Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Compressed/reconstructed test images for CRAF/Cassini

A set of compressed, then reconstructed, test images submitted to the Comet Rendezvous Asteroid Flyby (CRAF)/Cassini project is presented as part of its evaluation of near lossless high compression algorithms for representing image data. A total of seven test image files were provided by the project. The seven test images were compressed, then reconstructed with high quality (root mean square error of approximately one or two gray levels on an 8 bit gray scale), using discrete cosine transforms or Hadamard transforms and efficient entropy coders. The resulting compression ratios varied from about 2:1 to about 10:1, depending on the activity or randomness in the source image. This was accomplished without any special effort to optimize the quantizer or to introduce special postprocessing to filter the reconstruction errors. A more complete set of measurements, showing the relative performance of the compression algorithms over a wide range of compression ratios and reconstruction errors, shows that additional compression is possible at a small sacrifice in fidelity.

Dolinar, S.↗

Influence of Actuator Movement Rate During Acquisition of Inlet Characterization Data

This report considers using a process to acquire performance data for supersonic mixed-compression inlets that is faster and less costly than the previous process. In the previous process for acquiring data during wind tunnel experiments, actuators for backpressuring an inlet moved in discrete increments, paused for dynamics to dampen, measured data for 5 s, recorded the data, and then reduced the data to graphic plots of pressure recovery versus mass capture ratio. This discrete data acquisition procedure was methodical, reliable, and accurate. However, acquiring data to characterize the inlet consumed significant wind-on time. Wind tunnel operation was costly when considering maintenance, energy, and human resources (operators and research team); therefore, the price for each data point was high. This report presents a quicker method to obtain all measurements, one which can also be used in blowdown wind tunnels. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. The backpressuring actuator moves continuously, and measurements from high-speed pressure sensors are recorded as the actuator progresses to and past the incremental points. Despite its advantages, the approach raised the following questions: (1) Will the new process be as accurate as the previous process? and (2) Are there any hidden costs? These concerns are addressed in this report. This report reviews a study that was undertaken to compare wind tunnel experiment data taken using the previous discrete data acquisition procedure with data recorded using the dynamic inlet characterization data acquisition procedure. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data for analysis are explained, and a discussion of the results is given. Finally, conclusions from this study that may guide further work in this area are presented.

Inlet Characterization Curves↗

A two-equation turbulence model for compressible reacting flows

A two-equation turbulence model (k-epsilon) has been modified to model compressible reacting flows. A compressibility correction model based on modeling the dilatational terms in the Reynolds stress equations has been used. Computations are carried out using the Navier-Stokes solver SPARK which includes a finite rate chemistry model for hydrogen-air combustion. Initially, planar compressible mixing layers are simulated. Comparisons of the predictions with available experimental data and the predictions of a compressible Reynolds stress closure indicate that the model is well suited for the study of such flows. The decrease in the growth rate of the mixing layer with increasing convective Mach number is well predicted. The model is then tested on a three-dimensional supersonic flow problem where solid boundaries are present. An axisymmetric nonreacting mixing layer flow involving dissimilar gases is evaluated next using the model and the predictions are compared with available experimental data. Finally, two reacting turbulent flow configurations have been studied and comparison of predictions and experimental data has been done. The comparisons indicate that the model predicts the overall features of the test cases very well.

Narayan, J. R.↗

Towards Efficient Scientific Data Management Using Cloud Storage

A software prototype allows users to backup and restore data to/from both public and private cloud storage such as Amazon's S3 and NASA's Nebula. Unlike other off-the-shelf tools, this software ensures user data security in the cloud (through encryption), and minimizes users operating costs by using space- and bandwidth-efficient compression and incremental backup. Parallel data processing utilities have also been developed by using massively scalable cloud computing in conjunction with cloud storage. One of the innovations in this software is using modified open source components to work with a private cloud like NASA Nebula. Another innovation is porting the complex backup to- cloud software to embedded Linux, running on the home networking devices, in order to benefit more users.

He, Qiming↗

Boron/aluminum skins for the DC-10 aft pylon

Boron/aluminum pylon boat tail skins were designed and fabricated and installed on the DC-10 aircraft for a 5-year flight service demonstration test. Inspection and tests of the exposed skins will establish the ability of the boron/aluminum composite to withstand long time flight service conditions, which include exposure to high temperatures, sonic fatigue, and flutter. The results of a preliminary testing program yield room temperature and elevated temperature data on the tension, compression, in-plane shear, interlaminar shear, bolt bearing, and tension fatigue properties of the boron/aluminum laminates. Present technology was used in the fabrication of the skins. Although maximum weight saving was not sought, weight of the constant thickness boron/aluminum skin is 26% less than the chemically milled titanium skin.

