SEARCH · Engineering Papers

Results for “Innovative Materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Pushing the Envelope—Moving Dynamic Building Envelope Thermal Energy Storage Systems Mainstream

Buildings contribute to nearly 40% of the U.S. national energy consumption and a significant portion of CO2 emissions. More importantly, disadvantaged communities are disproportionately affected by energy burden and thermal discomfort in their homes. This paper will discuss two novel DOE's BTO supported thermal energy storage (TES) integrated dynamic building envelope technologies, their ability to harvest ambient energy, and improve energy efficiency by reducing HVAC loads and peak electricity demand while enhancing energy and thermal resilience in buildings. The paper will also discuss the recent advancements that have made these systems more affordable and easier to integrate into new and existing buildings. The first solution is a thermally anisotropic building envelope (TABE) system that can redirect ambient thermal energy (heat or coolness) from diurnal outdoor conditions, solar irradiance, and night sky radiation from the envelope to a hydronic loop. The redirected thermal energy can be stored in a TABE-integrated thermal energy storage system and use the stored energy to offset HVAC energy use and peak demand. The second solution is an innovative plug-and-play thermal switch in the form of insertable plugs integrated with a phase change material (PCM). The plug can vary its thermal resistance based on the indoor and outdoor conditions, thus allowing preferential directional heat flow, and enhancing utilization of free ambient cooling and heating to charge/discharge the PCM, much like a solid-state economizer. While the fist solution can be actively controlled, the second solution is passive, requiring no external power, and work solely based on the ambient temperature.

Shrestha, Som↗

NASA NTRS1996

Concurrent Probabilistic Simulation of High Temperature Composite Structural Response

A computational structural/material analysis and design tool which would meet industry's future demand for expedience and reduced cost is presented. This unique software 'GENOA' is dedicated to parallel and high speed analysis to perform probabilistic evaluation of high temperature composite response of aerospace systems. The development is based on detailed integration and modification of diverse fields of specialized analysis techniques and mathematical models to combine their latest innovative capabilities into a commercially viable software package. The technique is specifically designed to exploit the availability of processors to perform computationally intense probabilistic analysis assessing uncertainties in structural reliability analysis and composite micromechanics. The primary objectives which were achieved in performing the development were: (1) Utilization of the power of parallel processing and static/dynamic load balancing optimization to make the complex simulation of structure, material and processing of high temperature composite affordable; (2) Computational integration and synchronization of probabilistic mathematics, structural/material mechanics and parallel computing; (3) Implementation of an innovative multi-level domain decomposition technique to identify the inherent parallelism, and increasing convergence rates through high- and low-level processor assignment; (4) Creating the framework for Portable Paralleled architecture for the machine independent Multi Instruction Multi Data, (MIMD), Single Instruction Multi Data (SIMD), hybrid and distributed workstation type of computers; and (5) Market evaluation. The results of Phase-2 effort provides a good basis for continuation and warrants Phase-3 government, and industry partnership.

Abdi, Frank↗

DOE OSTI2025

Glancing Angle Deposition in Gas Sensing: Bridging Morphological Innovations and Sensor Performances

Glancing Angle Deposition (GLAD) has emerged as a versatile and powerful nanofabrication technique for developing next-generation gas sensors by enabling precise control over nanostructure geometry, porosity, and material composition. Through dynamic substrate tilting and rotation, GLAD facilitates the fabrication of highly porous, anisotropic nanostructures, such as aligned, tilted, zigzag, helical, and multilayered nanorods, with tunable surface area and diffusion pathways optimized for gas detection. This review provides a comprehensive synthesis of recent advances in GLAD-based gas sensor design, focusing on how structural engineering and material integration converge to enhance sensor performance. Key materials strategies include the construction of heterojunctions and core–shell architectures, controlled doping, and nanoparticle decoration using noble metals or metal oxides to amplify charge transfer, catalytic activity, and redox responsiveness. GLAD-fabricated nanostructures have been effectively deployed across multiple gas sensing modalities, including resistive, capacitive, piezoelectric, and optical platforms, where their high aspect ratios, tailored porosity, and defect-rich surfaces facilitate enhanced gas adsorption kinetics and efficient signal transduction. These devices exhibit high sensitivity and selectivity toward a range of analytes, including NO2, CO, H2S, and volatile organic compounds (VOCs), with detection limits often reaching the parts-per-billion level. Emerging innovations, such as photo-assisted sensing and integration with artificial intelligence for data analysis and pattern recognition, further extend the capabilities of GLAD-based systems for multifunctional, real-time, and adaptive sensing. Finally, current challenges and future research directions are discussed, emphasizing the promise of GLAD as a scalable platform for next-generation gas sensing technologies.

