Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Boundary-layer effects in composite laminates. I - Free-edge stress singularities. II - Free-edge stress solutions and basic characteristics

The fundamental nature of the boundary-layer effect in fiber-reinforced composite laminates is formulated in terms of the theory of anisotropic elasticity. The basic structure of the boundary-layer field solution is obtained by using Lekhnitskii's stress potentials (1963). The boundary-layer stress field is found to be singular at composite laminate edges, and the exact order or strength of the boundary layer stress singularity is determined using an eigenfunction expansion method. A complete solution to the boundary-layer problem is then derived, and the convergence and accuracy of the solution are analyzed, comparing results with existing approximate numerical solutions. The solution method is demonstrated for a symmetric graphite-epoxy composite.

Wang, S. S.↗
NASA NTRS1980

Effect of load, area of contact, and contact stress on the wear mechanisms of a bonded solid lubricant film

A pin on disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically tipped riders. Different projected contact stresses were obtained by applying loads of 2.5- to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build up of thick rider transfer films.

Fusaro, R. L.↗
NASA NTRS1987

Thermally induced stresses and deformations in angle-ply composite tubes

Cure-induced uniform temperature change effects on the stresses, axial expansion, and thermally-induced twist of four specific angle-ply tube designs are discussed with a view to the tubes' use as major space structure components. The stresses and deformations in the tubes are studied as a function of the four designs, the off-axis angle, and the single-material and hybrid reinforcing-material construction used. It is found that tube design has a minor influence on the stresses, axial stiffness, and axial thermal expansion characteristics, which are more directly a function of off-axis angle and material selection; tube design is, however, the primary influence in the definition of thermally-induced twist and torsional stiffness characteristics. None of the designs is free of thermally induced twist.

Hyer, M. W.↗
NASA NTRS1981

Effect of load, area of contact, and contact stress on the tribological properties of polyimide bonded graphite fluoride films

A pin-on-disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide-bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically-tipped riders. Different projected contact stresses were obtained by applying loads of 2.5-to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build-up of thick rider transfer films.

Fusaro, R. L.↗
NASA NTRS1954

Charts relating the compressive buckling stress of longitudinally supported plates to the effective deflectional and rotational stiffness of the supports

A stability analysis is made of a long flat rectangular plate subjected to a uniform longitudinal compressive stress and supported along its longitudinal edges and along one or more longitudinal lines by elastic line supports. The elastic supports possess deflectional and rotational stiffness. Such configuration is an idealization of the compression cover skin and internal structure of a wing and tail surfaces. The results of the analysis are presented in the form of charts in which the buckling-stress coefficient is plotted against the buckle length of the plate for a wide range of support stiffnesses. The charts make possible the determination of the compressive buckling stress of plates supported by members whose stiffness may or may not be defined by elementary beam bending and twisting theory but yet whose effective restraint is amenable to evaluation. The deflectional and rotational stiffness provided by longitudinal stiffeners and full-depth webs is discussed and numerical examples are given to illustrate the application of the charts to the design of wing structures.

Anderson, Roger A↗
DOE OSTI2023

Preliminary prediction of long-term aging and creep behavior of AM 316 SS

This report describes the development of initial mechanism models for the long term behavior of additively manufactured (AM), laser powder-bed fusion 316H stainless steel under the conditions expected in future advanced nuclear reactors. These models focus on key features of the material microstructure and response that differ from the conventionally-manufactured wrought material. Specifically, the report describes the development of models to capture the unique response of the AM material focusing on irradiation creep and swelling, the effect of internal stress, for example caused by dislocation structure, on precipitation, and the effect of the AM grain and dislocation structure on the macroscale creep and thermal aging behavior. This single mechanism models represent progress towards a complete, physics-based model for the long-term material behavior as well as elucidate key differences in the AM material behavior, when compared to the better-understood, conventionally-manufactured 316H.

36 MATERIALS SCIENCE↗
NASA NTRS1966

Thermal stress-relief treatments for 2219 aluminum alloy are evaluated

Evaluation of three thermal stress relief treatments for 2219 aluminum alloy in terms of their effect on residual stress, mechanical properties, and stress corrosion resistance. The treatments are post aging and stress relieving fullscale and subscale parts formed in the aged T81 condition, and aging subscale parts formed in the unaged T31 condition.

