Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Estimation of post-burst vibration-induced fuel dispersal thresholds following LOCA-simulant testing

The nuclear industry intends to increase burnup past the regulatory limit of 62 GWd/MTU, and to be successful, the dispersal behavior of fragmented high-burnup fuel during loss-of-coolant accidents must be better understood. Part of this behavior is fuel fragmentation, relocation, and dispersal. This work reports on testing concerning the dispersal of fuel from rods following burst and pressure blowdown through the burst. The Fuel Relocation Induced by Accident Recovery (FRIAR) system was used to examine surrogate material and pre-burst cladding specimens to evaluate the effects of vibrational loading, mixture composition, and burst size on post-burst dispersal. Vibrational loading resulted in maximum dispersal around 15 Hz when the loading was performed with peak-to-peak oscillation amplitudes at 0.5 and 1 mm. Here, under this aggressive vibrational loading, dispersal was found to become significant as burst widths increased to approximately 5 mm and larger. However, below 4 mm widths, little material dispersed out of the opening, even at 1 mm amplitudes and for more dispersive mixtures (smaller average fragments). At and above 7 mm widths, dispersal was rapid for all mixtures. Finally, dispersal in the threshold region (4–5 mm wide bursts) strongly depended on the mixture. For mixtures with large fragments, dispersal was minimized to a few fragments, as the large fragments proved to be effective at minimizing dispersal. Conversely, mixtures with smaller fragments showed increased dispersal in this region.

Burst geometry↗
DOE OSTI2023

Multiphysics analysis of fuel fragmentation, relocation, and dispersal susceptibility–Part 3: Thermal hydraulic evaluation of large break LOCA under high-burnup conditions

Increasing the peak rod average burnup of pressurized water reactor (PWR) fuel beyond 62 GWd/tU may increase fuel fragmentation, relocation, and dispersal (FFRD) susceptibility during a large break loss of coolant accident (LBLOCA). TRACE thermal hydraulic (TH) LBLOCA analyses were performed for a realistic 24-month high-burnup PWR equilibrium cycle, to inform subsequent transient BISON high-burnup FFRD susceptibility evaluations. Realistic LBLOCA systems behavior was first established by configuring to and comparing with the BEMUSE OECD LBLOCA benchmark. Fuel and operating conditions were then applied from high-burnup VERA depletion calculations. LBLOCA simulations were performed for 281 selected high-burnup rods, for which transient TH boundary conditions were collected for later use in BISON. The TRACE results indicated that rod linear heat rate (rather than burnup) is the main predictor of peak cladding temperature (PCT) during the event. PCT typically occurred at a local burnup lower than the rod-average burnup, especially for twice-burned fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Loss-of-Coolant Accident Analysis of a High-Burnup Pressurized Water Reactor Core Design Using Gadolinia-Doped UO 2

High-burnup and extended enrichment fuels are of interest for extending the cycle lengths of pressurized water reactors from 18 to 24 months. Changes to the fuel design and core loading scheme have potentially significant safety implications due to power distribution effects, reduced thermal conductivity, and/or increased plenum pressures due to additional burnable poison loadings. Additionally, higher burnups result in increased material degradation and risk of fuel fragmentation, relocation, and dispersal (FFRD). A representative 24-month core design using gadolinia-doped UO 2 was analyzed for performance under large-break (LB) loss-of-coolant accident (LOCA) conditions using PARCS, RELAP5-3D, and BISON. Furthermore, all considered acceptance criteria were met, with no cases exceeding the 1477 K maximum cladding temperature or the post-quench ductility oxidation limit of 17% equivalent cladding reacted. Full-core FFRD susceptibility was estimated to be approximately 455 kg, though high uncertainties exist with current approaches for computing susceptibility. Undoped fuel rods are more likely to be limiting due to higher linear heat rates. Relatively high burnup and linear heat rate rods located in second batch assemblies are of greatest safety significance during LB LOCA for this high-burnup core design.

