Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Defect properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Proton radiation effects on electronic defect states in MOCVD-grown (010) β -Ga 2 O 3

The impact of 1.8 MeV proton irradiation on metalorganic chemical vapor deposition grown (010) β-Ga 2 O 3 Schottky diodes is presented. It is found that after a 10.8 × 10 13 cm –2 proton fluence the Schottky barrier height of (1.40 ± 0.05 eV) and the ideality factor of (1.05 ± 0.05 ) are unaffected. Capacitance–voltage extracted net ionized doping curves indicate a carrier removal rate of 268 ± 10 cm –1 . The defect states responsible for the observed carrier removal are studied through a combination of deep level transient and optical spectroscopies (DLTS/DLOS) as well as lighted capacitance–voltage (LCV) measurements. The dominating effect on the defect spectrum is due to the E c -2.0 eV defect state observed in DLOS and LCV. This state accounts for ~75 % of the total trap introduction rate and is the primary source of carrier removal from proton irradiation. Of the DLTS detected states, the E c -0.72 eV state dominated but had a comparably smaller contribution to the trap introduction. These two traps have previously been correlated with acceptor-like gallium vacancy-related defects. Several other trap states at E C -0.36, E C -0.63, and E C -1.09 eV were newly detected after proton irradiation, and two pre-existing states at E C -1.2 and E C -4.4 eV showed a slight increase in concentration after irradiation, together accounting for the remainder of trap introduction. However, a pre-existing trap at E c -0.40 eV was found to be insensitive to proton irradiation and, therefore, is likely of extrinsic origin. Furthermore, the comprehensive defect characterization of 1.8 MeV proton irradiation damage can aid the modeling and design for a range of radiation tolerant devices.

42 ENGINEERING↗
DOE OSTI2020

Nature of native atomic defects in ZrTe 5 and their impact on the low-energy electronic structure

Over the past decades, investigations of the anomalous low-energy electronic properties of ZrTe 5 have reached a wide array of conclusions. An open question is the growth method's impact on the stoichiometry of ZrTe 5 samples, especially given the very small density of states near its chemical potential. In this work, we report on high-resolution scanning tunneling microscopy and spectroscopy measurements performed on samples grown via different methods. Using density functional theory calculations, we identify the most prevalent types of atomic defects on the surface of ZrTe 5 , namely, Te vacancies and intercalated Zr atoms. Finally, we precisely quantify their density and outline their role as ionized defects in the anomalous resistivity of this material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Locally Engineering and Interrogating the Photoelectrochemical Behavior of Defects in Transition Metal Dichalcogenides

Transition metal dichalcogenides (TMDs) are attractive materials for a variety of applications in solar energy conversion and electrocatalysis, due to their favorable optical and electrical properties and their unique two-dimensional structures which facilitate the fabrication of wide-area, ultrathin layers. Unfortunately, the basal planes which make up the majority of these materials are relatively inert, and thus a great deal of effort has been directed to engineering favorable, catalytically active defects into these materials. In this paper, we demonstrate how probe-based electrochemical techniques can be employed as multifunctional tools for locally modifying TMD materials and probing the electrochemical behavior of the resulting defects. Scanning Electrochemical Cell Microscopy (SECCM) was employed to locally anodize exfoliated p-type WSe 2 nanosheets, creating hole-like defects within individual basal planes in a highly controllable fashion. Photoelectrochemical SECCM imaging was then employed to characterize the chemical behavior of these engineered defects, revealing significantly enhanced activity toward the Hydrogen Evolution Reaction (HER). Atomic force microscopy studies are presented which suggest these enhancements result from an increased density of monolayer-high step features within the anodized defects. Analysis of the SECCM data in the context of finite element simulations revealed that these enhancements increased with increasing anodization time, with local kinetic rates over 2 orders of magnitude higher than unaltered basal planes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Structure and disorder resulting in ultralow thermal conductivity in the defect chalcopyrite AgInSnSe 4

