Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “L CODES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Redesign and cascade tests of a supercritical controlled diffusion stator blade-section

A supercritical stator blade section, previously tested in cascade, and characterized by a flat-roof-top suction surface Mach number distribution, has been redesigned and retested. At near design conditions, the losses and air turning were improved over the original blade by 50 percent and 7 percent, respectively. The key element in the improved performance was a small blade reshaping. This produced a continuous flow acceleration over the first one-third chord of the suction surface which successfully prevented a premature laminar separation bubble. Several recently available inviscid analysis codes and one fully viscous (Navier-Stokes) analysis code were used in the redesign process. The validity of these codes was enhanced by the test results. Previously announced in STAR as N84-22533

Schmidt, J. F.↗
NASA NTRS1986

Single-Chip VLSI Reed-Solomon Encoder

Reed-Solomon (RS) encoder based on Berlekamp bit-serial multiplier algorithm. RS code standard, based on code words of 255 8-bit symbols, of which 223 symbols convey information and remaining 32 are check symbols. This code enables correction of up to 16 erroneous information symbols per word. Berlekamp algorithm based on code-generating polynomial with 32 roots that occur in reciprocal pairs. Choice of algorithm permits compact design.

Truong, T. K.↗
NASA NTRS1987

On minimizing the number of calculations in design-by-analysis codes

A method is presented for aerodynamic design for a specified pressure distribution, using analysis codes only. The method requires a very conservative number of analysis runs, and therefore is appropriate when the analysis code is a large code in terms of storage and/or running time. Three model problems illustrate some capabilities and limitations of the method.

Barger, Raymond L.↗
NASA NTRS1989

BRYNTRN: A baryon transport model

The development of an interaction data base and a numerical solution to the transport of baryons through an arbitrary shield material based on a straight ahead approximation of the Boltzmann equation are described. The code is most accurate for continuous energy boundary values, but gives reasonable results for discrete spectra at the boundary using even a relatively coarse energy grid (30 points) and large spatial increments (1 cm in H2O). The resulting computer code is self-contained, efficient and ready to use. The code requires only a very small fraction of the computer resources required for Monte Carlo codes.

Wilson, John W.↗
NASA NTRS1990

Recent advances in hypersonic technology

This paper will focus on recent advances in hypersonic aerodynamic prediction techniques. Current capabilities of existing numerical methods for predicting high Mach number flows will be discussed and shortcomings will be identified. Physical models available for inclusion into modern codes for predicting the effects of transition and turbulence will also be outlined and their limitations identified. Chemical reaction models appropriate to high-speed flows will be addressed, and the impact of their inclusion in computational fluid dynamics codes will be discussed. Finally, the problem of validating predictive techniques for high Mach number flows will be addressed.

Dwoyer, Douglas L.↗
NASA NTRS1993

Development of code evaluation criteria for assessing predictive capability and performance

Computational Fluid Dynamics (CFD), because of its unique ability to predict complex three-dimensional flows, is being applied with increasing frequency in the aerospace industry. Currently, no consistent code validation procedure is applied within the industry. Such a procedure is needed to increase confidence in CFD and reduce risk in the use of these codes as a design and analysis tool. This final contract report defines classifications for three levels of code validation, directly relating the use of CFD codes to the engineering design cycle. Evaluation criteria by which codes are measured and classified are recommended and discussed. Criteria for selecting experimental data against which CFD results can be compared are outlined. A four phase CFD code validation procedure is described in detail. Finally, the code validation procedure is demonstrated through application of the REACT CFD code to a series of cases culminating in a code to data comparison on the Space Shuttle Main Engine High Pressure Fuel Turbopump Impeller.

Lin, Shyi-Jang↗
NASA NTRS1994

Master-Oscillator/Power-Amplifier Laser System

Master-oscillator/power-amplifier (MOPA) laser system operates in continuous-wave mode or in amplitude-modulation (e.g., pulse) mode by modulation of oscillator current. Power amplifier is laser-diode-pumped neodymium:yttrium lithium fluoride (Nd:YLF) laser; oscillator is laser diode. Offers relatively high efficiency and power. Because drive current to oscillator modulated, external electro-optical modulator not needed. Potential uses include free-space optical communications, coded laser ranging, and generation of high-power, mode-locked pulses.