Chemistry↗

NASA NTRS2008

Method for Thermal Spraying of Coatings Using Resonant-Pulsed Combustion

A method has been devised for high-volume, high-velocity surface deposition of protective metallic coatings on otherwise vulnerable surfaces. Thermal spraying is used whereby the material to be deposited is heated to the melting point by passing through a flame. Rather than the usual method of deposition from the jet formed from the combustion products, this innovation uses non-steady combustion (i.e. high-frequency, periodic, confined bursts), which generates not only higher temperatures and heat transfer rates, but exceedingly high impingement velocities an order of magnitude higher than conventional thermal systems. Higher impingement rates make for better adhesion. The high heat transfer rates developed here allow the deposition material to be introduced, not as an expensive powder with high surface-area-to-volume, but in convenient rod form, which is also easier and simpler to feed into the system. The nonsteady, resonant combustion process is self-aspirating and requires no external actuation or control and no high-pressure supply of fuel or air. The innovation has been demonstrated using a commercially available resonant combustor shown in the figure. Fuel is naturally aspirated from the tank through the lower Tygon tube and into the pulsejet. Air for starting is ported through the upper Tygon tube line. Once operation commences, this air is no longer needed as additional air is naturally aspirated through the inlet. A spark plug on the device is needed for starting, but the process carries on automatically as the operational device is resonant and reignites itself with each 220-Hz pulse.

Paxson, Daniel E.↗

DOE OSTI2023

Pillars of Innovation Across Southeast Idaho & the Interstate-15 Corridor

Since 1949, Idaho National Laboratory (INL) has been home to developing civilian and defense nuclear reactor technologies and managing spent nuclear fuel. Today, INL is the nation’s nuclear energy research laboratory, sustaining the safe and efficient operation of existing reactors, powering science in space, and breaking ground on the future fleet of advanced nuclear reactors. INL is only one of many rising technology resources in the region, however. Along the Interstate 15 (I-15) corridor, technology and cybersecurity industries and intellectual assets are rapidly expanding. Creating an innovation hub in this region would unite capabilities to solve current and future challenges in nuclear reactor sustainment and expanded deployment, integrated fuel cycle solutions, integrated energy systems, advanced materials and manufacturing for extreme environments, and secure and resilient cyber-physical systems.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRS2002

Rapid Prototyping of Continuous Fiber Reinforced Ceramic Matrix Composites

For ceramics to be used as structural components in high temperature applications, their fracture toughness is improved by embedding continuous ceramic fibers. Ceramic matrix composite (CMC) materials allow increasing the overall operating temperature, raising the temperature safety margins, avoiding the need for cooling, and improving the damping capacity, while reducing the weight at the same time. They also need to be reliable and available in large quantities as well. In this paper, an innovative rapid prototyping technique to fabricate continuous fiber reinforced ceramic matrix composites is described. The process is simple, robust and will be widely applicable to a number of high temperature material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The results of mechanical properties and microstructural characterization are presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts at an order of magnitude lower cost than current CVI and PIP processes.

Vaidyanathan, R.↗

NASA NTRS2003

Rapid Prototyping of Continuous Fiber Reinforced Ceramic Matrix Composites

Vaidyanathan, R.↗

DOE OSTI2025

Final report on assessment of molten salt corrosion testing of unirradiated and ion irradiated advanced manufactured high entropy alloys