Source record↗
NASA NTRS1980

Phase 2 of the array automated assembly task for the low cost silicon solar array project

Studies were conducted on several fundamental aspects of electroless nickel/solder metallization for silicon solar cells. A process, which precedes the electroless nickel plating with several steps of palladium plating and heat treatment, was compared directly with single step electroless nickel plating. Work was directed toward answering specific questions concerning the effect of silicon surface oxide on nickel plating, effects of thermal stresses on the metallization, sintering of nickel plated on silicon, and effects of exposure to the plating solution on solar cell characteristics. The process was found to be extremely lengthy and cumbersome, and was also found to produce a product virtually identical to that produced by single step electroless nickel plating, as shown by adhesion tests and electrical characteristics of cells under illumination.

Petersen, R. C.↗
NASA NTRS1992

Polarized-Cathodoluminescence Study Of Stress In GaAs/Si

Report describes experiments in which linearly polarized cathodoluminesce scanning electron microscopy, in both imaging and spectroscopic forms, used to analyze spatial variations in stress tensors in specimens of GaAs/Si. Specimens fabricated by atmospheric-pressure metallo-organic chemical vapor deposition of GaAs to thickness of 4 micrometers on Si substrates. Combination of mismatch between Si and GaAs crystal lattices and differential thermal contraction of materials from deposition temperature (700 degrees C) to room temperature gives rise to stresses in GaAs layer. Experiments conducted to contribute to understanding of effects of these stresses and ramifications thereof for fabrication of electronic devices in GaAs/Si system.

Rich, Daniel H.↗
NASA NTRS1996

Investigation of Thermal Stress Convection in Nonisothermal Gases Under Microgravity Conditions

Microgravity conditions offer an environment in which convection in a nonisothermal gas could be driven primarily by thermal stress. A direct examination of thermal stress flows would be invaluable in assessing the accuracy of the Burnett terms in the fluid stress tensor. We present a preliminary numerical investigation of the competing effects of thermal stress, thermal creep at the side walls, and buoyancy on gas convection in nonuniformly heated containers under normal and reduced gravity levels. Conditions in which thermal stress convection becomes dominant are identified, and issues regarding the experimental measurement of the flows are discussed.

Mackowski, Daniel W.↗
NASA NTRSDate not supplied

Effect of Boundary Conditions on Process-Induced Stresses in a Plain Weave Unit Cell

Woven polymer matrix composites (PMCs) are leveraged in aerospace applications for their desirable specific properties, yet they are vulnerable to high residual stresses during manufacturing and their complex geometry makes experimental results difficult to observe. Process modeling is needed to characterize the effects of the curing and predict end stress states. Finite element software can be used to model woven architectures, however accurate representation of processing conditions remains a challenge when it comes to selecting boundary conditions. The effect of BCs on process-induced stress within woven PMCs is studied. The commercial Finite Element Analysis (FEA) software Abaqus is coupled with user-written subroutines in a process modeling framework. A two-dimensionally (2D) woven PMC repeating unit cell (RUC) is modeled with TexGen and Abaqus. Virtual curing is imposed on the bulk matrix. The BC study is conducted with Free, Periodic, Flat, and Flat-Free configurations. Results show that the end stress state is sensitive to the boundary condition assumptions. Flat BC results show great agreement with Periodic BCs. Residual stress results from process modeling are then compared with a linear-elastic thermal cooldown analysis in Abaqus. Cooldown results indicate an overestimation in matrix stresses compared with process modeling.

micromechanics↗
NASA NTRS1994

Plasmodesmal-mediated cell-to-cell transport in wheat roots is modulated by anaerobic stress

