Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LANDING SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Simulator study of a flight director display

A six degree of freedom, fixed base simulation study of the use of a flight director by general aviation pilots in an instrument landing system approach was conducted. An autopilot command law was used to drive the flight director needles. Time histories of the pilot aircraft display system responses and standard deviations and means of the glide slope and localizer errors were obtained. The pilot aircraft display system responses with the flight director were very similar to the autopilot aircraft responses. Without the flight director, the pilot aircraft display system exhibited less damping than with the flight director. The sensitivity of the flight director command laws was judged to be about as high as it could be by the test subjects. Thus, further improvement in the pilot aircraft display system performance by increasing the gains in the command laws was precluded.

Adams, J. J.↗

NASA's aviation safety - meteorology research programs

The areas covering the meteorological hazards program are: severe storms and the hazards to flight generated by severe storms; clear air turbulence; icing; warm fog dissipation; and landing systems. Remote sensing of ozone by satellites, and the use of satellites as data relays is also discussed.

Roger L. Winblade↗

Advanced symbology for general aviation approach to landing displays

A set of flight tests designed to evaluate the relative utility of candidate displays with advanced symbology for general aviation terminal area instrument flight rules operations are discussed. The symbology was previously evaluated as part of the NASA Langley Research Center's Terminal Configured Vehicle Program for use in commercial airlines. The advanced symbology included vehicle track angle, flight path angle and a perspective representation of the runway. These symbols were selectively drawn on a cathode ray tube (CRT) display along with the roll attitude, pitch attitude, localizer deviation and glideslope deviation. In addition to the CRT display, the instrument panel contained standard turn and bank, altimeter, rate of climb, airspeed, heading, and engine instruments. The symbology was evaluated using tracking performance and pilot subjective ratings for an instrument landing system capture and tracking task.

Bryant, W. H.↗

Review of NASA ACLS research

An experimental investigation was conducted to evaluate a method of maintaining stability of an air cushion vehicle and also to evaluate several concepts to brake and steer an ACLS-equipped vehicle. The investigation used a modified airboat equipped with an air cushion landing system. The pressure relief door stability concept was characterized by the ACLS pressure time histories. The pressure relief doors vented excess cavity and lobe pressures and consistently maintained vehicle heave and pitch stability. Braking concepts were characterized by the average deceleration of the vehicle. Reduced lobe flow and cavity venting braking concepts were evaluated in this program. The cavity venting concept demonstrated the best performance, producing decelerations on the test vehicle on the same order as moderate braking with conventional wheel brakes. Steering concepts were evaluated by recording the path taken while attempting to follow a prescribed maneuver. The steering concepts evaluated included using rudders only, using differential lobe flow, and using rudders combined with a lightly loaded, nonsteering center wheel. The latter concept proved to be the most accurate means of steering the vehicle on the ACLS, producing translational deviations which, while two to three times higher than those from conventional nose gear steering, were still felt to provide reasonably precise steering control for this type vehicle.

Daugherty, R. H.↗

Overview of NASA's programs

An overview of some of NASA's aviation related programs is presented. The areas discussed include: (1) severe storms; (2) clear air turbulence; (3) icing; (4) fog; and (5) landing systems.

Tobiason, A. R.↗

Use of flight simulation to develop terminal instrument procedures for transport category aircraft

In a collaborative effort between the FAA and NASA, a simulation was conducted to look at the issues involved with flying a large, widebody aircraft in the terminal area using MLS-RNAV procedures. A variety of approach paths, departure paths, and holding patterns were investigated during the course of the study, which included the participation of subject pilots. The simulation made use of paths designed by the FAA Office of Aviation Standards and employed Langley's Visual Motion Simulator (VMS) for their execution. Data obtained from this simulation will be used to support the joint FAA/USAF MLS flight test and demonstration project. This paper describes the flight simulation facility adapted to model terminal area maneuvers for jet transport aircraft using the Microwave Landing System (MLS). A description of the overall project will be presented first, along with a discussion of the guidance schemes used, followed by a description of the simulation hardware and software. A sample of the resulting data will also be presented.

Branstetter, J. R.↗

Design and development of a large diameter high pressure fast acting propulsion valve and valve actuator

The design and development of a large diameter high pressure quick acting propulsion valve and valve actuator is described. The valve is the heart of a major test facility dedicated to conducting full scale performance tests of aircraft landing systems. The valve opens in less than 300 milliseconds releasing a 46-centimeter- (18-in.-) diameter water jet and closes in 300 milliseconds. The four main components of the valve, i.e., valve body, safety shutter, high speed shutter, and pneumatic-hydraulic actuator, are discussed. This valve is unique and may have other aerospace and industrial applications.