High burnup↗
DOE OSTI2021

Hydrogen and its detection in fusion and fission nuclear materials – a review

We report fusion and fission reactions are profoundly dependent on hydrogen for sustained reactions. Fusion is fueled by the isotopes of hydrogen, and predominantly hydrogen-based moderators slow fission neutrons to propagate chain reactions. Intentional tritium production in fusion and concomitant tritium production in fission reactors introduce challenges. The technology to efficiently extract, harvest, and quantify tritium in and from advanced fission molten salt coolants and fusion molten tritium breeder materials will require more pronounced research and development. Measuring and quantifying hydrogen is necessary in all areas of nuclear materials. Although many characterization techniques cannot directly detect hydrogen, numerous techniques provide the necessary information to understand the behavior of hydrogen in nuclear materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Evaluation of Thermal Neutron Scattering Cross Section of Uranium Silicide with Ab Initio Lattice Dynamics

Uranium silicide (U 3 Si 2 ) is a candidate material for the high-density nuclear fuel in commercial light water reactors [1], [2]. Its higher uranium density, 11.3 g-U/cm3, compared to that of uranium dioxide (UO 2 ), 9.7 g-U/cm3, can improve the performance of a nuclear reactor while using low enriched uranium (LEU) and diversify the choice of cladding materials [1]–[3]. It also has a higher thermal conductivity than UO 2 , which can reduce the thermal stress on the material caused by a temperature gradient across the fuel pellet and provide a larger margin for some postulated accidents [1], [2], [4]. Furthermore, compared to U3Si, another high-density fuel candidate, it has better resistance to in-pile swelling due to less irradiation-induced rapid amorphization [1], [3]. Corresponding to its importance in nuclear engineering, many previous studies have reported the properties of U3Si2. Experiments showed that U 3 Si 2 is a paramagnetic (PM) metal, where a slight linear increase in magnetic susceptibility was measured with increasing temperature [5], [6]. In addition, thermodynamic quantities such as thermal expansion coefficient, heat capacity, and thermal conductivity were experimentally determined over a wide temperature range [1], [7], [8]. In several computational studies, ab initio atomistic simulations based on density functional theory (DFT) were performed to calculate various properties including elastic constants, electronic density of states (DOS), and phonon dispersion curves [9]–[12]. Nevertheless, thermal neutron scattering cross sections, which are critical to the prediction of the parameters in reactor physics that are ultimately related to reactor criticality, have not yet been evaluated for U3Si2. The scattering cross section can be calculated from the phonon DOS, or the energy spectrum of lattice vibrations, of the crystalline system [13], [14]. However, there is also no experimental data available for the phonon DOS of U 3 Si 2 . While some computational studies reported the phonon DOS and/or dispersion curves from ab initio simulations [9]–[12], the accuracy cannot be guaranteed because it is unclear whether the spin-polarization behavior of PM U 3 Si 2 was properly described. In the present study, the thermal neutron scattering cross section for U 3 Si 2 is evaluated for the first time by calculating the phonon DOS for U3Si2 from ab initio lattice dynamics (AILD) simulations based on DFT. First, U 3 Si 2 is modeled based on the experimental structure, and AILD simulations are performed on the modeled U3Si2 to optimize the structure. Next, AILD simulations are performed for supercells with atomic displacement to calculate Hellmann-Feynman forces. Based on the calculated forces, partial phonon DOSs for U and Si are obtained, and the thermal neutron scattering law (TSL) for U 3 Si 2 is finally evaluated. To verify the accuracy of the calculations in the present study, the calculation results are compared with experimental data on the structure and heat capacity of U3Si2 [1], [7], [8], [15].