Yu, Anthony W.↗
NASA NTRS1992

Arcing in space structures in low Earth orbit

This report describes results of an experimental and theoretical program to investigate arcing of structures containing dielectric and conducting materials when they are biased negatively with respect to a plasma. An argon ion source generated Ar(+) ions of directed energy 20 to 40 eV and density approximately 10(exp 7) cm(exp -3) that impinged upon samples containing a dielectric material on top of a negatively biased Kovar plate. Arcing events were studied for bias voltages between -300 and -1000V with respect to the ion beam. The samples were Dow Corning 93-500 adhesive on Kovar, fused silica cover slips bonded on Kovar, and silicon solar cells mounted on Kovar. Measurements of discharge current, Kovar plate voltage, and radiation from the arc versus time were carried out. Microsecond duration exposure images and optical spectra in the 0.24 to 0.40 micron band were also acquired during arcing events. Arcing events were found to be associated with exposed adhesive and means were found to eliminate arcing altogether. The charging of a silica cover plate and the fields around the plate were calculated using a particle-in-cell code. Models were developed to explain the ignition of the arc and the physical processes occurring during the discharge.

Upschulte, B. L.↗
NASA NTRS1992

Automatic differentiation of advanced CFD codes for multidisciplinary design

Automated multidisciplinary design of aircraft and other flight vehicles requires the optimization of complex performance objectives with respect to a number of design parameters and constraints. The effect of these independent design variables on the system performance criteria can be quantified in terms of sensitivity derivatives which must be calculated and propagated by the individual discipline simulation codes. Typical advanced CFD analysis codes do not provide such derivatives as part of a flow solution; these derivatives are very expensive to obtain by divided (finite) differences from perturbed solutions. It is shown that sensitivity derivatives can be obtained accurately and efficiently using the ADIFOR source translator for automatic differentiation. In particular, it is demonstrated that the 3-D, thin-layer Navier-Stokes, multigrid flow solver called TLNS3D is amenable to automatic differentiation in the forward mode even with its implicit iterative solution algorithm and complex turbulence modeling. It is significant that by using computational differentiation, consistent discrete nongeometric sensitivity derivatives have been obtained from an aerodynamic 3-D CFD code in a relatively short time, e.g., O(man-week) not O(man-year).

Bischof, C.↗
NASA NTRS1994

NASA Lewis Research Center Workshop on Forced Response in Turbomachinery

A summary of the NASA Lewis Research Center (LeRC) Workshop on Forced Response in Turbomachinery in August, 1993 is presented. It was sponsored by the following NASA organizations: Structures, Space Propulsion Technology, and Propulsion Systems Divisions of NASA LeRC and the Aeronautics and Advanced Concepts & Technology Offices of NASA Headquarters. In addition, the workshop was held in conjunction with the GUIde (Government/Industry/Universities) Consortium on Forced Response. The workshop was specifically designed to receive suggestions and comments from industry on current research at NASA LeRC in the area of forced vibratory response of turbomachinery blades which includes both computational and experimental approaches. There were eight presentations and a code demonstration. Major areas of research included aeroelastic response, steady and unsteady fluid dynamics, mistuning, and corresponding experimental work.

Stefko, George L.↗
NASA NTRS1995

Measurement of precipitation induced FUV emission and Geocoronal Lyman Alpha from the IMI mission

This final report describes the activities of the Lockheed Martin Palo Alto Research Laboratory in studying the measurement of ion and electron precipitation induced Far Ultra-Violet (FUV) emissions and Geocoronal Lyman Alpha for the NASA Inner Magnetospheric Imager (IMI) mission. this study examined promising techniques that may allow combining several FUV instruments that would separately measure proton aurora, electron aurora, and geocoronal Lyman alpha into a single instrument operated on a spinning spacecraft. The study consisted of two parts. First, the geocoronal Lyman alpha, proton aurora, and electron aurora emissions were modeled to determine instrument requirements. Second, several promising techniques were investigated to determine if they were suitable for use in an IMI-type mission. Among the techniques investigated were the Hydrogen gas cell for eliminating cold geocoronal Lyman alpha emissions, and a coded aperture spectrometer with sufficient resolution to separate Doppler shifted Lyman alpha components.

Mende, Stephen B.↗
NASA NTRS2002

Two- and Three-Dimensional Numerical Experiments Representing Two Limiting Cases of an In-Line Pair of Finger Seal Components

The work presented here concerns the numerical development and simulation of the flow, pressure patterns and motion of a pair of fingers arranged behind each other and axially aligned in-line. The fingers represent the basic elemental component of a Finger Seal (FS) and form a tight seal around the rotor. Yet their flexibility allows compliance with rotor motion and in a passive-adaptive mode complies also with the hydrodynamic forces induced by the flowing fluid. While the paper does not treat the actual staggered configuration of a finger seal, the inline arrangement represents a first step towards that final goal. The numerical 2-D (axial-radial) and 3-D results presented herein were obtained using a commercial package (CFD-ACE+). Both models use an integrated numerical approach, which couples the hydrodynamic fluid model (Navier-Stokes based) to the solid mechanics code that models the compliance of the fingers.