Srinivasan, K. V.↗

A combined stochastic feedforward and feedback control design methodology with application to autoland design

A combined stochastic feedforward and feedback control design methodology was developed. The objective of the feedforward control law is to track the commanded trajectory, whereas the feedback control law tries to maintain the plant state near the desired trajectory in the presence of disturbances and uncertainties about the plant. The feedforward control law design is formulated as a stochastic optimization problem and is embedded into the stochastic output feedback problem where the plant contains unstable and uncontrollable modes. An algorithm to compute the optimal feedforward is developed. In this approach, the use of error integral feedback, dynamic compensation, control rate command structures are an integral part of the methodology. An incremental implementation is recommended. Results on the eigenvalues of the implemented versus designed control laws are presented. The stochastic feedforward/feedback control methodology is used to design a digital automatic landing system for the ATOPS Research Vehicle, a Boeing 737-100 aircraft. The system control modes include localizer and glideslope capture and track, and flare to touchdown. Results of a detailed nonlinear simulation of the digital control laws, actuator systems, and aircraft aerodynamics are presented.

Halyo, Nesim↗

Communication satellite technology trends

A chronology of space-Earth interconnectivity is presented. The Advanced Communications Technology Satellite (ACTS) system, Land Mobile Satellite, space-Earth antennas, impact of antenna size on coverage, intersatellite links are outlined. This presentation is represented by graphs and charts only.

Cuccia, Louis↗

Effect of motion cues during complex curved approach and landing tasks: A piloted simulation study

A piloted simulation study was conducted to examine the effect of motion cues using a high fidelity simulation of commercial aircraft during the performance of complex approach and landing tasks in the Microwave Landing System (MLS) signal environment. The data from these tests indicate that in a high complexity MLS approach task with moderate turbulence and wind, the pilot uses motion cues to improve path tracking performance. No significant differences in tracking accuracy were noted for the low and medium complexity tasks, regardless of the presence of motion cues. Higher control input rates were measured for all tasks when motion was used. Pilot eye scan, as measured by instrument dwell time, was faster when motion cues were used regardless of the complexity of the approach tasks. Pilot comments indicated a preference for motion. With motion cues, pilots appeared to work harder in all levels of task complexity and to improve tracking performance in the most complex approach task.

Scanlon, Charles H.↗

Analysis of a range estimator which uses MLS angle measurements

A concept that uses the azimuth signal from a microwave landing system (MLS) combined with onboard airspeed and heading data to estimate the horizontal range to the runway threshold is investigated. The absolute range error is evaluated for trajectories typical of General Aviation (GA) and commercial airline operations (CAO). These include constant intercept angles for GA and CAO, and complex curved trajectories for CAO. It is found that range errors of 4000 to 6000 feet at the entry of MLS coverage which then reduce to 1000-foot errors at runway centerline intercept are possible for GA operations. For CAO, errors at entry into MLS coverage of 2000 feet which reduce to 300 feet at runway centerline interception are possible.

Downing, David R.↗

Flight simulation of a wide-body transport aircraft to evaluate MLS-RNAV procedures

In a collaborative effort between the Federal Aviation Administration (FAA) NASA and the U.S. Air Force, a piloted simulation was conducted to look at the issues involved with flying a large, wide-body aircraft in the airport terminal area using Microwave Landing System Area Navigation (MLS)-RNAV procedures. A variety of approach paths, departure paths, and holding patterns were evaluated during the course of the study for operational use, flight technical errors, and safety. In addition, several methods for driving the horizontal situation indicator and flight director instruments were investigated along with needle sensitivity. The ultimate goal of the simulation was to develop and verify candidate paths and procedures prior to flight tests conducted in 1986/87. Subject pilots for the simulation study were provided by the FAA, NASA, the U.S. Air Force, and the airline industry.

Branstetter, James R.↗

B-737 flight test of curved-path and steep-angle approaches using MLS guidance

A series of flight tests were conducted to collect data for jet transport aircraft flying curved-path and steep-angle approaches using Microwave Landing System (MLS) guidance. During the test, 432 approaches comprising seven different curved-paths and four glidepath angles varying from 3 to 4 degrees were flown in NASA Langley's Boeing 737 aircraft (Transport Systems Research Vehicle) using an MLS ground station at the NASA Wallops Flight Facility. Subject pilots from Piedmont Airlines flew the approaches using conventional cockpit instrumentation (flight director and Horizontal Situation Indicator (HSI). The data collected will be used by FAA procedures specialists to develop standards and criteria for designing MLS terminal approach procedures (TERPS). The use of flight simulation techniques greatly aided the preliminary stages of approach development work and saved a significant amount of costly flight time. This report is intended to complement a data report to be issued by the FAA Office of Aviation Standards which will contain all detailed data analysis and statistics.