Geometry Optimization↗
DOE OSTI2023

Diffusion in undoped and Cr-doped amorphous UO 2

UO 2 fuel pellets are often doped with chromium oxide to obtain favourable properties such as higher density, improved thermal stability, large grain sizes, improved pellet-clad interaction margins, and increased fission gas retention during transients. Chromium has a low solubility limit in UO 2 , with past experimental work reporting solubility limits ranging between 0.004 to 0.06 wt.% Cr. Due to its low solubility, segregation of Cr ions to the grain boundary may occur. Further, the complexity of these boundaries may be high as observed in other ceramics resulting in disordered or amorphous regions along the boundary, affecting a range of material and operational properties of the fuel pellet. To assess these disordered regions, in this work we study amorphous undoped and Cr doped UO 2 systems (containing 10–50 at.% Cr 3+ ) that have been modelled using classical molecular dynamics methods incorporating Cr 3+ into the well-used CRG potential library. Diffusion coefficients, pre-exponential factors, and activation energies for diffusion were computed for oxygen ions, assessing the impact of structure and extrinsic species on migration. Oxygen diffusion was observed to be much faster in the undoped amorphous system compared to its crystalline counterpart. Oxygen diffusion in doped systems decreased with increasing Cr concentration, highlighting the importance of additives to retain fission products and other migratory species.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Hydriding, Oxidation, and Ductility Evaluation of Cr-Coated Zircaloy-4 Tubing

Accident-tolerant fuel concepts have been developed recently in diverse research programs. Recent research has shown clear advantages of Cr-coated Zr cladding over bare cladding tubes regarding oxidation behavior under the design basis loss-of-coolant accident condition. However, limited data are available about the hydriding behavior of the Cr coating. For that purpose, Cr-coated Zricaloy-4 tubes were tested to investigate the effects of hydriding, oxidation, and postquench ductility behavior on coated Zr cladding. A high-power impulse magnetron sputtering (HiPIMS) process was used to produce a high-density coating on the Zircaloy-4 tube surface. Coated and uncoated Zircaloy-4 tube specimens underwent one-sided hydriding in a tube furnace filled with pure hydrogen gas at 425 °C. The tubing specimen ends were sealed with Swagelok plugs before the hydriding runs. For uncoated specimens, H analysis of the hydrided specimens indicated that the H content increased as the test time and initial pressure increased. However, almost no change was observed for the coated specimens that were hydrided under the same test conditions. After one-sided hydriding, the hydrided coated and uncoated specimens were exposed to steam at high temperatures for two-sided oxidation studies to simulate accident conditions. The coated specimens showed a slower oxidation: oxygen pickup was 50% lower than the uncoated specimens tested under the same conditions. Ring compression testing was performed to evaluate the embrittlement behavior of the Cr-coated specimens after hydriding and oxidation. The results indicated that the HiPIMS coating provides excellent protection from hydriding and oxidation at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Conceptual Neutronics Scoping for Ramp Testing in the Advanced Test Reactor

With the closer of the Halden Boiling Water Reactor in 2018, the global capacity for in-reactor power ramp testing has been lost. As such tests provide valuable data for understanding pellet-cladding interaction (PCI) phenomena, finding new facilities for ramp testing is of interest to the United States Accident-Tolerant Fuel (ATF) Program. Several options at Idaho National Laboratory (INL) are being evaluated for adding ramp test capabilities. In the Transient Reactor Test Facility (TREAT), one option is testing inside a Transient Water Irradiation System in TREAT (TWIST) capsule. In the Advanced Test Reactor (ATR), one option under consideration is testing in an I-Loop toward the outer edge of the core. Another is testing in Loop-2A, located in the Center Flux Trap (CFT) of the ATR. In this paper, we examine the conceptual scoping for the Loop-2A experiment known as ATF-2Ramp.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Overview of a Versatile Loading System for Anisotropic Material Property Characterization

