongation (≈ 11.15 ± 0.25%). We also identified that pre-formed martensite lath defects and high silicon content play crucial roles during the Q&P process, preventing carbide coalescence and increasing strain-hardening capacity. Finally, this study demonstrates the potential of a Q&P process to generate high-strength, ductile steel for automotive and aerospace applications.

36 MATERIALS SCIENCE↗

Effect of preheat temperature and post-process treatment on the microstructure and mechanical properties of stainless steel 410 made via ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) is a solid-state manufacturing technology for producing near-net shape metallic parts combining additive ultrasonic metal welding and subtractive machining. Even though UAM has been demonstrated to produce robust metal builds in Al–Al, Al–Ti, Al-steel, Cu–Cu, Al–Cu, and other material systems, UAM welding of high strength steels has proven challenging. This study investigates process and post-processing methods to improve UAM steel weld quality and demonstrates the UAM fabrication of stainless steel 410 (SS 410) builds which possess, after post-processing, mechanical properties comparable with bulk material. Unlike UAM fabrication of softer metals, this study shows that increasing the baseplate temperature from 38°C (100°F) to 204°C (400°F) improves interfacial strength and structural homogeneity of the UAM steel samples. Further improvement in strength is achieved through post-processing. The hot isostatic pressing (HIP) post treatment improves the shear strength of UAM samples to 344 MPa from 154 MPa for as-welded samples. Microstructural analyses with SEM and EBSD show no evidence of body centered cubic (BCC) ferrite to face centered cubic (FCC) austenite transformation taking place during UAM welding of SS 410. The weld quality improvement of UAM steel at higher baseplate temperatures is believed to be caused by the reduction of the yield strength of SS 410 at elevated temperature. Finaly, HIP treatment is shown to increase the overall hardness of UAM SS 410 from 204 ± 7 HV to 240 ± 16 HV due to the formation of local pockets of martensite. Nanohardness tests show that the top of layer n is harder than the bottom of layer n+1 due to grain boundary strengthening.

36 MATERIALS SCIENCE↗

Effect of Zinc Interlayer in Microstructure Evolution and Mechanical Properties in Dissimilar Friction Stir Welding of Aluminum to Titanium

The welding of aluminum (Al) and titanium (Ti) is difficult and challenging due to the differences in their chemical and physical properties, and the formation of brittle intermetallic phases. In the present experiment, a zinc (Zn) interlayer was used during friction stir welding of Al to Ti. The weld was characterized in detail to understand the mechanisms associated with microstructural evolution and improvement in mechanical properties of the weld. X-ray computed tomography results reveal three-dimensional distribution of particles and flakes of titanium in the weld nugget. It was also observed that Ti particles are inhomogeneously distributed in the weld and the distribution depends on their morphology. Such a distribution of Ti was informative in understanding material flow. In addition, the consolidation of Zn in the Al matrix reveals the nature of material flow in the weld nugget as well. The importance of the Zn interlayer and mechanism of phase formation was explored in this study. It was characterized that the mechanical mixing of Zn with Al and Ti alters phase evolution and restricts the formation of conventional Al{sub 3}Ti intermetallic phase. The presence of zinc homogenizes elemental distribution and inhibits the formation of brittle intermetallic phases, which leads to a substantial improvement in mechanical properties of the weld.

36 MATERIALS SCIENCE↗

Influence of the synthesis method on the porosity, microstructure and electrical properties of La{sub 0.7}Sr{sub 0.3}MnO{sub 3} cathode materials

Lanthanum strontium manganite (La{sub 1-x}Sr{sub x}MnO{sub 3}, LSM) has been studied as a promising material for application as a cathode in solid oxide fuel cells. In the present work La{sub 0.7}Sr{sub 0.3}MnO{sub 3} nanopowders were synthesized by three different methods (combustion, citrate and solid-state) and characterized by thermal analysis, X-ray diffraction, physical adsorption of N{sub 2} and scanning electron microscopy. All powders exhibited single LSM phase formation with crystallite sizes in the range of 12-20 nm. Nanopowders were sintered at 1100 deg. C to produce porous pellets. The porosity, particle size and microstructure of LSM sintered bodies are strongly dependent on the preparation methodology. The samples synthesized by combustion and citrate methods presented smaller particle sizes and higher porosity after sintering than that derived from solid-state synthesis. However, the electrical conductivity, measured by two-probe technique, was very similar for all three samples.

36 MATERIALS SCIENCE↗

Investigating the effect of different shielding gas mixtures on microstructure and mechanical properties of 410 stainless steel fabricated via large scale additive manufacturing

Metal Big Area Additive Manufacturing (mBAAM) offers the potential to fabricate large scale tools at high deposition rates (15 lb/h+). 410 martensitic steel is a potential tooling material, owing to its low cost, good machinability and reasonable printability. During the mBAAM process, the shielding gas can have a significant impact on the material properties as well as the process cost. Therefore, the current study aims to understand the effect of different shielding gas mixtures on large-scale additive manufacturing of 410 martensitic stainless steel. We show that an argon mixture with 3% nitrogen gas produced the best performance in terms of maximum hardness and tensile strength, with much less scatter in tensile strength. He-Ar-CO 2 or tri-mix shielded samples showed a low tensile strength with wide scatter, due to stabilized delta ferrite in microstructure during printing. Both tri-mix and Ar-CO 2 shielded samples showed slightly higher porosity. Thus, we recommend the use of argon-3% nitrogen as a shielding gas mixture for processing 410 steel for tool applications, based on the relatively low cost of this gas mixture and the resulting higher hardness, higher dimensional stability, and lower porosity.

36 MATERIALS SCIENCE↗

Pyrochlore type semiconducting ceramic oxides in Ca-Ce-Ti-M-O system (M = Nb or Ta)-Structure, microstructure and electrical properties

A new series of pyrochlore type ceramic semiconducting oxides in Ca-Ce-Ti-M-O (M = Nb or Ta) system has been synthesized by the conventional ceramic route. The electrical conductivity measurements show that these oxides exhibit semiconducting behavior and the conductivity increases with the Ce content in the compound. Activation energy of the current carriers is in the range of 0.5-1.6 eV. The electrical conductivity in these oxides is due to the presence of Ce{sup 3+}, which remains in the reduced state without being oxidized to Ce{sup 4+} by structural stabilization. The photoluminescence and X-ray photoelectron spectroscopy analysis corroborate the presence of Ce in the 3+ state. Impedance spectral analysis is carried out to evaluate the transport properties and indicates that the conduction in these compounds is mainly due to electronic contribution. The X-ray powder diffraction and Raman spectroscopy analysis establishes that these oxides belong to a cubic pyrochlore type structure.

36 MATERIALS SCIENCE↗