Quaternary chalcogenides are attractive for a variety of technological fields of interest due to the diverse physical properties these materials possess. Herein, the structural and thermal properties of the disordered chalcopyrite AgInSnSe 4 are reported revealing a distinct relation between its structure and physical properties. Modeling of the experimental temperature-dependent thermal properties revealed an ultralow thermal conductivity (0.47 Wm -1 K -1 at room temperature) due to lattice anharmonicity, a low speed of sound and a low Debye temperature. Moreover, first principles electronic structure calculations revealed that the Ag-Se tetrahedra within the crystal structure possess relatively weak bonds due to occupied antibonding states from p-d orbital hybridization, which suppress the thermal conductivity. Here, in order to further quantify our findings, we extended our analyses to include comparisons with other ternary and quaternary adamantine materials, all of which possess a fourfold tetrahedral coordination of atoms, in revealing the origin of the thermal properties in AgInSnSe 4 .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fluorescent CQD-Doped Styrene Acrylic Emulsion Coating Film with Enhanced Optical Properties

Styrene acrylic emulsions (SAEs) have emerged as a promising material for water-based coatings. However, they are still limited by their own defects in practical applications, poor weatherability, and degradation of performance at lower or higher temperatures. Here, we introduce a facile approach to producing fluorescent carbon quantum dots (CQDs) from wood processing residues and fabricating fluorescent CQD/SAE coating films via emulsion-casting. The addition of the fluorescent CQDs enhanced the optical performance of the CQD/SAE coating films. The fluorescent CQDs were prepared via a hydrothermal approach and were obtained after heating at 180 °C for 6 h at a reaction concentration of 50 mg/mL. The synthesized CQDs resulted in a high fluorescence, and the CQDs had an average size of 1.63 nm. Various concentrations of the fluorescent CQDs were doped into the SAE coating film, which improved its optical properties. We also characterized and discussed the products and then explored their optical properties. This study presents the potential of fluorescent CQD/SAE coating films for applications in anti-counterfeiting coatings, fluorescent adhesives, and papermaking.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Identifying point defects and ordering in the high-entropy layered oxide Li 1.5 MO 3-δ (M=Mn, Al, Fe, Co, Ni) for energy storage applications

High-entropy layered oxides (HELOs) represent a very promising class of next-generation battery cathodes, combining the well-studied properties of layered cathode materials such as LiCoO 2 with the chemical tunability and stability of high-entropy materials. HELO materials often form particles with complex defects and domain structures, complicating accurate characterization of structure and cation mixing. Understanding disorder and order in HELO materials is necessary for understanding their performance and utility as cathodes. Here we demonstrate the characterization of the HELO Li 1.5 MO 3-δ (M = Mn, Al, Fe, Co, Ni), wherein X-ray powder diffraction, transmission electron microscopy imaging, and electron diffraction patterns are analyzed to reveal the presence of ordering in the HELO, with imaging and diffraction simulation employed to compare experimental results to atomic modeling. Finally, without rigorous characterization at the atomic scale, important features such as defect ordering can be easily overlooked and therefore remain unconsidered when interpreting experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling Nondestructive Defect Detection in Additively Manufactured Metallic Structures for Nuclear Applications

The future of quickly, economically produced metallic nuclear reactor parts with minimal supply-chain dependence lies in Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM): a 3D printing method involving laser melting and net shaping stainless steel and Inconel metallic powder into a solid structure. However, intrinsic features in LPBF frequently leads to the formation of materials defects, such as pores, within 3D printed structures. As safe long-term use in energy applications requires knowledge of all relevant defects before deployment in a reactor, we must develop methods for nondestructive detection of these defects. We are investigating Pulsed Thermal Tomography (PTT), which is a non-contact nondestructive imaging method scalable to arbitrary structure size. Thermal tomography (TT) is a computational method for 3D spatial reconstruction of material thermal effusivity from flash or pulsed thermography temperature data cube. Thermography data cube consists of 2D surface temperature measurements at different times. The objective of the present work is to investigate limits on defect detection in AM metallic structures with PTT. To this effect, we modeled PTT with COMSOL heat transfer computer simulations. We developed a layered media COMSOL simulation consisting of a Stainless Steel 316 (SS316) plate with an internal layer of un-sintered SS316 powder. Thermophysical properties of the powder layer were modeled with equivalent volume mixing model. To account for partial sintering at the boundary of the defect, the transition between solid and powder layers was modeled as a Gaussian. Using data from COMSOL simulations, we reconstructed depth-dependent thermal effusivity, which allowed defect visibility estimation. A series of parametric studies determined that at 1mm depth, 50µm is the smallest detectable defect. In addition, classification of the defects which can lead to early fatigue of the metallic structure in a reactor is briefly discussed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Nanoparticle localization within chiral liquid crystal defect lines and nanoparticle interactions