Additive manufacturing, cold rolling, and other thermomechanical treatments on metals, especially HCP, can cause texture and oriented grain structures resulting in anisotropic mechanical properties. This can lead to macroscopic response that significantly deviates from isotropic assumptions which motivates studying mechanical properties in multiple directions. In addition, multiaxial loading and complex stress states overlapping the above mentioned material anisotropy can lead to unexpected outcomes. Idaho National Laboratory developed an advanced mechanical testing system to study a range of uniaxial to multiaxial stress states while measuring the anisotropic response bringing insight into the overlap between material properties and stress states. High-temperature capability and stress- or strain-controlled loading is available to enable a variety of experiment types and conditions to measure elastic, plastic, and viscoplastic properties. This poster presents the design and capabilities of this system with preliminary results highlighting the benefits of multiaxial loading and anisotropic analysis in an integrated system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Conceptual Neutronics Scoping for Ramp Testing in the Advanced Test Reactor

With the closure of the Halden Boiling Water Reactor in 2018, the global capacity for in-reactor power ramp testing has been lost. As such tests provide valuable data for understanding pellet-cladding interaction (PCI) phenomena, finding new facilities for ramp testing is of interest to the United States Accident-Tolerant Fuel (ATF) Program. Several options at Idaho National Laboratory (INL) are being evaluated for adding ramp test capabilities. In the Transient Reactor Test Facility (TREAT), one option is testing inside a Transient Water Irradiation System in TREAT (TWIST) capsule. In the Advanced Test Reactor (ATR), one option under consideration is testing in an I-Loop toward the outer edge of the core. Another is testing in Loop-2A, located in the Center Flux Trap (CFT) of the ATR. In this paper, we examine the conceptual scoping for the Loop-2A experiment known as ATF-2Ramp.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Pellet cladding mechanical interaction as a potential failure mechanism during a control rod drop accident in a boiling water reactor

Boiling water reactors (BWRs) represent approximately one-third of the operating fleet in the United States, contributing significantly towards the global effort in reducing carbon emissions. Even though most of the operating fleet has been in operation for quite some time, continued advancements in new nuclear fuel (such as accident tolerant fuel) or operating regimes (such as power up-rates and higher burnup operation) necessitates similar advancements in modeling and simulation capabilities. Bison, a component of the Virtual Environment for Reactor Applications (VERA), is a high-fidelity fuel performance code able to explore the fuel performance of a wide variety of fuel types in one-, two-, and three-dimensions. Until recently, the code had not been used for analyses of BWRs. Modeling capabilities have been added for Gd-bearing UO{sub 2} and pure zirconium liners. New models have been added based upon the U.S. Nuclear Regulatory Commission (NRC) guide-lines for hydrogen pickup in Zircaloy-2 claddings and pellet-clad mechanical interaction (PCMI) failure during a reactivity insertion accident (RIA), known as a rod drop accident (CRDA) in BWRs. Implementing and/or improving Bison modeling capabilities extended its analytical reach to areas beyond its original intended purpose. This paper demonstrates one of these capabilities as a proof of concept. Recently developed models enable Bison to provide an alternate approach for cladding integrity determination in CRDA evaluations, which currently use bounding conservative estimates. As part of this demonstration, NRC guidance on hydrogen-pickup and PCMI failure models were utilized in this research. Even though more research is needed in establishing right inputs and process in this area, this paper demonstrates Bison's ability to determine cladding integrity in a CRDA evaluation. This first of a kind demonstration is a proof of concept in this area, which could potentially be extended to a number of other areas where a more accurate cladding integrity determination would be needed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Specifications of FIPD Fission Gas Release Data