Cell-to-cell transport of small molecules and ions occurs in plants through plasmodesmata. Plant roots are frequently subjected to localized anaerobic stress, with a resultant decrease in ATP. In order to determine the effect of this stress on plasmodesmal transport, fluorescent dyes of increasing molecular weight (0.46 to 1OkDa) were injected into epidermal and cortical cells of 3-day-old wheat roots, and their movement into neighboring cells was determined by fluorescence microscopy. Anaerobiosis was generated by N2 gas or simulated by the presence of sodium azide, both of which reduced the ATP levels in the tissue by over 80%. In the absence of such stress, the upper limit for movement, or size exclusion limit (SEL), of cortical plasmodesmata was <1 kDa. The ATP analogue TNP-ADP (mw 681) moved across the plasmodesmata of unstressed roots, indicating that plasmodesmata may be conduits for nucleotide (ATP and ADP) exchange between cells. Upon imposition of stress, the SEL rose to between 5 and 10 kDa. This response of plasmodesmata to a decrease in the level of ATP suggests that they are constricted by an ATP-dependent process so as to maintain a restricted SEL. When roots are subjected to anaerobic stress, an increase in SEL may permit enhanced delivery of sugars to the affected cells of the root where anaerobic respiration could regenerate the needed ATP.

NASA Discipline Plant Biology↗
NASA NTRS2015

Effect of Notches on Creep-Fatigue Behavior of a P/M Nickel-Based Superalloy

A study was performed to determine and model the effect of high temperature dwells on notched low cycle fatigue (NLCF) and notch stress rupture behavior of a fine grain LSHR powder metallurgy (PM) nickel-based superalloy. It was shown that a 90 second dwell applied at the minimum stress (min dwell) was considerably more detrimental to the NLCF lives than similar dwell applied at the maximum stress (max dwell). The short min dwell NLCF lives were shown to be caused by growth of small oxide blisters which caused preferential cracking when coupled with high concentrated notch root stresses. The cyclic max dwell notch tests failed mostly by a creep accumulation, not by fatigue, with the crack origin shifting internally to a substantial distance away from the notch root. The classical von Mises plastic flow model was unable to match the experimental results while the hydrostatic stress profile generated using the Drucker-Prager plasticity flow model was consistent with the experimental findings. The max dwell NLCF and notch stress rupture tests exhibited substantial creep notch strengthening. The triaxial Bridgman effective stress parameter was able to account for the notch strengthening by collapsing the notched and uniform gage geometry test data into a singular grouping.

Dwell Notch Fatigue↗
NASA NTRS1984

The effect of thickness on fatigue crack propagation in 7475-T731 aluminum alloy sheet

Tests were conducted on three thicknesses of 7475-T731 aluminum alloy sheet to investigate the effect of thickness on fatigue crack propagation under constant amplitude loading conditions and on retardation following a single peak overload. Constant amplitude loading tests were performed at stress ratios of 0.05 and 0.75 to obtain data for conditions with crack closure and without crack closure, respectively. At both stress ratios a thickness effect was clearly evident, with thicker specimens exhibiting higher growth rates in the transition from plane strain to plane stress region. The effect of thickness for a stress ratio of 0.05 corresponded well with the fracturing mode transitions observed on the specimens. A model based on the strain energy release rate which accounted for the fracture mode transition was found to correlate the thickness effects well. The specimens tested at the stress ratio of 0.75 did not make the transition from tensile mode to shear mode, indicating that another mechanism besides crack closure or fracture mode transition was active.

Daiuto, R. A.↗
DOE OSTI2021

Large response of charge stripes to uniaxial stress in La 1.475 Nd 0.4 Sr 0.125 CuO 4

The La-based "214"cuprates host several symmetry-breaking phases, including superconductivity, charge and spin order in the form of stripes, and a structural orthorhombic-to-tetragonal phase transition. Therefore these materials are an ideal system to study the effects of uniaxial stress onto the various correlations that pervade the cuprate phase diagram. We report resonant x-ray scattering experiments on La 1.475 Nd 0.4 Sr 0.125 CuO 4 (LNSCO-125) that reveal a significant response of charge stripes to uniaxial tensile stress of ~0.1GPa. These effects include a reduction of the onset temperature of stripes by ~50K, a 29-K reduction of the low-temperature orthorhombic-to-tetragonal transition, competition between charge order and superconductivity, and a preference for stripes to form along the direction of applied stress. Altogether, we observe a dramatic response of the electronic properties of LNSCO-125 to a modest amount of uniaxial stress.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