Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IDENTIFICATION SYSTEMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

A Sparse Matrix Approach for Simultaneous Quantification of Nystagmus and Saccade

The vestibulo-ocular reflex (VOR) consists of two intermingled non-linear subsystems; namely, nystagmus and saccade. Typically, nystagmus is analysed using a single sufficiently long signal or a concatenation of them. Saccade information is not analysed and discarded due to insufficient data length to provide consistent and minimum variance estimates. This paper presents a novel sparse matrix approach to system identification of the VOR. It allows for the simultaneous estimation of both nystagmus and saccade signals. We show via simulation of the VOR that our technique provides consistent and unbiased estimates in the presence of output additive noise.

Kukreja, Sunil L.↗
NASA NTRS2012

Nonlinear Aerodynamic Modeling From Flight Data Using Advanced Piloted Maneuvers and Fuzzy Logic

Results of the Aeronautics Research Mission Directorate Seedling Project Phase I research project entitled "Nonlinear Aerodynamics Modeling using Fuzzy Logic" are presented. Efficient and rapid flight test capabilities were developed for estimating highly nonlinear models of airplane aerodynamics over a large flight envelope. Results showed that the flight maneuvers developed, used in conjunction with the fuzzy-logic system identification algorithms, produced very good model fits of the data, with no model structure inputs required, for flight conditions ranging from cruise to departure and spin conditions.

Brandon, Jay M.↗
NASA NTRS2013

Dynamic Modeling Accuracy Dependence on Errors in Sensor Measurements, Mass Properties, and Aircraft Geometry

A nonlinear simulation of the NASA Generic Transport Model was used to investigate the effects of errors in sensor measurements, mass properties, and aircraft geometry on the accuracy of dynamic models identified from flight data. Measurements from a typical system identification maneuver were systematically and progressively deteriorated and then used to estimate stability and control derivatives within a Monte Carlo analysis. Based on the results, recommendations were provided for maximum allowable errors in sensor measurements, mass properties, and aircraft geometry to achieve desired levels of dynamic modeling accuracy. Results using other flight conditions, parameter estimation methods, and a full-scale F-16 nonlinear aircraft simulation were compared with these recommendations.

Grauer, Jared A.↗
NASA NTRS2013

Dependence of Dynamic Modeling Accuracy on Sensor Measurements, Mass Properties, and Aircraft Geometry

The NASA Generic Transport Model (GTM) nonlinear simulation was used to investigate the effects of errors in sensor measurements, mass properties, and aircraft geometry on the accuracy of identified parameters in mathematical models describing the flight dynamics and determined from flight data. Measurements from a typical flight condition and system identification maneuver were systematically and progressively deteriorated by introducing noise, resolution errors, and bias errors. The data were then used to estimate nondimensional stability and control derivatives within a Monte Carlo simulation. Based on these results, recommendations are provided for maximum allowable errors in sensor measurements, mass properties, and aircraft geometry to achieve desired levels of dynamic modeling accuracy. Results using additional flight conditions and parameter estimation methods, as well as a nonlinear flight simulation of the General Dynamics F-16 aircraft, were compared with these recommendations

Grauer, Jared A.↗
NASA NTRS2014

Recent Progress in Heliogyro Solar Sail Structural Dynamics

Results from recent National Aeronautics and Space Administration (NASA) research on the structural dynamics and control characteristics of heliogyro solar sails are summarized. Specific areas under investigation include coupled nonlinear finite element analysis of heliogyro membrane blade with solar radiation pressure effects, system identification of spinning membrane structures, solarelastic stability analysis of heliogyro solar sails, including stability during blade deployment, and results from small-scale in vacuo dynamics experiments with spinning high-aspect ratio membranes. A low-cost, rideshare payload heliogyro technology demonstration mission concept, used as a mission context for these heliogyro structural dynamics and solarelasticity investigations, is also described.