All fission gas release data stored in the Fuels Irradiation & Physics Database (FIPD) was originally measured using the Gas Assay, Sample and Recharge (GASR) System in the Hot Fuel Examination Facility (HFEF). It is therefore called GASR data in FIPD. During the measurement of a sample, such as an irradiated EBR-II fuel element/capsule, a pinhole-sized region near the top of the element plenum was melted by a laser. Plenum gas then expanded into a calibrated volume (note: in this document, “sample” and “capsule/element” are used interchangeably consistent with GASR documents in FIPD). The pressure rise in the volume was recorded. Helium backfilling and expansion was then performed to determine the sample (e.g., fuel element plenum) volume using Boyle’s Law and assuming ideal gas behavior at constant temperature. With the plenum volume and the recorded pressure rise, the sample (e.g., fuel element plenum) pressure was derived with assumption of ideal gas law behavior. The plenum volume and pressure as well as the cladding temperature during the measurement were collected (GASR data in FIPD). Other records associated with the fission gas release data include: raw GASR data records including volumes and post-puncture pressures of seal head/sealing head and manifold, calibration data, backfilling gas pressure data, and the data analysis records. A sample(s) of the fission gas released from the plenum was collected by the GASR system into sample bottles. The chemical and isotopic composition of the gas sample was analyzed separately from GASR data, and will be discussed in a separate specification. The plenum volume, pressure, and cladding temperature during the measurement are typically utilized to determine the number of moles of gas in the plenum. This quantity is often compared to the number of moles of gas generated by fission events. However, calculating these values and their associated uncertainty is beyond the scope of this document, as it necessitates additional assumptions. The most important document to understand the FIPD fission gas data is the GASR operational manual (title: Gas Assay, Sample and Recharge System (GASR) operation and maintenance manual, HFEF/N OMM 4381, DOC. NO. W0018-0032-ES-00). This manual provides: (1) description of the GASR and the functions of each component (laser drilling, welding, seal head/sealing head, manifold, vacuum system, sample system, purge and gas tag system, etc.); (2) step-by-step guidance on calibrations, operations, and measurements; and (3) maintenance procedures and other details relating to the structure and operation of the GASR. Note that the original GASR operated until 2020. A new GASR with the same design and measurement methodology was installed in 2021. The specifications of the GASR presented on the HFEF website at this time are consistent with the ones given in the operational manual. The methods to calculate the plenum volume and pressures were not included in the operational manual, but were recorded in the legacy data analysis files. Details of the methods are given in Chapter 3.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

FY21 burst activities with coated Zircaloy-4 under accident conditions

This report summarizes the results of Advanced Fuels Campaign (AFC) accident-tolerant fuel (ATF) burst activities. Nuclear service grade Zry-4 was procured and coated with a 7-micron thick Cr coating. The coating quality was investigated, and there were several defects at the Cr/Zry-4 interface due to the surface roughness of the as received Zry-4 tubing. To provide insight into the effect of coating defects on the cladding performance under accident scenarios, the unirradiated uncoated and coated material was tested under loss of coolant accident (LOCA) and pellet cladding mechanical interaction (PCMI) reactivity insertion accident (RIA) conditions. The defected coating appeared to have no impact on the cladding performance under these scenarios when compared to the as-received cladding material.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Tensile properties of the neutron irradiated HT-9 ACO-3 duct

HT-9, a ferritic-Martensitic steel, has attracted significant interest as a structural and cladding material for a variety of high dose nuclear component applications. This study examines the tensile properties of a HT-9 fuel assembly duct from the fast flux test facility, FFTF. The duct, from the Advanced Core Oxide-3 (ACO-3) irradiation test, was subjected to fast neutron irradiation exposure ranging from 3 dpa above the core top to nearly 155 dpa near the core mid-plane, spanning a temperature range from 382 °C at the lower end to 504 °C at the top. Due to the combination of thermal and neutron flux gradients along the core height. This yields a variety of irradiation damage processes which depend on core location. Tensile properties of specimens extracted at different positions along the height of the irradiated duct were measured at 25 °C, 200 °C and near their in-core irradiation temperature. The results show temperature has a greater impact than dose on post-irradiation strength and ductility. Two irradiation temperature regimes were determined, below irradiation temperatures of 420 °C irradiation hardening increases as irradiation temperature decreases, and above that temperature relatively minor changes are observed in tensile properties. These results are discussed in terms of expected microstructural changes, indicating that dislocation content is a strong contributor in these findings.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Long-Length SiC/SiC Tube Irradiation Experiment at LWR Temperatures Inserted into HFIR