Generation IV reactors and future fusion reactor designs have led to more demanding materials performance requirements due to their increased operating temperatures, corrosive coolants, and increased radiation doses compared to the current light-water reactor fleet. Among the innovative nuclear technologies under development, molten salt reactors stand out for their potential to offer superior fuel utilization, intrinsic safety characteristics, and economic viability. Of the proposed Generation IV designs, the gas fast reactor operates at 450 to 850°C and the molten salt reactor operates at 565 to 850°C, with the molten salt reactor design needing molten salt corrosion resistant materials [1, 2]. These increased temperatures and more extreme corrosion environments necessitate higher material performance, such as creep strength, radiation-tolerant microstructures, corrosion resistance, and high-temperature tensile properties. Hastelloy-N, a nickel-based alloy with additions of molybdenum and chromium, has been successfully employed to contain molten fluoride salt at temperatures up to 705°C. However, Hastelloy-N becomes embrittled upon neutron irradiation, primarily due to the accumulation of helium produced by (n,a) transmutation reactions. Furthermore, the corrosive nature of molten fluoride and chloride salts presents a formidable challenge, as these salts can react with and dissolve alloying elements such as Cr, Mo, and Fe, leading to selective leaching, loss of protective oxide layers, and accelerated degradation. High entropy alloys (HEAs) and refractory high entropy alloys (RHEAs) have emerged as a prominent area of interest, due to their ability to achieve tailored chemical compositions for specific applications. Unlike conventional alloys, HEAs are characterized by having multiple principal elements in equimolar or near equimolar ratios, leading to an unconventional alloying strategy [3]. This alloying strategy is believed to promote unique properties, such as single-phase stabilization of chemically compatible elements, lattice distortion effects due to atomic radius differences, and proposed sluggish diffusion effects. For extreme-environment applications, RHEAs have garnered much research interest because of the possibility of creating relatively ductile materials that can operate in extremely high-temperature environments, beyond the operating temperatures where other Ni-based superalloys begin to lose strength [4-6]. Idaho National Laboratory (INL) initiated a joint international effort with the Czech Republic to explore the feasibility of manufacturing HEAs for high-temperature nuclear applications using advanced manufacturing. This effort was funded at INL by the United States Department of Energy's Office of Nuclear Energy under the Advanced Reactor Technologies and Advanced Materials and Manufacturing Technologies (AMMT) Program. The HEAs were specifically designed for the corrosive and irradiation environments experienced in gas-cooled fast reactors, molten salt reactors, and fusion power. These alloys have been manufactured by multiple processes to determine the impact of manufacturing processes on the performance of the alloys in corrosive and irradiation environments. Preliminary molten salt corrosion testing showed that equimolar MoNbTiV and MoNbTi alloys exhibit exceptional performance, with arc-melted variants demonstrating only minimal degradation after 1000 hours of exposure to molten chloride salt at 700°C. Conversely, Nb2TiVZr2 showed significant molten salt corrosion susceptibility and microstructural instability during high-temperature molten salt exposures, and was, therefore deemed unfit for molten salt reactor applications. The MoNbTiV, MoNbTi, and Nb2TiVZr2 alloys were further evaluated through ion irradiation experiments conducted at the Michigan Ion Beam Laboratory at the University of Michigan. The microstructural stability and the evolution of irradiation-induced defects were characterized to assess the irradiation resistance of each of these alloys.

36 - MATERIALS SCIENCE↗

DOE OSTI2024

Analysis as a Key Guiding Tool for Waste Carbon Utilization

Over a billion metric tons of waste and biomass are projected to be available in a future mature market in the United States. These resources represent an opportunity to decouple chemical and polymer production from conventional fossil fuel feedstocks, but such a broad solution space can also make for challenging decision-making. This talk will provide researchers with an introduction to key analysis techniques such as techno-economic analysis, life cycle assessment, and material flow analysis: how they are conducted and how they can be used to benchmark the costs, environmental impacts, and circularity of new innovations as well as to identify opportunities for prioritization and optimization. Using a series of examples related to plastic recycling and chemical manufacturing, we will explore how analysis can guide where and how to leverage waste carbon in supply chains towards a future circular economy.