Wilkie, William K.↗
NASA NTRS2014

Vertical Spin Tunnel Testing and Stability Analysis of Multi-Mission Earth Entry Vehicles

Multi-Mission Earth Entry Vehicles (MMEEVs) are blunt-body vehicles designed with the purpose of transporting payloads from space to the surface of the Earth. To achieve high reliability and minimum weight, MMEEVs avoid using limited-reliability systems, such as parachutes, retro-rockets, and reaction control systems and rely on the natural aerodynamic stability of the vehicle throughout the Entry, Descent, and Landing phases of flight. Testing in NASA Langley's 20-FT Vertical Spin Tunnel (20-FT VST), dynamically-scaled MMEEV models was conducted to improve subsonic aerodynamic models and validate stability criteria for this class of vehicle. This report documents the resulting data from VST testing for an array of 60-deg sphere-cone MMEEVs. Model configurations included were 1.2 meter, and 1.8 meter designs. The addition of a backshell extender, which provided a 150% increase in backshell diameter for the 1.2 meter design, provided a third test configuration. Center of Gravity limits were established for all MMEEV configurations. An application of System Identification (SID) techniques was performed to determine the aerodynamic coefficients in order to provide databases for subsequent 6-degree-of-freedom simulations.

Glaab, Louis J.↗
NASA NTRS2014

A Generic Nonlinear Aerodynamic Model for Aircraft

A generic model of the aerodynamic coefficients was developed using wind tunnel databases for eight different aircraft and multivariate orthogonal functions. For each database and each coefficient, models were determined using polynomials expanded about the state and control variables, and an othgonalization procedure. A predicted squared-error criterion was used to automatically select the model terms. Modeling terms picked in at least half of the analyses, which totalled 45 terms, were retained to form the generic nonlinear aerodynamic (GNA) model. Least squares was then used to estimate the model parameters and associated uncertainty that best fit the GNA model to each database. Nonlinear flight simulations were used to demonstrate that the GNA model produces accurate trim solutions, local behavior (modal frequencies and damping ratios), and global dynamic behavior (91% accurate state histories and 80% accurate aerodynamic coefficient histories) under large-amplitude excitation. This compact aerodynamics model can be used to decrease on-board memory storage requirements, quickly change conceptual aircraft models, provide smooth analytical functions for control and optimization applications, and facilitate real-time parametric system identification.

Grauer, Jared A.↗
NASA NTRS2016

In-Flight Pitot-Static Calibration

A GPS-based pitot-static calibration system uses global output-error optimization. High data rate measurements of static and total pressure, ambient air conditions, and GPS-based ground speed measurements are used to compute pitot-static pressure errors over a range of airspeed. System identification methods rapidly compute optimal pressure error models with defined confidence intervals.

Foster, John V.↗
NASA NTRS2017

New Flutter Analysis Technique for Time-Domain Computational Aeroelasticity

A new time-domain approach for computing flutter speed is presented. Based on the time-history result of aeroelastic simulation, the unknown unsteady aerodynamics model is estimated using a system identification technique. The full aeroelastic model is generated via coupling the estimated unsteady aerodynamic model with the known linear structure model. The critical dynamic pressure is computed and used in the subsequent simulation until the convergence of the critical dynamic pressure is achieved. The proposed method is applied to a benchmark cantilevered rectangular wing.

HWB aircraft↗
NASA NTRS2017

GOES-R Active Vibration Damping Controller Design, Implementation, and On-Orbit Performance

GOES-R series spacecraft feature a number of flexible appendages with modal frequencies below 3.0 Hz which, if excited by spacecraft disturbances, can be sources of undesirable jitter perturbing spacecraft pointing. In order to meet GOES-R pointing stability requirements, the spacecraft flight software implements an Active Vibration Damping (AVD) rate control law which acts in parallel with the nadir point attitude control law. The AVD controller commands spacecraft reaction wheel actuators based upon Inertial Measurement Unit (IMU) inputs to provide additional damping for spacecraft structural modes below 3.0 Hz which vary with solar wing angle. A GOES-R spacecraft dynamics and attitude control system identified model is constructed from pseudo-random reaction wheel torque commands and IMU angular rate response measurements occurring over a single orbit during spacecraft post-deployment activities. The identified Fourier model is computed on the ground, uplinked to the spacecraft flight computer, and the AVD controller filter coefficients are periodically computed on-board from the Fourier model. Consequently, the AVD controller formulation is based not upon pre-launch simulation model estimates but upon on-orbit nadir point attitude control and time-varying spacecraft dynamics. GOES-R high-fidelity time domain simulation results herein demonstrate the accuracy of the AVD identified Fourier model relative to the pre-launch spacecraft dynamics and control truth model. The AVD controller on-board the GOES-16 spacecraft achieves more than a ten-fold increase in structural mode damping of the fundamental solar wing mode while maintaining controller stability margins and ensuring that the nadir point attitude control bandwidth does not fall below 0.02 Hz. On-orbit GOES-16 spacecraft appendage modal frequencies and damping ratios are quantified based upon the AVD system identification, and the increase in modal damping provided by the AVD controller for each structural mode is presented. The GOES-16 spacecraft AVD controller frequency domain stability margins and nadir point attitude control bandwidth are presented along with on-orbit time domain disturbance response performance.