Elliott, S. Y.↗

Seasat-A - An ocean observation satellite

Mission details, onboard equipment, and measurements to be taken are described for the Seasat-A global ocean monitoring satellite. The satellite is designed for mapping the global ocean geoid, charting ice fields and leads, precision measurement of sea surface topography, global monitoring of wave height and wave directional spectra, surface winds and wind direction, current patterns, and ocean temperature. Data handling subsystems, a compressed pulse radar altimeter, coherent synthetic aperture imaging radar, microwave wind scatterometer, scanning visible/IR radiometer, scanning multispectral (5 freq) microwave radiometer mounted on the satellite are described briefly.

Williams, F. L.↗

Boron/aluminum skins for the DC-10 aft pylon

Three boron/aluminum aft pylon 'boat tail' skins were designed, fabricated, and installed on three DC-10 aircraft for a five-year flight service demonstration test. Inspection and tests of the skins will establish the ability of the composite to withstand long-time flight service exposures to high temperatures, sonic fatigue, and flutter. The results of a preliminary testing program yielded room and elevated temperature data on the tension, compression, in-plane shear, interlaminar shear, bolt bearing, and tension fatigue properties of the oriented eleven-ply boron/aluminum laminates, and this information, together with a stress analysis, was used to obtain Federal Aviation Administration approval. Present state-of-the-art technology was used in the fabrication of the skins, and these were installed on the existing titanium substructure with the same number and size mechanical fasteners as are used for the present titanium skins.

Elliott, S. Y.↗

An analysis of radio interferometry with the block O system

The form and flow of information from signal reception to recorded bits at each station, through cross-correlation, phase-tracking, phase calibration, and bandwidth synthesis, to final observable formation are traced. In this process the data volume is greatly compressed for each observation, from approx. 10 to the 9th power bits on the station tapes to only four final observables: amplitude, delay, phase-delay rate and RF phase. After phase calibration and propagation media calibrations, the final delay observable is shown to be the sum of a geometric delay and a clock synchronization offset.

Thomas, J. B.↗

Method and apparatus for Delta Kappa synthetic aperture radar measurement of ocean current

A synthetic aperture radar (SAR) employed for delta k measurement of ocean current from a spacecraft without the need for a narrow beam and long observation times. The SAR signal is compressed to provide image data for different sections of the chirp band width, equivalent to frequencies and a common area for the separate image fields is selected. The image for the selected area at each frequency is deconvolved to obtain the image signals for the different frequencies and the same area. A product of pairs of signals is formed, Fourier transformed and squared. The spectrum thus obtained from different areas for the same pair of frequencies are added to provide an improved signal to noise ratio. The shift of the peak from the center of the spectrum is measured and compared to the expected shift due to the phase velocity of the Bragg scattering wave. Any difference is a measure of current velocity v sub o (delta k).

Jain, A.↗

Spacecraft heat transfer by two-phase flow method

A refrigerator/freezer has been designed with an oil-free compressor to provide an economical two-phase flow system for heat transfer. A computer simulation has been done for the condenser and evaporator to determine the design parameters, such as length, diameter, and flow regimes, for different refrigerants and load requirements. A large Reynolds number was considered to ensure annular flow (in order to maximize heat transfer coefficients) and large Froude number. The simulation was correlated with the test data of a vapor compression refrigerator/freezer flown on STS-4 (which provided information on vapor compression in a zero-gravity environment). The two-phase system will be used for the Spacelab mission SLS-1 and can be used in future spacecraft and high-speed aircraft, where weight, volume, and power requirements are critical.

Hye, A.↗

The Radar Ocean-Wave Spectrometer

The scanning-beam Radar Ocean-Wave Spectrometer (ROWS) technique is described. The derivation of a spectrum for the reflectivity modulation as a function of range is examined. The usefulness of the ROWS technique was initially validated using aircraft data obtained in 1978 with the GSFC Ku-band pulse-compression radar; additional examples of aircraft data which verify the effectiveness of the ROWS technique are presented. The development of a ROWS mode for Spectrasat is discussed. Consideration is given to the incidence angle, twin beam option for cross-section roll-off and wind vector determination, rotation rate, antenna and footprint dimensions, integration time, sphericity effects, and a processor configuration. A design for the ROWS-mode time-domain processor on Spectrasat is proposed. The performance of the system is evaluated, and it is determined that the system performs well.