chemical↗

NASA NTRS1997

Unique Tuft Test Facility Dramatically Reduces Brush Seal Development Costs

Brush seals have been incorporated in the latest turbine engines to reduce leakage and improve efficiency. However, the life of these seals is limited by wear. Studies have shown that optimal sealing characteristics for a brush seal occur before the interference fit between the brush and shaft is excessively worn. Research to develop improved tribopairs (brush and coating) with reduced wear and lower friction has been hindered by the lack of an accurate, low-cost, efficient test methodology. Estimated costs for evaluating a new material combination in an engine company seal test program are on the order of $100,000. To address this need, the NASA Lewis Research Center designed, built, and validated a unique, innovative brush seal tuft tester that slides a single tuft of brush seal wire against a rotating shaft under controlled loads, speeds, and temperatures comparable to those in turbine engines. As an initial screening tool, the brush seal tuft tester can tribologicaly evaluate candidate seal materials for 1/10th the cost of full-scale seal tests. Previous to the development of the brush seal tuft tester facility, most relevant tribological data had been obtained from full-scale seal tests conducted primarily to determine seal leakage characteristics. However, from a tribological point of view, these tests included the confounding effects of varying contact pressures, bristle flaring, high-temperature oxidation, and varying bristle contact angles. These confounding effects are overcome in tuft testing. The interface contact pressures can be either constant or varying depending on the tuft mounting device, and bristle wear can be measured optically with inscribed witness marks. In a recent cooperative program with a U.S. turbine engine manufacturer, five metallic wire candidates were tested against a plasma-sprayed Nichrome-bonded chrome carbide. The wire materials used during this collaboration were either nickel-chrome- or cobaltchrome-based superalloys. These tests corroborated full-scale seal test results and provided insight into previously untested combinations. As the cycle temperature for improved efficiency turbine engines increases, new brush seal materials combinations must be considered. Future brush seal tuft testing will include both metallic and ceramic bristles versus commercial and NASA-developed shaft coatings. The ultimate goal of this work is to expand the current data base so that seal designers can tailor brush seal materials to specific applications.

Fellenstein, James A.↗

DOE OSTI2020

Materials and Fuels Complex Five-Year Investment Strategy (FY2020-FY2024)

The Department of Energy Office of Nuclear Energy (DOE-NE) mission is to provide the research, development, and demonstration (RD&D) foundation to extend the lives of the current operating reactor fleet, develop the next generation of nuclear reactors, and provide integrated nuclear fuel cycle solutions. The Materials and Fuels Complex (MFC) serves as the foundation of a nuclear RD&D enabling test bed at Idaho National Laboratory (INL) and is an integral part of a National Reactor Innovation Center (NRIC) strategy. MFC facilities focus on developing and maintaining RD&D capabilities that can increase research throughput, reduce barriers to deployment, and facilitate commercialization of new ideas and technologies for clean and secure sources of energy. This document is a complimentary document to the Materials and Fuels Complex Five-Year Mission Strategy FY-20 – FY-24 (INL/EXT-20-57224) that defines specific implementation strategies for increasing research capability and throughput through targeted investments in research facilities, research instruments, and research staff. Refer to INL/EXT-20-57224 for details about MFC, its capabilities, and the overall mission strategy for the Materials and Fuels Complex.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Location-Dependent Mechanical Property Evaluation on Additively Manufacture Materials

This report summarizes research activities conducted at Argonne National Laboratory in support of the development, qualification and certification of additively manufactured (AM) metallic components to allow for innovative reactor design and licensing for the Transformational Challenge Reactor (TCR). Focus is on the evaluation of high temperature mechanical properties including creep and fatigue of 316L stainless steel manufactured by the laser powder bed fusion process. Creep behavior of AM 316L stainless steel was evaluated for rods printed by either or a combination of both lasers of the dual-laser system of a Concept Laser-M2 printer to examine the consistency across the build plate. Creep tests were conducted at temperatures of 550, 575, 600, and 650°C and stresses between 175 and 300 MPa using ASTM standard-sized specimens. The effect of heat treatments at different temperatures on creep properties of AM 316L SS was examined to understand the processing-microstructure-property relationship. Fatigue properties of AM 316L SS were investigated for two print geometries (rod and plate) and in two build orientations of printed plates. Locations of specimens in the build were carefully tracked such that the testing data can be directly related to location-specific in situ data to establish links between printing process, post-printing treatment, microstructure and mechanical properties. The work is to support the development of a digital platform informed approach to AM component qualification and certification for nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRSDate not supplied

Reduced Cost NiTi-Alloy Bearings Made Via Near Net Shape Powder Metallurgy Processes