Active Vibration Damping↗
NASA NTRS2018

Characterizing Aerodynamic Damping of a Supersonic Missile with CFD

Time accurate solutions of the Euler and Navier{Stokes equations are used as an approach to elucidate aerodynamic coefficients that include rigid body motion effects. The Army-Navy Finner geometry is used for work flow development due to its simple shape, inexpensive grid generation, and available literature that include aerodynamic damping derivatives obtained from ight test, wind tunnel tests, and computational fluid dynamics. Supersonic conditions for pitch and roll damping include angles of attack up to 90 deg. Aerodynamic responses due to rigid body maneuvers with prescribed wind incidence angles and body rates are computed using the DoD CREATE Kestrel and NASA FUN3D flow solvers. First, reference numerical and experimental results provide validation of aero- dynamic damping terms computed by traditional periodic motion in roll and pitch. Next, individual, impulse motion inputs provide the canonical responses for general input-output modeling based on classical superposition and convolution concepts. Finally, simultaneous impulse excitation of all inputs provides an efficient system identification training scenario for accurate aerodynamic model construction in state space via the NASA Sys- tem/Observer/Controller Identification Toolbox.

Shelton, Andrew↗
NASA NTRS2018

Fuzzy Modeling and Parallel Distributed Compensation for Aircraft Flight Control from Simulated Flight Data

A method is described that combines fuzzy system identification techniques with Parallel Distributed Compensation (PDC) to develop nonlinear control methods for aircraft using minimal a priori knowledge, as part of NASA’s Learn-to-Fly initiative. A fuzzy model was generated with simulated flight data, and consisted of a weighted average of multiple linear time invariant state-space cells having parameters estimated using the equation-error approach and a least-squares estimator. A compensator was designed for each subsystem using Linear Matrix Inequalities (LMI) to guarantee closed-loop stability and performance requirements. This approach is demonstrated using simulated flight data to automatically develop a fuzzy model and design control laws for a simplified longitudinal approximation of the F-16 nonlinear flight dynamics simulation. Results include a comparison of flight data with the estimated fuzzy models and simulations that illustrate the feasibility and utility of the combined fuzzy modeling and control approach.

Weinstein, Rose↗
NASA NTRSDate not supplied

Aerodynamic Parameter Estimation Using Reconstructed Turbulence Measurements

A classical method for reconstructing atmospheric turbulence from onboard measurements of airdata and inertial sensors was improved. The reconstructed turbulence was included in a system identification analysis to estimate nondimensional stability and control derivatives in a longitudinal short period model using the maximum likelihood equation-error method with Fourier transform data. Practical aspects of the approach are discussed, such as reconstruction accuracy, data collinearity, model structure, and real-time estimation. Results using simulation and flight test data for a subscale airplane indicated that accurate turbulence reconstructions and parameter estimates could be obtained from maneuvering flight in high levels of turbulence.