Braun, M. J.↗
NASA NTRS2002

Computer based human-centered display system

A human centered informational display is disclosed that can be used with vehicles (e.g. aircraft) and in other operational environments where rapid human centered comprehension of an operational environment is required. The informational display integrates all cockpit information into a single display in such a way that the pilot can clearly understand with a glance, his or her spatial orientation, flight performance, engine status and power management issues, radio aids, and the location of other air traffic, runways, weather, and terrain features. With OZ the information is presented as an integrated whole, the pilot instantaneously recognizes flight path deviations, and is instinctively drawn to the corrective maneuvers. Our laboratory studies indicate that OZ transfers to the pilot all of the integrated display information in less than 200 milliseconds. The reacquisition of scan can be accomplished just as quickly. Thus, the time constants for forming a mental model are near instantaneous. The pilot's ability to keep up with rapidly changing and threatening environments is tremendously enhanced. OZ is most easily compatible with aircraft that has flight path information coded electronically. With the correct sensors (which are currently available) OZ can be installed in essentially all current aircraft.

Still, David L.↗
DOE OSTI2022

Development of the MCNP-ORIGEN activation automation tool

This paper introduces the MCNP-ORIGEN activation automation tool for streamlining the calculation of experiment source terms. This tool couples the Monte-Carlo radiation-transport solver, MCNP to the depletion tool, ORIGEN-S. To showcase its current capabilities, this paper presents an activation analysis exercise, which is conducted with Serpent, and the results are com- pared. The experiment consists in a 90%-enriched uranium sphere surrounded by light water. A non-fissile cylinder is placed in the water, representing an irradiation experiment. We conducted simulations for 2 different cylinder materials: iron and cobalt at two different temperatures: 300 K and 900 K. The exercise consists of an irradiation of 50 days at a constant power of 5 MW, followed by a decay of 50 days. These studies highlight the discrepancies between how the different tools handle nuclear data. Finally, the results underscore multiple areas of possible improvement.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

MultiPhATE2: code for functional annotation and comparison of phage genomes

To address a need for improved tools for annotation and comparative genomics of bacteriophage genomes, we developed multiPhATE2. As an extension of multiPhATE, a functional annotation code released previously, multiPhATE2 performs gene finding using multiple algorithms, compares the results of the algorithms, performs functional annotation of coding sequences, and incorporates additional search algorithms and databases to extend the search space of the original code. MultiPhATE2 performs gene matching among sets of closely related bacteriophage genomes, and uses multiprocessing to speed computations. MultiPhATE2 can be re-started at multiple points within the workflow to allow the user to examine intermediate results and adjust the subsequent computations accordingly. In addition, multiPhATE2 accommodates custom gene calls and sequence databases, again adding flexibility. MultiPhATE2 was implemented in Python 3.7 and runs as a command-line code under Linux or MAC operating systems. Full documentation is provided as a README file and a Wiki website.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Mycobacterium tuberculosis Phe-tRNA synthetase: structural insights into tRNA recognition and aminoacylation

Abstract Tuberculosis, caused by Mycobacterium tuberculosis, responsible for ∼1.5 million fatalities in 2018, is the deadliest infectious disease. Global spread of multidrug resistant strains is a public health threat, requiring new treatments. Aminoacyl-tRNA synthetases are plausible candidates as potential drug targets, because they play an essential role in translating the DNA code into protein sequence by attaching a specific amino acid to their cognate tRNAs. We report structures of M. tuberculosis Phe-tRNA synthetase complexed with an unmodified tRNAPhe transcript and either L-Phe or a nonhydrolyzable phenylalanine adenylate analog. High-resolution models reveal details of two modes of tRNA interaction with the enzyme: an initial recognition via indirect readout of anticodon stem-loop and aminoacylation ready state involving interactions of the 3′ end of tRNAPhe with the adenylate site. For the first time, we observe the protein gate controlling access to the active site and detailed geometry of the acyl donor and tRNA acceptor consistent with accepted mechanism. We biochemically validated the inhibitory potency of the adenylate analog and provide the most complete view of the Phe-tRNA synthetase/tRNAPhe system to date. The presented topography of amino adenylate-binding and editing sites at different stages of tRNA binding to the enzyme provide insights for the rational design of anti-tuberculosis drugs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Initial development of a high temperature life prediction method directly accounting for variability in material properties

This report presents the initial development of a life prediction method that accounts for the variability of the material properties in Grade 91 steel. We account for material variability by both fitting a variable 3-parameter Weibull distribution to the rupture data of the material and by quantifying the effect that the creep deformation properties have on stresses via a Monte Carlo approach. To ensure a reasonable time frame when applying Monte Carlo to the creep stress, we propose a methodology that models the material as an extremely viscous Stokes flow with a non-Newtonian viscosity, therefore solving the problem in a single step. We use the final probabilistic model for structural failure developed in this document to evaluate a Flat Head Vessel designed with the Section III, Division 5 ASME Boiler Pressure and Vessel Code rules with a 100,000h design life and assess its probability of premature failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