Self-assembly of colloidal particles into predefined structures is a promising way to design inexpensive manmade materials with advanced macroscopic properties. Doping of nematic liquid crystals (LCs) with nanoparticles has a series of advantages in addressing these grand scientific and engineering challenges. It also provides a very rich soft matter platform for the discovery of unique condensed matter phases. The LC host naturally allows the realization of diverse anisotropic interparticle interactions, enriched by the spontaneous alignment of anisotropic particles due to the boundary conditions of the LC director. Here we demonstrate theoretically and experimentally that the ability of LC media to host topological defect lines can be used as a tool to probe the behavior of individual nanoparticles as well as effective interactions between them. LC defect lines irreversibly trap nanoparticles enabling controlled particle movement along the defect line with the use of a laser tweezer. Minimization of Landau–de Gennes free energy reveals a sensitivity of the ensuing effective nanoparticle interaction to the shape of the particle, surface anchoring strength, and temperature, which determine not only the strength of the interaction but also its repulsive or attractive character. Theoretical results are supported qualitatively by experimental observations. Furthermore, this work may pave the way toward designing controlled linear assemblies as well as one-dimensional crystals of nanoparticles such as gold nanorods or quantum dots with tunable interparticle spacing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Blading Phase–Pure Formamidinium–Alloyed Perovskites for High–Efficiency Solar Cells with Low Photovoltage Deficit and Improved Stability

Currently, blade-coated perovskite solar cells (PSCs) with high power conversion efficiencies (PCEs), i.e. greater than 20%, normally employ methylammonium lead tri-iodide with a sub-optimal bandgap. Alloyed perovskites with formamidinium (FA) cation have narrower bandgap and thus enhance device photocurrent. However, FA-alloyed perovskites show low phase stability and high moisture sensitivity. Here, we report that incorporating 0.83 molar percent organic halide salts (OHs) into the perovskite inks enables phase-pure, highly crystalline FA-alloyed perovskites with extraordinary optoelectronic properties. Here, the OH molecules modulate the crystal growth, enhance the phase stability, passivate ionic defects at the surface and/or grain boundaries, and enhance the moisture stability of the perovskite film. We demonstrate a high efficiency of 22.0% under 1 sun illumination for blade-coated PSCs with an open-circuit voltage of 1.18 V, corresponding to a very small voltage deficit of 0.33 V, and significantly improved operational stability with 96% of the initial efficiency retained under one sun illumination for 500 hours.

14 SOLAR ENERGY↗
DOE OSTI2022

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Superior photodynamic effect of single-walled carbon nanotubes in aprotic media: a kinetic study

It has been confirmed that single-walled carbon nanotubes (SWCNTs) could generate reactive oxygen species in aprotic media by utilizing photon energy. However, the impact of photon irradiation on SWCNTs and the kinetics of the generation process in aprotic media are still unclear, which significantly limits the yield performance. In this work, the kinetics for photodynamic effects has been investigated by performing characterizations on ultraviolet-treated SWCNTs using Raman spectroscopy, conductive atomic force microscope (in-situ), kelvin probe force microscope, and X-ray photoelectron spectroscopy. It is found that ultraviolet-treated SWCNTs are observed to have more defects, lower conductivity, and less surface charge after energy conversion. Starting from the fundamental intrinsic properties of SWCNTs, the kinetics and formation of these changes are thoroughly discussed. It turns out that the dispersion, chirality, and structural integrity of SWCNTs are important for achieving high-performance photodynamic effects, which are validated using several different SWCNTs as well as other carbon nanomaterials. A type of (6,5) s-SWCNTs exhibited the highest energy efficiency among a variety of other carbon nanomaterials. The yield rate is 2.15 mM/h, and the energy consumption is determined to be 2.79 W∙h/mM. This work is expected to help dramatically boost the energy efficiency of the photodynamic effect in aprotic media and pave the way for designing high-performance carbon nanomaterial-based photoinduced devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dielectric-Engineered Monolayer MoS 2 Memtransistors for Brain-Inspired Computing with High Recognition Accuracy