NiTi alloys are emerging as an attractive bearing race material for bearings exposed to high static loads and highly corrosive environments. One obstacle yet to be overcome is the intrinsically high relative cost of these materials compared to traditional bearing steels. Traditional net-shape powder metallurgy methods, such as cold-press and sinter, are not applicable to NiTi alloys because they require hot isostatic pressing (HIP) to achieve full density, flaw free microstructures. Recently, innovative powder metallurgy processing has been successful in forming bearing ring blank shapes through the use of geometrically tailored HIP containers. Microstructural evaluations show that ring blanks made from this process are comparable to material made using conventional HIP containers while substantially reducing material usage.

bearings↗

DOE OSTI2026

Mechanical Behavior of Neutron Irradiated Refractory Multi-Principal Element Alloys Processed via Spark Plasma Sintering

The search for advanced materials capable of withstanding the extreme conditions of Generation IV reactors is a critical area in materials science research. These reactors operate under severe environments, including high temperatures, corrosion, stress, and irradiation damage. Consequently, there is a need for innovative alloy systems to ensure the reliability and longevity of proposed Generation IV reactor components. Refractory multi-principal-element alloys (RMPEA) have emerged as a promising candidate due to their exceptional properties. These alloys, characterized by their composition of multiple principal elements in near-equiatomic ratios, exhibit superior resistance to irradiation damage, reduced void swelling, enhanced microstructural stability, and minimal irradiation-induced hardening. While initial studies on RMPEAs have shown promising results, most research has been limited to thin films, nanocrystalline microstructures, and ion irradiation, which do not accurately represent the behavior of bulk materials. To address this gap, our research focused on the neutron irradiation of bulk RMPEAs. We aim to conduct comprehensive post-irradiation examinations (PIE) of RMPEAs irradiated at the Advanced Test Reactor at Idaho National Laboratory. The RMPEAs were synthesized using spark plasma sintering (SPS) with mechanically alloyed metallurgical powder. The RMPEA specimens are a MoNbTi alloy system with additions of -Zr, and -ZrV. Furthermore, PIE consisted of mechanical testing and advanced materials characterization. The mechanical testing consisted of sub-sized tensile testing, micro- and nano- indentation. Microstructural characterization included scanning electron microscopy and transmission electron microscopy. Mechanical testing coupled with advanced microscopy techniques provides insight into phase morphology and its effects on the mechanical properties of the RMPEA specimens. The results indicate that both pristine and irradiated RMPEA specimens exhibited brittle behavior during tensile testing, which can be attributed to their heterogeneous microstructure. The SPS manufacturing process did not include any post treatment, which resulted in a heterogeneous microstructure. Energy-dispersive X-ray spectroscopy revealed the presence of intermetallic such as laves phases within the microstructure. Specifically, Ti-rich precipitates were observed in the MoNbTi specimen, while Mo-rich precipitates were found in the MoNbTiZrV specimen. Nano-hardness testing of pristine samples showed that the laves phases exhibited higher hardness values compared to the matrix phase, suggesting that precipitate hardening is likely the dominant hardening mechanism in these specimens. The results from this work will be used to build a finite element model to predict mechanical behavior of future MPEA compositions. Thus, enabling for a streamlined approach to developing novel MPEAs for the nuclear industry.

36 - MATERIALS SCIENCE↗

DOE OSTI2026

A Reflection on the Evolution of Sodium/Metal Chloride (ZEBRA) Batteries and Lithium-Ion Cathode Materials (1975–2025): A Tribute to Johan Coetzer

This narrative summarizes, in retrospect, the enormous and quietly-conducted contribution of Dr Johan Coetzer, a South African scientist and entrepreneur, to the discovery, development and implementation of the high temperature sodium—metal chloride “ZEBRA” battery (Na/β-Al 2 O 3 , NaAlCl 4 /MCl 2 (M = Ni, Fe)). Here, this research activity was initiated in the mid 1970’s at the Council for Scientific and Industrial Research (CSIR) in South Africa and subsequently developed primarily in partnership with the Atomic Energy Research Establishment (AERE, Harwell, UK), Beta R&D (Derby, UK) and Daimler Benz (Germany), before being transferred to industry worldwide for electric vehicle and energy storage applications, albeit at a relatively low production rate. Coetzer’s wide-ranging, innovative and, at times, unconventional scientific approach also laid the foundation for the discovery and implementation of manganese-based spinel and layered metal oxide cathode materials for the Li-ion battery industry.