This report describes the pre-irradiation characterization and successful assembly of a High Flux Isotope Reactor (HFIR) irradiation experiment designed to assess radiation-induced lateral bowing of silicon carbide fiber–reinforced, silicon carbide matrix composite (SiC/SiC) components under a radial fast neutron flux gradient at representative light-water reactor (LWR) temperatures of approximately 300 °C. The over-arching goal of this work is to validate thermomechanical models of SiC/SiC composite fuel assembly distortion used to predict the extent of lateral bowing and dose at which bowing reaches a maximum value. Ultimately, these models are used to ensure that fuel assembly distortion does not block coolant channels, interfere with control rod/blade movements, and/or impact local reactivity. The experiment contains six cladding tube specimens that are approximately 558.5 mm long with representative pressurized water reactor (PWR) outer and inner diameters of 9.5 mm and 7.5 mm, respectively. The specimens were thoroughly characterized prior to irradiation using traditional dimensional inspection and surface profilometry so that these measurements can later be compared with similar measurements that will be made post-irradiation to determine radiation-induced deformations. Furthermore, fine engraving markers were inscribed along the outer surfaces of the specimen and mapped using analytic photography and a three-dimensional stage. This technique allowed for accurate measurements of the marker spacings, which can be compared with similar measurements that will be made post-irradiation to provide local radiation-induced strain mapping. A light curtain optical micrometer was also employed to measure the pre-irradiation bowing of each specimen. The experiment was successfully assembled and inserted into position VXF-19 for HFIR cycle 516, which began May 12, 2026. The experiment will be removed after cycle 519, which is currently scheduled to end in December 2026.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

International fuel performance study of fresh fuel experiments for PCMI effects during RIA experiments

This paper presents the results of High-burnup Experiments for Reactivity-initiated Accident (HERA) Modeling & Simulation (M&S) exercise. The HERA project under the Nuclear Energy Agency (NEA) Second Framework for Irradiation Experiments (FIDES-II) program is focused on studying Light Water Reactor (LWR) fuel behavior during Reactivity-Initiated Accident (RIA) conditions. The Part I M&S cases are based on a series of tests in the Transient Reactor Test (TREAT) facility in the United States and the Nuclear Safety Research Reactor (NSRR) in Japan. The purpose of this work is to evaluate the test design to accomplish its goals in establishing clearer understanding of the effects of power pulse width during RIA conditions. Further, the blind predictions using various computational tools have been performed and compared amongst to interpret the behaviors of high burnup fuels during RIA. While many international participants evaluate the thermal–mechanical behavior of fuel rod under different conditions, a considerable scatter of outputs comes out for the cases due to the disparity between codes in predicting mechanical behaviors. In general, however, the results of thermal–mechanical analysis elaborate that nominal design conditions the shorter pulse width tests in NSRR should cause cladding failures while the TREAT tests appear to have more split prediction of failure or not. Furthermore, the sensitivity analysis varying key testing parameters reveals the considerable effect of power pulse width and total energy deposition on prediction of fuel rod failure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A LOCA Analysis Tool: Coupling RELAP5-3D to BISON

Experimental evidence illustrates that at burnups slightly above the current regulatory limit of a rod-averaged burnup of 62 MWd/kgU, the ceramic UO 2 inside light-water reactor fuel rods becomes susceptible to a phenomenon known as fuel fragmentation, relocation, and dispersal (FFRD) during a loss of coolant accident (LOCA) transient. The severity of FFRD is strongly influenced by the zirconium-based (Zircaloy) cladding behavior during the LOCA transient. A Technology Commercialization Fund (TCF) project was awarded to an Electric Power Research Institute (EPRI)/Idaho National Laboratory team to create a LOCA analysis tool that couples BISON to the systems/thermal-hydraulics code RELAP5-3D [1] for analysis of LOCA scenarios. In addition, further refinements to existing BISON models were identified as necessary to more accurately represent more recent experimental evidence from the Studsvik Cladding Integrity Project (SCIP) and other experimental programs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