Two-dimensional transition metal dichalcogenides (2D-TMDs)-based memtransistors have emerged as promising candidates for neuromorphic hardware due to their exceptional ability to emulate synaptic behavior. However, many existing 2D-TMDs memtransistors rely on polycrystalline channels with grain boundaries or defects introduced through postgrowth treatments, raising concerns about material integrity and the preservation of intrinsic properties. Here, in this work, we demonstrate a monocrystalline monolayer MoS 2 memtransistor fabricated on a silicon nitride (SiN X ) substrate, achieving a large resistive switching ratio of 10 4 , a dynamic range exceeding 90, along with highly linear and symmetric weight updates, minimal cycle-to-cycle variability, and low device-to-device variability. These attributes are critical for enabling high-performance neuromorphic hardware. Based on experimental data, we further show that these artificial synapses enable a recognition accuracy of more than 97% on the MNIST handwritten digits data set. Our findings present a straightforward approach to realizing 2D-TMDs memtransistors through dielectric engineering, offering a promising platform for next-generation neuromorphic computing systems.

2D TMDs↗
DOE OSTI2024

Determination of electron-hole pair creation energy in Cd 0.9 Zn 0.1 Te 0.98 Se 0.02 quaternary semiconductor for room-temperature gamma-ray detection

We report the first-time measurement of the electron-hole pair (ehp) creation energy (W ehp ) in novel Cd 0.9 Zn 0.1 Te 0.98 Se 0.02 (CZTS) quaternary semiconductor. CZTS in single crystalline form is poised to be the future of large-volume room-temperature gamma-ray detectors due to its excellent compositional homogeneity with highly reduced defects, high-Z (atomic number) constituents, wide bandgap (1.6 eV), and superior charge transport properties. Despite a great deal of study of the material and device properties since its inception, the W ehp in CZTS has not been measured experimentally. Accurate determination of W ehp is essential for calibration of the spectrometer and other theoretical calculations. In this study we have used an absolute calibration approach, which is based on an iterative approach that yields the Wehp as the best-fit parameter. Using a 241 Am alpha emitting radioisotope and a planar CZTS detector, the Wehp in CZTS was calculated to be 4.47 eV. The obtained value has been validated by accurately predicting the peak energy for gamma rays emitted by a 137 Cs source and read by a CZTS detector with different dimensions. The dependences of the calculated W ehp value on the detector dimensions, type of interaction, and effect of charge trapping are also discussed.

42 ENGINEERING↗
DOE OSTI2025

Topological solitons in square-root graphene nanoribbons controlled by electric fields

Conjugational defects, also known as solitons, play an important role in the electronic, magnetic, and optical properties of materials. Understanding solitons can uncover intriguing physics and provide insights for designing quantum materials with tailored band structures and electronic properties. Here we propose a framework to create and control solitons via topological phase transitions in a class of graphene nanoribbons (GNRs) called square-root GNRs, using a transverse electric field. To demonstrate the experimental feasibility, we design and synthesize a representative GNR with a bottom-up approach, with first-principles calculations revealing topological soliton states at the domain wall induced by the electric field. In conclusion, the framework introduced in this work can potentially enable direct manipulation of solitons and provide a platform to study them systematically.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Atomically resolved edges and defects in lead halide perovskites

Although edges and defects constitute only a small fraction of crystalline materials, they exert an outsized impact on a material′s properties. Organic–inorganic halide perovskites are promising next-generation semiconductor materials with superior cost effectiveness and interesting optoelectronic properties. However, clear images of their edges have remained challenging to obtain owing to their extreme sensitivity. Using truly high-speed ultralow-dose four-dimensional scanning transmission electron microscopy with dose fractionation, we perform ptychography at, to our knowledge, the lowest-dose atomic resolution to date, revealing not only the detailed atomic structure of the edges of a halide perovskite but also their structural dynamics. Here, a majority methylammonium (MA) and iodine (I) edge termination is observed in methylammonium lead iodide (MAPbI 3 ), and the damage rate of its edges and internal defects is found to depend on the concentration and type of vacancies present, with a preponderance of I vacancies in particular correlating with higher rates of damage.