ZEBRA Battery↗

DOE OSTI2024

An Integrated Electrochemical Approach to the Precision Synthesis of Sustainable Catalyst Materials

There is a pressing need to replace critical materials such as platinum group elements (PGE) in applications related to energy. This work responds to the need for fundamental principles of materials design to replace these metals by addressing a gap in the understanding of how to precisely control the surface structure of nanoscale materials. Electrochemical nanomaterials synthesis, such as techniques developed in the PI’s research group, expands the toolbox of available synthetic handles to include both electrochemical and chemical parameters, providing access to control over synthetic conditions in ways that are not possible in purely chemical nanoparticle growth. However, electrochemical materials synthesis (electrodeposition) is inherently serial, limiting throughput and preventing widespread implementation. Initial efforts in the short period of this award resulted in an innovative, high throughput, parallel approach to synthetic discovery for the electrodeposition of shaped metal nanoparticles that overcomes this limitation. Looking ahead, this work establishes an important capability that will enable researchers to push boundaries in the shape control of nanoparticles composed of non-PGE such as copper, iron, nickel, or cobalt.

36 MATERIALS SCIENCE↗

NASA NTRS2016

Innovation at the Edge of Space- An Engine for Global Opportunities

Microgravity based commercial opportunities are broad, with applications ranging from fiber optics, device-grade semiconductor crystals, space beads, new materials, cells microencapsulation, 3D tissues and cell cultures, genetic and molecular changes of immune suppression, protein and virus crystal growth, perfume and hair care. To date, primarily the knowledge gained from observing and understanding new end states of systems unraveled in microgravity has been translated into unique technologies and business opportunities on Earth. In some instances existing flight qualified hardware is immediately available for commercial RD for small-scale in-space manufacturing. Overall, products manufactured in microgravity have key properties usually surpassing the best terrestrial counterparts. Commercially, these products have an attractive touch of space which aids in marketing.The talk will addresses the potential benefits of microgravity research for a variety of terrestrial markets by (1) surveying the level of awareness and interest of parties from different commercial sectors (2) assessing the potential of microgravity to stimulate innovation in future product development and (3) formulating a synergistic strategy to use microgravity for economic growth and public benefit.Our findings originating primarily from discussions with 100+ non-aerospace private companies among the high-tech Silicon Valley ecosystem, show that the opportunities and benefits of using the ISS are largely not considered by experts, primarily due to a lack of awareness of the breadth of terrestrial applications that have been enabled or enhanced by microgravity RD. Based on this dialogue, the concept of microgravity verticals is developed to translate the benefits of the microgravity environment into blue ocean business opportunities for various key US commercial sectors.

orbital economy↗

DOE OSTI2023

Computation of high-frequency magnetoelastic waves in layered materials

Here, the direct calculation of magnetoelastic wave dispersion in layered media is presented using an efficient, accurate computational technique. The governing, coupled equations for elasticity and magnetism, the Navier and Landau-Lifshitz equations, respectively, are linearized to form a quadratic eigenvalue problem that determines a complex web of wave-number–frequency dispersion branches and their corresponding mode profiles. Numerical discretization of the eigenvalue problem via a spectral collocation method (SCM) is employed to determine the complete dispersion maps for both a single, finite-thickness magnetic layer and a finite magnetic-nonmagnetic double-layer. The SCM, previously used to study elastic waves in nonmagnetic media, is fast, accurate, and adaptable to a variety of sample configurations and geometries. Emphasis is placed on the extremely high-frequency regimes being accessed in ultrafast magnetism experiments. The dispersion maps and modes provide insight into how energy propagates through the coupled system, including how energy can be transferred between elastic- and magnetic-dominated waves as well as between different layers. The numerical computations for a single layer are further understood by a simplified analytical calculation in the high-frequency, exchange-dominated regime where the resonance condition required for energy exchange (an anticrossing) between quasi-elastic and quasi-magnetic dispersion branches is determined. Nonresonant interactions are shown to be well approximated by the dispersion of uncoupled elastic and magnetic waves. The methods and results provide fundamental theoretical tools to model and understand current and future magnetic devices powering spintronic innovation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