Branstetter, J. R.↗

Stereo 3-D and non-stereo presentations of a computer-generated pictorial primary flight display with pathway augmentation

Stereo 3-D was researched as a means to present cockpit displays which enhance a pilot's situational awareness while maintaining a desirable level of mental workload. The initial study at the NASA Langley Research Center used two different pathways-in-the-sky to augment a computer-generated pictorial primary flight display. One pathway resembled the outline of signposts, while the other pathway resembled a monorail. That display was configured for a curved approach to a landing such as could be used in a Microwave Landing System (MLS) approach. It could also be used for military transports which would have to fly a precision curved pathway. Each trial was initialized with the pilot on the desired flight path. After 2 seconds, he suddenly was shifted to one of eight flight path offsets. The pilot was then required to make the initial pitch and/or roll input to correct back to the nominal flight path. As soon as the input was made, the trial was over. No input was required for control trials with no flight path offset. Pilots responded statistically significantly faster when the display was presented in the stereo version than when it was presented in the nonstereo version.

Nataupsky, Mark↗

Independent Orbiter Assessment (IOA): FMEA/CIL assessment

The McDonnell Douglas Astronautics Company (MDAC) was selected to perform an Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL). Direction was given by the Orbiter and GFE Projects Office to perform the hardware analysis and assessment using the instructions and ground rules defined in NSTS 22206. The IOA analysis featured a top-down approach to determine hardware failure modes, criticality, and potential critical items. To preserve independence, the analysis was accomplished without reliance upon the results contained within the NASA and Prime Contractor FMEA/CIL documentation. The assessment process compared the independently derived failure modes and criticality assignments to the proposed NASA post 51-L FMEA/CIL documentation. When possible, assessment issues were discussed and resolved with the NASA subsystem managers. Unresolved issues were elevated to the Orbiter and GFE Projects Office manager, Configuration Control Board (CCB), or Program Requirements Control Board (PRCB) for further resolution. The most important Orbiter assessment finding was the previously unknown stuck autopilot push-button criticality 1/1 failure mode. The worst case effect could cause loss of crew/vehicle when the microwave landing system is not active. It is concluded that NASA and Prime Contractor Post 51-L FMEA/CIL documentation assessed by IOA is believed to be technically accurate and complete. All CIL issues were resolved. No FMEA issues remain that have safety implications. Consideration should be given, however, to upgrading NSTS 22206 with definitive ground rules which more clearly spell out the limits of redundancy.

Hinsdale, L. W.↗

Independent Orbiter Assessment (IOA): FMEA/CIL assessment

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. Direction was given by the Orbiter and GFE Projects Office to perform the hardware analysis and assessment using the instructions and ground rules defined in NSTS 22206. The IOA analysis features a top-down approach to determine hardware failure modes, criticality, and potential critical items. To preserve independence, the anlaysis was accomplished without reliance upon the results contained within the NASA and prime contractor FMEA/CIL documentation. The assessment process compares the independently derived failure modes and criticality assignments to the proposed NASA Post 51-L FMEA/CIL documentation. When possible, assessment issues are discussed and resolved with the NASA subsystem managers. The assessment results for each subsystem are summarized. The most important Orbiter assessment finding was the previously unknown stuck autopilot push-button criticality 1/1 failure mode, having a worst case effect of loss of crew/vehicle when a microwave landing system is not active.

Saiidi, Mo J.↗

High Altitude Ozone Research Balloon

In order to create a mission model of the high altitude ozone research balloon (HAORB) several options for flight preparation, altitude control, flight termination, and payload recovery were considered. After the optimal launch date and location for two separate HAORB flights were calculated, a method for reducing the heat transfer from solar and infrared radiation was designed and analytically tested. This provided the most important advantage of the HAORB over conventional balloons, i.e., its improved flight duration. Comparisons of different parachute configurations were made, and a design best suited for the HAORB's needs was determined to provide for payload recovery after flight termination. In an effort to avoid possible payload damage, a landing system was also developed.

Cauthen, Timothy A.↗

Mars Rover options

The paper will describe a nested set of Mars Rover options which are being considered. The option ranges include: low-to-high levels of technology, especially in autonomous activities; low (400 kg) to high (1500 kg) allowable mass; and coarse (100-meter) to fine (1-meter) knowledge of the terrain to be traversed. The options which will be selected for further study at the end of FY 1988 will be heavily dependent on such factors as the availability of precursor mission data (especially imaging) and the bounds on mass and volume imposed by the launch, Martian entry, and landing systems.

Pivirotto, Donna Shirley↗