Jackson, Frederick C.↗

Synthetic-Aperture Radar Processor For Large Drift Angle

Digital signal-processing system makes images of terrain from synthetic-apperture-radar returns to airplane flying at large drift angle. Output of system includes high-resolution images, four-look images, magnitude/phase-difference images, and "compressed," all-inclusive data sets. Magnitude/phase-difference images produced by correlating images of like polarizations. Useful for investigating phase characteristics of targets in different polarizations.

Lou, Yun-Ling↗

Miniature PCM compatible wideband spectral analyzer for hypersonic flight research

The design concept and prototype performance of a 10-400-kHz wideband spectral analyzer being developed at NASA Langley as part of the Hypersonic Flight Instrumentation Research Experiment are described and illustrated with diagrams and graphs. The analyzer is intended to compress the bandwidth of data from up to 20 hot-film anemometers, so that the analog PSD waveform from each sensor can be encoded for serial PCM telemetry. Components include an analog multiplier, digital waveform generator, sine-wave VCO, digital VCO, analog low-pass filter, switched-capacitor filter, and rms-dc detector. The prototype demonstrated 1-percent accuracy (referred to a 5-V full-scale output) for sweep rates up to 3/sec over the 10-400-kHz spectrum.

Diamond, John K.↗

A test method to measure the response of composite materials under reversed cyclic loads

A test method to measure the response of composite materials under reversed cyclic loads is described. The method approximates the long-term response of a component by permitting the composite specimen to respond to the imposed loads and fail in an unconstrained mode rather than in a constrained mode. The method has been successfully used for the reversed cyclic loading of unnotched and notched graphite/epoxy and graphite/PEEK laminates of various stacking sequences. Included in the paper are monotonic tensile and compressive stiffness and strength data at several points in the fatigue lifetime, and damage development information obtained via X-ray radiography for quasi-isotropic T300/5208 and AS4/PEEK laminates with unloaded circular holes.

Bakis, Charles E.↗

A very high speed lossless compression/decompression chip set

A chip is described that will perform lossless compression and decompression using the Rice Algorithm. The chip set is designed to compress and decompress source data in real time for many applications. The encoder is designed to code at 20 M samples/second at MIL specifications. That corresponds to 280 Mbits/second at maximum quantization or approximately 500 Mbits/second under nominal conditions. The decoder is designed to decode at 10 M samples/second at industrial specifications. A wide range of quantization levels is allowed (4...14 bits) and both nearest neighbor prediction and external prediction are supported. When the pre and post processors are bypassed, the chip set performs high speed entropy coding and decoding. This frees the chip set from being tied to one modeling technique or specific application. Both the encoder and decoder are being fabricated in a 1.0 micron CMOS process that has been tested to survive 1 megarad of total radiation dosage. The CMOS chips are small, only 5 mm on a side, and both are estimated to consume less than 1/4 of a Watt of power while operating at maximum frequency.

Venbrux, Jack↗

Experiments on shear layer mixing at hypervelocity conditions

Utilization of an expansion tube to acquire turbulent, compressible free shear layer data with gases of direct relevance to hypersonic combustion systems (nitrogen, hydrogen, and oxygen) is demonstrated. Visualizations of the free shear layer by laser holographic interferometry and schlieren imaging show a distinctly asymmetric growth rate that is highly preferential toward the lower speed (secondary stream) side. For the nitrogen/nitrogen case, for which the convective velocity was lowest and convective Mach number highest, the growth rate on the primary side was virtually zero until the mixing layer reached the opposite (secondary) wall.

Erdos, John↗

Compressive strength of directionally solidified NiAl-NiAlNb intermetallics at 1200 and 1300 K

Results are presented from measurements of 1200 K and 1300 K compressive properties of two directionally solidified NiAl-NiAlNb compositions (in at. pct): Ni-41.75Al-16.5Nb (eutectic composition) and Ni-47.5Al-8.9Nb-1.3C (Al-rich composition). Results showed that the strength of the eutectic was a factor of 2 greater than that of the Al-rich composition. However, the analysis of the compressive stress-strain data indicated that the deformation mechanism was the same in both materials.

Whittenberger, J. D.↗

A Subpress for Compressive Tests

A subpress for compressive tests is described. The subpress was designed primarily for use in developing and investigating methods for testing thin sheet metal in compression. Provision was made for testing fixed-end and flat-end specimens with or without various types of lateral support against buckling. Compressive stress-strain data for a sheet of 0.032-inch 24S-RT aluminum alloy were obtained with the subpress by the pack method and by the single-thickness method. The data showed small scatter and the stress-strain curves obtained by the two methods were in close agreement.

Aitchison, C S↗