4D-STEM↗
DOE OSTI2024

Additive manufacturing of defect-free TiZrNbTa refractory high-entropy alloy with enhanced elastic isotropy via in-situ alloying of elemental powders

Laser powder-bed fusion (L-PBF) additive manufacturing presents ample opportunities to produce net-shape parts. The complex laser-powder interactions result in high cooling rates that often lead to unique microstructures and excellent mechanical properties. Refractory high-entropy alloys show great potential for high-temperature applications but are notoriously difficult to process by additive processes due to their sensitivity to cracking and defects, such as un-melted powders and keyholes. Here, we present a method based on a normalized model-based processing diagram to achieve a nearly defect-free TiZrNbTa alloy via in-situ alloying of elemental powders during L-PBF. Compared to its as-cast counterpart, the as-printed TiZrNbTa exhibits comparable mechanical properties but with enhanced elastic isotropy. This method has good potential for other refractory alloy systems based on in-situ alloying of elemental powders, thereby creating new opportunities to rapidly expand the collection of processable refractory materials via L-PBF.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tuning Chiral Anomaly Signature in a Dirac Semimetal via Fast-Ion Implantation

Cd 3 As 2 is a Dirac semimetal that hosts a chiral anomaly, functioning as a platform to realize energy applications. We use fast-ion implantation to enhance the negative longitudinal magnetoresistance (NLMR)─signature of a chiral anomaly─in Nb-doped Cd 3 As 2 thin films. High-energy ion implantation is used to investigate semiconductors and nuclear materials but is rarely employed to study topological materials. We use electrical transport and transmission electron microscopy to characterize the NLMR and crystallinity of Nb-doped Cd 3 As 2 . We find surface-doped thin films display a maximum NLMR around B = 7 T and bulk-doped thin films display a maximum over B = 9 T─all while maintaining crystallinity. This is more than a 100% relative enhancement of the maximum NLMR compared to pristine Cd 3 As 2 . As a result, our work demonstrates the potential of high-energy ion implantation as a practical route to explore chiralitronic properties in topological semimetals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Nanoscale defect evaluation framework combining real-time transmission electron microscopy and integrated machine learning-particle filter estimation

Observation of dynamic processes by transmission electron microscopy (TEM) is an attractive technique to experimentally analyze materials’ nanoscale phenomena and understand the microstructure-properties relationships in nanoscale. Even if spatial and temporal resolutions of real-time TEM increase significantly, it is still difficult to say that the researchers quantitatively evaluate the dynamic behavior of defects. Images in TEM video are a two-dimensional projection of three-dimensional space phenomena, thus missing information must be existed that makes image’s uniquely accurate interpretation challenging. Therefore, even though they are still a clustering high-dimensional data and can be compressed to two-dimensional, conventional statistical methods for analyzing images may not be powerful enough to track nanoscale behavior by removing various artifacts associated with experiment; and automated and unbiased processing tools for such big-data are becoming mission-critical to discover knowledge about unforeseen behavior. We have developed a method to quantitative image analysis framework to resolve these problems, in which machine learning and particle filter estimation are uniquely combined. The quantitative and automated measurement of the dislocation velocity in an Fe-31Mn-3Al-3Si autunitic steel subjected to the tensile deformation was performed to validate the framework, and an intermittent motion of the dislocations was quantitatively analyzed. The framework is successfully classifying, identifying and tracking nanoscale objects; these are not able to be accurately implemented by the conventional mean-path based analysis.

36 MATERIALS SCIENCE↗