Jared A Grauer↗
NASA NTRSDate not supplied

Preliminary Steps in Developing Rapid Aero Modeling Technology

The Rapid Aero Modeling (RAM) approach is a method to efficiently and automatically obtain aerodynamic models during testing, significantly saving time and resources. Motivation for this technology results from demand for experimental efficiency and model fidelity that has increased with growing aircraft complexity and aerodynamic nonlinearities. These issues are typical in the responses presented by a class of vehicles categorized as Urban Air Mobility aircraft where many features from both airplane and rotorcraft are present. For UAM configurations, with typically many more factors than conventional aircraft, traditional test methods can lead to increased costs and missed interactions. RAM guides the test to obtain high-fidelity, statistically rigorous aircraft models, and the approach is applicable to computational, ground, or flight-test experiments. It combines concepts from Design of Experiment theory and Aircraft System Identification theory that allow the user the freedom to choose, in advance of the test, a specific level of fidelity typically, in terms of prediction error. RAM only collects data required to meet the user-specified fidelity and fidelity is only limited by the facility and test article capabilities. An initial wind tunnel test to support development of RAM was conducted to assess potential metrics, algorithms, and procedures. This paper presents results from initial tests for the development of RAM technology and highlights some of the unique features of RAM applied toa conventional configuration during a ground-based, static, wind-tunnel test.

Patrick C Murphy↗
NASA NTRS2020

Aerodynamic Parameter Estimation Using Reconstructed Turbulence Measurements

A classical method for reconstructing atmospheric turbulence from onboard measurements of airdata and inertial sensors was improved and implemented for real-time computation. The reconstructed turbulence measurements were then included in a system identification analysis to estimate nondimensional stability and control derivatives in a longitudinal short period model using the maximum likelihood equation-error method in the frequency domain with Fourier-transform data. Flight test results using a subscale transport-type airplane showed that the power spectra for the reconstructed vertical gusts resembled the von Kármán turbulence model. Flight data in moderate and severe turbulence exhibited a decorrelation of the modeling data that increased the accuracy of parameter estimation results using the reconstructed turbulence. In particular, pitch rate and angle-of-attack rate derivatives could both be identified from flight data about straight and level flight without special maneuvers or prior information.

Jared A Grauer↗
NASA NTRSDate not supplied

Real-Time State Estimation of Structural Modes for an Aeroelastic Wind Tunnel Model

A method is presented for estimating displacements, velocities, and accelerations of structural modes in generalized coordinates from measured sensor data in real time. Specifically, strain data from conventional strain gauges and fiber optic strain sensors (FOSS) were combined with the strain modes (obtained from a finite element model) in a least-squares estimator to produce structural mode displacement estimates and uncertainties. Likewise, accelerometer data were combined with displacement mode shapes in a second least-squares estimator to produce structural mode acceleration estimates. A Kalman filter was then used to refine the displacement estimates and obtain velocity estimates. The method was applied to the half-span wind tunnel test article used in the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project. The technique was found to be useful for real-time control and system identification applications.

Jared A. Grauer↗
NASA NTRSDate not supplied

Investigation of Longitudinal Aero-Propulsive Interactions of a Small Quadrotor Unmanned Aircraft System

Aerodynamic propulsive and airframe interactions significantly influence the forces and moments of multirotor vehicles. This paper presents recent results studying the influence of these effects on a small quadrotor vehicle in hover and forward flight. Aerodynamic interaction model development was explored utilizing system identification tools and incorporated into a previously developed NASA quadrotor flight dynamic simulation. The aerodynamic interaction model improved accuracy of the simulation in comparison to free-flight and static wind tunnel results. Comparisons between models of different fidelity were completed to demonstrate the effects of aerodynamic interaction on model accuracy and provide recommendations for modelling requirements.

George Altamirano↗
NASA NTRSDate not supplied

Permanent Magnetic Synchronous Motor (PMSM) Model Development

The Advanced Air Transport Technology (AATT) Project seeks to enhance the capabilities of fixed-wing subsonic transport through improved energy efficiency and environmental compatibility. One element of this effort is the use of high efficiency PMSM systems. Understanding the behavior and limitations of the se motors allows the National Aeronautics and Space Administration (NASA) to collaborate with and inform its partners worldwide. PMSM modeling is achieved using MATLAB®-Simulink® (The Math Works, Inc., Natick, Massachusetts). Through the analysis of an existing high-fidelity NASA Electrical Aircraft Testbed (NEAT) model, simplified models of varying fidelity can be developed with the goal of building a PMSM model capable of running in real-time for use in a piloted simulation environment. By utilizing system identification methods, it has been demonstrated that internal electrical components like the inverter can be represented by a simple variable gain thus greatly reducing the required simulation step size and subsequently decreasing model run-time by multiple orders of magnitude

motor controls↗